Synthesis of highly crystalline spinel LiMn2O4 by a soft chemical route and its electrochemical performance

Highly crystalline spinel LiMn₂O₄ was successfully synthesized by annealing lithiated MnO₂ at a relative low temperature of 600 °C, in which the lithiated MnO₂ was prepared by chemical lithiation of the electrolytic manganese dioxide (EMD) and LiI. The LiI/MnO₂ ratio and the annealing temperature were optimized to obtain the pure phase LiMn₂O₄. With the LiI/MnO₂ molar ratio of 0.75, and annealing temperature of 600 °C, the resulting compounds showed a high initial discharge capacity of 127 mAh g⁻¹ at a current rate of 40 mAh g⁻¹. Moreover, it exhibited excellent cycling and high rate capability, maintaining 90% of its initial capacity after 100 charge-discharge cycles, at a discharge rate of 5 C, it kept more than 85% of the reversible capacity compared with that of 0.1 C.     

Synthesis of spinel LiMn2O4 with manganese carbonate prepared by micro-emulsion method

Micro-spherical particle of MnCO₃ has been successfully synthesized in CTAB-C₈H₁₈-C₄H₉OH-H₂O micro-emulsion system. Mn₂O₃ decomposed from the MnCO₃ is mixed with Li₂CO₃ and sintered at 800 °C for 12 h, and the pure spinel LiMn₂O₄ in sub-micrometer size is obtained. The LiMn₂O₄ has initial discharge specific capacity of 124 mAh g⁻¹ at discharge current of 120 mA g⁻¹ between 3 and 4.2 V, and retains 118 mAh g⁻¹ after 110 cycles. High-rate capability test shows that even at a current density of 16 C, capacity about 103 mAh g⁻¹ is delivered, whose power is 57 times of that at 0.2 C. The capacity loss rate at 55 °C is 0.27% per cycle.     

Preparation and characterization of core–shell structure Fe3O4/C nanoparticles with unique stability and high electrochemical performance for lithium-ion battery anode material

Core–shell structure carbon coating Fe₃O₄ nanoparticles are prepared by a two-step method. The crystalline structure and the electrochemical performance of the prepared samples are investigated. The results indicate that a uniform and continuous carbon layer is formed on the surface of Fe₃O₄ nanoparticles. The core–shell structure Fe₃O₄/C nanoparticles show a high initial discharge capacity of 1546 mAh g⁻¹ and a specific stable discharge capacity of about 800 mAh g⁻¹ at 0.5 C with no noticeable capacity fading up to 100 cycles.     

Electrochemical properties of bare and Ta-substituted Nb2O5 nanostructures

In this work, bare and Ta-substituted Nb₂O₅ nanofibers are prepared by electrospinning followed by sintering at temperatures in the 800–1100 °C range for 1 h in air. Obtained bare and Ta-substituted Nb₂O₅ polymorphs are characterized by X-ray diffraction, scanning electron microscopy, density measurement, and Brunauer, Emmett and Teller surface area. Electrochemical properties are evaluated by cyclic voltammetry and galvanostatic techniques. Cycling performance of Nb₂O₅ structures prepared at temperature 800 °C, 900 °C, and 1100 °C shows following discharge capacity at the end of 10th cycle: 123, 140, and 164 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹ (1.5 C rate). Heat treated composite electrode based on M-Nb₂O₅ (1100 °C) in argon atmosphere at 220 °C, shows an improved discharge capacity of 192 (±3) mAh g⁻¹ at the end of 10th cycle. The discharge capacity of Ta-substituted Nb₂O₅ prepared at 900 °C and 1100 °C showed a reversible capacity of 150, 202 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹. Anodic electrochemical properties of M-Nb₂O₅ deliver a reversible capacity of 382 (±5) mAh g⁻¹ at the end of 25th cycle and Ta-substituted Nb₂O₅ prepared at 900 °C, 1000 °C and 1100 °C shows a reversible capacity of 205, 130 and 200 (±3) mAh g⁻¹ (at 25th cycle) in the range, 0.005–2.6 V, at current rate of 100 mA g⁻¹.     

Hydrothermal synthesis of LiMn2O4/C composite as a cathode for rechargeable lithium-ion battery with excellent rate capability

A spinel LiMn₂O₄/C composite was synthesized by hydrothermally treating a precursor of manganese oxide/carbon (MO/C) composite in 0.1 M LiOH solution at 180 °C for 24 h, where the precursor was prepared by reducing potassium permanganate with acetylene black (AB). The AB in the precursor serves as the reducing agent to synthesize the LiMn₂O₄ during the hydrothermal process; the excess of AB remains in the hydrothermal product, forming the LiMn₂O₄/C composite, where the remaining AB helps to improve the electronic conductivity of the composite. The contact between LiMn₂O₄ and C in our composite is better than that in the physically mixed LiMn₂O₄/C material. The electrochemical performance of the LiMn₂O₄/C composite was investigated; the material delivered a high capacity of 83 mAh g⁻¹ and remained 92% of its initial capacity after 200 cycles at a current density of 2 A g⁻¹, indicating its excellent rate capability as well as good cyclic performance.     

Ultrasonic spray pyrolysis of nano crystalline spinel LiMn2O4 showing good cycling performance in the 3 V range

Spherical lithium manganese oxide spinel was synthesized by an ultrasonic spray pyrolysis method, and has been characterized using X-ray diffraction, scanning electron microscopy, transimission electron microscopy and electrochemical cycling at 3 V regions. The LiMn₂O₄ powders were composed of about 10 nm-sized primary particles. The delivered discharge capacity of the synthesized nano-material was 125 mAh g⁻¹ between 2.4 and 3.5 V and its retention was about 96% upon 50 cycling. From the high resolution transmission electron microscopic study, it was found that structural transition of the parent material did not occur even after the 50th electrochemical cycling on the 3 V region. It seems that the reversible structural change is possible for nanocrystalline LiMn₂O₄ as observed by the X-ray diffraction and transition electron microscopic observations.     

Electrochemical and ex situ XRD studies of a LiMn1.5Ni0.5O4 high-voltage cathode material

Sub-micro spinel-structured LiMn_1.5Ni_0.5O₄ material was prepared by a spray-drying method. The electrochemical properties of LiMn_1.5Ni_0.5O₄ were investigated using Li ion model cells, Li/LiPF₆ (EC + DMC)/LiMn_1.5Ni_0.5O₄. It was found that the first reversible capacity was about 132 mAh g⁻¹ in the voltage range of 3.60-4.95 V. Ex situ X-ray diffraction (XRD) analysis had been used to characterize the first charge/discharge process of the LiMn_1.5Ni_0.5O₄ electrode. The result suggested that the material configuration maintained invariability. At room temperature, on cycling in high-voltage range (4.50-4.95 V) and low-voltage range (3.60-4.50 V), the discharge capacity of the material was about 100 and 25 mAh g⁻¹, respectively, and the spinel LiMn_1.5Ni_0.5O₄ exhibited good cycle ability in both voltage ranges. However, at high temperature, the material showed different electrochemical characteristics. Excellent electrochemical performance and low material cost make this spinel compound an attractive cathode for advanced lithium ion batteries.     

Synthesis and electrochemical properties of LiAl0.05Mn1.95O4 by the ultrasonic assisted rheological phase method

Pure-phase and well-crystallized spinel LiAl_0.05Mn_1.95O₄ powders were successfully synthesized by a simple ultrasonic assisted rheological phase (UARP) method. The structure and morphology properties of this as-prepared powder compared with the pristine LiMn₂O₄ and LiAl_0.05Mn_1.95O₄ obtained from the solid-state reaction (SSR) method were investigated by powder X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical properties focused on the LiAl_0.05Mn_1.95O₄ by this new method have also been investigated in detail. According to these tests results, it is obviously to see that the newly prepared sample delivers a relatively high initial discharge capacity of 111.6 mAh g⁻¹, presents excellent rate capability and reversibility, and shows good cycling stability with capacity retention of 90.6% after 70 cycles. Meanwhile, the electrochemical impedance spectroscopy (EIS) investigations were employed to study the electrochemical process of Li⁺ ions with the synthesized LiAl_0.05Mn_1.95O₄ electrode in detail.     

A large capacity of LiV3O8 cathode material for rechargeable lithium-based batteries

A cathode material, LiV₃O₈, for rechargeable lithium-based batteries has been prepared via a combined freeze-drying method and appropriately post-treated in argon atmosphere. It was found that the sample post-treated at 300 °C in Ar has the optimal performance. Electrochemical tests performed on this material demonstrated its very high insertion capacity of 347 mAh g⁻¹ (3.7 Li⁺ per LiV₃O₈) at a current density of 50 mA g⁻¹ (C/6). Most important is that it displayed an excellent cycling stability and after 60 cycles, a discharge capacity with 351 mAh g⁻¹ was obtained. It was proposed that a short-range crystallographic order had a stronger influence on the electrochemical performance of an electrode material in this work, instead of the surface area, particle size and crystalline degree, etc.     

Synthesis of spherical spinel LiMn2O4 with commercial manganese carbonate

Spherical spinel LiMn₂O₄ particles were successfully synthesized from a mixture of manganese compounds containing commercial manganese carbonate by sintering of the spray-dried precursor. Different preparation routes were investigated to improve the tap density and to enhance the electrochemical performance of LiMn₂O₄. The structure and morphology of the LiMn₂O₄ particles were confirmed by X-ray diffraction (XRD) and scanning electron microscopy. The results showed that hollow spherical LiMn₂O₄ particles could be obtained when only commercial MnCO₃ was used as the manganese source. These particles had a low tap density (ca.0.8 g/cm³). Perfect micron-sized spherical LiMn₂O₄ particles with good electrochemical performance were obtained by spray-drying a slurry composed of MnCO₃, Mn(CH₃CHOO)₂ and LiOH, followed by a dynamic sintering process and a stationary sintering process. The as-prepared spherical LiMn₂O₄ particles comprised hundreds of nanosize crystal grains and had a high tap density(ca. 1.4 g/cm³). The galvanostatic charge-discharge measurements indicated that the spherical LiMn₂O₄ particles had an initial capacity of 121 mAh/g between 3.0 and 4.2 V at 0.2 C rate and still delivered a reversible capacity of 112 mAh/g at 2 C rate. The retention of capacity after 50 cycles was still 96% of its initial capacity at 0.2 C. All the results showed that the as-prepared spherical LiMn₂O₄ particles had an excellent electrochemical performances. The methods we used for preparing spherical LiMn₂O₄ are energy-saving and suitable for industrial application.     

High capacity ZnFe2O4 anode material for lithium ion batteries

A nanostructured ternary transition metal oxide, ZnFe₂O₄, is synthesized via the simple polymer pyrolysis method. The characteristics of the material are examined by thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The electrochemical test results show that this method of ZnFe₂O₄ synthesis produces high specific capacities and good cycling performance, with an initial specific capacity as high as 1419.6 mAh g⁻¹ at first discharge that is maintained at over 800 mAh g⁻¹ even after 50 charge–discharge cycles. The electrode also presents a good rate capability, with a high rate of 4C (1C = 928 mA g⁻¹), a reversible specific capacity that can be as high as 400 mAh g⁻¹. ZnFe₂O₄ is a potential alternative to high-performance nanostructured anode material in lithium ion batteries.     

Effects of carbon source and carbon content on electrochemical performances of Li4Ti5O12/C prepared by one-step solid-state reaction

Li₄Ti₅O₁₂/C composites were synthesized by one-step solid-state reaction method using four commonly used organic compounds or organic polymers as carbon source, i.e., polyacrylate acid (PAA), citric acid (CA), maleic acid (MA) and polyvinyl alcohol (PVA). The physical characteristics of Li₄Ti₅O₁₂/C composites were investigated by X-ray diffraction, electron microscopy, Raman spectroscopy, particle size distribution and thermogravimetry-derivative thermogravimetry techniques. Their electrochemical properties were characterized by cyclic voltammograms, electrochemical impedance spectra, constant current charge–discharge and rate charge–discharge. These analyses indicated that the carbon source and carbon content have a great effect on the physical and electrochemical performances of Li₄Ti₅O₁₂/C composites. An ideal carbon source and appropriate carbon content effectively improved the electrical contact between the Li₄Ti₅O₁₂ particles, which enhanced the discharge capacity and rate capability of Li₄Ti₅O₁₂/C composites. PAA was the best carbon source for the synthesis of Li₄Ti₅O₁₂/C composites. When the carbon content was 3.49 wt.% (LiOH·H₂O/PAA molar ratio of 1), as-prepared Li₄Ti₅O₁₂/C showed the maximum discharge capacity. At 0.2 C, initial capacity of the optimized sample was 168.6 mAh g⁻¹ with capacity loss of 2.8% after 50 cycles. At 8 and 10 C, it showed discharge capacities of 143.5 and 132.7 mAh g⁻¹, with capacity loss of 8.7 and 9.9% after 50 cycles, respectively.     

Enhanced electrochemical performances of LiNi0.5Mn1.5O4 spinel via ethylene glycol-assisted synthesis

A simple and effective method, ethylene glycol-assisted co-precipitation method, has been employed to synthesize LiNi_0.5Mn_1.5O₄ spinel. As a chelating agent, ethylene glycol can realize the homogenous distributions of metal ions at the atomic scale and prevent the growth of LiNi_0.5Mn_1.5O₄ particles. XRD reveals that the prepared material is a pure-phase cubic spinel structure (Fd3m) without any impurities. SEM images show that it has an agglomerate structure with the primary particle size of less than 100 nm. Electrochemical tests demonstrate that the as-prepared LiNi_0.5Mn_1.5O₄ possesses high capacity and excellent rate capability. At 0.1 C rate, it shows a discharge capacity of 137 mAh g⁻¹ which is about 93.4% of the theoretical capacity (146.7 mAh g⁻¹). At the high rate of 5 C, it can still deliver a discharge capacity of 117 mAh g⁻¹ with excellent capacity retention rate of more than 95% after 50 cycles. These results show that the as-prepared LiNi_0.5Mn_1.5O₄ is a promising cathode material for high power Li-ion batteries.     

High power performance of nano-LiFePO4/C cathode material synthesized via lauric acid-assisted solid-state reaction

A nano-LiFePO₄/C composite has been directly synthesized from micrometer-sized Li₂CO₃, NH₄H₂PO₄, and FeC₂O₄·2H₂O by the lauric acid-assisted solid-state reaction method. The SEM and TEM observations demonstrate that the synthesized nano-LiFePO₄/C composite has well-dispersed particles with a size of about 100–200 nm and an in situ carbon layer with thickness of about 2 nm. The prepared nano-LiFePO₄/C composite has superior rate capability, delivering a discharge capacity of 141.2 mAh g⁻¹ at 5 °C, 130.9 mAh g⁻¹ at 10 C, 121.7 mAh g⁻¹ at 20 °C, and 112.4 mAh g⁻¹ at 30 °C. At −20 °C, this cathode material still exhibits good rate capability with a discharge capacity of 91.9 mAh g⁻¹ at 1 °C. The nano-LiFePO₄/C composite also shows excellent cycling ability with good capacity retention, up to 100 cycles at a high current density of 30 °C. Furthermore, the effect of lauric acid in the preparation of nano-LiFePO₄/C composite was investigated by comparing it with that of citric acid. The SEM images reveal that the morphology of the LiFePO₄/C composite transformed from the porous structure to fine particles as the molar ratio of lauric acid/citric acid increased.     

Enhanced cycling stability of LiMn2O4 cathode by amorphous FePO4 coating

The cycling performance of LiMn₂O₄ at room and elevated temperatures is improved by FePO₄ modification through chemical deposition method. The pristine and FePO₄-coated LiMn₂O₄ materials are characterized by X-ray diffraction, Raman spectroscopy, scanning electron microscopy and transmission electron microscopy. Their cycling performances are thoroughly investigated and compared. The 3 wt.% FePO₄-coated LiMn₂O₄ exhibits capacity losses of only 32% and 34% at room temperature and 55 °C, respectively, after 80 cycles, much better than those of the pristine material, 55% and 72%. The cyclic voltammograms at 55 °C reveal that the improvement in the cycling performance of FePO₄-coated LiMn₂O₄ electrodes can be attributed to the stabilization of spinel structures. The separation of FePO₄ between active materials and electrolyte and its interaction with SEI (solid electrolyte interphase) film are believed to account for the improved performances.     

Enhanced rate performance of carbon-coated LiNi0.5Mn1.5O4 cathode material for lithium ion batteries

Conductive carbon has been coated on the surface of LiNi_0.5Mn_1.5O₄ cathode material by the carbonization of sucrose for the purpose of improving the rate performance. The effect of carbon coating on the physical and electrochemical properties is discussed through the characterizations of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), cycling and rate tests. Results demonstrate that the carbon coating can greatly enhance the discharge capacity, rate capability and cycling stability of the LiNi_0.5Mn_1.5O₄ without degrading the spinel structure. The sample modified with 1 wt.% sucrose displays the best performance. A large capacity of 130 mAh g⁻¹ at 1 C discharge rate with a high retention of 92% after 100 cycles and a stable 114 mAh g⁻¹ at 5 C discharge rate can be delivered. The remarkably improved rate properties of the carbon-coated samples are due to the suppression of the solid electrolyte interfacial (SEI) layer development and faster kinetics of both the Li⁺ diffusion and the charge transfer reaction.     

Synthesis and electrochemical characterization of nano-CeO2-coated nanostructure LiMn2O4 cathode materials for rechargeable lithium batteries

LiMn₂O₄ spinel cathode materials were coated with 0.5, 1.0, and 1.5 wt.% CeO₂ by a polymeric process, followed by calcination at 850 °C for 6 h in air. The surface-coated LiMn₂O₄ cathode materials were physically characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron microscopy (XPS). XRD patterns of CeO₂-coated LiMn₂O₄ revealed that the coating did not affect the crystal structure or the Fd3m space group of the cathode materials compared to uncoated LiMn₂O₄. The surface morphology and particle agglomeration were investigated using SEM, TEM image showed a compact coating layer on the surface of the core materials that had average thickness of about 20 nm. The XPS data illustrated that the CeO₂ completely coated the surface of the LiMn₂O₄ core cathode materials. The galvanostatic charge and discharge of the uncoated and CeO₂-coated LiMn₂O₄ cathode materials were measured in the potential range of 3.0-4.5 V (0.5 C rate) at 30 °C and 60 °C. Among them, the 1.0 wt.% of CeO₂-coated spinel LiMn₂O₄ cathode satisfies the structural stability, high reversible capacity and excellent electrochemical performances of rechargeable lithium batteries.     

Core–shell Ni0.5TiOPO4/C composites as anode materials in Li ion batteries

Pristine Ni_0.5TiOPO₄ was prepared via a traditional solid-state reaction, and then Ni_0.5TiOPO₄/C composites with core–shell nanostructures were synthesized by hydrothermally treating Ni_0.5TiOPO₄ in glucose solution. X-ray diffraction patterns indicate that Ni_0.5TiOPO₄/C crystallizes in monoclinic P2₁/c space group. Scanning electron microscopy and transmission electron microscopy show that the small particles with different sizes are coated with uniform carbon film of ∼3 nm in thickness. Raman spectroscopy also confirms the presence of carbon in the composites. Ni_0.5TiOPO₄/C composites presented a capacity of 276 mAh g⁻¹ after 30 cycles at the current density of 42.7 mA g⁻¹, much higher than that of pristine Ni_0.5TiOPO₄ (155 mAh g⁻¹). The improved electrochemical performances can be attributed to the existence of carbon shell.     

Electrochemical properties of TiP2O7 and LiTi2(PO4)3 as anode material for lithium ion battery with aqueous solution electrolyte

Some polyanionic compounds, e.g. TiP₂O₇ and LiTi₂(PO₄)₃ with 3D framework structure were proposed to be used as anodes of lithium ion battery with aqueous electrolyte. The cyclic voltammetry properties TiP₂O₇ and LiTi₂(PO₄)₃ suggested that Li-ion de/intercalation reaction can occur without serious hydrogen evolution in 5 M LiNO₃ aqueous solution. The TiP₂O₇ and LiTi₂(PO₄)₃ give capacities of about 80 mAh/g between potentials of −0.50 V and 0 V (versus SHE) and 90 mAh/g between −0.65 V and −0.10 V (versus SHE), respectively. A test cell consisting of TiP₂O₇/5 M LiNO₃/LiMn₂O₄ delivers approximately 42 mAh/g (weight of cathode and anode) at average voltage of 1.40 V, and LiTi₂(PO₄)₃/5 M LiNO₃/LiMn₂O₄ delivers approximately 45 mAh/g at average voltage of 1.50 V. Both as-assembled cells suffered from short cycle life. The capacity fading may be related to deterioration of anode material.     

Electrochemical properties of nanostructured Li1.2V3O8 in aqueous LiNO3 solution

The amorphous hydrated precursor of Li_1.2V₃O₈ was synthesized by soft chemistry method, and then heat-treated in air at several temperatures within the range 200–400 °C. The heat-treatment changed its morphological, structural and charging/discharging performance. The product obtained upon the treatment at 300 °C, consisting of uniform, rod-shaped particles, 100–150 nm in diameter and 300–800 nm in length, displayed the best electrochemical performance in aqueous LiNO₃ solution. Its initial discharge capacity amounted to 136.8 mAh g⁻¹ at a rate of C/5, which upon 50 charging/discharging cycles decreased for only 12%.