PROPERTIES OF POLYPROPYLENE/NATURAL RUBBER/RECYCLE RUBBER POWDER BLENDS

Thermoplastic elastomers have been prepared by blending polypropylene (PP), natural rubber (NR), and recycle rubber powder (RRP). The blends were melt-mixed using a Brabender Plasticorder torque rheometer at 190°C and 50 rpm. A fixed 70:30 blend ratio (wt%) of PP and rubber was prepared. The effect of partial replacement of NR with RRP at a fixed rubber content (NR+RRP), 30 wt% on mechanical properties, swelling behavior, torque development, and morphological properties of PP/NR/RRP blends was studied. Results show that the tensile strength, Young's modulus, and swelling resistance increase with increasing RRP content in the PP/NR/RRP blends whereas the stabilization torque and elongation at break exhibit opposite trend.     

The Effect of Rice Husk Powder on Standard Malaysian Natural Rubber Grade L (SMR L) and Epoxidized Natural Rubber (ENR 50) Composites

The effects of rice husk powder (RHP) loading and two types of natural rubber matrix (SMR L and ENR 50) on curing characteristics and mechanical properties were studied. The scorch time and cure time decreased with increasing RHP loading whereas maximum torque showed an increasing trend. SMR L composites possessed longer scorch time and cure time than ENR 50 composites. Incorporation of RHP into both rubbers improved tensile modulus significantly but decreased tensile strength and elongation at break. SMR L composites exhibited the lower tensile modulus and higher tensile strength and elongation at break than ENR 50 composites.     

SORPTION,DIFFUSION, AND PERMEATION OF CHLORINATED HYDROCARBON VAPORS THROUGH NATURAL RUBBER,EPOXIDIZED NATURAL RUBBER,AND THEIR BLENDS

The study investigates the transport process of various chlorinated hydrocarbons through natural rubber (NR), epoxidized natural rubber (ENR), and their blends. The effect of structure and morphology of the membranes on the transport parameters has been investigated. Sorption coefficient is found to increase and the permeability coefficient shows the reverse trend with increasing epoxy content. As the mol% epoxidation increases, the polymeric network structure becomes more compact, which leads to a decrease in the diffusion coefficient, which ultimately results in a low permeation coefficient. The morphology of NR/ENR blends has been investigated by combining scanning electron microscopy with permeability measurements. The permeation coefficient is found to be minimum for the NR/ENR 70/30 composition; a 50/50 composition shows the maximum. The heterogeneous morphology of 70/30 NR/ENR blend results in the low permeability coefficient, whereas the co-continuous nature of the 50/50 composition accounts for the maximum permeability. Permeability measurements provide the most useful information about the way morphology is changing with composition of the blends and about the composition corresponding to the maximum level of co-continuity of the two phases.     

The Effect of Filler Loading and Epoxidation on Paper-Sludge-Filled Natural Rubber Composites

The effect of filler loading and epoxidation on curing characteristics, dynamic properties, tensile properties, morphology, and rubber-filler interactions of paper-sludge-filled natural rubber compounds have been studied. Two different types of natural rubber, SMR L and ENR 50, having 0% and 50% of epoxidation and conventional vulcanization were used. Paper sludge was used as a filler and the loading range was from 0 to 40 phr. Compounding was carried out using a laboratory-sized two-roll mill. The scorch time for both rubber compounds decreased with filler loading. The cure time was found to decrease with increasing filler content for SMR L vulcanizates, whereas for ENR 50, the cure time seemed to be independent of the filler loading. Dynamic properties, i.e., maximum elastic torque, viscous torque, and tan delta, increase with filler loading in both grades of natural rubber. Results also indicate that both rubbers show increment in tensile modulus but inverse trend for elongation at break and tensile strength. However, for a fixed filler loading, ENR 50 compounds consistently exhibit higher maximum torque, modulus at 100% elongation, and modulus at 300% elongation, but lower elongation at break than SMR L compounds. In the case of tensile strength, ENR 50 possesses higher tensile strength than SMR L at 10 to 20 phr, but the difference is quite small at 30 and 40 phr. These findings might be associated with better rubber-filler interaction between the polar hydroxyl group of cellulose fiber and the epoxy group of ENR 50.     

Cure and mechanical properties of filled SMR L/ENR 25 and SMR L/SBR blends

The effect of blend ratio of natural rubber/epoxidized natural rubber (SMR L/ENR 25) and natural rubber/styrene‐butadiene rubber (SMR L/SBR) blends on scorch time (t₂), cure time (t₉₀), resilience, hardness, and fatigue properties were studied in the presence of carbon black and silica. An accelerated sulfur vulcanization system was used throughout the investigation. The scorch and cure times of the rubber compound were assessed by using a Moving‐Die Rheometer (MDR 2000). Resilience, hardness, and fatigue life were determined by using a Wallace Dunlop Tripsometer, a Wallace Dead Load Hardness Tester, and a Fatigue to Failure Tester, respectively. The results indicate that t₂ and t₉₀ decrease with increasing ENR 25 composition in the SMR L/ENR 25 blend whereas both values increase with increasing SBR content in the SMR L/SBR blend. This observation is attributed to faster cure in ENR 25 and higher saturation in SBR. Resilience decreases with increase in % ENR and % SBR but hardness shows the reverse behavior in their respective blends. The fatigue life increases with % ENR, but it passes through a maximum with % SBR in the respective blends. In all cases, aging lowers the fatigue life, a phenomenon that is caused by the breakdown of crosslinks in the vulcanizate. Differences in all the observed values between carbon black‐filled and silica‐filled blends are associated with the varying degrees of interaction and dispersion of the two fillers in the rubber blend matrix. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 47–52, 2001     

The Effect of Epoxidized Natural Rubber (ENR-50) or Polyethylene Acrylic Acid (PEA) as Compatibilizer on Properties of Ethylene Vinyl Acetate (EVA)/Natural Rubber (SMR L) Blends

The effect of epoxidized natural rubber (ENR) or polyethylene acrylic acid (PEA) as a compatibilizer on properties of ethylene vinyl acetate (EVA)/natural rubber (SMR L) blends was studied. 5 wt.% of compatibilizer was employed in EVA/SMR L blend and the effect of compatibilizer on tensile properties, thermal properties, swelling resistance, and morphological properties were investigated. Blends were prepared by using a laboratory scale of internal mixer at 120°C with 50 rpm of rotor speed. Tensile properties, thermal properties, thermo-oxidative aging resistance, and oil swell resistance were determined according to related ASTM standards. The compatibility of EVA/SMR L blends with 5 wt.% of compatibilizer addition or without compatibilizing agent was compared. The EVA/SMR L blend with compatibilizer shows substantially improvement in tensile properties compared to the EVA/SMR L blend without compatibilizer. Compatibilization had reduced interfacial tension and domain size of ethylene vinyl acetate (EVA)/natural rubber (SMR L) blends.     

Thermoplastic elastomers-based natural rubber and thermoplastic polyurethane blends

Thermoplastic elastomers based on the blends of thermoplastic polyurethane (TPU) and natural rubber were prepared by a simple blend technique. The influence of the two different types of natural rubber (i.e., unmodified natural rubber (NR) and epoxidized natural rubber (ENR)) on properties of the blends was investigated. The main aim of this study was to improve heat resistance and damping properties, and also to prepare the TPU material with low hardness by blending with various amounts of natural rubber. It was found that the TPU/ENR blends exhibited superior modulus, hardness, shear viscosity, stress relaxation behavior and heat-resistant properties compared to the blends with TPU and unmodified NR. This was attributed to higher chemical interaction between the polar functional groups of ENR and TPU by improving the interfacial adhesion. It was also found that the ENR/TPU blends exhibited finer grain morphology than the blends with unmodified NR. Furthermore, lower tension set, damping factor (Tan ??) and hardness, but higher degradation temperature, were observed in natural rubber/TPU blends compared to pure TPU. This proves the formation of TPU material with high heat resistance, low hardness and better damping properties. However, the blends with higher proportion of natural rubber exhibited lower tensile strength and elongation at break.     

Effect of blend ratio on Mooney scorch time of rubber blends

The Mooney scorch times of three rubber blends [epoxidized natural rubber (ENR) 50/SMR L, ENR 50/styrene butadiene rubber (SBR), and Standard Malaysian Rubber SMR L/SBR] were studied in the temperature range of 120–160°C using an automatic Mooney viscometer. N-Cyclohexyl-2-benzothiazyl sulfenamide was used as the accelerator, and the rubber formulation was based on the conventional vulcanization system. Results for the blends investigated indicate that a negative deviation of scorch time from the interpolated value was observed, especially for temperatures lower than 130°C. This observation was attributed to the induction effect of the ENR 50 in the ENR 50/SMR L and ENR 50/SBR blends to produce more activated precursors to crosslinks, thus enhancing interphase crosslinking. To a lesser extent, SMR L also exhibited such an induction effect in the SMR L/SBR blend. At 120°C, maximum induction effect occurred at around a 40% blend ratio of ENR 50 and SMR L in the respective blends. For the filled stock at 140°C, carbon black exhibited less effect on the scorch property of the blends compared to silica. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1301–1305, 1998     

聚乙烯醇/天然橡胶共混物的制备及其性能研究

利用环氧化天然胶乳作为界面改性剂,采用胶乳共混法将聚乙烯醇（PVA）溶液同天然胶乳进行混溶,制备了PVA/天然橡胶（NR）的共混物,通过电子万能材料试验机、动态热机械分析仪、热老化箱和臭氧老化箱,研究了共混物力学性能、玻璃化转变温度、老化性能以及耐溶剂抽出性。结果表明,PVA的加入明显提高了NR的撕裂强度和硬度,而共混物的拉伸强度和断裂伸长率随着PVA含量的增加都出现下降的趋势;随着PVA含量的增加,NR的玻璃化转变温度呈现先增加后降低的趋势;随着PVA含量增加,共混物各试样对乙醇的耐抽出能力相差不大,对水的耐抽出能力逐步变弱。热空气老化对材料的力学性能影响明显,而臭氧老化由于时间较短,对材料的力学性能影响不明显。老化实验对材料的性能变化率影响显著。     

Modification of PVC/ENR blends by electron beam irradiation

The effects of electron irradiation, with doses ranging from 20 to 100 kGy on the physical properties of poly(vinyl chloride)/epoxidised natural rubber blends (PVC/ENR50 blends) were investigated. The enhancement in tensile strength, elongation at break, hardness, and aging properties of the blends have confirmed the positive effect of irradiation on the blends. Crosslinking of the ENR50 phase proved to play a major role in the improvement of mechanical properties of blends. The results also revealed that at any blend composition the enhancement in properties depends on the irradiation dose which controls the degree of radiation-induced crosslinking. The single glass transition temperature obtained confirms that the blends remain miscible upon irradiation.     

Adhesion properties of pressure-sensitive adhesives prepared from SMR 10/ENR 25, SMR 10/ENR 50, and ENR 25/ENR 50 blends

The adhesion properties, i.e. viscosity, tack, and peel strength of pressure-sensitive adhesives prepared from natural rubber/epoxidized natural rubber blends were investigated using coumarone-indene resin and toluene as the tackifier and solvent respectively. One grade of natural rubber (SMR 10) and two grades of epoxidized natural rubbers (ENR 25 and ENR 50) were used to prepare the rubber blends with blend ratio ranging from 0 to 100%. Coumarone-indene resin content was fixed at 40 parts per hundred parts of rubber (phr) in the adhesive formulation. The viscosity of adhesive was measured by a HAAKE Rotary Viscometer whereas loop tack and peel strength was determined using a Lloyd Adhesion Tester operating at 30 cm/min. Results show that the viscosity of the adhesive passes through a minimum value at 20% blend ratio. For loop tack and peel strength, it indicates a maximum at 60% blend ratio for SMR 10/ENR 25 and SMR 10/ENR 50 systems. However, for ENR 25/ENR 50 blend, maximum value is observed at 80% blend ratio. SMR 10/ENR 25 blend consistently exhibits the best adhesion property in this study, an observation which is attributed to the optimum compatibility between rubbers and wettability of adhesive on the substrate. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical properties,chemical and aging resistance of natural rubber filled with nano‐Al2O3

Al₂O₃ nanoparticles were introduced to natural rubber (NR) to investigate its reinforcement effect on filled NR vulcanizates. The results show that Nano‐Al₂O₃/NR nanocomposites exhibit significantly improved tensile strength, elongation at break, modulus, and tearing strength. Scanning electron microscopy analyses indicate that nanoparticles dispersed in NR matrix at nanoscale and show nano‐reinforcement effect on NR vulcanizates. The aging resistances of filled NR vulcanizates improve. After aging test, tensile strength, tearing strength, and modulus improved, and elongation at break decreased. These attribute to the crosslink maturation reactions, which result in the conversion of polysulfidic linkages into disulfidic and monosulfidic ones. The acid and alkaline resistances of nano‐Al₂O₃‐filled NR vulcanizates improve compared with that of unfilled NR systems. After acid and alkaline test, tensile strength and elongation at break improve, and modulus decrease. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Aspects of miscibility in poly(vinyl chloride)/epoxidized natural rubber blends. Part I: Mechanical and morphological properties

Miscibility in poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends was studied by examining evidence from tensile, impact, and physical properties. The observation of synergism in tensile strength, percent elongation at break, hardness, and relative density has reaffirmed PVC/ENR blends as miscible systems. Studies of impact properties, however, revealed that the blends are microheterogeneous in nature. This could be attributed to the large sizes of polymer molecules involved and the microgel content of ENR-50. Results from Fourier transform infrared spectroscopy (FTIR) revealed that hydrogen bonding is extensively involved in PVC/ENR systems. This evidence unveiled the exact nature of the specific interactions responsible for miscibility and hence the enhanced mechanical properties of PVC/ENR blends.     

天然橡胶／1，2－聚丁二烯共混物在热氧作用下的网络结构分析

用化学应力弛豫法和Ｆｌｏｒｙ交联网络理论分析了在热氧作用下天然橡胶／１，２－聚丁二烯（ＮＲ／１，２－ＰＢ）共混物硫化胶的网络结构特征，并与ＮＲ／丁苯橡胶、ＮＲ硫化胶作了对比，以考察１，２－ＰＢ对ＮＲ／１，２－ＰＢ共混物老化性能的影响。结果表明，１，２－ＰＢ的乙烯基侧基所具有的特殊交联特性，以及在热氧作用下多硫键的重排，是１，２－ＰＢ对ＮＲ改性的主要原因。ＮＲ／１，２－ＰＢ共混比以７５／２５（质量比）时的综合性能最佳。     

Novel ternary blends of natural rubber/linear low-density polyethylene/thermoplastic starch: influence of epoxide level of epoxidized natural rubber on blend properties

Novel degradable materials based on ternary blends of natural rubber (NR)/linear low-density polyethylene (LLDPE)/thermoplastic starch (TPS) were prepared via simple blending technique using three different types of natural rubber (i.e., unmodified natural rubber (RSS#3) and ENR with 25 and 50 mol% epoxide). The evolution of co-continuous phase morphology was first clarified for 50/50: NR/LLDPE blend. Then, 10 wt% of TPS was added to form 50/40/10: NR/LLDPE/TPS ternary blend, where TPS was the particulate dispersed phase in the NR/LLDPE matrix. The smallest TPS particles were observed in the ENR-50/LLDPE blend. This might be attributed to the chemical interactions of polar functional groups in ENR and TPS that enhanced their interfacial adhesion. We found that ternary blend of ENR-50/LLDPE/TPS exhibited higher 100 % modulus, tensile strength, hardness, storage modulus, complex viscosity and thermal properties compared with those of ENR-25/LLDPE/TPS and RSS#3/LLDPE/TPS ternary blends. Furthermore, lower melting temperature (T _m) and heat of crystallization of LLDPE (?H) were observed in ternary blend of ENR-50/LLDPE/TPS compared to the other ternary blends. Also, neat TPS exhibited the fastest biodegradation by weight loss during burial in soil for 2 or 6 months, while the ternary blends of NR/LLDPE/TPS exhibited higher weight loss compared to the neat NR and LLDPE. The lower weight loss of the ternary blends with ENR was likely due to the stronger chemical interfacial interactions. This proved that the blend with ENR had lower biodegradability than the blend with unmodified NR.     

High‐performance bio‐based poly(lactic acid)/natural rubber/epoxidized natural rubber blends: effect of epoxidized natural rubber on microstructure,toughness and static and dynamic mechanical properties

Attempts have been made to prepare high‐performance bio‐based blends through blending of poly(lactic acid) (PLA) with natural rubber (NR) in the presence of epoxidized natural rubber (ENR) as a compatibilizer. The prepared samples were characterized using differential scanning calorimetry, measuring the tensile properties and impact resistance, scanning electron microscopy, Fourier transform infrared (FTIR) spectroscopy and dynamic mechanical analysis (DMTA). Morphological studies revealed a matrix‐dispersed morphology for all blends, in which the average droplet size significantly decreased with the use of ENR. The elongation at break and impact strength of the blend containing 3 wt% ENR were 45 and 16 times those of neat PLA, respectively. These values are significantly higher than those previously reported for various simple and dynamically vulcanized rubber‐toughened PLAs. The influence of ENR on compatibility was confirmed by rheological tests, FTIR spectra and DMTA. DMTA also showed a marked increase in elastic modulus for the blend in the presence of 3 wt% ENR. The tensile properties and impact resistance were directly dependent on the ENR content and rubber droplet size. © 2018 Society of Chemical Industry     

Mechanical properties and blend compatibility of natural rubber –chlorosulfonated polyethylene blends

Natural rubber (NR) was blended with chlorosulfonated polyethylene (CSM) with various formulation and blend ratios (NR/CSM: 80/20 –20/80, wt/wt). Rubber blends were prepared by using a two‐roll mill and vulcanized in a compression mold to obtain the 2 mm‐thick sheets. Tensile properties, tear resistance, thermal aging resistance, ozone resistance, and oil resistance were determined according to ASTM. Compatible NR/CSM blends are derived from certain blends containing 20–30% CSM without adding any compatibilizing agent. Tensile and tear strength of NR‐rich blends for certain formulations show positive deviation from the rule of mixture. Thermal aging resistance depends on formulation and blend ratio, while ozone and oil resistance of the blends increase with CSM content. Homogenizing agents used were Stuktol®60NS and Epoxyprene®25. Stuktol®60NS tends to decrease the mechanical properties of the blends and shows no significant effect on blend morphology. Addition of 5–10 phr of epoxidized natural rubber (ENR, Epoxyprene® 25) increases tensile strength, thermal aging resistance, and ozone resistance of the blends. It is found that ENR acts as a compatibilizer of the NR/CSM blends by decreasing both CSM particle size diameter and α transition temperature of CSM. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 127–140, 2006     

Compatibilization of natural rubber–polyolefin thermoplastic elastomeric blends by phase modification

Natural rubber–polyolefin (70/30) blends have been studied by incorporation of modified rubber and plastic phases with a view to make the heterogeneous phases compatible. The modified rubbers used were epoxidized natural rubber (ENR) and sulfonated ethylene–propylene diene rubber (S-EPDM) at a level of 20 parts. Other rubbers such as chlorinated polyethylene (CPE) and ethylene propylene diene rubbers (EPDM) were also used at a level of 20 parts in the natural rubber–polyethylene (NR/PE) systems. The plastic phase was chemically modified with maleic anhydride (MA) in presence of benzoyl peroxide (BPO) and used at a concentration of 10% of PE, i.e., PEm. The tensile properties such as the modulus, elongation at break, tensile strength, and hysteresis were studied. NR/ENR/PEm/PE shows the greatest improvement in tensile strength (45% over control NR/PE). NR/S-EPDM/PEm/PE also shows similar improvement, although the hysteresis loss decreases. The change in these properties could be related to the adhesive strength. This was found to be improved by the incorporation of modified rubber and modified plastic phases. The best adhesion values have been obtained with NR/ENR/PEm/PE and NR/S-EPDM/PEm/PE. Thus, a correlation between tensile and adhesive strength was obtained for all the systems. The increase in adhesive strength is due to chemical reactions between the various phases. Probable chemical reactions have been suggested. Morphological observations show that the phases are interpenetrating, and this is consistent with the increased tensile strength. The natural rubber–polypropylene (NR/PP) systems do not offer good strength properties with the modified PP and modified rubbers. The adhesive strength also decreases with the incorporation of the modified system. The hysteresis properties show some improvement.     

CURE CHARACTERISTICS AND MECHANICAL PROPERTIES OF NATURAL RUBBER/RECLAIMED RUBBER BLENDS

Cure characteristics and mechanical properties of natural rubber/reclaimed rubber blends were studied. The minimum torque values of the blends were lower than that of the gum compound. The (maximum–minimum torque) and scorch time decreased with increasing reclaim content. The cure rate of the blends were lower than that of the virgin compounds. The tear strength was improved by the addition of reclaimed rubber. Tensile strength, elongation at break, and resilience decreased with increasing reclaim loading. The heat buildup was higher for the blends.     

Effects of cashew nut shell liquid as a plasticizer on cure characteristics,processability, and mechanical properties of 50 : 50 NR/EPDM blends: A comparison with paraffin oil

50 : 50 natural rubber (NR) and ethylene–propylene–diene monomer rubber (EPDM) blends were prepared with different contents of cashew nut shell liquid (CNSL), a natural product obtained from the shells of the cashew nut, as a plasticizer. For comparison, a commercial paraffin oil plasticizer was also used. The effect of plasticizer content on the cure characteristics, processability, and mechanical properties such as tensile strength, elongation at break, and Young's modulus before and after ageing was investigated. Scanning electron microscopy (SEM) was used to observe the blend morphology. The results indicated that the CNSL plasticizer resulted in lower Mooney viscosity and lower cure time of the 50 : 50 NR/EPDM blends. The incorporation of CNSL into 50 : 50 NR/EPDM blends improved tensile strength and elongation at break but decreased Young's modulus. On addition of CNSL the resistance of the blends to heat and weathering ageing improved. Scanning electron micrographs revealed that the morphology of the blend plasticized with CNSL is finer and more homogeneous compared with the blend plasticized with paraffin oil. Overall results indicate that CNSL can be used as a cheaper plasticizer to replace paraffin oil in NR/EPDM blends with improved processability and mechanical properties. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007