Small fatigue crack growth behavior of titanium alloy TC4 at different stress ratios

In this paper, the small fatigue crack behavior of titanium alloy TC4 at different stress ratios was investigated. Single‐edge‐notch tension specimens were fatigued axially under a nominal maximum stress of 370 MPa at room temperature. Results indicate that fatigue cracks in TC4 initiate from the interface between α and β phases or within α phase. More than 90% of the total fatigue life is consumed in the small crack initiation and growth stages. The crack growth process of TC4 can be divided into three typical stages, ie, microstructurally small crack stage, physically small crack stage, and long crack stage. Although the stress ratio has a significant effect on the total fatigue life and crack initiation life at constant σ_max, its effect on crack growth rate is indistinguishable at R = ?0.1, 0.1, and 0.3 when crack growth rate is plotted as a function of ?K.     

The effect of microstructures on fatigue crack growth in Q345 steel welded joint

It is a traditional that the fatigue crack growth behavior is sensitive to microstructure in threshold regime, while it is sensitive to R‐ratio in Paris regime. Fatigue test is carried out for welded joints of a Q345 steel where the compact tension specimens with 3.8 and 12.5 mm thickness are used, and comparisons of fatigue crack growth behavior between base metal and a few different locations in the welded joint are considered in Paris regime. Welding residual stresses are removed by heat treatment to focus the study on the microstructural effect. It is shown that fatigue crack growth rate (FCGR) in the base metal is not sensitive to R‐ratio, but the FCGR increases in the overheated zone, the fusion zone and the weld metal zone with R‐ratio increasing. To the low R‐ratio, FCGR in the three zones is smaller than that in the base metal, but they approximate the same with base metal under the high R‐ratio. The mechanism of fatigue crack growth is analyzed through crack path in microstructures and SEM fractograph. The coarse‐grained ferrite in the base metal is of benefit to relaxation of the average stress at the crack tip, and the fatigue crack growth predicts branching and deflection within above different locations in the welded joint. These tortuous crack paths with crack branching and deflection will promote crack closure as well as crack‐tip stress shielding and then resulted in higher crack growth resistance.     

Growth behaviour of small surface fatigue cracks in AISI 304 stainless steel

A series of axial tensile fatigue tests (R = 0.1) was carried out to investigate the initiation and the growth behaviours of very small surface fatigue cracks under two different surface conditions (viz. smooth and pitted surfaces) of AISI 304 stainless steel at room temperature. This paper deals with both of the two approaches regarding the analysis of fatigue: the approach based on the concept of fracture mechanics and low cycle fatigue. In particular, both the initiation and growth of cracks and the coalescence of small cracks by fatigue in the specimen have been investigated by the methods of surface replicas and photomicrographs. Quantitative information such as the initiation period, growth and coalescence behaviours of small cracks, and crack growth properties were systematically obtained. The results show that the accurate determination of these parameters is critical for the application of fracture mechanics to fatigue life assessment.     

Multiaxial fatigue of a short glass fibre reinforced polyamide 6.6 – Fatigue and fracture behaviour

The multiaxial fatigue behaviour of a short glass fibre reinforced polyamide 6.6 (PA66-GF35) is investigated on hollow tubular specimens in the range of fatigue lives between 10² and 10⁷ cycles. Fatigue experiments included pure tension, pure torsion, combined tension–torsion at different biaxiality ratios and phase shifting angles between the stress components. Tests were carried out with load ratio R = 0 and R = −1 at room temperature as well as at 130 °C. The influence of biaxiality ratio, phase angle between load components and load ratio is discussed.An extensive analysis of the fracture behaviour is performed on the specimens to recognise the crack nucleation and propagation mechanisms; failure modes were evaluated via optical and scanning electron microscopy.     

THREE-DIMENSIONAL CRACK-SHAPE EFFECTS DURING THE GROWTH OF SMALL SURFACE FATIGUE CRACKS IN A TITANIUM-BASE ALLOY

Abstract— A basic study was performed on the evolution of three-dimensional shapes of small surface fatigue cracks during fatigue, and the effect of this evolution on small-crack growth behavior of a titanium-base alloy. Specifically, the nature and the magnitude of variations in crack aspect ratio, a/c (a is the crack depth and c is the half-surface crack length), during cyclic crack growth and its impact on growth rates have been studied. Experiments were performed on naturally initiated micro-cracks in a microstructure consisting of equiaxed primary-α₂ phase in a Widmanstätten (transformed β) matrix. Several cracks under stress ratio (R) levels of 0.1 and ?1, were studied. A specialized experimental system, consisting of a laser interferometer (to measure precisely the small-crack surface displacements), and a photo microscope (to automatically and continuously photograph the fatigue micro-cracks) was employed in the study. Apparent aspect ratios of surface cracks were calculated from the compliance response and the surface crack length data as a function of fatigue cycles. These data enabled accurate calculations of growth rates at the surface crack tip as well as the tip at depth in the bulk over the entire crack growth period, thus giving an insight into the crack growth process. Measurements of closure levels of small cracks were also performed and were used to partly account for the differences in growth rates. In the comparisons of small-crack growth data with the large-crack data, surface growth rates correlated relatively well with the large-crack data. Growth rates at depth exhibited large variations due to the irregularity of crack fronts at this location, and these rates deviated significantly from the large-crack behavior. Additionally, these growth rates varied between different cracks. An attempt was made to rationalize these observations in terms of the effects of inhomogeneities present in the microstructure.     

Fatigue crack growth testing at negative stress ratios: discussion on the comparability of testing results

It is an accepted fact in fatigue community that compressive loads contribute to fatigue crack growth. Evidences range from fatigue crack growth under fully compressive loads to effects of compressive underloads to negative stress ratio loading. Because the crack closes under compression and the crack flanks transmit compressive stresses, the loading situation is completely different to those of tensile loading. The present paper addresses the comparability of crack growth testing procedures at negative stress ratios. It reveals that compressive loading at the crack tip differs in different specimens for an equal maximum stress intensity factor K_max and negative stress ratio R. Furthermore, the crack length can significantly influence the loading conditions at the crack tip for tension–compression loading. Depending on the specimen type and crack length, a negative force ratio may lead to a change of algebraic sign of the stresses at the crack tip or not. As a consequence, the comparability of available literature results for R ≤ 0 tests is not ensured. Proposals to improve the comparability of tension–compression crack growth testing will be given.     

Micro- and macro-approach to the fatigue crack growth in progressively drawn pearlitic steels at different R-ratios

This paper deals with the role of microstructure on the fatigue behaviour of pearlitic steels with different degrees of cold drawing. The analysis is focussed on the region II (Paris) of the fatigue behaviour, measuring the constants (C and m) for the different degrees of drawing. From the engineering point of view, the manufacturing process by cold drawing improves the fatigue behaviour of the steels, since the fatigue crack growth rate decreases as the strain hardening level in the material increases. In particular, the coefficient m (slope of the Paris laws) remains almost constant and independent of the drawing degree, whereas the constant C decreases as the drawing degree rises. The paper focuses on the relationship between the pearlitic microstructure of the steels (progressively oriented as a consequence of the manufacturing process by cold drawing) and the macroscopic fatigue behaviour. To this end, a detailed metallographic analysis was performed on the fatigue crack propagation path after cutting and polishing on a plane perpendicular to the crack front (fracto-metallographic analysis). It is seen that the fatigue crack growth path presents certain roughness at the microscopic level, such a roughness being related to the pearlitic colony boundaries more than to the ferrite/cementite lamellae interfaces. Fatigue cracks are transcollonial and exhibit a preference for fracturing pearlitic lamellae, with non-uniform crack opening displacement values, micro-discontinuities, branchings, bifurcations and frequent local deflections that create microstructural roughness. The net fatigue surface increases with cold drawing due to the higher angle of crack deflections. With regard to the influence of the R-ratio, an increase of such a stress ratio produces microcracking with a higher number of branchings for the same stress intensity range.     

Fracture toughness and growth of short and long fatigue cracks in ductile cast iron EN‐GJS‐400‐18‐LT

Heavy components of ductile cast iron frequently exhibit metallurgical defects that behave like cracks under cyclic loading. Thus, in order to decide whether a given defect is permissible, it is important to establish the fatigue crack growth properties of the material. In this paper, results from a comprehensive study of ductile cast iron EN‐GJS‐400‐18‐LT have been reported. Growth rates of fatigue cracks ranging from a few tenths of a millimetre (‘short’ cracks) to several millimetres (‘long’ cracks) have been measured for load ratios R=?1, R= 0 and R= 0.5 using a highly sensitive potential‐drop technique. Short cracks were observed to grow faster than long cracks. The threshold stress intensity range, ΔK_th, as a function of the load ratio was fitted to a simple crack closure model. Fatigue crack growth data were compared with data from other laboratories. Single plain fatigue tests at R=?1 and R= 0 were also carried out. Fracture toughness was measured at temperatures ranging from ?40 °C to room temperature.     

A crack propagation criterion based on ΔCTOD measured with 2D‐digital image correlation technique

The fatigue cracks growth rate of a forged HSLA steel (AISI 4130) was investigated using thin single edge notch tensile specimen to simulate the crack development on a diesel train crankshafts. The effect of load ratio, R, was investigated at room temperature. Fatigue fracture surfaces were examined by scanning electron microscopy. An approach based on the crack tip opening displacement range (ΔCTOD) was proposed as fatigue crack propagation criterion. ΔCTOD measurements were carried out using 2D‐digital image correlation techniques. J‐integral values were estimated using ΔCTOD. Under test conditions investigated, it was found that the use of ΔCTOD as a fatigue crack growth driving force parameter is relevant and could describe the crack propagation behaviour, under different load ratio R.     

Computer modelling application in life prediction of high temperature components

Defects introduced in pressure vessel components during fabrication processes act as potential sources for damage accumulation and subsequent catastrophic failure. Cracks nucleate at these stress risers and propagate aided by fatigue type of loading, corrosion and creep. Analysis of crack growth under conditions of ‘time-dependent fatigue’ is very important for the life prediction of pressure vessel components. In this paper the interaction of creep-hot corrosion and low cycle fatigue is analyzed based on the energy expended for the nucleation of damage at the advancing crack front. The total damage accumulation is divided into that due to (i) fatigue, (ii) corrosion and (iii) creep for modelling purpose. The analysis yields a relation in terms ofJ-integral which is applicable to both crack propagation and final failure. A corrosion-creep parameter (F _i ) has been introduced at the crack propagation stage and raw data from different sources have been analyzed for different types of loading and compared with the theoretical predictions. The total energy in tension which includes the tension going time, appears to be a good parameter for the prediction of time-dependent fatigue life.     

Multiaxial fatigue of rubber: Part II: experimental observations and life predictions

Fatigue experiments were conducted with an axial‐torsion specimen covering a wide range of stretch biaxiality and a range of fatigue lives between 10³ and 2 × 10⁶ cycles. These experiments include combined torsion–compression, pure torsion, combined torsion–tension and pure axial tension. Both in‐phase and out‐of‐phase combinations of axial and torsion loading were considered. The multiaxial fatigue experiments described provide empirical evidence from which an understanding of the mechanics of the fatigue process in rubber can be developed. Each of the four equivalence parameters described in Part I has been applied to the axial‐torsion fatigue experiments described in this paper (Part II). These results provide the basis for an analysis of the effects of multiaxial loading on fatigue life, and an assessment of the degree to which the various equivalence parameters are able to rationalize the results in a unified way. For the combined axial and shear strain histories in this study, the maximum principal strain criterion gave the best correlation to fatigue life. Strain energy density gave the worst correlation. The cracking energy density criterion was generally found to give good correlation of fatigue crack nucleation lives from combined axial‐torsion tests. Because it provides a plane‐specific analysis, this criterion appears to be particularly well suited for use in crack nucleation analyses of multiaxial strain histories.     

Crack growth behavior and fatigue-life prediction based on worst-case near-threshold data of a large crack for 9310 steel

ABSTRACT Both experimental and analytical investigations were conducted to study crack initiation and growth of small cracks, near‐threshold growth behavior of large cracks at constant R‐ratio/decreasing ΔK and constant K_max/decreasing ΔK, respectively, for 9310 steel. The results showed that a pronounced small‐crack effect was not observed even at R = ?1, small cracks initiated by a slip mechanism at strong slip sites. Worst‐case near‐threshold testing results for large cracks under several K_max values showed that an effect of K_max on the near‐threshold behavior does not exist in the present investigation. A worst‐case near‐threshold test for a large crack, i.e. constant K_max/decreasing ΔK test, can give a conservative prediction of growth behavior of naturally initiated small cracks. Using the worst‐case near‐threshold data for a large crack and crack‐tip constraint factor equations defined in the paper, Newman's total fatigue‐life prediction method was improved. The fatigue lives predicted by the improved method were in reasonable agreement with the experiments. A three‐dimensional (3D) weight function method was used to calculate stress‐intensity factors for a surface crack at a notch of the present SENT specimen (with r/w = 1/8) by using a finite‐element reference solution. The results were verified by limited finite‐element solutions, and agreed well with those calculated by Newman's stress‐intensity factor equations when the stress concentration factor of the present specimen was used in the equations.     

Fatigue crack initiation in Hastelloy X – the role of boundaries

In polycrystalline metals, microstructural features such as grain boundaries (GBs) influence fatigue crack initiation. Stress and strain heterogeneities, which arise in the vicinity of GBs, can promote the nucleation of fatigue cracks. Because of variations in grain size and GB types, and consequently variations in the local deformation response, scatter in fatigue life is expected. A deeper quantitative understanding of the early stages of fatigue crack nucleation and the scatter in life requires experimental and modelling work at appropriate length scales. In this work, experiments are conducted on Hastelloy X under fatigue conditions, and observations of fatigue damage are reported in conjunction with measurements of local strains using digital image correlation. We use a recent novel fatigue model based on persistent slip band–GB interaction to investigate the scatter in fatigue lives and shed light into the critical types of GBs that nucleate cracks. Experimental tools and methodologies, utilizing ex situ digital image correlation and electron backscatter diffraction, for high resolution deformation measurements at the grain level are also discussed in this paper and related to the simulations.     

A method to develop a unified fatigue life prediction model for filled natural rubbers under uniaxial loads

Rubber components are widely used in many fields because of their superior elastic properties. Fatigue failures, commonly encountered in rubber components, however, remain a critical issue. In this study, the effect of strain ratio R on the fatigue life of filled natural rubbers used in automotive mounts is investigated experimentally and numerically. A uniaxial tension/compression fatigue experiment was conducted on dumb‐bell cylindrical rubber specimens subject to loads representing different R ratios. The experimental fatigue data are used to formulate two preliminary fatigue models based on peak strain and strain amplitude as the damage parameters. The deficiencies of these two models in predicting fatigue life over a wide range of R ratios are discussed, and an alternative life prediction model is proposed. The proposed model incorporates the effect of R ratio using an equivalent strain amplitude. It is shown that the proposed model could effectively predict fatigue life over a wide range of R ratios with an improved accuracy.     

Behaviour of short cracks in alloy 800HT under biaxial fatigue

Biaxial in phase fatigue tests were carried out on thin walled tube specimens of alloy 800HT at ambient temperature. The loading modes included tension, torsion, and combined tension—torsion with a tensile/shear plastic strain range ratio Δ?p/Δγp = 3^1/2. The influence of effective strain amplitudes and biaxiality on the initial growth of fatigue cracks was investigated using the replica technique. The results indicated that the loading conditions strongly affected the growth rates of short cracks. In torsion the cracks grew significantly more slowly than under axial or biaxial loading. A mean tensile stress perpendicular to the shear crack promoted its growth and reduced the fatigue life. The growth of the cracks could be described by the ΔJ integral for axial and biaxial loading; the integration predicted the fatigue life under axial and biaxial loading correctly. However, significantly conservative lifetime predictions were obtained for pure torsional loading since ΔJ does not include crack closure and crack surface rubbing.

MST/3234     

Fretting fatigue limit as a short crack problem at the edge of contact

This paper proposes a local stress concept to evaluate the fretting fatigue limit for contact edge cracks. A unique S–N curve based on the local stress could be obtained for a contact edge crack irrespective of mechanical factors such as contact pressure, relative slip, contact length, specimen size and loading type. The analytical background for the local stress concept was studied using FEM analysis. It was shown that the local stress uniquely determined the ΔK change due to crack growth as well as the stress distribution near the contact edge. The condition that determined the fretting fatigue limit was predicted by combining the ΔK change due to crack growth and the ΔK_th for a short crack. The formation of a non‐propagating crack at the fatigue limit was predicted by the model and it was experimentally confirmed by a long‐life fretting fatigue test.     

Prediction of rubber fatigue life under multiaxial loading

The process of fatigue failure of materials is generally described by two phases: crack initiation and crack propagation. This study concerns the crack initiation in rubbers submitted to a cyclic loading. A parameter based on the strain energy density (SED) and predicting the onset of primary crack and its probable orientation has been identified for such materials according to the investigations of Mars and Fatemi. More precisely, this criterion has been analytically developed in the cases of simple tension, biaxial tension and simple shear loadings by assuming large strains. The results denote the possibility to predict the orientation plane in which the primary crack would be expected to occur in a material. Then, it was implemented in a finite‐elements (FE) program in order to be applied to structures under any kind of the strain states. A good agreement was obtained between FE and analytical results for the usual strain states. Finally, to evaluate lifetime up to crack nucleation, we have achieved a set of experimental fatigue tests using uniaxial tension (UT) and pure shear (PS) test specimens containing a hole in order to localize the crack initiation. The obtained results proved the efficiency of the criterion to describe the fatigue life of rubbers under multiaxial loading.     

Stress intensity factors for a wide range of long-deep semi-elliptical surface cracks, partly through-wall cracks and fully through-wall cracks in tubular members

To calculate the rate of fatigue crack growth in tubular members, one approach is to make use of the fracture mechanics based Paris law. Stress intensity factors (SIF) of the cracked tubular members are prerequisite for such calculations. In this paper, stress intensity factors for circumferential deep semi-elliptical surface crack (a/t > 0.8), semi-elliptical partly through-wall crack and fully through-wall crack cracks in tubular members subjected to axial tension are presented. The work has produced a comprehensive set of equations for stress intensity factors as a function of a/T, c/πR and R/T for deep surface cracks. For the partly through-wall cracks and fully through-wall cracks, two sets of bounding stress intensity factor equations were produced based on which all stress intensity factors within the range of parameters can be obtained by interpolation.     

Investigation of small fatigue crack initiation and growth behaviour of nickel base superalloy GH4169

Surface replication method was utilized to monitor the small fatigue crack initiation and growth process of single‐edge‐notch tension specimens fabricated by nickel base superalloy GH4169. Three different stress levels were selected. Results showed that small fatigue cracks of nickel base superalloy GH4169 initiated from grain boundaries or surface inclusions. The small fatigue crack initiation and growth stages took up about 80–90% of the total fatigue life. Multiple major cracks were observed in the notch root, and specimen with more major cracks seemed to have smaller fatigue life under the same test conditions. At the early growth stage, small crack behaviour might be strongly influenced by microstructures; thus, the crack growth rates had high fluctuations. However, the stress level effect on the small fatigue crack growth rates was not distinguishable for the three different stress levels. And no clear differences were found among the crack initiation lives by using replication technique.     

On the fatigue crack growth behaviour of selective laser melting fabricated Inconel 625: Effects of build orientation and stress ratio

The building of Inconel 625 material was carried out using the selective laser melting method, and its fatigue crack growth property at ambient temperature was experimentally investigated. Compact‐tension specimens with different building orientations were utilized to determine the stress intensity factor threshold and fatigue crack growth rate curves at different stress ratios (R). The results indicated that the fatigue crack growth properties in the near threshold stress intensity factor and Paris regions were greatly affected by the loading factor, as well as the orientation of the alloy. The mechanism of fatigue crack growth at different stages was observed and discussed using scanning electron microscopy. Finally, based on the framework of the linear elastic fracture, a new and applicable effective driving force factor range was introduced to replace the traditional stress intensity factor range (ΔK) with good accuracy for all of the fatigue crack growth test data, considering both the stress ratio and orientation.