CH4-CO2 reforming over Ni/Al2O3 aerogel catalysts in a fluidized bed reactor

Ni/Al₂O₃ aerogel catalysts were synthesized by a sol-gel method combined with a supercritical drying route. The catalytic performances of the catalysts in methane reforming with CO₂ were investigated in a quartz micro-reactor. The results indicated that the aerogel catalyst showed higher specific surface area and higher dispersivity of nickel species than those of impregnation catalyst. The excellent catalytic performances and stabilities were achieved over the aerogel catalysts in the fluidized bed reactor. Comprehensive characterization with TG, XRD and FESEM revealed that the aerogel catalyst in the fluidized bed had much lower carbon deposition than that in the fixed bed. The fluidization of the aerogel catalyst greatly improved the contact efficiency of gas-solid phase, which accelerated the gasification of the deposited carbon. In contrast, the deactivation of the aerogel catalyst was caused by the carbon deposition due to the catalyst without moving in the fixed bed. Moreover, decreasing activity of the impregnation catalyst in the fluidized bed resulted from the poor fluidization state of catalyst particles and low effective active sites on surface of catalyst.     

Characterization of aerogel Ni/Al2O3 catalysts and investigation on their stability for CH4-CO2 reforming in a fluidized bed

The CH₄-CO₂ reforming was investigated in a fluidized bed reactor using nano-sized aerogel Ni/Al₂O₃ catalysts, which were prepared via a sol–gel method combined with a supercritical drying process. The catalysts were characterized with BET, XRD, H₂-TPR and H₂-TPD techniques. Compared with the impregnation catalyst, aerogel catalysts exhibited higher specific surface areas, lower bulk density, smaller Ni particle sizes, stronger metal-support interaction and higher Ni dispersion degrees. All tested aerogel catalysts showed better catalytic activities and stability than the impregnation catalyst. Their catalytic stability tested during 48 h reforming was dependent on their Ni loadings. Characterizations of spent catalysts indicated that only limited graphitic carbon formed on the aerogel catalyst, while massive graphitic carbon with filamentous morphology was observed for the impregnation catalyst, leading to significant catalytic activity degradation. An aerogel catalyst containing 10% Ni showed the best catalytic stability and the lowest rate of carbon deposition among the aerogel catalysts due to its small Ni particle size and strong metal-support interaction.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Steady State Isotopic Transient Kinetic Analysis of Flameless Methane Combustion over Pd/Al2O3 and Pt/Al2O3 Catalysts

The SSITKA measurements were performed in the steady state of complete methane oxidation on the Pd/Al₂O₃ and Pt/Al₂O₃ catalysts. It was found that the number of intermediates and their average life-time on the catalyst surface changes with the increase of reaction temperature. On the Pd/Al₂O₃ catalyst there is larger number of active centres than on Pt/Al₂O₃ catalyst which permits the course of methane oxidation at lower temperatures.     

Preparation and characterization of NiO/MgO/Al2O3 supported CoPcS catalyst and its application to mercaptan oxidation

MgO/Al₂O₃ and NiO/MgO/Al₂O₃ solid bases were prepared by mixing method. The samples were characterized by X-ray diffraction (XRD), CO₂ temperature-programmed desorption (CO₂-TPD) and surface area measurements. After supported sulfonated cobalt phthalocyanine (CoPcS) the catalytic performance of these catalysts was evaluated in the mercaptan oxidation reaction. The effect of Mg/Al mole ratios on activity, crystal structure, basicity and stability in air was discussed. And the mechanism of the effect of NiO was identified. Results show that the base amount of MgO/Al₂O₃ increases with increasing Mg/Al mole ratio and catalyst with high Mg/Al mole ratio has a higher initial activity. NiO/MgO/Al₂O₃–CoPcS shows a higher initial activity and a much longer lifetime than MgO/Al₂O₃–CoPcS. When nickel oxide is doped into the MgO/Al₂O₃ support more crystal defects are generated, which increases the amount and types of basic sites.     

Development of a multi-layered micro-reactor coated with Pt–Co/Al2O3 catalyst for preferential oxidation of CO

Pt–Co/Al₂O₃ catalysts were prepared with different Co/Pt weight ratios (0.3–1.8) and their performances for preferential oxidation of CO (PROX) were tested. The activity of the catalyst increased with Co/Pt weight ratio due to the increase of the area of active phase by interaction between Pt and Co species. The 13-layered micro-channel reactor was prepared by stacking the plates coated with Pt–Co/Al₂O₃ catalyst. The reactor was divided into three parts (inlet, middle, and outlet) to evaluate the performance of each part. Most of O₂ supplied was depleted at the inlet part and the temperature gradient of the reactor occurred due to the high exothermicity of oxidations of CO and hydrogen. In order to prevent hot spot and temperature gradient, the reactor with non-uniform distribution of the catalyst (partially coating the catalyst on the channels) was prepared. The prepared reactor showed uniform temperature distribution and exhibited excellent performance for PROX.     

Synergetic effect of combined use of Cu–ZnO–Al2O3 and Pt–Al2O3 for the steam reforming of methanol

Commercial Cu–ZnO–Al₂O₃ catalysts are used widely for steam reforming of methanol. However, the reforming reactions should be modified to avoid fuel cell catalyst poisoning originated from carbon monoxide. The modification was implemented by mixing the Cu–ZnO–Al₂O₃ catalyst with Pt–Al₂O₃ catalyst. The Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture created a synergetic effect because the methanol decomposition and the water–gas shift reactions occurred simultaneously over nearby Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalysts in the mixture. A methanol conversion of 96.4% was obtained and carbon monoxide was not detected from the reforming reaction when the Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture was used.     

Selective synthesis of mixed alcohols from syngas over catalyst Fe2O3/Al2O3 in slurry reactor

The Fe₂O₃/Al₂O₃ catalyst was studied to selectively synthesize mixed alcohols from syngas in a continuously stirred slurry reactor with the oxygenated solvent Polyethylene Glycol-400 (PEG-400). The selectivity of mixed alcohols in the products reached as high as 95 wt.% and the C₂₊ alcohols (mainly ethanol) was more than 40 wt.% in the total alcohol products at the reaction conditions of 250 °C, 3.0 MPa, H₂/CO = 2 and space velocity = 360 ml/g_cat h. The hydrogen temperature programmed reduction (H₂-TPR) and X-ray photoelectron spectroscopy (XPS) measurements of the catalyst confirmed that the FeO phase was responsible for the high selectivity to mixed alcohols in the process. And the oxygenated solvent PEG-400 was also necessary for the selective synthesis of mixed alcohols in the reaction system.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

Role of ZnO in Cu/ZnO/Al2O3 catalyst for hydrogenolysis of butyl butyrate

For hydrogenolysis of butyl butyrate (BB), a series of Cu/ZnO/Al₂O₃ catalysts with different metal compositions were prepared, and characterized by N₂O chemisorption for measuring Cu surface area and by chromatographic experiment for determining the heat of BB adsorption. As a result, the presence of ZnO in Cu-based catalysts was found to enhance the catalytic activity of Cu due to dual function of ZnO. The Cu surface area was linearly correlated with the butanol productivity, demonstrating that ZnO exerts the structural function in Cu/ZnO/Al₂O₃ catalysts. Additionally, the role of ZnO as a chemical contributor was revealed such that its presence leads to lower activation energy of the surface reaction, thus resulting in higher Cu catalytic activity obtained at a low temperature such as 200 °C. Consequently, optimizing the Cu/Zn ratio in Cu/ZnO/Al₂O₃ catalyst is required to tune its structural and chemical characteristics of Cu metals, and thus to obtain a higher activity on the hydrogenolysis reaction.     

A novel solid superbase of Eu2O3/Al2O3 and its catalytic performance for the transesterification of soybean oil to biodiesel

A novel solid superbase catalyst of Eu₂O₃/Al₂O₃ was prepared and its basic strength reached 26.5 measured by indicators according to Hammett scale. The catalytic activity of Eu₂O₃/Al₂O₃ was evaluated for the transesterification of soybean oil with methanol to biodiesel in the fixed bed reactor and under atmospheric pressure. The results show that Eu₂O₃/Al₂O₃ is an excellent catalyst for the transesterification of soybean oil, and the conversion of soybean oil can reach 63.2% at 70 °C for 8 h.     

ZrO2/SiO2- and La2O3/Al2O3-supported platinum catalysts for CH4/CO2 reforming

Surface-phase ZrO₂ on SiO₂ (SZrOs) and surface-phase La₂O₃ on Al₂O₃ (SLaOs) were prepared with various loadings of ZrO₂ and La₂O₃, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH₄/CO₂ reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al₂O₃ and Pt/SiO₂ catalysts. CO₂ or CH₄ pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides.

The zirconia can be homogeneously dispersed on SiO₂ to form a stable surface-phase oxide. The lanthana cannot be spread well on Al₂O₃, but it forms a stable amorphous oxide with Al₂O₃. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO₂ and Pt/Al₂O₃ by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO₂ and Pt/Al₂O₃ catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO₂ adsorbed on the basic sites of SZrOs and SLaOs.     

A thermogravimetric study of the partial oxidation of methanol for hydrogen production over a Cu/ZnO/Al2O3 catalyst

The partial oxidation of methanol for the production of hydrogen was investigated in both a fixed-bed microreactor and in a thermogravimetric analyzer (TG-FTIR) from 180 °C to 250 °C using a commercial Cu/ZnO/Al₂O₃ catalyst. In the microreactor, a hot spot in the undiluted catalyst bed of 4 K and 32 K was observed at 180 °C and 220 °C, respectively. Methanol conversion was strongly accelerated between 180 °C and 220 °C. In the TG-FTIR experiments, the reduced copper was completely oxidized to cuprite, Cu₂O, with increasing time-on-stream in the presence of oxygen and methanol (O₂/MeOH = 0.5) at 180 °C. The selectivity to formaldehyde increased in the same manner as the catalyst was oxidized to cuprite. In contrast, at 250 °C the catalyst remained completely reduced for the same O₂/MeOH ratio. Two main reaction pathways are proposed explaining the influence of the copper oxidation state on the product distribution.     

Influence of composition of MgAl2O4 supported NiCeO2ZrO2 catalysts on coke formation and catalyst stability for dry reforming of methane

Dry reforming of methane was studied over Ni catalysts supported on γAl₂O₃, CeO₂, ZrO₂ and MgAl₂O₄ (670 °C, 1.5 bar, 16–20 l CH₄ ml_catalyst⁻¹ h⁻¹). It is shown that MgAl₂O₄ supported Ni catalysts promoted with both CeO₂ and ZrO₂ are promising catalysts for dry reforming of methane with carbon dioxide. Within a certain composition range, the simultaneous promotion with CeO₂ and ZrO₂ has great influence on the amount of coke and the catalyst service time. XRD analyses indicate that formation of crystalline Ce_xZr_1−xO₂ mixed oxide phases occurs on double promotion. In particular, incorporation of low amounts of Zr in the CeO₂ fluorite structure provides stable dry reforming catalysis. As shown with TPR, promotion leads to a higher reduced state of Ni. SEM, XRD and TPR analyses demonstrate that highly dispersed, doubly promoted Ni catalysts with a strong metal-support interaction are essential for stable dry reforming and suppression of the formation of carbon filaments.     

Production of hydrogen by steam reforming of bio-oil over Ni/Al2O3 catalysts: Effect of addition of promoter and preparation procedure

Catalytic steam reforming of bio-oil was investigated in a fixed bed tubular reactor for production of hydrogen. Two series of nickel/alumina (Ni/Al₂O₃) supported catalysts promoted with ruthenium (Ru) and magnesium (Mg) were prepared. Each catalyst of the first series (Ru–Ni/Al₂O₃) was prepared by co-impregnation of nickel and ruthenium on alumina. They were examined to investigate the effect of adding ruthenium on the performance of the catalysts for hydrogen production. The effect of the temperature, the most effective parameter in the steam reforming of bio-oil, on the activity of the catalysts was also investigated. Each catalyst of the second series (Ni–MgO/Al₂O₃) was prepared by consecutive impregnation using various preparation procedures. They were tested to determine the effect of adding magnesium as well as the effect of the preparation procedure on the outlet gas concentrations. It was shown that in both series, the catalysts were more efficient in hydrogen production as well as carbon conversion than Ni/Al₂O₃ catalysts. The highest hydrogen yield was 85% which was achieved over Ru–Ni/Al₂O₃ at 950 °C. It was also found that the effect of adding a small amount of ruthenium was superior to that of nickel on the yield of hydrogen when the nickel content was equal to or greater than 10.7%.     

Phase diagram of the Al2O3-HfO2-Y2O3 system

The phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system was first constructed in the temperature range 1200-2800 °C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this system. Four new ternary and three new quasibinary eutectics were found. The minimum melting temperature is 1755 °C and it corresponds to the ternary eutectic Al₂O₃ + HfO₂ + Y₃Al₅O₁₂. The solidus surface projection, the schematic of the alloy crystallization path and the vertical sections present the complete phase diagram of the Al₂O₃-HfO₂-Y₂O₃ system.     

Chemical kinetic modelling of the effect of NO on the oxidation of CH4 under fluidized bed combustor conditions

The ignition and burnout of the volatiles in fluidized bed combustor are essential for its performance and emissions. NO_x are known to sensitize the oxidation of hydrocarbons, CO, and H₂. This effect is relevant especially for fluidized bed combustors, which are operated at relatively low temperatures (i.e. about 850 °C). Different reaction mechanisms and modifications to existing mechanisms have been proposed in the literature to account for these low temperature interactions of NO_x and hydrocarbons. In this work, an existing widely used reaction mechanism is adapted and tested for its capability to describe the NO sensitized oxidation of CH₄ under conditions relevant to fluidized bed combustion. NO lowers the ignition temperature to about 300 °C under the conditions investigated. Three different oxidation paths for the oxidation of CH₄ have been identified and discussed. Their relative importance strongly depends on combustion temperature, indicating that the presence of NO_x significantly affects the oxidation of the volatiles in fluidized bed combustion.     

Ni/Al2O3 catalysts and their activity in dehydrogenation of methylcyclohexane for hydrogen production

Previous results on different catalysts revealed that methylcyclohexane underwent selective dehydrogenation to form toluene and hydrogen. This reaction system is a useful prototype model for similar systems in the chemical process and petroleum refining industries, such as hydrotreating for aromatics reduction, desulfurization, denitrogenation, reforming for aromatics reduction, dehydrocyclization, and fuel processing of liquid hydrocarbons in the generation of hydrogen feed for fuel cells. Dehydrogenation of methylcyclohexane to toluene is a method for hydrogen storage in the form of liquid organic hydrides. The efficiency of the dehydrogenation reactions and the quantity of products depend on the catalyst used. In the case of the dehydrogenation of methylcyclohexane to toluene, a metallic function, usually platinum is required as the catalyst. Although, there were some different catalysts used by former researchers, there was almost no investigation about the use of the nickel catalysts for this reaction. From the economical point of view, more efficient catalysts and reaction engineering methods should be developed for these reactions.In this work dehydrogenation of methylcyclohexane was performed in a fixed-bed catalytic reactor in the temperature range of 653–713 K on prepared Ni/Al₂O₃ catalysts having 5, 10, 15 and 20 wt.% Ni content. The inlet flowrates of methylcyclohexane and hydrogen to the reactor were changed by keeping one of them constant in order to investigate their effects on this reaction.     

Effect of Co and Rh promoter on NOx storage and reduction over Pt/BaO/Al2O3 catalyst

Effect of cobalt and rhodium promoter on NO_x storage and reduction (NSR) kinetics was investigated over Pt/BaO/Al₂O₃. Kinetics of 2% cobalt loading over Pt/BaO/Al₂O₃ demonstrated highest NO_x uptake during lean cycle, while reduction efficiency during rich cycle appeared most poor. In contrast to this, rhodium showed suppressing effect of NO_x uptake during lean cycle and demonstrated an enhanced effect for the higher efficiency of NO_x reduction during rich cycle. DRIFT study for NO_x uptake and regeneration confirmed formation of surface BaNO_x from the band at 1300 cm⁻¹ and formation of bulk BaNO_x from the band at 1330 cm⁻¹.