PVPK30和Tween80对中空纤维超滤膜结构和性能的影响

通过考察添加剂-聚乙烯吡咯烷酮（PVPK30）和Tween80对杂萘联苯聚醚砜酮（PPESK）中空纤维超滤膜结构和分离性能的影响，发现：随高分子添加剂聚乙烯吡咯烷酮K30浓度的升高，膜水通量减小，截留率基本无变化，膜结构逐渐由指状结构转变成海绵状结构。有机大分子添加剂Tween80可以提高膜的水通量，但膜结构不随添加剂浓度而改变，均为指状结构。当Tween80浓度小于5wt％时，随Tween80浓度的增加，膜水通量升高，截留率下降。比较不同凝胶浴温度下的膜分离性能可以看到，凝胶浴温度提高可以显著提升膜的纯水通量。     

高性能中空纤维超滤膜结构和性能研究

以含二氮杂萘酮结构的聚醚砜酮(PPESK)为膜材料,N-甲基-2-吡咯烷酮为溶剂,一缩二乙二醇、乙二醇甲醚和丁酮为添加剂,采用干-湿相转化技术制备了中空纤维非对称超滤膜。结果表明,聚合物浓度、添加剂类型和添加剂浓度的变化导致了超滤膜的形态逐渐由长而宽的指状孔结构变为海绵状结构,同时也对超滤膜的性能产生了较大的影响,所制得的PPESK超滤膜在0 1MPa的操作压力下对PEG10000的截留率高于95%,纯水通量可高达约159L/(m2·h)。     

添加剂对聚醚砜酮超滤膜结构和性能的影响

在杂萘联苯聚醚砜酮(PPESK)铸膜液中,分别添加磺化聚醚砜酮(SPPESK)、聚乙二醇(PEG)、有机小分子和无机盐添加剂,采用相转化法制备了聚醚砜酮超滤膜,并通过扫描电镜和超滤性能测试考察了不同添加剂对超滤膜结构和性能的影响。结果表明,SPPESK的加入提高了膜的亲水性和孔隙率,使膜的渗透性显著提高。有机高分子添加剂PEG的加入,使膜亚层指状孔结构向海绵状孔结构转变。改善了孔道的连通性,提高了膜的亲水性和孔隙率,使膜的纯水通量增加而截留率略有下降。含有羟基的醇类和酸类小分子添加剂有助于纯水通量的提高。无机盐添加剂起到成孔和增溶聚合物的作用。在保持截留率相对较高的条件下,LiCl和ZnCl2可以提高膜的纯水通量。FeCl2在成膜过程中发生水解氧化,部分铁均匀分布在膜三维空间中,与聚合物相互作用,改善膜的结构和性能。     

凝胶相转化温度和空气预蒸发时间对PVDF超滤膜性能及结构的影响

利用非溶剂相转化法(NIPS),以聚偏氟乙烯(PVDF)/聚乙烯吡咯烷酮(PVP)/N,N-二甲基乙酰胺( DMAC)为铸膜液体系,水为凝固浴制备了大通量超滤膜.考察了铸膜液温度、凝胶浴温度、空气预蒸发时间等条件对超滤膜性能与结构的影响.研究结果显示,随着铸膜液和凝胶浴温度的提高,膜纯水通量增大,强度增强,截留率降低,膜的第一泡点压力减小,膜的孔隙率随铸膜液温度升高而增大,随凝胶浴温度升高先增大后减小,膜断面指状孔发育较为通透,海绵层致密.延长铸膜液在空气预蒸发时间,膜的第一泡点压力和孔隙率降低,超滤膜截留率提高,通量和强度变化不大.     

聚乙二醇对氯化聚氯乙烯超滤膜微观结构及其性能的影响

探讨了聚乙二醇(PEG)及其分子量对氯化聚氯乙烯(CPVC)铸膜液黏度及其超滤膜微观结构和性能(纯水通量、截留率、机械性能和耐污染性能)的影响。结果表明,随着PEG分子量的增大,CPVC铸膜液黏度增大,CPVC超滤膜表面由网络大孔结构变为致密结构,PEG400和600对CPVC超滤膜断面微观结构没有太大影响,仍然保持海绵状结构,PEG相对分子质量超过1 000以后,CPVC超滤膜断面变为指状大孔结构与皮层构成非对称结构。铸膜液中添加PEG后,CPVC超滤膜纯水通量大幅度上升,但是截留率有不同程度的下降;随着PEG分子量的增大,CPVC超滤膜的纯水通量,耐污染性能及截留率均呈上升趋势。综合比较,PEG600作为添加剂,CPVC超滤膜能获得较好的性能。     

凝胶浴条件对PVDF/CaCO3共混中空纤维膜性能和结构的影响

采用干-湿相转化法制备了PVDF/CaCO3共混中空纤维膜,考察了芯液组成和外凝胶浴温度对共混膜结构和性能的影响。结果表明,随芯液中酸含量增加,膜纯水通量迅速升高,BSA截留率略有下降;膜拉伸强度下降,断裂伸长率增加。SEM图显示,膜断面指状孔的数量增多、支撑层厚度变薄、膜亚层海绵孔增加;相应孔隙率升高,而泡点压力略微下降。当外凝胶浴温度较高时,膜支撑层和外皮层较为致密,导致膜纯水通量明显下降,同时BSA截留率在80℃高温外凝胶浴时,由于膜外皮层上出现少量大孔结构,而迅速下降为62.55%。     

低截留分子质量新型聚芳醚腈酮超滤膜的研制

以新型聚芳醚腈酮为膜材料 ,以N -甲基 - 2 -吡咯烷酮 (NMP)为溶剂 ,研究了聚合物浓度、添加剂种类及含量、凝胶浴温度等对超滤膜性能的影响。结果表明 ,聚合物质量分数以 1 2 %～ 1 3 %为合适的制膜浓度 ,以聚乙二醇PEG - 4 0 0为添加剂时获得了高截留率和高水通量的超滤膜。随着凝胶浴温度的升高 ,水通量明显增大 ,而截留率有所下降 ,而共聚物的浓度增加则有相反的效果。制得的超滤膜具有较低的截留分子量 (PEG- 2 0 0 0 ) ,将制得的超滤膜用于达旦黄、黄X-G等染料的分离 ,截留率均达 90 %以上     

七通道中空纤维超滤膜的制备与性能调控

以聚醚酰亚胺(PEI)为膜材料、N,N-二甲基乙酰胺为溶剂、水为凝固浴,采用干-湿相转化法制备七通道中空纤维超滤膜,研究了PEI含量和3种添加剂γ-丁内酯、聚乙二醇600(PEG600)、聚乙烯吡咯烷酮-K30对膜结构和性能的影响。结果表明,随着PEI含量升高,膜断面由指状孔向海绵状孔转化,拉断力和爆破压力大幅提升。以PEG600为添加剂时膜具有最佳的综合性能,拉断力为16.55 N,纯水通量为247.39 L/(m~2·h),对牛血清白蛋白的截留率达93.9%。     

新型聚芳醚腈酮中空纤维超滤膜的研究

以含二氮杂萘酮结构聚芳醚腈酮(PPENK)为膜材料,N-甲基-2-吡咯烷酮(NMP)为溶剂,采用干-湿相转化法制备了中空纤维超滤膜.考察了聚合物浓度、添加剂含量以及纺丝过程中空气间隙、凝胶浴温度和纤维壁厚对膜结构及性能的影响.结果表明,当聚合物浓度为13%,添加剂EgOH含量α=0.9时,膜通量可达770 L·m-2·h-1,对BSA的截留率在90%以上;增大空气间隙可使膜的截留性能提高,但膜通量有所下降,最佳空气间隙为5～8cm;凝胶浴温度的升高增大了膜的通量,截留率下降幅度不大,凝胶浴温度宜控制在21～25℃范围内;纤维壁厚在0.15～0.18 mm时膜性能最佳.     

聚砜管式超滤膜的制备及其结构性能研究

采用浸没相沉淀法制备聚砜(PSF)管式超滤膜。以纯水通量、卵清蛋白截留率、扫描电镜表征膜的结构和性能,考察了PSF含量、凝固浴温度和组成、添加剂种类和含量对PSF管式膜成膜性能及结构的影响。结果表明,凝固浴温度升高、聚乙烯吡咯烷酮(PVP)含量增加、PEG-400含量增加,都可以使膜的水通量增加、截留率降低;而凝固浴中添加溶剂二甲基乙酰胺(DMAc)、铸膜液中PSF含量的增加,都可以使膜的通量减小,截留率升高。     

氢气纯度分析方法准确性的探讨

ONACCURACYOFANALYSISOFOFHYDROGEN1前言我公司目前应用的氢气纯度分析方法有两种,一种是爆炸反应法,另一种是焦性没食子酸吸收法。几年来,人们对两种分析方法的准确性曾有过褒贬不一的评论。这里我们也谈谈自己粗浅的观点。2爆炸法测定氢气纯度一定量的氢气样品与适量的空气之均匀混合物因反应后生成液体水而引起气体体积减少,减少的体积等于参加反应气体体积之和。其中l／3为氧气,2／3为氢气。根据氢气取样量和反应前后混气体体积之差,以及氢气在反应中的体积比例关系,可计算出样品的氢气纯度。计算公式式中：A一混…     

COMPARISON OF METHODS OF ANALYSIS OF GYPSUM1

The different analytical methods proposed for the evaluation of gypsum have been subjected to an experimental test. A combination method, consisting of a fusion with KHCO₃ and determination of CaO by KMnO₄ titration, the SO₃ by Andrews method of titration of BaCrO₄ has been found to give very reliable results with the least consumption of time.     

SEDIMENTATION OF BINARY MIXTURES OF PARTICLES OF UNEQUAL DENSITIES AND OF DIFFERENT SIZES

A model is developed for the sedimentation from a suspension of two particle species of unequal densities and of different sizes. The composition and the thickness of various layers in the sediments are predicted using graphical and analytical methods. The model predictions were in excellent agreement with experimental results, when the particle size ratio was ≥ 108. When size ratio of the particles was 2.60 and 4.31 the agreement occurred in about 50 percent of the cases.     

HEASUREHENT OF INSTANTANEOUS RATES OF LOSS OF VOIATILE COMPOUNDS DURING DRYING OF DROPS

A novel technique serves to monitor instantaneous rates of loss of a volatile solute from a suspended drop during drying. A highly sensitive electron capture detector is used to monitor concentrations of SF6 released into a flowing gas stream from a suspended, drying drop. Simultaneously, the appearance and morphological development of the drop are monitored with a video camera. This provides the wherewithal of relating instantaneous rates of loss of the volatile solute to particular events during the development of particle morphology.

Initial experiments have been carried out with drops of aqueous solutions of glucose, sucrose, maltodextrin and coffee extract. The results clearly display the onset of the volatiles-retentive selective diffusion phenomenon. There is also substantial loss of the volatile component later in the drying process, when the drops undergo repeated ex ansion, bursting and cratering due to the formation of internaf bubbles. These experiments appear to be the first quantitative demonstration of major losses accompanying changes in drop morphology.     

茶多酚提取方法进展

本文综述了国内外现有茶多酚提取方法的现状以及近期的研究进展，并对其优缺点进行了评价。这将有助于中低档茶的综合利用和茶多酚的进一步开发应用。     

ANALYSIS OF RECENT MEASUREMENTS OF THE VISCOSITY OF GLASSES

Viscosity of Simple Soda-Silicate 500° to 1400°C Comparison of the results given by English with those of Washburn, Shelton and Libman, indicates a discrepancy in the absolute values of log₁₀ viscosity amounting to 0.6, those of Washburn et al., being relatively too high. If correction for this is made, the isothermal curves of log₁₀ viscosity as a function of soda content are smooth up to 50% Na₂O, showing no inflection. The observations as a function of temperature T are all represented within accidental error by an equation of the type where all three constants vary regularly with the composition. Change of Viscosity of Glass (6SiO₂, 2Na₂O) due to Molecular Substitution of CaO, MgO and Al₂O₃ for Na₂O The effect is clearly brought out by plotting (from the results of English) the change of log₁₀η due to the substitution as a function of temperature. The curves each show a sharp bend at a temperature between 840° and 1050°C, which is designated the aggregation temperature T_a. If we divide these curves by the corresponding percentage substituted, we get curves for each oxide which are straight and parallel below the aggregation temperatures, the slopes (increase of change of log₁₀η per 100°C) being −0.056 (CaO), −0.055 (MgO), −0.018 (A1₂O₃) per per cent oxide substituted. For substitution of 1/2 molecule the slopes are −0.325 (CaO), −0.23 (MgO) and −0.18 (Al₂O₃) per 100°. At the aggregation temperature the change of log₁₀η per per cent is a minimum, 0.03 to 0.06 for CaO, 0.12 for MgO, 0.07 for Al₂O₃. Evidence of Aggregation in Glasses, from viscosity Measurements The sharp bends in the plots of change of log₁₀η due to substitution of an oxide for Na₂O, suggest the beginning of molecular aggregation at these temperatures. These aggregation temperatures are close to the devitrification temperatures, but the effect on the viscosity curves cannot be due to actual devitrification since it does not change with time. Taking the aggregation temperatures as equal to devitrification temperatures, additional isotherms are roughly sketched into the equilibrium triangle of the system Na₂O-CaO-SiO₂. Change of Viscosity of Glass (4SiO₂, 2Na₂O) due to of Substitution of B₂O₃ for SiO₂ The change of log₁₀η (from the results of English) is plotted as a function of temperature, and also the change of log₁₀η per per cent B₂O₃. The curves are more complex than for the substitution for Na₂O.     

环氧树脂羟基值测定方法的研究

利用乙酸酐、吡啶和浓硫酸混合的乙酰化试剂测定环氧树脂中羟基值含量的方法具有操作简便、滴定终点明显和分析结果误差小等优点。     

骑式摩托车油箱喷涂工艺的改进

面对日益激烈的市场竞争,摩托车油箱外观质量越来越成为影响销售的因素之一。文章介绍了改进工艺后的油箱涂装,该涂装体系提高了油箱外观的丰满度,降低了油箱涂装的生产成本。     

几种针状焦性能对比

针状焦分石油系和煤系两大类,这主要取决于针状焦的原料来源。在同一系列中由于原料不同和工艺条件不同 ,针状焦的各自性能也不相同。针状焦是生产超高功率石墨电极和高功率石墨电极的主要原料 ,针状焦的性能对石墨电极的质量有至关重要的影响。所以对针状焦性能以及其对石墨电极质量影响的研究十分必要的。以下是常用的几种进口针状焦和国产针状焦的性能对比。１原料性能分析对比原料试样包括４种针状焦 ,其中两种为进口针状焦：三菱针状焦和新日化针状焦;另两种为国产针状焦：鞍山针状焦和锦州针状焦。其中除锦州针状焦是石油系针状焦外…     

聚酰亚胺的合成法

本文评述了缩聚型聚酰亚胺的主要合成方法和近年来国际上在合成中所做的探索。