A novel hierarchical Pt- and FTO-free counter electrode for dye-sensitized solar cell

A novel hierarchical Pt- and FTO-free counter electrode (CE) for the dye-sensitized solar cell (DSSC) was prepared by spin coating the mixture of TiO₂ nanoparticles and poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) solution onto the glass substrate. Compared with traditional Pt/FTO CE, the cost of the new CE is dramatically reduced by the application of bilayer TiO₂-PEDOT:PSS/PEDOT:PSS film and the glass substrate. The sheet resistance of this composite film is 35 Ω sq⁻¹ and is low enough to be used as an electrode. The surface morphologies of TiO₂-PEDOT:PSS layer and modified PEDOT:PSS layer were characterized by scanning electron microscope, which shows that the former had larger surface areas than the latter. Electrochemical impedance spectra and Tafel polarization curves prove that the catalytic activity of TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE is higher than that of PEDOT:PSS/FTO CE and is similar to Pt/FTO CE''s. This new fabricated device with TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE achieves a high power conversion efficiency (PCE) of 4.67%, reaching 91.39% of DSSC with Pt/FTO CE (5.11%).     

Nanocomposites of Bi5FeTi3O15 with MoS2 as novel Pt-free counter electrode in dye-sensitized solar cells

Bi₅FeTi₃O₁₅ (BFTO) nanofibers with diameters in the range of 40–100 nm have been fabricated by sol-gel based electrospinning technique. The structure and morphology of the nanofibers were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The MoS₂ nanoparticles are uniformly dispersed into the BFTO, forming nanocomposites. The optical bandgap of the nanocomposites decreases as MoS₂ content increases. The nanocomposites with different MoS₂ contents serve as low-cost counter electrodes (CEs) for dye-sensitized solar cells (DSSCs). Through photocurrent–voltage curves, electrochemical impedance spectroscopy and Tafel curves, the performance of the CEs indicates that the charge transfer resistance on the electrolyte-electrode interface lower and the catalytic activity for reduction of triiodide to iodide enhance with the increase of MoS₂ concentration. The DSSC with the CE exhibits a power conversion efficiency of 5.20% after the optimization of the content of MoS₂, which is almost 24 times larger than that of the pure BFTO CE.     

Electropolymerization of a poly(3,4-ethylenedioxythiophene) and functionalized, multi-walled, carbon nanotubes counter electrode for dye-sensitized solar cells and characterization of its performance

Composite films of poly(3,4-ethylenedioxythiophene) and functionalized, multi-walled, carbon nanotubes (PEDOT–MWCNT) were fabricated by a simple oxidative electropolymerization method. These films were formed on fluorine-doped, tin oxide, glass substrates as counter electrodes (CEs) of platinum-free, dye-sensitized solar cells (DSSCs). The surface morphology, formation mechanism and electrochemical nature of PEDOT–MWCNT films were investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), cyclic voltammetry (CV) and alternating current (AC) impedance spectroscopy. The SEM and AFM images showed that PEDOT–MWCNT films were more porous than PEDOT films. CV and AC impedance spectroscopy revealed that the PEDOT–MWCNT electrode had higher electrocatalytic activity for the I₃⁻/I⁻ redox reaction and a smaller charge transfer resistance than the PEDOT electrodes. The energy conversion efficiency of the DSSC with a PEDOT–MWCNT CE was 13.0% higher than with a PEDOT CE using the same conditions with a ruthenium sensitizer.     

A study of TiO2/carbon black composition as counter electrode materials for dye-sensitized solar cells

This study describes a systematic approach of TiO₂/carbon black nanoparticles with respect to the loading amount in order to optimize the catalytic ability of triiodide reduction for dye-sensitized solar cells. In particular, the cell using an optimized TiO₂ and carbon black electrode presents an energy conversion efficiency of 7.4% with a 5:1 ratio of a 40-nm TiO₂ to carbon black. Based on the electrochemical analysis, the charge-transfer resistance of the carbon counter electrode changed based on the carbon black powder content. Electrochemical impedance spectroscopy and cyclic voltammetry study show lower resistance compared to the Pt counter electrode. The obtained nanostructures and photo electrochemical study were characterized.     

Carbon nanotube counter electrode for high-efficient fibrous dye-sensitized solar cells

ABSTRACT: High-efficient fibrous dye-sensitized solar cell with carbon nanotube (CNT) thin films as counter electrodes has been reported. The CNT films were fabricated by coating CNT paste or spraying CNT suspension solution on Ti wires. A fluorine tin oxide-coated CNT underlayer was used to improve the adherence of the CNT layer on Ti substrate for sprayed samples. The charge transfer catalytic behavior of fibrous CNT/Ti counter electrodes to the iodide/triiodide redox pair was carefully studied by electrochemical impedance and current-voltage measurement. The catalytic activity can be enhanced by increasing the amount of CNT loading on substrate. Both the efficiencies of fibrous dye-sensitized solar cells using paste coated and sprayed CNT films as counter electrodes are comparative to that using Pt wires, indicating the feasibility of CNT/Ti wires as fibrous counter electrode for superseding Pt wires.     

Highly efficient bio-based porous carbon hybridized with tungsten carbide as counter electrode for dye-sensitized solar cell

Bio-based porous carbon (C_MA and C_TA) are successfully prepared from waste carton via microwave-assisted activation (MA) and two-step chemical activation (TA) methods, respectively. The as-prepared C_TA sample exhibits higher specific surface area (824.16 m² g⁻¹) and larger total pore volume (0.71 cm³ g⁻¹), as compared with those of the C_MA sample (655.36 m² g⁻¹ and 0.62 cm³ g⁻¹, correspondingly). The higher specific surface area could provide more catalytic sites; thus, the dye-sensitized solar cell (DSSC) assembled with a C_TA counter electrode (CE) deliver a power conversion efficiency (PCE) of 6.76%, surpass the C_MA-based DSSC (6.19%). Further, tungsten carbide (WC) are introduced into C_TA and C_MA to form hybrid catalysts (WC/C_TA and WC/C_MA, respectively) in order to improve their catalytic activities. Benefitting from the synergistic effect of bio-based porous carbon and WC, the DSSCs with WC/C_TA and WC/C_MA CEs exhibit superior PCE values of 7.32% and 6.85%, respectively, close to Pt (7.51%). This work provides an effective strategy for synthesizing low-cost and high-performance hybrid catalysts from bio-based carbon to achieve resource utilization of biomass waste in new energy fields.     

Stability study of carbon-based counter electrodes in dye-sensitized solar cells

This study describes a systematic investigation of the stability of a carbon/TiO₂ counter electrode for use in dye-sensitized solar cells (DSSCs). In this system, nanoparticle additives were introduced by adding Ti-hydrogel. The additives then bound carbon particles and enhanced the adhesion of carbon materials to the conductive substrate. After introducing the Ti-hydrogel into the carbon paste, the carbon/Ti-hydrogel composited counter electrode (HC-CE) showed a better conductivity and stability compared with that of the carbon counter electrode (C-CE), while the catalytic activity was not influenced. The device based on the HC-CE showed superior power conversion efficiency (6.3%) and long-term stability over the device based on the C-CE (5.8%).     

Selenization treatment on Ag8SnSxSe6-x counter electrode of dye-sensitized solar cells in improving its electron transfer and electrocatalytic activity

In this paper, Ag₈SnS₆ powder was synthesized by the one-pot method, then prepared into Ag₈SnS₆ and Selenization treated Ag₈SnS_xSe_6-x thin films. The effects brought by the amounts of added Se powder during the annealing process on the product phases, structures, and morphologies are characterized, and the electrochemical property and the cell efficiency as assembled into the counter electrode (CEs) for dye-sensitized solar cells (DSSCs) were investigated. It showed Se into the Ag₈SnS₆ lattice occupied the site of S to transform into Ag₈SnS_xSe_6-x. And the thin film also became unflatten since the particles became larger after Se doping. The cell efficiency of Ag₈SnS_xSe_6-x CEs reached 4.26%, which was increased by 28.31% compared to that of Ag₈SnS₆ CEs. Ag₈SnS_xSe_6-x CEs performed lower charge transfer resistance (Rct) and (△EPP), and an increased△E value between the conduction band level of CEs and the redox potential of electrolyte. After 10 cycles, the almost unchanged cathode/anode current density implied the Ag₈SnS_xSe_6-x CEs received good structure stability. Selenization treatment was able to facilitate electron transport and enhance the electrocatalytic activity, and as expected to be a promising method in improving the performance of the DSSCs.     

Electropolymerization kinetic study of 3,3-dimethyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine and its optical optimization for electrochromic window applications

Poly (3,3-dimethyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine), PProDOT-Me₂, is one of the most promising conducting polymers in the alkylenedioxythiophene based family for electrochromic window applications. In the electropolymerization kinetic study of 3,3-dimethyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepine (ProDOT-Me₂), microgravimetry and chronoamperometry were used to determine the reaction orders with respect to the electrolyte and monomer, and the corresponding general kinetic equation of electropolymerization. This study presents that monomer concentration has a strong impact on electropolymerization mechanism. The relationship between film thickness and polymerization time was analyzed indicating that saturation of polymerization reduced the increase rate of film thickness with polymerization time. Also, the electropolymerization conditions were optimized to reach high contrast (Δ%T > 70%) with the minimum of transmittance (%T_min < 1) for electrochromic window applications.     

Enhanced performance of a dye-sensitized solar cell with a modified poly(3,4-ethylenedioxythiophene)/TiO2/FTO counter electrode

ClO₄⁻-poly(3,4-ethylenedioxythiophene)/TiO₂/FTO (ClO₄⁻-PEDOT/TiO₂/FTO) counter electrode (CE) in dye-sensitized solar cells (DSSCs) is fabricated by using an electrochemical deposition method. Comparing with the DSSCs with ClO₄⁻-PEDOT/FTO counter electrode, the photocurrent-voltage (I-V) measurement reveals that the photocurrent conversion efficiency (η), fill factor (FF) and short-circuit current density (J_SC) of DSSCs with a ClO₄⁻-PEDOT/TiO₂/FTO CE increase. The enhanced performances of the DSSCs are attributed to the higher J_SC arising from the increase of active surface area of ClO₄⁻-PEDOT/TiO₂/FTO CE. Electrochemical impedance spectra (EIS) also indicate that the charge-transfer resistance on the ClO₄⁻-PEDOT/electrolyte interface decreases. Cyclic voltammetry results indicate that the ClO₄⁻-PEDOT/TiO₂/FTO electrode shows higher activity towards I₃⁻/I⁻ redox reaction than that of ClO₄⁻-PEDOT/FTO electrode.     

Al2O3-coated SnO2/TiO2 composite electrode for the dye-sensitized solar cell

A novel Al₂O₃-coated SnO₂/TiO₂ composite electrode has been applied to the dye-sensitized solar cell. In such an electrode, two kinds of energy barriers (SnO₂/TiO₂ and TiO₂/Al₂O₃) were designed to suppress the recombination processes of the photo-generated electrons and holes. After the SnO₂ was modified by colloid TiO₂, the photoelectric conversion efficiency of the SnO₂/TiO₂ composite cell increased to 2.08% by a factor of 2.8 comparing with that of the SnO₂ cell. The Al₂O₃ layer on the SnO₂/TiO₂ composite electrode further suppressed the generation of the dark current, resulting in 37% improvement in device performance comparing with the SnO₂/TiO₂ cell.     

The effect of transition metal ions (M2+=Mn2+, Ni2+, Co2+, Cu2+) on the chemical synthesis polyaniline as counter electrodes in dye-sensitized solar cells

The effect of transition metal ions(M~(2+)=Mn~(2+),Ni~(2+),Co~(2+),Cu~(2+)) on the chemical synthesis of polyaniline(PANI) used as a platinum-free counter electrode(CE) in dye-sensitized solar cells(DSSCs) was investigated.PANI was synthesized by co-polymerization of aniline in the presence of different transition metal ions by using potassium dichromate in acidic medium. It was found that the ion doping of PANI showed a certain catalytic activity for the regeneration of traditional iodide/triiodide(I~-/I_3~-) redox couples. The power conversion efficiency(η) of PANI CEs doped with Mn~(2+),Ni~(2+),Co~(2+) (4.41%, 2.36% and 2.10%, respectively) were higher than 1.94%, the value measured for PANI CE without doping. Doping with Cu~(2+)decreased the power conversion efficiency of PANI CE(PANI-Cu~(2+) η = 1.41%). The electrical properties of the PANI, PANI-Ni~(2+), PANI-Co~(2+),PANI-Mn~(2+) and PANI-Cu~(2+) were studied by cyclic voltammetry(CV), impedance(EIS), and Tafel polarization curve. The experimental results confirmed that PANI was affected by the doping of different transition metal ions(M~(2+)=Mn~(2+),Ni~(2+),Co~(2+),Cu~(2+)). These results indicate a potential application of ion doped PANI as counter electrode in cost-effective DSSCs.     

TiO2-B narrow nanobelt/TiO2 nanoparticle composite photoelectrode for dye-sensitized solar cells

In order to possess the merits of both building blocks, i.e. the rapid interfacial electron transport of TiO₂-B narrow nanobelts (NBs) and the high surface area of TiO₂ nanoparticles (NPs), the TiO₂-B NBs and TiO₂ NPs composites photoelectrodes were prepared with different weight ratios. The dye-sensitized solar cell prototypes were fabricated based on the composite photoelectrodes and the photoelectrical properties have been systematically studied. Although the amount of adsorption dye of composite solar cells decreased, the composite cells could obtain higher power conversion efficiency compared to pure TiO₂ NP solar cell by rational tuning the weight ratio of TiO₂-B NBs and TiO₂ NPs, which was due to the faster electron transfer rate. The dye adsorption amount and interfacial electron transport, which together determined the overall photoelectrical conversion efficiency, were investigated by the UV–vis spectra, the electrochemical impedance spectra (EIS), intensity-modulated photocurrent spectroscopy (IMPS) and intensity-modulated photovoltage spectroscopy (IMVS).     

A natural tomato slurry as a photosensitizer for dye-sensitized solar cells with TiO2/CuO composite thin films

We have studied the performance of dye-sensitized solar cells by employing natural dye “anthocyanins” extracted from the tomato slurry as a sensitizer for the TiO₂/CuO photoanode. The extracts were anchored on TiO₂/CuO films deposited on an ITO substrate which was used as a photoanode. The dye adsorbed TiO₂/CuO films electrode, the copper plate as a counter electrode, and iodolyte as an electrolyte were assembled into DSSCs. The conversion efficiency of the DSSCs was found to be 2.96% with a V_OC of 0.615 V, J_SC of 6.6 mA/cm², and an FF of 0.73. This work highlights the use of contribution of the tomato slurry as a natural sensitizer to enhance the efficiency of DSSCs.     

TiO2/modified natural clay semiconductor as a potential electrode for natural dye-sensitized solar cell

TiO₂/modified natural bentonite clay semiconductor, as a potential electrode of dye-sensitized solar cell, having a Ti:Si molar ratio of 85:15 was, for the first time, compared with pure TiO₂ (commercial P25) electrode in terms of solar cell efficiency and characteristics. 4-Chloro-2,5-difluorobenzoic acid and 4-(chloromethyl)benzoyl chloride were added to the electrodes to increase light harvesting ability of natural dyes extracted from red cabbage, rosella, and blue pea. The results showed that the TiO₂/clay semiconductor provided a higher surface area but a slightly lower efficiency than the pure TiO₂. The best natural sensitizer was found to be the dye extracted from red cabbage. Besides, the 4-(chloromethyl)benzoyl chloride provided a higher short circuit current for the TiO₂/clay semiconductor.     

TiO2 micro-flowers composed of nanotubes and their application to dye-sensitized solar cells

TiO₂ micro-flowers were made to bloom on Ti foil by the anodic oxidation of Ti-protruding dots with a cylindrical shape. Arrays of the Ti-protruding dots were prepared by photolithography, which consisted of coating the photoresists, attaching a patterned mask, illuminating with UV light, etching the Ti surface by reactive ion etching (RIE), and stripping the photoresist on the Ti foil. The procedure for the blooming of the TiO₂ micro-flowers was analyzed by field emission scanning electron microscopy (FESEM) as the anodizing time was increased. Photoelectrodes of dye-sensitized solar cells (DSCs) were fabricated using TiO₂ micro-flowers. Bare TiO₂ nanotube arrays were used for reference samples. The short-circuit current (J_sc) and the power conversion efficiency of the DSCs based on the TiO₂ micro-flowers were 4.340 mA/cm² and 1.517%, respectively. These values of DSCs based on TiO₂ micro-flowers were higher than those of bare samples. The TiO₂ micro-flowers had a larger surface area for dye adsorption compared to bare TiO₂ nanotube arrays, resulting in improved J_sc characteristics. The structure of the TiO₂ micro-flowers allowed it to adsorb dyes very effectively, also demonstrating the potential to achieve higher power conversion efficiency levels for DSCs compared to a bare TiO₂ nanotube array structure and the conventional TiO₂ nanoparticle structure.     

Effect of compressed TiO2 nanoparticle thin film thickness on the performance of dye-sensitized solar cells

In this study, dye-sensitized solar cells (DSSCs) were fabricated using nanocrystalline titanium dioxide (TiO₂) nanoparticles as photoanode. Photoanode thin films were prepared by doctor blading method with 420 kg/cm² of mechanical compression process and heat treatment in the air at 500°C for 30 min. The optimal thickness of the TiO₂ NP photoanode is 26.6 μm with an efficiency of 9.01% under AM 1.5G illumination at 100 mW/cm². The efficiency is around two times higher than that of conventional DSSCs with an uncompressed photoanode. The open-circuit voltage of DSSCs decreases as the thickness increases. One DSSC (sample D) has the highest conversion efficiency while it has the maximum short-circuit current density. The results indicate that the short-circuit current density is a compromise between two conflict factors: enlargement of the surface area by increasing photoanode thickness and extension of the electron diffusion length to the electrode as the thickness increases.     

Role of surface state on the electron flow in modified TiO2 film incorporating carbon powder for a dye-sensitized solar cell

An investigation of surface-related traps in nanostructured TiO₂ films modified by the incorporation of carbon powder was conducted by the potential-step chronoamperometric method. For the modification of the morphology and surface state of the nanoporous TiO₂ electrode, the incorporation of carbon into the white TiO₂ powder was accomplished. In the chronoamperometric data, all of the transients showed an initial fast phase (<1 s) followed by a slower phase which is related to the trap filling process. The trap-filling period of the carbon incorporated TiO₂ film becomes longer, as the applied negative potential increases, due to the widely distributed traps induced by the increased surface area. Furthermore, the film capacitance was derived as a function of the applied bias by integrating the current to time curves of the chronoamperometric data. The accumulated charge of the carbon incorporated TiO₂ film increases prominently in two regions. The dominant increase shown in the positive region (−0.7 to −0.9 V vs. Ag/AgCl at pH 13) of the flat band potential implies that the electron occupancy in the surface-related traps is increased. At a more negative potential (below −1.2 V vs. Ag/AgCl), electrons from the conduction band of the TiO₂ film substantially influence the total current, thereby inducing an exponential increase in the current. Therefore, it is found that most of the traps are located in the positive region of the flat band potential, since the Fermi level of the nanostructured TiO₂ film is positioned at −1.14 V vs. Ag/AgCl at pH 13. The trap sites in the sub-bandgap region of the TiO₂ film are important in the electron transport of photoinjected electrons from dye molecules and partially charge recombination with redox electrolyte in operating dye-sensitized solar cell. The influence of charge trap formed by increased surface states on the electron transport and electron transfer was investigated by photovoltage and photocurrent transient measurements.     

EIS analysis on low temperature fabrication of TiO2 porous films for dye-sensitized solar cells

A low temperature (<150 °C) fabrication method for preparation of TiO₂ porous films with high efficiency in dye-sensitized solar cells (DSSCs) has been developed. The Ti(IV) tetraisopropoxide (TTIP) was added to the paste of TiO₂ nanoparticles to interconnect the TiO₂ particles. The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance at the TiO₂/dye/electrolyte interface (R_ct2) and electron lifetime in the TiO₂ film (τ_e) under different molar ratios of TTIP/TiO₂ and also at various TiO₂ thicknesses. It was found that the R_ct2 decreased as the molar ratio increased from 0.02 to 0.08, however, it increased at a molar ratio of 0.2 due to the reduction in surface area for dye adsorption. In addition, the characteristic frequency peak shifted to lower frequency at a molar ratio of 0.08, indicating the longer electron lifetime. As for the thickness effect, TiO₂ film with a thickness around 17 μm achieved the best cell efficiency. EIS study also confirmed that, under illumination, the smallest R_ct2 was associated with a TiO₂ thickness of 17 μm, with the R_ct2 increased as the thickness of TiO₂ film increased. In the Bode plots, the characteristic frequency peaks shifted to higher frequency when the thickness of TiO₂ increased from 17.2 to 48.2 μm, indicating the electron recombination increases as the thickness of the TiO₂ electrode increases.Finally, to make better use of longer wavelength light, 30 wt% of larger TiO₂ particle (300 nm) was mixed with P25 TiO₂ as light scattering particles. It effectively increased the short-circuit current density and cell conversion efficiency from 7.44 to 8.80 mA cm⁻² and 3.75 to 4.20%, respectively.