Pt／TiO2纳米粒子的制备及其光催化性能研究

采用溶胶-凝胶法制备了掺杂Pt的TiO2粉末，利用紫外可见光谱对粉末的光吸收性能进行了表征，并分别在模拟日光和可见光下考察了其光催化氧化对．硝基苯酚的活性。结果表明，掺杂Pt以后TiO2粉末的光谱吸收范围被拓展至可见光，光催化活性也明显提高。在模拟日光照射下，以光催化活性较好的Pt／TiO2粉末为催化剂降解对．硝基苯酚，4h后对-硝基苯酚的转化率为93．7％，其反应是一级反应。     

具有可见光活性的TiO2薄膜的制备及光催化性能

运用磁控溅射技术在浸渍－提拉法制得的TiO2薄膜上溅射三氧化钨层得到光催化薄膜。采用SEM、XRD、AES、UV－vis漫反射光谱等方法表征催化剂薄膜的厚度、晶相结构、化学元素组成及光吸收性能。以甲基橙的光催化降解为反应模型，高压汞灯为光源，溅射有三氧化钨薄膜的光催化活性低于纯TiO2薄膜；滤过紫外光后，溅射有三化钨的薄膜光催化活性明显高于纯TiO2薄膜。本实验提供了一种制备高可见光活性的TiO2薄膜的方法。     

Pt/TiO_2纳米薄膜的制备及光催化气相甲醇制氢的研究

通过溶胶-凝胶法制备了Pt/TiO2纳米薄膜,并在气相连续流动装置中,对甲醇的光催化脱氢反应进行了研究。将Pt/TiO2薄膜催化剂与TiO2薄膜催化剂的光催化活性进行了比较,考察了产氢量甲醇浓度、光照时间的关系,以及空速、反应温度对甲醇转化率的影响。结果表明,经过还原后分散于TiO2薄膜表面的Pt是以Pt2+及Pt0价态存在的。Pt/TiO2纳米薄膜是未负载Pt的纳米薄膜光催化活性的28倍。增加甲醇蒸汽的浓度会使产氢速率增大;当甲醇浓度在29%时,产氢速率达到最大,为4.68mmol/h。醇的转化率随着空速的增加而减小。该反应在一定的浓度范围内是一级反应,其反应的活化能为26.19kJ/mol。     

Pt/Fe_2O_3/TiO_2的制备、表征及其光催化活性研究

报道了担载不同贵金属或过渡金属氧化物的TiO2 催化剂对空气中微量甲醛的光催化氧化的研究结果。实验发现 ,TiO2 上担载Fe2 O3 或Pt时对甲醛均有较高的光催化氧化活性。同时担载双组分的光催化剂Pt Fe2 O3 TiO2 ,由于 2种组分的协同作用 ,具有更高的光催化活性。研究了催化剂制备因素、催化剂的结构及表面特性对催化活性的影响     

Pt/Fe2O3/TiO2的制备、表征及其光催化活性研究

报道了担载不同贵金属或过渡金属氧化物的TiO2催化剂对空气中微量甲醛的光催化氧化的研究结果.实验发现,TiO2上担载Fe2O3或Pt时对甲醛均有较高的光催化氧化活性.同时担载双组分的光催化剂Pt/Fe2O3/TiO2,由于2种组分的协同作用,具有更高的光催化活性.研究了催化剂制备因素、催化剂的结构及表面特性对催化活性的影响.     

Pt／Fe2O3／TiO2的制备、表征及其光催化活性研究

报道了担载不同贵金属或过渡金属氧化物的TiO2催化剂对空气中微量甲醛的光催化氧化的研究结果,实验发现,TiO2上担载Fe2O3或Pt时对甲醛均有较高的光催化氧化活性,同时担载双组分的光催化剂Pt/Fe2O3/TiO2,由于2种组分的协同作用,上仍更高的光催化活性,研究了催化剂制备因素,催化剂的结构及表面特性对催化活性的影响。     

Rose Bengal-Cu-TiO2的制备及可见光制氢活性研究

用光还原方法制备了负载Cu的光催化剂Cu-TiO2，并通过染料Rose bengal敏化，制备了具有可见光活性的Rose bengal-Cu-TiO2光催化剂，通过可见光下光解水制氢考察了催化剂的活性，并利用XRD、UV-Vis等手段对样品进行了表征。实验表明：载Cu增强了TiO2对可见光的吸收，Cu负载量对催化剂活性有一定的影响，Cu的最佳负载量为5％（质量分数）。Cu的负载也增加了TiO2对染料的吸附强度和吸附量，从而提高了TiO2对可见光的吸收和光催化活性。但载Cu的TiO2催化剂的活性和传统的载贵金属Pt的TiO2催化剂相比，其光催化活性较低，有待进一步提高．     

TiO2-SiO2复合薄膜光催化活性的研究进展

TiO2-SiO2复合薄膜相对纯TiO2薄膜更有利于提高光催化活性,针对TiO2-SiO2复合薄膜在提高光催化活性方面表现的优异性能,论述了其提高光催化活性的机理。根据近年来国内外TiO2-SiO2复合薄膜的研究现状,对溶胶-凝胶法、离子自组装成膜技术、射频磁控共溅射法、液相沉积法、化学气相法等制备方法的研究进展进行了综述,并对其优缺点进行了比较和评述。展望了TiO2-SiO2复合薄膜进一步研究的方向和需要解决的问题。     

Pt/TiO2-NTs复合材料的制备及其甲醇电氧化机理研究

采用水热法合成锐钛矿型TiO2纳米管(TiO2-NTs),并以其为载体制备了Pt/TiO2-NTs复合材料。用TEM、XRD对复合材料的形貌和结构进行了表征,TEM测试表明Pt纳米粒子以簇状形式均匀地分散在TiO2纳米管表面。运用循环伏安法研究了Pt/TiO2-NTs复合材料在不同条件下对硫酸中甲醇的电催化活性,并讨论了甲醇的电氧化机理。结果表明,Pt/TiO2-NTs复合材料具有出色的电催化活性。因此,TiO2-NTs被认为是非常有潜力的燃料电池贵金属催化剂载体材料。     

纳米TiO2／Al2O3复合薄膜光催化特性研究

以电化学方法合成的Al2O3多孔膜为基体，采用交流电沉积的方法在膜孔中沉积纳米TiO2，制备出纳米TiO2／Al2O3复合薄膜。对TiO2／Al2O3复合薄膜的形貌、结构和组成进行了表征；对TiO2／Al2O3复合薄膜光催化甲基橙溶液进行了研究。结果表明Al2O3／TiO2复合薄膜呈现出较好的光催化活性，电沉积TiO2的时间、热处理温度、选择不同光源照射均对TiO2／Al2O3复合薄膜光催化活性有一定的影响。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.     

新闻(英文)

正China and Greece Sign the Standardization Cooperation Agreement Witnessed by Chinese Premier Li Keqiang and Greek Prime Minister Antonis Samaras,AQSIQ Minister Zhi Shuping and ELOT Chairman and Executive Director Angelos Tolkas signed the SAC-ELOT Standardization Cooperation Agreement.The Agreement is one of the critical cooperation documents signed during Li Keqiang’s visit in Greece,encouraging China and Greece to