Electrodeposited PbO2 thin film as positive electrode in PbO2/AC hybrid capacitor

Lead dioxide (PbO₂) thin films were prepared on Ti/SnO₂ substrates by means of electrodeposition method. Galvanostatic technique was applied in PbO₂ film formation process, and the effect of deposition current on morphology and crystalline form of the PbO₂ thin films was studied by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The energy storage capacity of the prepared PbO₂ electrode was investigated by means of cyclic voltammetry (CV) and charge/discharge cycles, and a rough surface structure PbO₂ film was selected as positive electrode in the construction of PbO₂/AC hybrid capacitor in a 1.28 g cm⁻³ H₂SO₄ solution. The electrochemical performance was determined by charge/discharge tests and electrochemical impedance spectroscopy (EIS). The results showed that the PbO₂/AC hybrid capacitor exhibited high capacitance, good cycling stability and long cycle life. In the voltage range of 1.8-0.8 V during discharge process, considering the weight of all components of the hybrid capacitor, including the two electrodes, current collectors, H₂SO₄ electrolyte and separator, the specific energy and power of the device were 11.7 Wh kg⁻¹ and 22 W kg⁻¹ at 0.75 mA cm⁻², and 7.8 Wh kg⁻¹ and 258 W kg⁻¹ at 10 mA cm⁻² discharge currents, respectively. The capacity retains 83% of its initial value after 3000 deep cycles at the 4 C rate of charge/discharge.     

Electrochemical investigation of LiNi0.5Mn1.5O4 thin film intercalation electrodes

This work provides kinetic and transport parameters of Li-ion during its extraction/insertion into thin film LiNi_0.5Mn_1.5O₄ free of binder and conductive additive. Thin films of LiNi_0.5Mn_1.5O₄ (0.2 μm thick) were prepared on electronically conductive gold substrate utilizing the electrostatic spray deposition technique. High purity LiNi_0.5Mn_1.5O₄ thin film electrodes were observed with cyclic voltammetry, to exhibit very sharp peaks, high reversibility, and absence of the 4 V signal related to the Mn³⁺/Mn⁴⁺ redox couple. The electrode subjected to 100 CV cycles of charge/discharge delivered a capacity of 155 mAh g⁻¹ on the first cycle and sustained a good cycling behavior while retaining 91% of the initial capacity after 50 cycles. Kinetics and mass-transport of Li-ion extraction at LiNi_0.5Mn_1.5O₄ thin film electrode were investigated by means of electrochemical impedance spectroscopy. The apparent chemical diffusion coefficient (D_app) value determined from EIS measurements changed depending on the electrode potential in the range of 10⁻¹⁰-10⁻¹² cm² s⁻¹. The D_app profile shows two minimums at the potential values close to the peak potentials of the corresponding cyclic voltammogram.     

Li diffusion in LiNi0.5Mn0.5O2 thin film electrodes prepared by pulsed laser deposition

Kinetic and transport parameters of Li ion during its extraction/insertion into thin film LiNi_0.5Mn_0.5O₂ free of binder and conductive additive were provided in this work. LiNi_0.5Mn_0.5O₂ thin film electrodes were grown on Au substrates by pulsed laser deposition (PLD) and post-annealed. The annealed films exhibit a pure layered phase with a high degree of crystallinity. Surface morphology and thin film thickness were investigated by field emission scanning electron microscopy (FESEM). The charge/discharge behavior and rate capability of the thin film electrodes were investigated on Li/LiNi_0.5Mn_0.5O₂ cells at different current densities. The kinetics of Li diffusion in these thin film electrodes were investigated by cyclic voltammetry (CV) and galvanostatic intermittent titration technique (GITT). CV was measured between 2.5 and 4.5 V at different scan rates from 0.1 to 2 mV/s. The apparent chemical diffusion coefficients of Li in the thin film electrode were calculated to be 3.13 × 10⁻¹³ cm²/s for Li intercalation and 7.44 × 10⁻¹⁴ cm²/s for Li deintercalation. The chemical diffusion coefficients of Li in the thin film electrode were determined to be in the range of 10⁻¹²-10⁻¹⁶ cm²/s at different cell potentials by GITT. It is found that the Li diffusivity is highly dependent on the cell potential.     

Electrochemical degradation of Ibuprofen on Ti/Pt/PbO2 and Si/BDD electrodes

The electrochemical oxidation of Ibuprofen (Ibu) was performed using a Ti/Pt/PbO₂ electrode as the anode, prepared according to literature, and a boron doped diamond (BDD) electrode, commercially available at Adamant Technologies. Tests were performed with model solutions of Ibu, with concentrations ranging from 0.22 to 1.75 mM for the Ti/Pt/PbO₂ electrode and 1.75 mM for the BDD electrode, using 0.035 M Na₂SO₄ as the electrolyte, in a batch cell, at different current densities (10, 20 and 30 mA cm⁻²). Absorbance measurements, Chemical Oxygen Demand (COD) and Total Organic Carbon (TOC) tests were conducted for all samples. The results have shown a very good degradation of Ibu, with COD removals between 60 and 95% and TOC removals varying from 48 to 92%, in 6 h experiments, with higher values obtained with the BDD electrode. General Current Efficiency and Mineralization Current Efficiency, determined for both electrodes, show a similar behaviour for 20 mA cm⁻² but a very different one at 30 mA cm⁻². The combustion efficiency was also determined for both anodes, and found to be slightly higher with BDD at lower current density and equal to 100% for both anodes at 30 mA cm⁻².     

TiO2 nanotubes manufactured by anodization of Ti thin films for on-chip Li-ion 2D microbatteries

The use of self-organized TiO₂ nanotube arrays electrochemically grown onto Si is investigated for the fabrication of an alternative electrode dedicated to on-chip Li-ion 2D microbatteries. Discharge/charge curves and cycling performance are studied in lithium-anode electrochemical test cells for both amorphous and crystalline titania nanotubes. At 5 μA cm⁻² amorphous TiO₂ nanotube layers onto Si deliver a maximum areal capacity of 89 μAh cm⁻² in the first reversible discharge and 56 μAh cm⁻² over 50 cycles. We demonstrate that these nanostructured thin film electrodes showing such electrochemical performances are compatible with IC technology.     

Electrochemical behavior of cysteine at a CuGeO3 nanowires modified glassy carbon electrode

A CuGeO₃ nanowire modified glassy carbon electrode was fabricated and characterized by scanning electron microscopy. The results of electrochemical impedance spectroscopy reveal that electron transfer through nanowire film is facile compared with that of bare glassy carbon electrode. The modified electrode exhibited a novel electrocatalytic behavior to the electrochemical reactions of l-cysteine in neutral solution, which was not reported previously. Two pairs of semi-reversible electrochemical peaks were observed and assigned to the processes of oxidation/reduction and adsorption/desorption of cysteine at the modified electrode, respectively. The electrochemical response of cysteine is poor in alkaline condition and is enhanced greatly in acidic solution, suggesting that hydrogen ions participate in the electrochemical oxidation process of cysteine. The intensities of two anodic peaks varied linearly with the concentration of cysteine in the range of 1 × 10⁻⁶ to 1 × 10⁻³ mol L⁻¹, which make it possible to sensitive detection of cysteine with the CuGeO₃ nanowire modified electrode. Furthermore, the modified electrode exhibited good reproducibility and stability.     

Structure and properties of PbO2-CeO2 anodes on stainless steel

The lack of ideal anodes with excellent activity and stability is one of the critical problems in electrochemical oxidation for organic wastewater treatment. It is reported in this paper that the PbO₂-CeO₂ films electrodeposited on stainless steel were used as catalytic electrodes for treating antibiotic wastewater. The PbO₂-CeO₂ films on stainless steel were proved to be high stability, good activity and relatively low cost. Because of these properties, the films are more attractive than any other electrocatalytic materials among conventional dimensionally stable anodes (DSA). Experimental results showed that the PbO₂-CeO₂ electrode has a service life of 1100 h in 3 M H₂SO₄ solution under a current density of 1 A cm⁻² at 35 °C, compared with 300 h for PbO₂ under the same conditions. The X-ray diffraction (XRD) patterns and SEM images indicated that the PbO₂-CeO₂ films on stainless steel have a dense structure and the preferred crystalline orientation on the substrate surface was changed. Color and chemical oxygen demand (COD) of antibiotics wastewater were studied by electrolysis by using these electrodes as anode and stainless steel as cathode. The results indicated that the anodes have excellent activity in antibiotic wastewater treatment. The PbO₂-CeO₂ electrodes have high chemical stability which contributed by the superstable nature of the electrode, dense microstructure, good conductivity and the improvement of bonding with the stainless steel during electrodeposition.     

Co3O4 thin film prepared by a chemical bath deposition for electrochemical capacitors

Co₃O₄ thin film is synthesized on ITO by a chemical bath deposition. The prepared Co₃O₄ thin film is characterized by X-ray diffraction, and scanning electron microscopy. Electrochemical capacitive behavior of synthesized Co₃O₄ thin film is investigated by cyclic voltammetry, constant current charge/discharge and electrochemical impedance spectroscopy. Scanning electron microscopy images show that Co₃O₄ thin film is composed of spherical-like coarse particles, together with some pores among particles. Electrochemical studies reveal that capacitive characteristic of Co₃O₄ thin film mainly results from pseudocapacitance. Co₃O₄ thin film exhibits a maximum specific capacitance of 227 F g⁻¹ at the specific current of 0.2 A g⁻¹. The specific capacitance reduces to 152 F g⁻¹ when the specific current increases to 1.4 A g⁻¹. The specific capacitance retention ratio is 67% at the specific current range from 0.2 to 1.4 A g⁻¹.     

Electrochemical incineration of chloranilic acid using Ti/IrO2, Pb/PbO2 and Si/BDD electrodes

The electrochemical oxidation of chloranilic acid (CAA) has been studied in acidic media at Pb/PbO₂, boron-doped diamond (Si/BDD) and Ti/IrO₂ electrodes by bulk electrolysis experiments under galvanostatic control. The obtained results have clearly shown that the electrode material is an important parameter for the optimization of such processes, deciding of their mechanism and of the oxidation products. It has been observed that the oxidation of CAA generates several intermediates eventually leading to its complete mineralization. Different current efficiencies were obtained at Pb/PbO₂ and BDD, depending on the applied current density in the range from 6.3 to 50 mA cm⁻². Also the effect of the temperature on Pb/PbO₂ and BDD electrodes was studied.UV spectrometric measurements were carried out at all anodic materials, with applied current density of 25 and 50 mA cm⁻². These results showed a faster CAA elimination at the BDD electrode. Finally, a mechanism for the electrochemical oxidation of CAA has been proposed according to the results obtained with the HPLC technique.     

Film thickness dependence of the dielectric properties of SrTiO3/BaTiO3 multilayer thin films deposited by double target RF magnetron sputtering

Four-layer SrTiO₃/BaTiO₃ thin films ((ST/BT)₄) with various thicknesses deposited on Pt/Ti/SiO₂/Si substrates at 500 °C by double target RF magnetron sputtering have been investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), profilometry, capacitance-voltage and current-voltage measurements. The XRD patterns reveal the frame formation of the sputter deposited (ST/BT)₄ with controlled modulation. The adhesion between the Pt bottom electrode layer and the BT layer is excellent. The dielectric constant of the (ST/BT)₄ multilayer thin film increases with increasing film thickness. The effects of temperature, frequency, and bias voltage on the dielectric constant of the (ST/BT)₄ multilayer thin films are discussed in detail. The leakage current density of the (ST/BT)₄ multilayer with a thickness of 450.0 nm is lower than 1.0 × 10⁻⁸ A/cm² for the applied voltage of less than 5 V, showing that the multilayer thin films with such a characteristic could be applied for use in dynamic random access memory (DRAMs) capacitors.     

Core–shell Ni0.5TiOPO4/C composites as anode materials in Li ion batteries

Pristine Ni_0.5TiOPO₄ was prepared via a traditional solid-state reaction, and then Ni_0.5TiOPO₄/C composites with core–shell nanostructures were synthesized by hydrothermally treating Ni_0.5TiOPO₄ in glucose solution. X-ray diffraction patterns indicate that Ni_0.5TiOPO₄/C crystallizes in monoclinic P2₁/c space group. Scanning electron microscopy and transmission electron microscopy show that the small particles with different sizes are coated with uniform carbon film of ∼3 nm in thickness. Raman spectroscopy also confirms the presence of carbon in the composites. Ni_0.5TiOPO₄/C composites presented a capacity of 276 mAh g⁻¹ after 30 cycles at the current density of 42.7 mA g⁻¹, much higher than that of pristine Ni_0.5TiOPO₄ (155 mAh g⁻¹). The improved electrochemical performances can be attributed to the existence of carbon shell.     

PTFE-F-PbO2 电极在H2SO4溶液中的析氧行为

F-PbO2 electrode and polytetrafluoroethylene （PTFE） doped F-PbO2 electrode （PTFE-F-PbO2） were prepared on a plexiglas sheet substrate by a series of procedure including chemical and electrochemical depositions. The electrochemical activities of these two electrodes for oxygen evolution （OE） reaction were examined by electrochemical tests. In comparison with F-PbO2, PTFE-F-PbO2 electrode exhibited larger active surface area and higher oxygen vacancy deficiency, which resulted in its higher electrocatalytic activity for OE. In addition, both exchange current density and activation energy of the electrodes for OE were calculated in terms of active surface area. The values of exchange current density and activation energy in 0.5 mol·L^-1 H2SO4 aqueous solution were 1.125×10^ -3 mA·cm^-2 and 18.62 kJ·mol^-1 for PTFE-F-PbO2, and 8.384×10^-4 mA·cm^- 2 and 28.98 kJ·mol^-1 for F-PbO2, respectively. Because these values are calculated on the basis of the active surface areas of the electrodes, the enhanced activity of PTFE-F-PbO2 can be attributed to an increase in oxygen vacancy deficiency of PbO2 due to doping by PTFE. The influence of PTFE adulteration on the activity of PbO2 film electrode for OE was investigated in detail in this study.     

LiCoO2 thin film cathode fabrication by rapid thermal annealing for micro power sources

The rapid thermal annealing (RTA) process was employed to obtain crystalline LiCoO₂ thin films. XRD analyses of the LiCoO₂ thin film show increased crystallinity with an increase in the RTA time. The Auger electron spectroscopic analysis of the LiCoO₂ film strongly suggests that the RTA process is more advantageous to obtain a stable inter layer between the substrate and the deposited film and between each deposited layer than the conventional annealing process. All-solid-state thin film cells composed of Li/lithium phosphorous oxynitride (Lipon)/LiCoO₂ systems were fabricated using the LiCoO₂ cathode treated with RTA. The optimum condition of RTA would be 900 s at 650 °C, which exhibited a good rate capability for high power applications. Two cells were connected in parallel to obtain a higher discharge current, and they showed a specific capacity of 38.4 μAh cm⁻² μm⁻¹ even at a 25C rate (current density: 7.96 mA cm⁻²).     

Synthesis and electrochemical performance of Li2FeSiO4/carbon/carbon nano-tubes for lithium ion battery

Li₂FeSiO₄/carbon/carbon nano-tubes (Li₂FeSiO₄/C/CNTs) and Li₂FeSiO₄/carbon (Li₂FeSiO₄/C) composites were synthesized by a traditional solid-state reaction method and characterized comparatively by X-ray diffraction, scanning electron microscopy, BET surface area measurement, galvanostatic charge-discharge and AC impedance spectroscopy, respectively. The results revealed that the Li₂FeSiO₄/C/CNT composite exhibited much better rate performance in comparison with the Li₂FeSiO₄/C composite. At 0.2 C, 5 C and 10 C, the former composite electrode delivered a discharge capacity of 142 mAh g⁻¹, 95 mAh g⁻¹, 80 mAh g⁻¹, respectively, and after 100 cycles at 1 C, the discharge capacity remained 95.1% of its initial value.     

Electrochemical stability of thin film LiMn2O4 cathode in organic electrolyte solutions with different compositions at 55 °C

A survey of the electrochemical stability of electrostatic spray deposited thin film of LiMn₂O₄ was performed in LiClO₄-EC-PC, LiBF₄-EC-PC, and LiPF₆-EC-PC solutions at 55 °C. The solution resistance, the surface film resistance, and the charge-transfer resistance were all found to depend on the electrolyte composition. Among the LiX-salts studied, the lowest charge transfer-resistance, and surface layer resistance were obtained in LiBF₄-EC-PC solution. There is no major influence of the electrolyte solution compositions upon lithium ion transport in the LiMn₂O₄ bulk at 55 °C. The diffusion coefficient of lithium in the solid phase varied within 10⁻¹⁰-10⁻⁸ cm² s⁻¹ in the three solutions. In general, it seems that in LiBF₄ solutions, the surface chemistry is the most stable in the three solutions examined, and hence the electrode impedance in LiBF₄ solutions was the lowest. In LiPF₆ solutions, HF seems to play an important role, and thus, the electrode impedance is relatively high due to the precipitation of surface LiF.     

Properties of nano-crystalline LiMn2O4 thin films deposited by pulsed laser deposition

Properties of LiMn₂O₄ thin films deposited on polished stainless steel substrates at 400 °C and 200 mTorr of oxygen by pulsed laser deposition have been characterized by electrochemical measurements and physical analyses. The film was mainly composed of nano-crystals less than 100 nm. A maximum specific capacity of 141.9 mAh/g cycled between 3.0 and 4.5 V with a current density of 20 μAh/cm² has been achieved. The film exhibited an excellent cycling stability up to 500 cycles. The low charge-transfer resistance at high potentials as revealed by AC impedance resulted in high charge/discharge potential and more capacity. The effect of overdischarge was limited and Jahn-Teller effect was overcome to a significant extent in this nano-crystalline film. Ex situ XRD, Raman and XPS provided supporting evidence in the changes in structure, reactivity and cycling stability of nano-crystalline LiMn₂O₄ film cathodes under different charge/discharge states and cycling tests. SEM images also revealed the stability of the surface topography after a long-term cycling test.     

Enhanced performance of a dye-sensitized solar cell with a modified poly(3,4-ethylenedioxythiophene)/TiO2/FTO counter electrode

ClO₄⁻-poly(3,4-ethylenedioxythiophene)/TiO₂/FTO (ClO₄⁻-PEDOT/TiO₂/FTO) counter electrode (CE) in dye-sensitized solar cells (DSSCs) is fabricated by using an electrochemical deposition method. Comparing with the DSSCs with ClO₄⁻-PEDOT/FTO counter electrode, the photocurrent-voltage (I-V) measurement reveals that the photocurrent conversion efficiency (η), fill factor (FF) and short-circuit current density (J_SC) of DSSCs with a ClO₄⁻-PEDOT/TiO₂/FTO CE increase. The enhanced performances of the DSSCs are attributed to the higher J_SC arising from the increase of active surface area of ClO₄⁻-PEDOT/TiO₂/FTO CE. Electrochemical impedance spectra (EIS) also indicate that the charge-transfer resistance on the ClO₄⁻-PEDOT/electrolyte interface decreases. Cyclic voltammetry results indicate that the ClO₄⁻-PEDOT/TiO₂/FTO electrode shows higher activity towards I₃⁻/I⁻ redox reaction than that of ClO₄⁻-PEDOT/FTO electrode.     

Electrochemical performance of single crystalline spinel LiMn2O4 nanowires in an aqueous LiNO3 solution

Single crystalline cubic spinel LiMn₂O₄ nanowires were synthesized by hydrothermal method and the precursor calcinations. The phase structures and morphologies were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and high-resolution transmission electron microscopy (HRTEM). Galvanostatic charging/discharging cycles of as-prepared LiMn₂O₄ nanowires were performed in an aqueous LiNO₃ solution. The initial discharge capacity of LiMn₂O₄ nanowires was 110 mAh g⁻¹, and the discharge capacity was still above 100 mAh g⁻¹ after 56 cycles at 10C-rate, and then 72 mAh g⁻¹ was registered after 130 cycles. This is the first report of a successful use of single crystalline spinel LiMn₂O₄ nanowire as cathode material for the aqueous rechargeable lithium battery (ARLB).     

Electrochemical degradation of azo dye C.I. Reactive Red 195 by anodic oxidation on Ti/SnO2-Sb/PbO2 electrodes

This study investigated the electrochemical degradation of C.I. Reactive Red 195 (RR195) in aqueous solution on a Ti/SnO₂-Sb/PbO₂ electrode. The influence of operating variables on the mineralization efficiency was studied as a function of the current density, the initial pH, the initial concentration of the dye and the addition of NaCl. The efficiency of RR195 mineralization decreased with increased initial concentration, from 100 mg L⁻¹ to 400 mg L⁻¹. The current density had both a positive and a negative effect on degradation rates, and no significant effect of initial pH on RR195 mineralization was observed. Measurement of absorbance was used to discriminate the effect of NaCl in the electro-oxidation process. We found that the decolouring efficiency increased whereas the mineralization efficiency decreased with the increasing concentration of NaCl. The intermediates formed during the degradation were detected by gas chromatography-mass spectrometry, and the major aromatic intermediates identified were 1-(3,6,8-trihydroxy-1-naphthyl)urea, nitrobenzene, benzo-1,4-quinone, (3,6,8-trihydroxy-1-naphthyl)carbamic acid and phthalic acid. Quantitative measurement of organic and inorganic ions was done by ion chromatography. On the basis of the reaction products identified, a possible degradation pathway for the anodic oxidation of RR195 in aqueous solution is proposed.     

A large capacity of LiV3O8 cathode material for rechargeable lithium-based batteries

A cathode material, LiV₃O₈, for rechargeable lithium-based batteries has been prepared via a combined freeze-drying method and appropriately post-treated in argon atmosphere. It was found that the sample post-treated at 300 °C in Ar has the optimal performance. Electrochemical tests performed on this material demonstrated its very high insertion capacity of 347 mAh g⁻¹ (3.7 Li⁺ per LiV₃O₈) at a current density of 50 mA g⁻¹ (C/6). Most important is that it displayed an excellent cycling stability and after 60 cycles, a discharge capacity with 351 mAh g⁻¹ was obtained. It was proposed that a short-range crystallographic order had a stronger influence on the electrochemical performance of an electrode material in this work, instead of the surface area, particle size and crystalline degree, etc.