Morphology and electrical properties of polymethylmethacrylate/poly(styrene‐co‐acrylonitrile)/multi‐walled carbon nanotube nanocomposites

Nanocomposites of blends of polymethylmethacrylate (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with multi‐walled carbon nanotubes (MWCNTs) were prepared by melt mixing in a twin‐screw extruder. The dispersion state of MWCNTs in the matrix polymers was investigated using transmission electron microscopy. Interestingly enough, in most of the nanocomposites, the MWCNTs were observed to be mainly located at SAN domains, regardless of the SAN compositions in the PMMA/SAN blend and of the processing method. One possible reason for this morphology may be the π–π interactions between MWCNTs and the phenyl ring of SAN. The shift in G‐band peak observed in the Raman spectroscopy may be the indirect evidence proving these interactions. The percolation threshold for electrical conductivity of PMMA/SAN/MWCNT nanocomposites was observed to be around 1.5 wt %. Nanocomposites with PMMA‐rich composition showed higher electrical conductivity than SAN‐rich nanocomposites at a fixed MWCNT loading. The dielectric constant measurement also showed composition‐dependent behavior. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

An Effective Strategy to Achieve Ultralow Electrical Percolation Threshold with CNTs Anchoring at the Interface of PVDF/PS Bi‐Continuous Structures to Form an Interfacial Conductive Layer

Conductive composites based on polymers and conductive nanofillers are widely studied as a promising material. The rational design of 3D conductive networks in composites is crucial to improve their electrical conductivity and reduce the dosage of nanofillers. Herein, poly(vinylidene fluoride) (PVDF) and polystyrene (PS) bi‐continuous structures with modified carbon nanotubes (CNTs) tailored to anchor at the interface are designed to achieve an ultralow electrical percolation threshold because of the formation of a thin interfacial conductive layer. In this work, the modification of CNTs with poly(methyl methacrylate) (PMMA), which contributes to the improvement of the compatibility between PVDF and CNTs, is effective to control the distribution of CNTs in composites. It promotes the migration of CNTs from the PS phase to the interface of PVDF and PS. Consequently, the interfacial conductive layer is formed at a low CNT content, and the electrical percolation threshold of PVDF/PS/CNTs‐PMMA nanocomposites is only 0.07 vol%, having a great decrease of about 50% compared with that of PVDF/PS/CNTs nanocomposites. Thus, it is demonstrated that the distribution of CNTs can be tailored to anchor at the interface by proper chemical modification to form an interfacial conductive layer and a decrease of percolation threshold can also be achieved.     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

The characteristics of carbon nanotube‐reinforced poly(phenylene sulfide) nanocomposites

Multiwall carbon nanotube reinforced poly (phenylene sulfide) (PPS) nanocomposites were successfully fabricated through melt compounding. Structural, electrical, thermal, rheological, and mechanical properties of the nanocomposites were systematically studied as a function of carbon nanotube (CNT) fraction. Electrical conductivity of the polymer was dramatically enhanced at low loading level of the nanotubes; the electrical percolation threshold lay between 1 and 2 wt % of the CNTs. Rheological properties of the PPS nanocomposites also showed a sudden change with the CNT fraction; the percolation threshold was in the range of 0–0.5 wt % of CNTs. The difference in electrical and rheological percolation threshold was mainly due to the different requirements needed in the carbon nanotube network in different stages. The crystallization and melting behavior of CNT‐filled PPS nanocomposites were studied with differential scanning calorimetry; no new crystalline form of PPS was observed in the nanocomposites, but the crystallization rate was reduced. The thermal and mechanical properties of the nanocomposites were also investigated, and both of them showed significant increase with CNT fraction. For 5 wt % of CNT‐filled PPS composite, the onset of degradation temperature increased by about 13.5°C, the modulus increased by about 33%, and tensile strength increased by about 172%. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Nanophase morphology and crystallization in poly(vinylidene fluoride)/polydimethylsiloxane‐block‐poly(methyl methacrylate)‐block‐polystyrene blends

An approach to achieve confined crystallization of ferroelectric semicrystalline poly(vinylidene fluoride) (PVDF) was investigated. A novel polydimethylsiloxane‐block‐poly(methyl methacrylate)‐block‐polystyrene (PDMS‐b‐PMMA‐b‐PS) triblock copolymer was synthesized by the atom‐transfer radical polymerization method and blended with PVDF. Miscibility, crystallization and morphology of the PVDF/PDMS‐b‐PMMA‐b‐PS blends were studied within the whole range of concentration. In this A‐b‐B‐b‐C/D type of triblock copolymer/homopolymer system, crystallizable PVDF (D) and PMMA (B) middle block are miscible because of specific intermolecular interactions while A block (PDMS) and C block (PS) are immiscible with PVDF. Nanostructured morphology is formed via self‐assembly, displaying a variety of phase structures and semicrystalline morphologies. Crystallization at 145 °C reveals that both α and β crystalline phases of PVDF are present in PVDF/PDMS‐b‐PMMA‐b‐PS blends. Incorporation of the triblock copolymer decreases the degree of crystallization and enhances the proportion of β to α phase of semicrystalline PVDF. Introduction of PDMS‐b‐PMMA‐b‐PS triblock copolymer to PVDF makes the crystalline structures compact and confines the crystal size. Moreover, small‐angle X‐ray scattering results indicate that the immiscible PDMS as a soft block and PS as a hard block are localized in PVDF crystalline structures. © 2019 Society of Chemical Industry     

Effect of poly(methyl methacrylate) addition on the dielectric and energy storage properties of poly(vinylidene fluoride)

Poly(methyl methacrylate) (PMMA) was introduced into poly(vinylidene fluoride) (PVDF) via a solution blending process, and a series of PVDF/PMMA blends were obtained in an effort to reduce the energy loss of pure PVDF. The effects of the composition and thermal treatment on the properties of the polymer blends were carefully studied. The results show that the introduction of PMMA led to a lower crystallinity and a smaller crystal size of PVDF for its dilution effect. As a result, the dielectric constant and energy storage density of the polymer blends were slightly reduced. Meanwhile, the phase transition of the PVDF crystals from the α phase to the β phase happened during the quenching of the blend melt to ice–water; this was also observed in the untreated or annealed blends with PMMA contents over 50 wt %. Compared with the α‐PVDF, the PVDF crystals in the β phase possessed a lower melting temperature, a higher dielectric constant, and a lower dielectric loss. The addition of PMMA reduced the energy loss of PVDF significantly, whereas the energy storage density decreased slightly. The optimized blend film with about 40 wt % PMMA and PVDF in the β phase showed a relative high energy storage density and the lowest energy loss. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Investigation of the crystalline structure of PVDF in PVDF/PMMA/graphene polymer blend nanocomposites

In this work, we report the preparation of poly(vinylidene fluoride)/poly methylmethacrylate (PVDF/PMMA)/graphene polymer blend nanocomposites via synthesis of PMMA/graphene as a masterbatch through in situ polymerization. The PMMA/graphene masterbatch compounded with PVDF by solution mixing in different ratios. The compounding was followed by solution casting to form polymer blend nanocomposites. Solution cast films were subjected to thermal treatments at three different temperatures. The crystalline structure of thermally treated samples was studied with X‐ray diffraction spectroscopy and Differential Scanning Calorimetric (DSC) analysis. Results indicated PMMA chains persuade the β crystalline form in PVDF but cannot stabilize them in elevated temperature; however, graphene sheets due to restricting effect on TT conformation chains are able to stabilize them. DSC data revealed the graphene sheets can increase the crystallinity of PVDF and also act as nucleating agents. Transmission Electron Microscopy demonstrated coexistence of the different stacking orders of graphene sheets in both masterbatch and polymer blend nanocomposite. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

A facile route to develop electrical conductivity with minimum possible multi‐wall carbon nanotube (MWCNT) loading in poly(methyl methacrylate)/MWCNT nanocomposites

Today, we stand at the threshold of exploring carbon nanotube (CNT) based conducting polymer nanocomposites as a new paradigm for the next generation multifunctional materials. However, irrespective of the reported methods of composite preparation, the use of CNTs in most polymer matrices to date has been limited by challenges in processing and insufficient dispersability of CNTs without chemical functionalization. Thus, development of an industrially feasible process for preparation of polymer/CNT conducting nanocomposites at very low CNT loading is essential prior to the commercialization of polymer/CNT nanocomposites. Here, we demonstrate a process technology that involves in situ bulk polymerization of methyl methacrylate monomer in the presence of multi‐wall carbon nanotubes (MWCNTs) and commercial poly(methyl methacrylate) (PMMA) beads, for the preparation of PMMA/MWCNT conducting nanocomposites with significantly lower (0.12 wt% MWCNT) percolation threshold than ever reported with unmodified commercial CNTs of similar qualities. Thus, a conductivity of 4.71 × 10^?5 and 2.04 × 10^?3 S cm^?1 was achieved in the PMMA/MWCNT nanocomposites through a homogeneous dispersion of 0.2 and 0.4 wt% CNT, respectively, selectively in the in situ polymerized PMMA region by using 70 wt% PMMA beads during the polymerization. At a constant CNT loading, the conductivity of the composites was increased with increasing weight percentage of PMMA beads, indicating the formation of a more continuous network structure of the CNTs in the PMMA matrix. Scanning and transmission electron microscopy studies revealed the dispersion of MWCNTs selectively in the in situ polymerized PMMA phase of the nanocomposites. Copyright © 2012 Society of Chemical Industry     

Conductive poly(vinylidene fluoride)/polyethylene/graphene blend‐nanocomposites: Relationship between rheology,morphology, and electrical conductivity

Relationship between rheology, morphology, and electrical conductivity of the poly(vinylidene fluoride)/polyethylene/graphene nano‐platelets ternary system (PVDF/PE/GnP) were investigated. All the blend nanocomposites were prepared via a two‐step melt mixing method. GnP (0.75 and 1.5 wt %) was first compounded with PVDF and then the resulted premixtuers were melt mixed with PE to achieve the desired compositions. The corresponding reference nanocomposites and filler‐less blends were also prepared. Effect of an interfacial agent (PEMA; maleic anhydride grafted polyethylene) was also studied in this work. The results of rheological analysis in conjunction with the Raman spectroscopy experiments revealed that GnP had higher affinity to PVDF than PE, which in turn led to creation of conductive networks of GnP (1.5 wt %) in PVDF matrix exhibiting the electrical conductivity of about 10^?2 (S/cm). Double percolated micro‐structure was predicted for the PE/PVDF 40/60 (wt/wt) blend containing low GnP content (0.9 wt %) and confirmed via direct electron microscopy and conductivity analysis. Using 5 wt % of the PEMA reduced the conductivity to 10^?5 (S/cm) and further increase in PEMA content to 10 wt % led to non‐conductive characteristics. The latter was attributed to the migration of GnP from the PVDF phase to PE/PEMA phase and hence disturbance of double percolated micro‐structure. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46333.     

Investigation on crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends by solution casting

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by solution casting. The crystallization behavior and hydrophilicity of ternary blends were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), wide angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and contact angle test. According to morphological analysis, the surface was full of typical spherulitic structure of PVDF and the average diameter was in the order of 3 μm. The samples presented predominantly β phase of PVDF by solution casting. It indicated that the size of surface spherulites and crystalline phase had little change with the PMMA or PVP addition. Moreover, FTIR demonstrated special interactions among the ternary polymers, which led to the shift of the carbonyl stretching absorption band of PVP. On the other hand, the melting, crystallization temperature, and crystallinity of the blends had a little change compared with the neat PVDF in the first heating process. Except for the content of PVP containing 30 wt %, the crystallinity of PVDF decreased remarkably from 64% to 33% and the value of t_1/2 was not obtained. Besides, the hydrophilicity of PVDF was remarkably improved by blending with PMMA/PVP, especially when the content of PVP reached 30 wt %, the water contact angle displayed the lowest value which decreased from 98.8° to 51.0°. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Integration of PDA Chemistry and Surface‐Initiated ATRP to Prepare Poly(methyl methacrylate)‐Grafted Carbon Nanotubes and Its Effect on Poly(vinylidene fluoride)–Carbon Nanotube Composite Properties

Poly(methyl methacrylate)‐grafted carbon nanotubes (PMMA@MWCNTs) are nondestructively prepared via the integration of mussel‐inspired polydopamine (PDA) chemistry and the surface‐initiated atom transfer radical polymerization (ATRP) method. The structures and properties of the poly(vinylidene fluoride)‐based (PVDF‐based) nanocomposites filled with pristine MWCNTs and PMMA@MWCNTs are investigated. The results show that the encapsulation of PMMA on the MWCNTs surface not only improves the dispersibility of MWCNTs in the PVDF matrix but also enhances the interfacial interaction between MWCNTs and PVDF. The addition of PMMA@MWCNTs nanofillers to PVDF can effectively induce the crystal structure of PVDF to transform from the α‐phase to the β/γ ‐phase, and nearly 100% β/γ ‐phase PVDF formed when the nanofiller loading is higher than 5 wt%. Compared with the MWCNTs/PVDF composites, the PMMA@MWCNTs/PVDF composites exhibit obvious improvement in the percolation threshold because the PMMA shells hinder the direct contact of the MWCNTs. Moreover, the loss tangent of the PMMA@MWCNTs/PVDF composites is effectively suppressed due to the reduced leakage current in the composites and the enhanced interfacial strength between the nanofiller and the matrix.     

Effect of surface treatment for carbon nanotubes on morphological and rheological properties of poly(ethylene oxide) nanocomposites

Poly(ethylene oxide) nanocomposites filled with functionalized multi‐walled carbon nanotubes are prepared and characterized using rheological and morphological measurements. This study investigates how the surface treatment of carbon nanotubes (CNTs) affects the CNT dispersion state. It is found that the nanocomposites have a higher effective volume fraction than the real volume fraction of the CNTs. The dispersion state of the CNTs is identified by using field emission scanning electron spectroscope and transmission electron microscope. The rheological findings indicate that there exists a percolated network structure of the CNTs in the nanocomposites, which was confirmed by electrical conductivity measurements as well as morphological observation. POLYM. ENG. SCI., 46:1350–1357, 2006. © 2006 Society of Plastics Engineers     

PVDF/PMMA composite nanofiber fabricated by electrospray deposition: Crystallization of PVDF induced by solvent extraction of PMMA component

The crystallization of poly(vinylidene fluoride) (PVDF) was observed after the poly(methyl methacrylate) (PMMA) component was extracted from the PVDF/PMMA (50/50) composite nanofiber fabricated by electrospray deposition, even though the original composite showed a completely amorphous pattern in the wide‐angle X‐ray diffraction. The content of the β‐crystal form in the crystalline region depended on the PVDF/PMMA composite ratios and the type of solvents used for the extraction of the PMMA component, e.g., chloroform and toluene. Thus, the content of the β‐crystal form can be controlled by selecting the original PVDF/PMMA composition and the solvent used to extract the PMMA component. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polymer electrolyte membranes composed of an electrospun poly(vinylidene fluoride) fibrous mat in a poly(4‐vinylpyridine) matrix

Newly proposed polymer electrolyte membranes (PEMs) composed of an electrospun poly(vinylidene fluoride) (PVDF) fibrous mat embedded in a poly(4‐vinylpyridine) (P4VP) matrix were successfully fabricated in order to improve the mechanical and dimensional stabilities and ionic conductivity of membranes in lithium rechargeable batteries. Fourier transform infrared spectroscopic analysis showed that as a result of the use of a high voltage during electrospinning the crystalline structure of PVDF changed partially from α‐phase to β‐phase. Energy‐dispersive X‐ray spectroscopy confirmed the existence of crosslinked P4VP in the PVDF fibrous mat. The electrolyte uptakes of PVDF and PVDF/P4VP composite mats were higher than that of PVDF cast film. The tensile properties of PVDF/P4VP composite mat were considerably improved compared to those of the pristine PVDF fibrous mat under both dry and wet (soaked with electrolyte) conditions. In addition, the mechanical and dimensional stabilities of the PVDF/P4VP composite PEM were further enhanced due to crosslinking between the P4VP chains. Furthermore, the PVDF/P4VP composite PEM exhibited an ionic conductivity that was an order of magnitude higher than that of traditional PVDF film. © 2012 Society of Chemical Industry     

Membrane formation of poly(vinylidene fluoride)/poly(methyl methacrylate)/diluents via thermally induced phase separation

The role of the single diluents and mixed diluents on the poly (vinylidene fluoride) (PVDF)/poly(methyl methacrylate) (PMMA) blend membranes via thermally induced phase separation (TIPS) process was investigated. The crystallization behaviors of PVDF in the diluted samples were examined by differential scanning calorimetry. The melting and crystallization temperatures of those diluted PVDF blend were decreased with the enhanced interactions between polymer chains and diluent molecules. The crystallinity of PVDF in the diluent was always higher than that obtained in PVDF blend sample. This can be explained by the dilution effects, which increased the average spatial separation distances between crystallizable chains. Thus, the PVDF crystallization was favored. Additionally, solid‐liquid (S‐L) phase separation occurred in the quenched samples. Illustrated by scanning electron microscopy, inter‐ and intraspherulitic voids were formed in the ultimate membranes, which related to the polymer/diluent interactions, the kinetics of crystallization and diluent rejection from the growing crystal. The porosity of the PVDF blend membranes obtained from the mixed diluents was higher than those obtained from the single diluent samples. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Investigation of electrical conduction mechanism in double‐layered polymeric system

The electrical conduction in solution‐grown polymethylmethacrylate (PMMA), polyvinylidenefluoride (PVDF) and PMMA‐PVDF double‐layered samples in the sandwich configuration (metal‐polymer‐metal) was investigated at different fields in the range 100–120 kV/cm as a function of temperature in the range 293–423 K for samples of constant thickness of about 50 μm. Certain effects which lead to a large burst of current immediately after the application of field were observed in double‐layered samples. An attempt was made to identify the nature of the current by comparing the observed dependence on electric field, electrode material and temperature with the respective characteristic features of the existing theories on electrical conduction. The observed linear I‐V characteristics show that the electrical conduction follows Pool‐Frenkel mechanism in PMMA and PVDF samples. Whereas, the non‐linear behavior of current‐voltage measurements in PMMA‐PVDF double‐layered samples have been interpreted on the basis of space charge limited conduction (SCLC) mechanism. The conductivity of the polymer films increased on formation of their double‐layer laminates. The polymer‐polymer interface act as charge carrier trapping centres and provides links between the polymer molecules in the amorphous region. The interfacial phenomenon in polymer‐polymer heterogeneous system has been interpreted in terms of Maxwell‐Wagner model. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Role of poly(lactic acid) in the phase transition of poly(vinylidene fluoride) under uniaxial stretching

The effect of poly (lactic acid) (PLA) on the crystalline phase transition of poly (vinylidene fluoride) (PVDF) from α‐ to β‐phase under uniaxial stretching for immiscible PVDF/ PLA blends was investigated. The typical sea‐island structure in the blends was found to facilitate the necking of PVDF and the transition from α‐ to β‐phase due to the local stress distribution during stretching. The crystalline phase transition of PVDF in the blends is temperature‐dependent and is affected by the content of PLA. The highest content of β‐phase, F(β), was achieved in the samples stretched at 60°C, while the effect of PLA content on the crystalline phase transition of PVDF is more complex. F(β) increases slightly when the sample with a PLA content no more than 15 wt % is stretched at 60, 80, and 100°C, and decreases sharply for the sample containing 20 wt % PLA; in addition, the sample containing 10 wt % PLA exhibits the highest F(β) no matter what the stretching temperature is. The mechanism of the crystalline phase transition of PVDF during the stretching is interpreted from energy barrier of the transition from α‐ to β‐phase and the morphological structures in the blends. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Miscibility of C60‐containing poly(methyl methacrylate)/poly(vinylidene fluoride) blends

The miscibility of C₆₀‐containing poly(methyl methacrylate) (PMMA‐C₆₀) with poly(vinylidene fluoride) (PVDF) was studied. Two PMMA‐C₆₀ samples containing 2.6 and 7.4 wt % C₆₀ were found to be miscible with PVDF based on single glass transition temperature criterion and melting point depression of PVDF. However, the interaction parameters of the two blend systems are less negative than that of the PMMA/PVDF blend system, showing that the incorporation of C₆₀ reduces the ability of carbonyl groups of PMMA to interact with PVDF. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1393–1396, 2000     

Nanophase morphology and crystallization in poly(vinylidene fluoride)/polydimethylsiloxane‐block‐poly(methyl methacrylate) blends

A polydimethylsiloxane‐block‐poly(methyl methacrylate) (PDMS‐b‐PMMA) diblock copolymer was synthesized by the atom transfer radical polymerization method and blended with a high‐molecular‐weight poly(vinylidene fluoride) (PVDF). In this A‐b‐B/C type of diblock copolymer/homopolymer system, semi‐crystallizable PVDF (C) and PMMA (B) block are miscible due to favorable intermolecular interactions. However, the A block (PDMS) is immiscible with PVDF and therefore generates nanostructured morphology via self‐assembly. Crystallization study reveals that both α and γ crystalline phases of PVDF are present in the blends with up to 30 wt% of PDMS‐b‐PMMA block copolymer. Adding 10 wt% of PVDF to PDMS‐b‐PMMA diblock copolymer leads to worm‐like micelle morphology of PDMS of 10 nm in diameter and tens of nanometers in length. Moreover, morphological results show that PDMS nanostructures are localized in the inter‐fibrillar region of PVDF with the addition of up to 20 wt% of the block copolymer. Increase of PVDF long period by 45% and decrease of degree of crystallization by 34% confirm the localization of PDMS in the PVDF inter‐fibrillar region. © 2018 Society of Chemical Industry     

Nanocomposite films of poly(vinylidene fluoride) filled with polyvinylpyrrolidone‐coated multiwalled carbon nanotubes: Enhancement of β‐polymorph formation and tensile properties

To improve interactions between carbon nanotubes (CNTs) and poly(vinylidene fluoride) (PVDF) matrix, multiwalled CNTs (MWCNTs) were successfully coated with amphiphilic polyvinylpyrrolidone (PVP) using an ultrasonication treatment performed in aqueous solution. It was found that PVP chains could be attached noncovalently onto the nanotubes' surface, enabling a stable dispersion of MWCNTs in both water and N,N‐dimethylformamide. PVP‐coated MWCNTs/PVDF nanocomposite films were prepared by a solution casting method. The strong specific dipolar interaction between the PVP's carbonyl group (C?O) and the PVDF's fluorine group C?F₂ results in high compatibility between PVP and PVDF, helping PVP‐coated MWCNTs to be homogenously dispersed within PVDF. Fourier transform infrared and X‐ray diffraction characterization revealed that the as‐prepared nanocomposite PVDF films exhibit a purely β‐polymorph even at a very low content of PVP‐wrapped MWCNTs (0.1 wt%) while this phase is totally absent in the corresponding unmodified MWCNTs/PVDF nanocomposites. A possible mechanism of β‐phase formation in PVP‐coated MWCNTs/PVDF nanocomposites has been discussed. Furthermore, the tensile properties of PVDF nanocomposites as function of the content in PVP‐coated MWCNTs were also studied. Results shows that the addition of 2.0 wt% of PVP‐coated MWCNTs lead to a 168% increase in Young's modulus and a 120% in tensile strength. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers