Synthesis and properties of fluorinated aromatic poly(amide imide)s based on 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone and various bis(trimellitimide)s

A CF₃‐containing diamine, 4,4′‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzophenone ( 2 ), was synthesized from 4,4′‐dihydroxybenzophenone and 2‐chloro‐5‐nitrobenzotrifluoride. Imide‐containing diacids ( 3 and 5B_a – 5B_g ) were prepared by the condensation reaction of aromatic diamines and trimellitic anhydride. Then, two series of novel soluble aromatic poly(amide imide)s (PAIs; 6A_a – 6A_k and 6B_a – 6B_g ) were synthesized from a diamine ( 4A_a – 4A_k or 2 ) with the imide‐containing diacids ( 3 and 5B_a – 5B_g ) via direct polycondensation with triphenyl phosphate and pyridine. The aromatic PAIs had inherent viscosities of 0.74–1.76 dL/g. All of the synthesized polymers showed excellent solubility in amide‐type solvents, such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide (DMAc), and afforded transparent and tough films by DMAc solvent casting. These polymer films had tensile strengths of 90–113 MPa, elongations at break of 8–15%, and initial moduli of 2.0–2.9 GPa. The glass‐transition temperatures of the aromatic PAIs were in the range 242–279°C. They had 10% weight losses at temperatures above 500°C and showed excellent thermal stabilities. The 6B series exhibited less coloring and showed lower yellowness index values than the corresponding 6A series. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:3641–3653, 2006     

Synthesis and characterization of novel thermally stable and optically active poly(amide‐imide)s derived from N,N′‐(4,4′‐diphthaloyl)‐bis‐L‐leucine diacid and aromatic diamines

A new diacid containing optically active functional groups, N,N′‐(4,4′‐diphthaloyl)‐bis‐L ‐leucine diacid ( 3 ), was synthesized and used in a preparation of a series of poly(amide‐imide)s (PAIs) by direct polycondensation with various aromatic diamines in N‐methyl‐2‐pyrrolidinone (NMP). All polymers derived from diacid ( 3 ) were highly organosoluble in the solvents like N‐methyl‐2‐pyrrolidinone, N,N‐dimethylacetamide, N,N‐dimethylformamide, dimethyl sulfoxide, tetrahydrofuran, γ‐butyrolactone, cyclohexanone, and chloroform at room temperature or upon heating. Inherent viscosities of the PAIs were found to range between 0.34 and 0.61·dL g^?1. All the PAIs afforded flexible and tough films. The glass‐transition temperatures of these PAIs were recorded between 212 and 237°C by differential scanning calorimetry, and the 10% weight loss temperatures were ranging from 372 to 393°C and 336–372°C under nitrogen and air, respectively. The polyimide films had a tensile strength in the range of 63–88 MPa and a tensile modulus in the range of 1.2–1.7 GPa. Optically active PAIs exhibited specific rotations in the range of ?10.58° to ?38.70°. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Novel poly(thiourea‐ether‐imide)s derived from 4,4′‐oxydiphenyl‐bis(thiourea): probing the possibility for high‐temperature applications

Our interest in the fabrication of high‐performance polyimides has led to thiourea‐substituted poly(thiourea‐ether‐imide)s (PTEIs) with good retention of thermal properties along with flame retardancy. A new aromatic monomer, 4,4′‐oxydiphenyl‐bis(thiourea) (ODPBT), was efficiently synthesized and polymerized with various dianhydrides (pyromellitic dianhydride, 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride and 4,4′‐(hexafluoroisopropylidene)diphthalic dianhydride) via two‐stage chemical imidization to fabricate a series of PTEIs. The structural characterization of ODPBT and the polymers was carried out using Fourier transform infrared, ¹H NMR and ¹³C NMR spectral techniques along with crystallinity, organosolubility, inherent viscosity and gel permeation chromatographic measurements. PTEIs bearing C?S and ? O? moieties in the backbone demonstrated an amorphous nature and were readily soluble in various amide solvents. The novel polymers had inherent viscosities of 1.16–1.23 dL g^?1 and molecular weights of ca 90 783–96 927 g mol^?1. Their thermal stability was substantiated via 10% weight loss in the temperature range 516–530 °C under inert atmosphere. The polyimides had glass transition temperatures of 260–265 °C. Incorporation of thiourea functionalities into polymer backbones is demonstrated to be an effective way to enhance their thermal properties and flame retardancy. Thus, ODPBT can be considered as an excellent candidate for use in the synthesis of high‐performance polymeric materials. Copyright © 2010 Society of Chemical Industry     

Synthesis and characterization of novel aromatic polyamides derived from 2,2′‐bis(p‐phenoxyphenyl)‐4, 4′‐diaminodiphenyl ether

BACKGROUND: Wholly aromatic polyamides (aramids) are high‐performance polymeric materials with outstanding heat resistance and excellent chemical stabilities due to chain stiffness and intermolecular hydrogen bonding of amide groups. Synthesis of structurally well‐designed monomers is an effective strategy to prepare modified forms of these aramids to overcome lack of organo‐solubility and processability limitations. RESULTS: A novel class of wholly aromatic polyamides was prepared from a new diamine, namely 2,2′‐bis(p‐phenoxyphenyl)‐4,4′‐diaminodiphenyl ether (PPAPE), and two simple aromatic dicarboxylic acids. Two reference polyamides were also prepared by reacting 4,4′‐diaminodiphenyl ether with the same comonomers under similar conditions. M?_w and M?_n of the resultant polymers were 8.0 × 10⁴ and 5.5 × 10⁴ g mol^?1, respectively. Polymers resulting from PPAPE exhibited a nearly amorphous nature. These polyamides exhibited excellent organo‐solubility in a variety of polar solvents and possessed glass transition temperatures up to 200 °C. The 10% weight loss temperatures of these polymers were found to be up to 500 °C under a nitrogen atmosphere. The polymers obtained from PPAPE could be cast into transparent and flexible films from N,N‐dimethylacetamide solution. CONCLUSION: The results obtained show that the new PPAPE diamine can be considered as a good monomer to enhance the processability of its resultant aromatic polyamides while maintaining their high thermal stability. The observed characteristics of the polyamides obtained make them promising high‐performance polymeric materials. Copyright © 2009 Society of Chemical Industry     

Highly fluorinated poly(ether‐imide)s derived from 2,2′‐bis(3,4,5‐trifluorophenyl)‐4,4′‐diaminodiphenyl ether and aromatic dianhydrides

A new diamine, 2,2′‐bis(3,4,5‐trifluorophenyl)‐4,4′‐diaminodiphenyl ether (FPAPE) was synthesized through the Suzuki coupling reaction of 2,2′‐diiodo‐4,4′‐dinitrodiphenyl ether with 3,4,5‐trifluorophenylboronic acid to produce 2,2′‐bis(3,4,5‐trifluorophenyl)‐4,4′‐dinitrodiphenyl ether (FPNPE), followed by palladium‐catalyzed hydrazine reduction of FPNPE. FPAPE was then utilized to prepare a novel class of highly fluorinated all‐aromatic poly(ether‐imide)s. The chemical structure of the resulting polymers is well confirmed by infrared and nuclear magnetic resonance spectroscopic methods. Limiting viscosity numbers of the polymer solutions at 25 °C were measured through the extrapolation of the concentrations used to zero. M_n and M_w of these polymers were about 10 000 and 25 000 g mol^?1, respectively. The polymers showed a good film‐forming ability, and some characteristics of their thin films including color and flexibility were investigated qualitatively. An excellent solubility in polar organic solvents was observed. X‐ray diffraction measurements showed that the fluoro‐containing polymers have a nearly amorphous nature. The resulting polymers had T_g values higher than 340 °C and were thermally stable, with 10% weight loss temperatures being recorded above 550 °C. Based on the results obtained, FPAPE can be considered as a promising design to prepare the related high performance polymeric materials. Copyright © 2011 Society of Chemical Industry     

Synthesis and properties of poly(arylene ether)s based on 3‐pentadecyl 4,4'‐biphenol

A new biphenol, 3‐pentadecyl 4,4′‐biphenol, was synthesized starting from 3‐pentadecylphenol and was polycondensed with 4,4′‐difluorobenzophenone, 1,3‐bis(4‐fluorobenzoyl)benzene and bis(4‐fluorophenyl)sulfone to obtain poly(arylene ether)s with biphenylene linkages in the backbone and pendent pentadecyl chains. Inherent viscosities and number‐average molecular weights (M_n) of the poly(arylene ether)s were in the range 0.50 ? 0.81 dL g^?1 and 2.2 × 10⁴ ? 8.3 × 10⁴, respectively. Detailed NMR spectroscopic studies of the poly(arylene ether)s indicated the presence of constitutional isomerism which existed because of the non‐symmetrical structure of 3‐pentadecyl 4,4′‐biphenol. The poly(arylene ether)s readily dissolved in common organic solvents such as dichloromethane, chloroform and tetrahydrofuran and could be cast into tough, transparent and flexible films from their chloroform solutions. The poly(arylene ether)s exhibited T_g values in the range 35–60 °C which are lower than that of reference poly(arylene ether)s without pentadecyl chains. The 10% decomposition temperatures (T₁₀) of the poly(arylene ether)s were in the range 410–455 °C indicating their good thermal stability. A gas permeation study of poly(ether sulfone) containing pendent pentadecyl chains revealed a moderate increase in permeability for helium, hydrogen and oxygen. However, there was a large increase in permeability for carbon dioxide which could be attributed to the internal plasticization effect of pendent pentadecyl chains. © 2016 Society of Chemical Industry     

Synthesis and characterization of new soluble poly(ester‐imide)s containing noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit

A new diimide–diacid chloride (3) containing a noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit was synthesized by treating 2,2′‐dimethyl‐4,4′‐diamino‐biphenylene with trimellitic anhydride followed by refluxing with thionyl chloride. Various new poly(ester‐imide)s were prepared from 3 with different bisphenols by solution polycondensation in nitrobenzene using pyridine as hydrogen chloride quencher at 170°C. Inherent viscosities of the poly(ester‐imide)s were found to range between 0.31 and 0.35 dL g^?1. All of the poly(ester‐imide)s, except the one containing pendent adamantyl group 5e, exhibited excellent solubility in the following solvents: N,N‐dimethylformamide, tetrahydrofuran, tetrachloroethane, dimethyl sulfoxide, N,N‐dimethylacetamide, N‐methyl‐2‐pyrrolidinone, m‐cresol, o‐chlorophenol, and chloroform. The polymers showed glass‐transition temperatures between 166 and 226°C. The 10% weight loss temperatures of the poly(ester‐imide)s, measured by TGA, were found to be in the range between 415 and 456°C in nitrogen. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2486–2493, 2004     

Flexible aliphatic poly(isocyanurate–oxazolidone) resins based on poly(ethylene glycol) diglycidyl ether and 4,4′‐methylene dicyclohexyl diisocyanate

New flexible aliphatic oxazolidone‐isocyanurate networks (AISOX) are obtained by reacting a low molecular weight diisocyanate (4,4′‐methylene dicyclohexyl diisocyanate, H₁₂MDI) and a macro‐diepoxyde (poly(ethylene glycol) diglycidyl ether, M_n = 526, PEGDGE) in different molar ratio. The curing reaction, carried out from 25 °C to 200 °C, is studied by using DSC and FTIR. The effect of the molar ratio of the two monomers on thermal and mechanical properties of AISOX resins is investigated by DSC, thermogravimetric analysis, stress?strain measurements and optical microscopy. Independently from the feed composition, it is observed that the reaction steps are: (i) partial hydrolysis of isocyanate caused by water traces, (ii) incomplete trimerization of isocyanate to give isocyanurate, and (iii) formation of oxazolidone and complete conversion of isocyanate. At the highest concentration of the soft macrodiepoxyde (PEGDGE), the AISOX resin is in the rubbery state at room temperature and shows an elastomeric behavior. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43404.     

An NMR study of the dissociation of N,N′-(2-propyloximino)-4,4′-methylenebis(phenylcarbamate) and its crosslinking of polymers containing labile hydrogens. II

Nuclear magnetic resonance spectroscopy has been used to study the dissociation and reaction of N,N′-(2-propyloximino)-4,4′-methylenebis(phenylcarbamate), as a crosslinking agent for polymers containing labile hydrogens. The crosslinking of poly(acrylic acid), polyacrylamide, and poly(vinyl alcohol) was found to result upon heating each to 150°C for 10 min with this component at 2–10 wt %.     

New poly(amide imide imide)s based on tetraimide dicarboxylic acid condensed from 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride,m‐aminobenzoic acid,and 4,4″‐oxydianiline and various aromatic diamines

A series of new, organosoluble, and light‐colored poly(amide imide imide)s were synthesized from tetraimide dicarboxylic acid ( I ) and various aromatic diamines by direct polycondensation with triphenyl phosphite and pyridine as condensing agents. I was prepared by the azeotropic condensation of 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride, m‐aminobenzoic acid, and 4,4′‐oxydianiline at a 2/2/1 molar ratio in N‐methyl‐2‐pyrrolidone (NMP)/toluene. The thin films cast from N,N‐dimethylacetamide (DMAc) had cutoff wavelengths shorter than 400 nm (365–394 nm) and color coordinate b* values between 13.10 and 36.07; these polymers were lighter in color than the analogous poly(amide imide)s and isomeric polymers. All of the polymers were readily soluble in a variety of organic solvents, including NMP, DMAc, N,N‐dimethylformamide, dimethyl sulfoxide, and even less polar dioxane and tetrahydrofuran. The cast films exhibited tensile strengths of 90–104 MPa, elongations at break of 7–22%, and initial moduli of 1.9–2.4 GPa. The glass‐transition temperatures of the polymers were recorded at 274–319°C. They had 10% weight losses at temperatures beyond 520°C and left more than a 50% residue even at 800°C in nitrogen. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 669–679, 2003     

One-step synthesis of aromatic polyimides based on 4,4′-diaminotriphenylmethane

The feasibility of using a one-step high-temperature polycondensation for the synthesis of aromatic polyimides, based on 4,4′-diaminotriphenylmethane (DA-TPM), was studied. It was found that the reaction of DA-TPM with various aromatic dianhydrides in nitrobenzene at 180–200°C resulted in the formation of the high molecular weight soluble polyimides, PI-TPM. The reaction solutions cooled to ambient temperature were used for casting films. These PI-TPM films significantly exceeded their prototypes obtained by the thermal imidization of poly(amic acids) in terms of solubility and tensile properties. All studied polyimides demonstrated well-distinguished glass transition at 260–320°C. © 1996 John Wiley & Sons, Inc.     

Isothermal Cure of an Epoxy System Containing Tetraglycidyl-4,4′-diaminodiphenylmethane (TGDDM), a Multifunctional Novolac Glycidyl Ether and 4,4′-Diaminodiphenylsulphone (DDS): Vitrification and Gelation

Times to gelation and vitrification have been determined at different isothermal curing temperatures between 200 and 240°C for an epoxy/amine system containing both tetraglycidyl-4,4′-diaminodiphenylmethane (TGDDM) and a multifunctional Novolac glycidyl ether with 4,4′-diaminodiphenylsulphone (DDS). The mixture was rich in epoxy, with an amine/epoxide ratio of 0·64. Gelation occurred around 44% conversion. Vitrification was determined from data curves of glass transition temperature, T_g, versus curing time obtained from differential scanning calorimetry experiments. The minimum and maximum values T_g determined for this epoxy system were T_g0=12°C and T_gmax=242°C. Values of activation energy for the cure reaction were obtained from T_g versus time shift factors, a_T, and gel time measurements. These values were, respectively, 76·2kJmol^-1 and 61·0kJmol^-1. The isothermal time–temperature–transformation (TTT) diagram for this system has been established. Vitrification and gelation curves cross at a cure temperature of 102°C, which corresponds to glass transition temperature of the gel. © of SCI.     

Synthesis and properties of organosoluble poly(ether imide)s containing 4,4′(octahydro-4,7-methano-5H-inden-5-ylidene) cardo group

A series of organosoluble aromatic poly(ether imide)s (PEIs) VIIa-k were synthesized from 4,4′-[(octahydro-4,7-methano-5H-inden-5-ylidene)bis(1,4-phenylene)dioxy] diphthalic dianhydride (IV) and various aromatic diamines. PEIs synthesized through two-stage polymerization had inherent viscosities of 0.51–0.64 dL/g. This series of polymers could also be synthesized from IV and diamines in a small amount of refluxing m-cresol in a one-step process and had inherent viscosities of 0.65–0.87 dL/g. For the low melting point diamines (Vj and Vk), polymers could be obtained by bulk polymerization and had inherent viscosities of 0.36 and 0.41 dL/g. Polymers showed good organosolubility and could be cast into transparent, flexible, and tough polyimide films with good tensile properties. These PEIs had glass transition temperatures among 203–281°C. Thermogravimetric analyses established that these polymers were fairly stable up to 430°C, and the 10% weight loss temperatures were recorded in the range of 473–503°C in nitrogen and 481–512°C in air atmosphere. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 987–996, 1999     

Poly(vinyl chloride)–polyol (AB)x block copolymers: Synthesis,characterization, and mechanical properties

Poly(vinyl chloride)–polyol (AB)_x block copolymers have been prepared by the condensation polymerization of low-molecular-weight hydroxy-terminated poly(vinyl chlorides) (PVC) and diisocyanate-capped polyester and polyether diols. The difunctional poly(vinyl chlorides) were synthesized by ozonization of commercial resin followed by metal hydride reduction. The (AB)_x block copolymers, which contained 3000 or 4300 molecular weight PVC block sizes and 1000–2000 molecular weight polyol segments, had a wide range of mechanical properties, depending on overall polymer structure. Tensile strengths ranged from 7.8 to 31.5 MPa, elongations from 125% to 610% and torsional stiffness temperatures (T_f) from 25°C to ?22°C.     

Ambipolar and multi‐electrochromic polyimides based on N,N‐di(4‐aminophenyl)‐N′,N′‐diphenyl‐4,4′‐oxydianiline

A series of novel aromatic polyimides were synthesized from N,N‐di(4‐aminophenyl)‐N′,N′‐diphenyl‐4,4′‐oxydianiline and aromatic tetracarboxylic dianhydrides through a conventional two‐step procedure. Most of the polyimides exhibited reasonable solubility in organic solvents and could afford robust films via solution casting. The polyimides exhibited high thermal stability, with glass transition temperatures in the range 227–273 °C and 10% weight‐loss temperatures in excess of 550 °C. All the polyimide films showed ambipolar redox and multi‐electrochromic behaviors. They exhibited two reversible oxidation redox couples at 0.94–0.98 and 1.09–1.12 V versus Ag/AgCl in acetonitrile solution. A coupling reaction between the radical cations of the pendent triphenylamine units occurred during the oxidative process forming a tetraphenylbenzidine structure which resulted in an additional redox state and color change. © 2014 Society of Chemical Industry     

Preparation of high‐molecular‐weight poly(vinyl alcohol) with high yield by solution polymerization of vinyl acetate in methanol using 4,4′‐azobis(4‐cyanovaleric acid)

Vinyl acetate (VAc) was solution‐polymerized at 40°C and 50°C using 4,4′‐azobis(4‐cyanovaleric acid) (ACVA) as an initiator and methanol as a solvent, and effects of polymerization temperature and initiator concentration were investigated in terms of conversion of VAc into poly (vinyl acetate) (PVAc), degree of branching (DB) for acetyl group of PVAc, and molecular weights of PVAc and resulting poly(vinyl alcohol) (PVA) obtained by saponifying with sodium hydroxide. Slower polymerization rate by adopting ACVA and lower viscosity by methanol proved to be efficient in obtaining linear high‐molecular‐weight (HMW) PVAc with high conversion and HMW PVA. PVA having maximum number–average degree of polymerization (P_n) of 4300 could be prepared by the saponification of PVAc having maximum P_n of 7900 polymerized using ACVA concentration of 2 × 10^?5 mol/mol of VAc at 40°C. Moreover, low DB of below 1 could be obtained in ACVA system, nevertheless of general polymerization temperatures of 40°C and 50°C. This suggests an easy way for producing HMW PVA with high yield by conventional solution polymerization without using special methods such as low‐temperature cooling or irradiation. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 4831–4834, 2006     

Preparation and properties of 4,4′‐(hexafluoroisopropylidene) diphenol cured 2,2‐bis(4‐cyanatophenyl) propane

A novel easily curing system of 2,2‐bis(4‐cyanatophenyl) propane(BACY) was prepared by employing 4,4′‐(Hexafluoroisopropylidene) Diphenol (BPAF) as modifier. The curing efficiency of BPAF was evaluated by means of differential scanning calorimetry (DSC) and Fourier translation infrared spectroscopy analysis (FTIR). It was found that the exothermic peak temperature (T_p) was 168 °C when the content of BPAF/BACY was 15/85 by weight, while the temperature of BACY was 215 °C under the same conditions when trace of cobalt(III) acetylacetonate(CoAt(III)) was added. Besides, BPAF/BACY system owned outstanding properties including excellent curing characteristics, high shear strength, remarkable dielectric properties and high thermal stability in contrast to BACY, 4,4′‐(1‐methylethylidene) bisphenol(BPA)/BACY, and nonylphenol(NoP)/BACY systems. Moreover, the properties of cured BPAF/BACY modified by different proportions of BPAF were studied in detail. It was shown that moderate BPAF was conducive to most properties of polycyanurate, and the optimal proportion of BPAF/BACY was 15/85 by weight. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44518.     

Synthesis and characterization of new thermally stable poly(ester‐imide)s derived from 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl and various aromatic dihydroxy compounds

A series of new alternating aromatic poly(ester‐imide)s were prepared by the polycondensation of the preformed imide ring‐containing diacids, 2,2′‐bis(4‐trimellitimidophenoxy)biphenyl (2a) and 2,2′‐bis(4‐trimellitimidophenoxy)‐1,1′‐binaphthyl (2b) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. A model compound (3) was also prepared by the reaction of 2b with phenol, its synthesis permitting an optimization of polymerization conditions. Poly(ester‐imides) were fully characterized by FTIR, UV‐vis and NMR spectroscopy. Both biphenylene‐ and binaphthylene‐based poly(ester‐imide)s exhibited excellent solubility in common organic solvents such as tetrahydrofuran, m‐cresol, pyridine and dichloromethane. However, binaphthylene‐based poly(ester‐imide)s were more soluble than those of biphenylene‐based polymers in highly polar organic solvents, including N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide and dimethyl sulfoxide. From differential scanning calorimetry thermograms, the polymers showed glass‐transition temperatures between 261 and 315 °C. Thermal behaviour of the polymers obtained was characterized by thermogravimetric analysis, and the 10 % weight loss temperatures of the poly(ester‐imide)s was in the range 449–491 °C in nitrogen. Furthermore, crystallinity of the polymers was estimated by means of wide‐angle X‐ray diffraction. The resultant poly(ester‐imide)s exhibited nearly an amorphous nature, except poly(ester‐imide)s derived from hydroquinone and 4,4′‐dihydroxybiphenyl. In general, polymers containing binaphthyl units showed higher thermal stability but lower crystallinity than polymers containing biphenyl units. Copyright © 2005 Society of Chemical Industry     

Synthesis and characterization of aromatic/cycloaliphatic poly(amide‐ imide‐imide)s from bis(4‐amino‐ 3,5‐dimethylphenyl) cycloalkane derivatives

A series of novel aromatic diamines containing cycloaliphatic moieties was synthesized by the reaction of cycloalkanones like cyclohexanone and cycloheptanone with 2,6‐dimethylaniline. The tetrimide diacid was synthesized using the prepared diamine with 3,3′,4,4′‐benzophenonetetracarboxylic acid dianhydride/pyromellitic dianhydride and p‐aminobenzoic acid. The polymers were prepared by treating the tetrimide diacid with different aromatic diamines. The structures of the monomers and polymers were identified using elemental analysis and Fourier transform infrared, ¹H NMR and ¹³C NMR spectroscopy. The polymers show excellent solubility. The polymers are amorphous and have high optical transparency. They also show good thermal stability and their T_g value is found to be in the range 268–305 °C. Copyright © 2007 Society of Chemical Industry     

Sequence analysis and fiber properties of a blend of poly(ethylene terephthalate) and poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)

Blends of poly(ethylene terephthalate) (PET) and poly(ethylene terephthalate‐co‐4,4′‐ bibenzoate) (PETBB) are prepared by coextrusion. Analysis by ¹³C‐NMR spectroscopy shows that little transesterification occurs during the blending process. Additional heat treatment of the blend leads to more transesterification and a corresponding increase in the degree of randomness, R. Analysis by differential scanning calorimetry shows that the as‐extruded blend is semicrystalline, unlike PETBB15, a random copolymer with the same composition as the non‐ random blend. Additional heat treatment of the blend leads to a decrease in the melting point, T_m, and an increase in glass transition temperature, T_g. The T_m and T_g of the blend reach minimum and maximum values, respectively, after 15 min at 270°C, at which point the blend has not been fully randomized. The blend has a lower crystallization rate than PET and PETBB55 (a copolymer containing 55 mol % bibenzoate). The PET/PETBB55 (70/30 w/w) blend shows a secondary endothermic peak at 15°C above an isothermal crystallization temperature. The secondary peak was confirmed to be the melting of small and/or imperfect crystals resulting from secondary crystallization. The blend exhibits the crystal structure of PET. Tensile properties of the fibers prepared from the blend are comparable to those of PET fiber, whereas PETBB55 fibers display higher performance. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1793–1803, 2004