The physical–chemical properties and electrocatalytic performance of iridium oxide in oxygen evolution

An IrO₂ anode catalyst was prepared by using the Adams method for the application of a solid polymer electrolyte (SPE) water electrolyzer. The effect of calcination temperature on the physical–chemical properties and the electrochemical performance of IrO₂ were examined to obtain a low loading and a high catalytic activity of oxygen evolution at the electrode. The physical–chemical properties were studied via thermogravimetry–differential scanning calorimetry (TG–DSC), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The electrochemical activity was investigated by using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and chronopotentiometry in 0.1 mol L⁻¹ H₂SO₄ at room temperature. The optimum condition was found to be at the calcination temperature of 500 °C, where the total polarization reached a minimum at high current densities (>200 mA cm⁻²). The optimized catalyst was also applied to a membrane electrode assembly (MEA) and stationary current–potential relationships were investigated. With an optimized catalytic IrO₂ loading of 1.5 mg cm⁻² and a 40% Pt/C loading of 0.5 mg cm⁻², the terminal applied potential difference was 1.72 V at 2 A cm⁻² and 80 °C in a SPE water electrolysis cell.     

Sulfur–carbon composite electrode for all-solid-state Li/S battery with Li2S–P2S5 solid electrolyte

All-solid-state Li/S batteries with Li₂S–P₂S₅ glass–ceramic electrolytes were fabricated and their electrochemical performance was examined. Sulfur–carbon composite electrodes were prepared by grinding with a mortar and milling with a planetary ball-mill apparatus. Milling of a mixture of sulfur, acetylene black and the Li₂S–P₂S₅ glass–ceramic electrolyte resulted in the amorphization of sulfur and a reduction in the particle size of the mixture. The charge–discharge properties of all-solid-state cells with the composite electrode were investigated at temperatures from −20 °C to 80 °C. The cells retained a reversible capacity higher than 850 mAh g⁻¹ for 200 cycles under 1.3 mA cm⁻² (333 mA g⁻¹) at 25 °C. The cell performance was influenced by the crystallinity of sulfur and the particle size of the electrode material, whereby improved contact among the electrode components achieved by milling contributed to enhancement of the capacity of an all-solid-state Li/S cell.     

Effects of 1,3-dialkylimidazolium cations with different lengths of alkyl chains on the Pt electrode/electrolyte interface in dye-sensitized solar cells

The electrochemical behaviors of the tri-iodide (I₃⁻)/iodide (I⁻) redox couple of symmetric cells were investigated by cyclic voltammetry, steady-state polarization, chronocoulometry, and electrochemical impedance spectroscopy. 1,3-Dialkylimidazolium cations affected the characteristics of the Pt electrode/electrolyte interface by adsorbing on the Pt electrode, as a result of electrostatic interactions, and further affected the reduction of I₃⁻ on the Pt electrode. Capacitance of the double layers of the Pt electrode/electrolyte interface was chiefly determined by capacitance of the compact layer according to the Helmoholtz theory.     

In situ electrochemical oxidation of ethylenediamine on Co–B alloy electrode during cycling for improving its electrochemical properties at elevated temperature

A Co–B alloy/ethylenediamine (EDA) hybrid electrode system has been developed by adding EDA into electrolyte. Charge–discharge measurements show that the inorganic–organic hybrid electrode system exhibits high discharge capacity and long cycle life at elevated temperature (55 °C). Specifically, in the electrolyte containing 0.09 M EDA additive, the discharge capacity of Co–B alloy electrode after 100 cycles is still up to 601.7 m Ah g⁻¹ at 55 °C. However, for the electrode in EDA-free electrolyte, its discharge capacity is sharply decreased to only 138.5 m Ah g⁻¹ after 100 cycles. ICP-OES and IR measurements are used to clarify the reason of the improvement in the electrochemical properties. These results show that beneficial effect of EDA on electrochemical properties of Co–B alloy electrode can be attributed to in situ electrochemical oxidation of EDA during discharge cycles. First the oxidation of EDA contributes to part of the discharge capacity and secondly the oxidation products absorbed on the electrode may help to suppress the dissolution of Co at elevated temperature. Evidence is presented suggesting that the oxidation of Co can induce co-oxidation of EDA.     

Gold nanoparticles/water-soluble carbon nanotubes/aromatic diamine polymer composite films for highly sensitive detection of cellobiose dehydrogenase gene

An electrochemical sensor based on gold nanoparticles (GNPs)/multiwalled carbon nanotubes (MWCNTs)/poly (1,5-naphthalenediamine) films modified glassy carbon electrode (GCE) was fabricated. The effectiveness of the sensor was confirmed by sensitive detection of cellobiose dehydrogenase (CDH) gene which was extracted from Phanerochaete chrysosporium using polymerase chain reaction (PCR). The monomer of 1,5-naphthalenediamine was electropolymerized on the GCE surface with abundant free amino groups which enhanced the stability of MWCNTs modified electrode. Congo red (CR)-functionalized MWCNTs possess excellent conductivity as well as high solubility in water which enabled to form the uniform and stable network nanostructures easily and created a large number of binding sites for electrodeposition of GNPs. The continuous GNPs together with MWCNTs greatly increased the surface area, conductivity and electrocatalytic activity. This electrode structure significantly improved the sensitivity of sensor and enhanced the DNA immobilization and hybridization. The thiol modified capture probes were immobilized onto the composite films-modified GCE by a direct formation of thiol–Au bond and horseradish peroxidase–streptavidin (HRP–SA) conjugates were labeled to the biotinylated detection probes through biotin–streptavidin bond. Scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) were used to investigate the film assembly and DNA hybridization processes. The amperometric current response to HRP-catalyzed reaction was linearly related to the common logarithm of the target nucleic acid concentration in the range of 1.0 × 10⁻¹⁵–1.0 × 10⁻¹⁰ M, with the detection limit of 1.2 × 10⁻¹⁶ M. In addition, the electrochemical biosensor exhibited high sensitivity, selectivity, stability and reproducibility.     

Sensitive DNA impedance biosensor for detection of cancer, chronic lymphocytic leukemia, based on gold nanoparticles/gold modified electrode

A simple and sensitive DNA impedance sensor was prepared for the detection of chronic lymphocytic leukemia. The DNA electrochemical biosensor is worked based on the electrochemical impedance spectroscopic (EIS) detection of the sequence-specific DNA related to chronic lymphocytic leukemia. The ssDNA probe was immobilized on the surface of the gold nanoparticles. Compared to the bare gold electrode, the gold nanoparticles-modified electrode could improve the density of the probe DNA attachment and hence the sensitivity of the DNA sensor greatly. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy were performed in a solution containing 1.0 mmol L⁻¹ K₃[Fe(CN)₆]/K₄[Fe(CN)₆] and 50 mmol L⁻¹ phosphate buffer saline pH 6.87 plus 50 mmol L⁻¹ KCl. In the CV studied, the potential was cycled from 0.0 to +0.65 V with a scan rate of 50 mV s⁻¹. Using EIS, the difference of the electron transfer resistance (ΔR_et) was linear with the logarithm of the complementary oligonucleotides sequence concentrations in the range of 7.0 × 10⁻¹²–2.0 × 10⁻⁷ mol L⁻¹, with a detection limit of 1.0 × 10⁻¹² mol L⁻¹. In addition, the DNA sensor showed a good reproducibility and stability during repeated regeneration and hybridization cycles.     

Symmetric lithium-ion cell based on lithium vanadium fluorophosphate with ionic liquid electrolyte

Lithium vanadium fluorophosphate, LiVPO₄F, was utilized as both cathode and anode for fabrication of a symmetric lithium-ion LiVPO₄F//LiVPO₄F cell. The electrochemical evolution of the LiVPO₄F//LiVPO₄F cell with the commonly used organic electrolyte LiPF₆/EC-DMC has shown that this cell works as a secondary battery, but exhibits poor durability at room temperature and absolutely does not work at increased operating temperatures. To improve the performance and safety of this symmetric battery, we substituted a non-flammable ionic liquid (IL) LiBF₄/EMIBF₄ electrolyte for the organic electrolyte. The symmetric battery using the IL electrolyte was examined galvanostatically at different rates and operating temperatures within the voltage range of 0.01–2.8 V. It was demonstrated that the IL-based symmetric cell worked as a secondary battery with a Coulombic efficiency of 77% at 0.1 mA cm⁻² and 25 °C. It was also found that the use of the IL electrolyte instead of the organic one resulted in the general reduction of the first discharge capacity by about 20–25% but provided much more stable behavior and a longer cycle life. Moreover, an increase of the discharge capacity of the IL-based symmetric battery up to 120 mA h g⁻¹ was observed when the operating temperature was increased up to 80 °C at 0.1 mA cm⁻². The obtained electrochemical behavior of both symmetric batteries was confirmed by complex-impedance measurements at different temperatures and cycling states. The thermal stability of LiVPO₄F with both the IL and organic electrolytes was also examined.     

Electrochemical and interfacial behavior of a FeSi2.7 thin film electrode in an ionic liquid electrolyte

A FeSi_2.7 thin film is deposited on a copper substrate by RF magnetron sputtering of a Fe–Si alloy target. The electrochemical behavior of the FeSi_2.7 electrode in ionic liquid electrolyte based on 1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl) imide is investigated and compared with that of a FeSi_2.7 electrode in conventional liquid electrolyte. The FeSi_2.7 electrode in the ionic liquid electrolyte delivers an initial discharge capacity of 756 mAh g⁻¹ at room temperature, and its discharge capacity is maintained to be 92% of the initial discharge capacity after the 100th cycle. AC impedance and FTIR analysis reveal that the formation of a stable solid electrolyte interphase (SEI) layer on the FeSi_2.7 electrode in the ionic liquid electrolyte leads to a good capacity retention. This study demonstrates that the FeSi_2.7 electrode exhibits stable cycling behavior and good interfacial characteristics in the ionic liquid electrolyte without any solvents and additives.     

Synthesis and electrochemical properties of lithium methacrylate-based self-doped gel polymer electrolytes

In this study, a strategy for synthesizing lithium methacrylate (LiMA)-based self-doped gel polymer electrolytes was described and the electrochemical properties were investigated by impedance spectroscopy and linear sweep voltammetry. LiMA was found to dissolve in ethylene carbonate (EC)/diethyl carbonate (DEC) (3/7, v/v) solvent after complexing with boron trifluoride (BF₃). This was achieved by lowering the ionic interactions between the methacrylic anion and lithium cation. As a result, gel polymer electrolytes consisting of BF₃-LiMA complexes and poly(ethylene glycol) diacrylate were successfully synthesized by radical polymerization in an EC/DEC liquid electrolyte. The FT-IR and AC impedance measurements revealed that the incorporation of BF₃ into the gel polymer electrolytes increases the solubility of LiMA and the ionic conductivity by enhancing the ion disassociations. Despite the self-doped nature of the LiMA salt, an ionic conductivity value of 3.0 × 10⁻⁵ S cm⁻¹ was achieved at 25 °C in the gel polymer electrolyte with 49 wt% of polymer content. Furthermore, linear sweep voltammetry measurements showed that the electrochemical stability of the gel polymer electrolyte was around 5.0 V at 25 °C.     

Preparation of gel polymer electrolytes using PMMA interpenetrating polymeric network and their electrochemical performances

A gel polymer electrolyte (GPE) is prepared from polymethylmethacrylate interpenetrating polymer network, benzoyl peroxide, and 1.1 M LiPF₆/EC-DEC (1:1 vol.%). The LiCoO₂/graphite cells are prepared and their electrochemical properties were evaluated at various current densities and temperatures. The viscosity of the precursor containing 5 vol.% curable mixture is around 4.6 mPa s. The ionic conductivity of the GPE at 20 °C is around 5.8×10⁻³ S cm⁻¹. The GPE has good electrochemical stability up to 4.8 V vs. Li/Li⁺. The capacity of the cell at 1.0C rate is 82% of the discharge capacity at 0.2C rate. The capacity of the cell at −10 °C is 86% of the discharge capacity at 20 °C. Discharge capacity of the cell with GPE is stable with charge-discharge cycling.     

Mesoporous nickel electrodes plated with gold for the detection of glucose

Mesoporous nickel electrodes (MNEs) are efficient structural materials for advanced electrochemical sensors due to their extremely high surface areas. However, the poor oxidation resistance of nano-sized nickel in air severely limits their applications. Thus, the purpose of the present study was to improve the oxidation resistance of MNEs by applying relatively stable gold coatings via electroplating. The results revealed that the gold coatings provided excellent oxidation resistance to MNEs, and a loss in amperometric sensitivity for glucose sensing was not observed. The protection time increased with an increase as the thickness of the gold coating (passing charges of 0–25.49 C/cm²), and protection times ranging from a few hours to 2 weeks were obtained. With an alkaline electrolyte (NaOH, 4 M), MNEs exhibited excellent sensitivities. For instance, the sensitivity of the unmodified MNE and the Au coated-MNE was 3238 and 2978 μA mM⁻¹ cm⁻², respectively. Thus, coated and uncoated MNEs displayed remarkably higher linear sensitivities than conventional nickel-based electrodes (394 μA mM⁻¹ cm⁻²) at a wide range of glucose concentrations (0.001–3 M).     

Synthesis and electrochemical characterization of PEO-based polymer electrolytes with room temperature ionic liquids

New gel polymer electrolytes containing 1-butyl-4-methylpyridinium bis(trifluoromethanesulfonyl)imide (BMPyTFSI) ionic liquid are prepared by solution casting method. Thermal and electrochemical properties have been determined for these gel polymer electrolytes. The addition of BMPyTFSI to the P(EO)₂₀LiTFSI electrolyte results in an increase of the ionic conductivity, and at high BMPyTFSI concentration (BMPy⁺/Li⁺ = 1.0), the ionic conductivity reaches the value of 6.9 × 10⁻⁴ S/cm at 40 °C. The lithium ion transference numbers obtained from polarization measurements at 40 °C were found to decrease as the amount of BMPyTFSI increased. However, the lithium ionic conductivity increased with the content of BMPyTFSI. The electrochemical stability and interfacial stability for these gel polymer electrolytes were significantly improved due to the incorporation of BMPyTFSI.     

Evaluation of BaZr0.1Ce0.7Y0.2O3−δ-based proton-conducting solid oxide fuel cells fabricated by a one-step co-firing process

Proton-conducting solid oxide fuel cells, incorporating BaZr_0.1Ce_0.7Y_0.2O_3−δ (BZCY) electrolyte, NiO–BZCY anode, and Sm_0.5Sr_0.5CoO_3−δ–Ce_0.8Sm_0.2O_2−δ (SSC–SDC) cathode, were successfully fabricated by a combined co-pressing and printing technique after a one-step co-firing process at 1100, 1150, or 1200 °C. Scanning electron microscope (SEM) results revealed that the co-firing temperature significantly affected not only the density of the electrolyte membrane but the grain size and porosity of the electrodes. Influences of the co-firing temperature on the electrochemical performances of the single cells were also studied in detail. Using wet hydrogen (2% H₂O) as the fuel and static air as the oxidant, the cell co-fired at 1150 °C showed the highest maximum power density (PD_max) of 552 and 370 mW cm⁻² at 700 and 650 °C, respectively, while the one co-fired at 1100 °C showed the highest PD_max of 276 and 170 mWcm⁻² at 600 and 550 °C, respectively. The Arrhenius equation was proposed to analyze the dependence of the PD_max on the operating temperature, and revealed that PD_max of the cell co-fired at a lower temperature was less dependent on operating temperature. The influences of the co-firing temperature on the resistances of the single cells, which were estimated from the electrochemical impedance spectroscopy measured under open circuit conditions, were also investigated.     

Improvement of the performance for quasi-solid-state supercapacitor by using PVA–KOH–KI polymer gel electrolyte

A quasi-solid-state supercapacitor was assembled by using alkaline polyvinyl alcohol and potassium iodide (PVA–KOH–KI) as gel electrolyte and activated carbons electrodes. The electrocapacitive properties of the supercapacitor were evaluated by cyclic voltammetry, galvanostatic charge–discharge, and electrochemical impedance spectroscopy techniques. The introduction of KI increases the ionic conductivity of electrolyte, and improves the pseudocapacitance of the electrode. The specific capacitances of the supercapacitor is 236.90 F g⁻¹, increasing by 74.28% compared to the PVA–KOH system at the same current density. The energy density and power density of the supercapacitor reach 7.80 Wh kg⁻¹ and 15.34 kW kg⁻¹, respectively. In addition, the supercapacitor exhibits excellent cycle-life stability.     

Physical and electrochemical properties of 1-(2-hydroxyethyl)-3-methyl imidazolium and N-(2-hydroxyethyl)-N-methyl morpholinium ionic liquids

Various ionic liquids (ILs) were prepared via metathesis reaction from two kinds of 1-(2-hydroxyethyl)-3-methyl imidazolium ([HEMIm]⁺) and N-(2-hydroxyethyl)-N-methyl morphorinium ([HEMMor]⁺) cations and three kinds of tetrafluoroborate ([BF₄]⁻), bis(trifluoromethanesulfonyl)imide ([TFSI]⁻) and hexafluorophosphate ([PF₆]⁻) anions. All the [HEMIm]⁺ derivatives were in a liquid state at room temperature. In particular, [HEMIm][BF₄] and [HEMIm][TFSI] showed no possible melting point from −150 °C to 200 °C by DSC analysis, and their high thermal stability until 380-400 °C was verified by TGA analysis. Also, their stable electrochemical property (electrochemical window of more than 6.0 V) and high ionic conductivity (0.002-0.004 S cm⁻¹) further confirm that the suggested ILs are potential electrolytes for use in electrochemical devices. Simultaneously, the [HEMMor]⁺ derivatives have practical value in electrolyte applications because of their easy synthesis procedures, cheap morpholinium cation sources and possibilities of high Li⁺ mobility by oxygen group in the morpholinium cation. However, [HEMMor]⁺ derivatives showing high viscosity usually had lower ionic conductivities than [HEMIm]⁺ derivatives.     

High flash point electrolyte for use in lithium-ion batteries

The high flash point solvent adiponitrile (ADN) was investigated as co-solvent with ethylene carbonate (EC) for use as lithium-ion battery electrolyte. The flash point of this solvent mixture was more than 110 °C higher than that of conventional electrolyte solutions involving volatile linear carbonate components, such as diethyl carbonate (DEC) or dimethyl carbonate (DMC). The electrolyte based on EC:ADN (1:1 wt) with lithium tetrafluoroborate (LiBF₄) displayed a conductivity of 2.6 mS cm⁻¹ and no aluminum corrosion. In addition, it showed higher anodic stability on a Pt electrode than the standard electrolyte 1 M lithium hexafluorophosphate (LiPF₆) in EC:DEC (3:7 wt). Graphite/Li half cells using this electrolyte showed excellent rate capability up to 5C and good cycling stability (more than 98% capacity retention after 50 cycles at 1C). Additionally, the electrolyte was investigated in NCM/Li half cells. The cells were able to reach a capacity of 104 mAh g⁻¹ at 5C and capacity retention of more than 97% after 50 cycles. These results show that an electrolyte with a considerably increased flash point with respect to common electrolyte systems comprising linear carbonates, could be realized without any negative effects on the electrochemical performance in Li-half cells.     

Electrochemical properties of bare and Ta-substituted Nb2O5 nanostructures

In this work, bare and Ta-substituted Nb₂O₅ nanofibers are prepared by electrospinning followed by sintering at temperatures in the 800–1100 °C range for 1 h in air. Obtained bare and Ta-substituted Nb₂O₅ polymorphs are characterized by X-ray diffraction, scanning electron microscopy, density measurement, and Brunauer, Emmett and Teller surface area. Electrochemical properties are evaluated by cyclic voltammetry and galvanostatic techniques. Cycling performance of Nb₂O₅ structures prepared at temperature 800 °C, 900 °C, and 1100 °C shows following discharge capacity at the end of 10th cycle: 123, 140, and 164 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹ (1.5 C rate). Heat treated composite electrode based on M-Nb₂O₅ (1100 °C) in argon atmosphere at 220 °C, shows an improved discharge capacity of 192 (±3) mAh g⁻¹ at the end of 10th cycle. The discharge capacity of Ta-substituted Nb₂O₅ prepared at 900 °C and 1100 °C showed a reversible capacity of 150, 202 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹. Anodic electrochemical properties of M-Nb₂O₅ deliver a reversible capacity of 382 (±5) mAh g⁻¹ at the end of 25th cycle and Ta-substituted Nb₂O₅ prepared at 900 °C, 1000 °C and 1100 °C shows a reversible capacity of 205, 130 and 200 (±3) mAh g⁻¹ (at 25th cycle) in the range, 0.005–2.6 V, at current rate of 100 mA g⁻¹.     

Low temperature preparation of a high performance Pt/SWCNT counter electrode for flexible dye-sensitized solar cells

A platinum/single-wall carbon nanotube (Pt/SWCNT) film was sprayed onto a flexible indium-doped tin oxide coated polyethylene naphthalate (ITO/PEN) substrate to form a counter electrode for use in a flexible dye-sensitized solar cell using a vacuum thermal decomposition method at low temperature (120 °C). The obtained Pt/SWCNT electrode showed good chemical stability and light transmittance and had lower charge transfer resistance and higher electrocatalytic activity for the I₃⁻/I⁻ redox reaction compared to the flexible Pt electrode or a commercial Pt/Ti electrode. The light-to-electric energy conversion efficiency of the flexible DSSC based on the Pt/SWCNT/ITO/PEN counter electrode and the TiO₂/Ti photoanode reached 5.96% under irradiation with a simulated solar light intensity of 100 mW cm⁻². The efficiency was increased by 25.74% compared to the flexible DSSC with an unmodified Pt counter electrode.     

Synthesis of Pt nanocatalyst with micelle-encapsulated multi-walled carbon nanotubes as support for proton exchange membrane fuel cells

Micelle-encapsulated multi-walled carbon nanotubes (MWCNTs) with sodium dodecyl sulfate (SDS) were used as catalyst support to deposit platinum nanoparticles. High resolution transmission electron microscopy (HRTEM) images reveal the crystalline nature of Pt nanoparticles with a diameter of ∼4 nm on the surface of MWCNTs. A single proton exchange membrane fuel cell (PEMFC) with total catalyst loading of 0.2 mg Pt cm⁻² (anode 0.1 and cathode 0.1 mg Pt cm⁻², respectively) has been evaluated at 80 °C with H₂ and O₂ gases using Nafion-212 electrolyte. Pt/MWCNTs synthesized by using modified SDS-MWCNTs with high temperature treatment (250 °C) showed a peak power density of 950 mW cm⁻². Accelerated durability evaluation was carried out by conducting 1500 potential cycles between 0.1 and 1.2 V with 50 mV s⁻¹ scan rate, H₂/N₂ at 80 °C. The membrane electrode assembly (MEA) with Pt/MWCNTs showed superior performance stability with a power density degradation of only ∼30% compared to commercial Pt/C (70%) after potential cycles.     

Electrochemical investigation of LiMn2O4 cathodes in gel electrolyte at various temperatures

A composite lithium battery electrode of LiMn₂O₄ in combination with a gel electrolyte (1 M LiBF₄/24 wt% PMMA/1:1 EC:DEC) has been investigated by galvanostatic cycling experiments and electrochemical impedance spectroscopy (EIS) at various temperatures, i.e. −3<T<56 °C. For analysis of EIS data, a mathematical model taking into account local kinetics and potential distribution in the liquid phase within the porous electrode structure was used. Reasonable values of the double-layer capacitance, the exchange-current density and the solid phase diffusion were found as a function of temperature. The apparent activation energy of the charge-transfer (∼65 kJ mol⁻¹), the solid phase transfer (∼45 kJ mol⁻¹) and of the ionic bulk and effective conductance in the gel phase (∼34 kJ mol⁻¹), respectively, were also determined. The kinetic results related to ambient temperature were compared to those obtained in the corresponding liquid electrolyte. The incorporated PMMA was found to reduce the ionic conductivity of the free electrolyte, and it was concluded that the presence of 24 wt% PMMA does not have a significant influence on the kinetic properties of LiMn₂O₄.