Polymers from renewable sources. III. Hydroxy-terminated myrcene polymers

A range of hydroxy-terminated polymyrcenes has been prepared using hydrogen peroxide initiated polymerization of pyroysate grade, β-myrcene in n-butanol solution at 100°C. An oligomeric fraction, containing a large proportion of dimeric material formed via the Diels–Alder reaction, always accompanies the major polymeric fraction. Procedures are described for the removal of this oligomeric material. Polyols so prepared and purified had number average molecular weights (M _n) between 4000 and 2000 g mol^?1 at low and high initiator concentrations, respectively, with corresponding number average functionalities (f _n) between 1.3 and 2.3 and polydispersities (M _w/M _n) of ～1.3. The microstructure of the polyols was investigated using NMR spectroscopy from which the main mode of propagation during polymerization of myrcene was deduced to be 1,4 addition across the conjugated double bonds. Glass transition temperatures of the polymyrcenes measured by differential scanning calorimetry were in the range ?50–60°C.     

Intrinsic viscosity–number average molecular weight relationship for poly(1,4‐butylene adipate) diol

The relationship between number average molecular weight (M_n) and intrinsic viscosity ([η]) was studied for poly(1,4‐butylene adipate) diol (PBAD) in tetrahydrofuran, toluene, and ethyl acetate at 25°C. Thus, a series of PBAD samples were prepared by polymerization between 1,6‐adipic acid and 1,4‐butanediol. The values of M_n for the samples were determined by end‐group analysis as well as by ebulliometry, and the average difference of M_n between the two analysis ways was about 2.69%. The Mark–Houwink–Sakurada equations for PBAD were obtained to relate [η] with M_n in the range of 1900–10,000. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Ultrasound devulcanization of unfilled natural rubber networks,studied via component molecular mobility

¹³C NMR solids spectroscopy and transverse relaxation, and ¹H relaxation and pulsed‐gradient spin‐echo self‐diffusion measurements at 70 °C were used to study molecular and segmental mobilities in natural rubber before and after sulfur crosslinking, and after subsequent devulcanization using intense ultrasound. NMR relaxation does not clearly distinguish between entangled and crosslinked network mobility, but unentangled sol and oligomeric species are separable within the longer T₂ decay components. Ultrasound reactor settings affect the amount of extractable sol generated. Some two‐thirds of the sol is entangled, with number‐average molecular weights (M_n) above 10 000 g mol^?1. Samples also contain near 2 wt% of inert light species (M_n < 400 g mol^?1); ultrasound is relatively ineffective in producing additional oligomeric material. All proton mobilities increase as more sol is produced, but ¹³C relaxation, reflecting intramolecular effects, indicates a slight decrease in backbone mobility. In contrast with other rubbers, in natural rubber, neither the glass transition nor the sol diffusion rate is greatly affected by the extent of ultrasound exposure. Comparisons with previous similar work of this laboratory, particularly styrene‐butadiene rubber, are useful in confirming the molecular mechanisms involved. Copyright © 2007 Society of Chemical Industry     

Polymerization of acrylamide and methacrylamide initiated by a potassium peroxydiphosphate/Mn(II) system

The kinetics of aqueous polymerization of acrylamide (AM) and methacrylamide (MAM) have been studied using a potassium peroxydiphosphate (PDP/Mn(II) system in an inert atmosphere at 40°C and at constant pH (1·30). The polymerization rate R_p has been found to be proportional to the half power of PDP and Mn(II) concentrations. The overall energy of activation (ΔE) was found to be 40·2±0·1kJmol^-1 and 45·0±0.1kJmol^-1 for AM and MAM, respectively. Intrinsic viscosity [η], viscometric average molecular weight (M_v) and number average degree of polymerization (P_n) at different concentrations of PDP, Mn(II) and monomer are reported. © 1998 SCI.     

Kinetics of atom transfer radical polymerization of crosslinkable terpolymer P(MMA‐BA‐HEMA)

A crosslinkable terpolymer P(MMA‐BA‐HEMA) was prepared by atom transfer radical copolymerization of 2‐hydroxyethyl methacrylate, methyl methacrylate and butyl acrylate. The structure of the terpolymer was characterized by ¹H NMR and gel permeation chromatography. The effects on the polymerization of ligand, initiator, solvent, CuCl₂ added in the initial stage and reaction temperature were investigated. The optimal reaction conditions were ethyl 2‐bromopropionate as initiator, CuCl/PMDETA as catalyst, cyclohexanone as solvent, catalyst/ligand = 1:1.5, [M]₀:[I]₀ = 200:1 and temperature 70 °C. The reaction followed first‐order kinetics with respect to monomer concentration, indicating the best control over the polymerization process, a constant concentration of the propagating radical during the polymerization, efficient control over M_n of the polymer and low polydispersity (M_w/M_n < 1.3). © 2013 Society of Chemical Industry     

Synthesis of poly(1‐hexene)s end‐functionalized with phenols

Electrophilic alkylations of phenol/2,6‐dimethylphenol were performed with vinylidene‐terminated poly(1‐hexene)s using BF₃·OEt₂ catalyst. Vinylidene‐terminated poly(1‐hexene)s with M_n varying from 400 to 10000 were prepared by bulk polymerization of 1‐hexene at 50 to ?20 °C using Cp₂ZrCl₂/MAO catalysts. The phenol/2,6‐dimethylphenol‐terminated poly(1‐hexene)s was characterized by NMR (¹H, ¹³C), UV, IR and vapor phase osmometer (VPO). The isomer distribution (ortho, para and ortho/para) was determined by ¹³P NMR using a phosphitylating reagent, namely 2‐chloro‐1,3,2‐dioxaphospholane. The number‐average degree of functionality (F_n) >0.9 with >95% para selectivity could be achieved using low‐molecular‐weight oligomers of poly(1‐hexene)s. Copyright © 2005 Society of Chemical Industry     

Radical polymerization of fumaramide and fumaramate derivatives for homogeneous Langmuir monolayers

Summary The radical polymerization of a series of fumaramides and fumaramates, prepared from the reaction of various amines with fumaroyl dichloride and fumaric chloride isopropyl ester, respectively, was investigated. Although the polymerization reactivity of the N,N,N’,N’-tetrasubstituted fumaramides and N,N-disubstituted fumaramates was low, N-isopropyl fumaramate readily furnished the corresponding high molecular weight polymer. The highest number average molecular weight (M_n) of 15,400 was obtained from the emulsifier-free emulsion polymerization in the presence of VA-086 as the initiator. The decomposition temperature of the obtained polymer was determined to be 299 °C. The π-A isotherm of the polymer indicated the formation of stable Langmuir monolayers with a limiting molecular area (per macromolecular repeating unit) of ca. 26 ?².     

In-chain functionalization by alternating anionic copolymerization of styrene and 1-(4-dimethylaminophenyl)-1-phenylethylene

Anionic copolymerizations of styrene (M₁) with excess 1-(4-dimethyl-aminophenyl)-1-phenylethylene (M₂) were conducted in benzene at 25°C for 24h, using sec-butyllithium as initiator. Narrow molecular weight distribution copolymers with M?;_n = 16.1 × 10³ g/mol (M?_w/M?_n = 1.04) and 38.2 × 10³g/mol (M?_w/M?_n = 1.05), and 24 and 38 moles of M₂ per macromolecule, respectively, were characterized by size exclusion chromatography, ¹H NMR spectroscopy and DSC. The monomer reactivity ratio, r₁ = 5.6, was obtained from the copolymer composition at complete consumption of M₁, assuming that the rate constant k₂₂ =0,i.e. r₂ =0. The polymers exhibited T_g values of 128 and 119°C, respectively, which correspond to an estimated T_g = 217°C for the hypothetical homopolymer of M₂.     

‘Living’ radical polymerization of styrene with AIBN/FeCl3/PPh3 initiating system via a reverse atom transfer radical polymerization process

Well‐defined polystyrenes with an α‐C(CH₃)₂(CN) and an ω‐chlorine atom end‐groups, and narrow polydispersity (M_n = 3000–4000 g mol⁻¹, M_w/M_n = 1.3–1.4) have been synthesized by a radical polymerization process using 2,2′‐azobisisobutyronitrile(AIBN)/FeCl₃/PPh₃ initiation system. When the ratio of [St]₀:[AIBN]₀:[FeCl₃]₀:[PPh₃]₀ is 200:1:4:12 at 110 °C, the radical polymerization is ‘living’, but the molecular weight of the polymers is not well‐controlled. The polymerization mechanism belongs to a reverse atom transfer radical polymerization (ATRP). Because the polymer obtained is end‐functionalized by a chlorine atom, it can then be used as a macroinitiator to perform a chain extension polymerization in the presence of CuCl/2,2′‐bipyridine catalyst system via a conventional ATRP process. The presence of a chlorine atom as an end‐group was determined by ¹H NMR spectroscopy. © 2000 Society of Chemical Industry     

Cooking schedule of alkyd resin preparation. I. Effect of cooking schedule on viscosity-molecular weight relationship

The two constants in the equation log η = A + C′ M?_n^1/2 (η is the viscosity of molten alkyd and M?_n the number average molecular weight) were determined at 110°C for two kinds of alkyd resin prepared with the same formulation but with different cooking schedules. It was found that the magnitude of the slope C′ was larger for the alkyd which was prepared by raising the reaction temperature directly up to 230°C, in comparison with that of the alkyd which was prepared by maintaining the temperature at 170°C for an hour and then raising it up to 230°C. Measurements of η and M?_n were carried out until the gelation occurred. Both upward and downward breaks were observed in log η vs. M?_n^1/2 plot. Based on these viscometric data, the gel point mechanism was discussed. Disagreements between the molecular weight observed and that calculated from the Flory's theoretical equation became more remarkable as the esterification proceeded. This suggested that a large extent of intraesterification reaction is taking place in alkyd synthesis.     

Polymerization of acrylonitrile catalyzed by thiolate complexes of divalent and trivalent lanthanoids

Arenethiolate complexes of lanthanoid(II) and lanthanoid(III) metals were used as initiators for the polymerization of acrylonitrile at −78 °C in THF, giving atactic and high molecular mass (M_n ≈ 10⁵) polyacrylonitriles in good yield. © 1999 Society of Chemical Industry     

Trimethylsilyl‐substituted triazole‐based ligand for copper‐mediated single‐electron transfer living radical polymerization of methyl methacrylate

The tripodal ‘click’ compound tris(4‐trimethylsilylmethyl‐1,2,3‐triazolylmethyl)amine (TTTA) was prepared and investigated as a ligand for copper‐catalysed single‐electron transfer living radical polymerization of methyl methacrylate (MMA). Bulk polymerizations catalysed by Cu⁰/CuBr₂/TTTA with a molar ratio of [MMA]₀/[ethyl‐2‐bromoisobutyrate]₀/[CuBr₂]₀/[TTTA]₀ = 200:2:1:1 and a 1.0 × 1.0 cm² Cu⁰ sheet were fast and well controlled (76% conversion with M_w/M_n = 1.19 after 3.5 h). Greater amounts of added air generally gave slower polymerizations although M_w/M_n remained low (<1.3) even when the polymerization was carried out under aerobic conditions. Decreasing initial concentrations of the Cu⁰/CuBr₂/TTTA catalyst system or polymerization temperatures also resulted in slower polymerizations and yielded polymers with broader dispersity. Kinetic studies in the temperature range 40–90 °C revealed an apparent activation energy of 22.6 kJ mol^?1. © 2014 Society of Chemical Industry     

Formation of monodisperse polyacrylamide particles by radiation‐induced dispersion polymerization. I. Synthesis and polymerization kinetics

Highly monodisperse polyacrylamide (PAM) microparticles were directly prepared by radiation‐induced dispersion polymerization at room temperature in an aqueous alcohol media using poly(N‐vinylpyrrolidone) (PVP) as a steric stabilizer. Monomer conversion was studied dilatometrically and polymer molecular weight was determined viscometrically. The gel effect was found evidently from the polymerization kinetics curves. The influence of the dose rate, monomer concentration, stabilizer content, medium polarity, polymerization temperature on the polymerization rate, and the molecular weight of the polymer was examined. The polymerization rate (Rp) can be represented by Rp ∝ D^0.15[M]^0.86[S]^0.47[A/W]^0.64 and the molecular weight of the polymer can be represented by M_w ∝ D^?0.19 [M]^1.71[S]^0.43[A/W]^0.14 at a definite experimental variation range. The overall activation energy for the rate of polymerization is 10.57 kJ/mol (20–35°C). Based on these experimental results, the polymerization mechanisms were discussed primarily. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2567–2573, 2002     

Polyurethanes from 4,4′‐diphenylmethane diisocyanate and poly(ethylene glycol)s. II. Crystallographic data,heats of melting and crystallization,thermal stability,crystallinity and density

Wide‐angle X‐ray scattering analysis, heats of melting, crystallization and re‐melting, thermogravimetric analysis and density measurements have been used to study the crystallographic data and degree of crystallinity of linear polyurethanes (PUs) prepared by the polymerization of 4,4′‐diphenylmethane diisocyanate (MDI) with poly(ethylene glycol)s (PEGs) of various number‐average molecular weights (M_ns) (106, 200, 400, 1000, 2000 and 4000 g mol^?1) in equivalent molar ratios. The crystallinities of polyurethanes PU1000 to PU4000 are shown to be due to the polyoxyethylene segments of the PEGs, while PU400 and PU200 appeared to be amorphous. However, PU106, similarly prepared from diethylene glycol (PEG106), is highly crystalline with a different crystal structure. Thermogravimetric analysis of PU106, PU400 and PU1000 exhibited high thermal stabilities up to 260 °C for these materials under the conditions of measurement (10 °C min^?1). The heat of melting for the 100 % crystalline structure of PU106 has been indirectly obtained. Copyright © 2004 Society of Chemical Industry     

Formation of a soluble hyperbranched polymer via initiator–fragment incorporation radical copolymerization of divinyl adipate and isobutyl vinyl ether

The copolymerization of divinyl adipate (DVA) with isobutyl vinyl ether (IBVE) was conducted at 70 and 80 °C in benzene using azobisisobutyronitrile (AIBN), at a concentration as high as 0.50 mol l^?1 as the initiator, where the concentrations of DVA and IBVE were 0.40 and 0.60 mol l^?1, respectively. The copolymerization proceeded homogeneously, without any gelation, to yield soluble copolymers in spite of the high molar ratio of DVA as an excellent cross‐linker for IBVE. The copolymer yield increased with time, and the number‐average molecular weight (M_n = 0.9–2.4 × 10⁴ g mol^?1) from gel permeation chromatography (GPC) and molecular weight distribution (M_w/M_n = 1.5–7.6) of the resulting copolymer increased with copolymer yield. The cyanopropyl group, as a fragment of AIBN, was incorporated as a main constituent in the copolymer, the fraction of which increased from ca 10 to ca 20 % with copolymer yield, hence indicating that the copolymerization is an initiator–fragment incorporation radical polymerization. The copolymers also contained IBVE units (10–30 %) and DVA units with intact double bond (8–36 %) and without double bond (45 %). The intrinsic viscosity of the copolymer was very low (0.1 dl g^?1) at 30 °C in tetrahydrofuran. The results from GPC–multi‐angle laser light scattering (MALLS), transmission electron microscopy (TEM) and MALLS revealed that individual copolymer molecules were formed as hyperbranched nanoparticles. Copyright © 2004 Society of Chemical Industry     

Electroreductive block copolymerization of dichlorosilanes in the presence of disilane additives

The electroreductive polymerization of dichloromethylphenylsilane in the presence of triphenylsilyl group‐containing disilanes such as hexaphenyldisilane followed by the electroreductive termination with chlorotriphenylsilane afforded triphenylsilyl group‐terminated polymethylphenylsilane in 15–32% yield. The isolated polymethylphenylsilane (M_n = 3350 g mol^?1, M_w/M_n = 1.4) was found to react as a macroinitiator to copolymerize with dibutyldichlorosilane under electroreductive conditions producing the corresponding block copolymer (M_n = 4730 g mol^?1, M_w/M_n = 1.2) in 38% yield. The ratio of monomer units (? MeSiPh? to? BuSiBu? ) of the copolymer was determined to be 75:25 using ¹H NMR analysis, which was in good agreement with the calculated ratio (74:26) on the assumption that molecular weight of the macroinitiator was not changed. The block structure of the resulting copolymer, poly(methylphenylsilane)‐block‐poly(dibutylsilane), was also confirmed by comparing its ¹H NMR and UV absorption spectra with those of polymethylphenylsilane, polydibutylsilane and a statistical copolymer prepared by electroreductive polymerization of dichloromethylphenylsilane with dibutyldichlorosilane. This method is applicable to the preparation of other types of macroinitiator such as triphenylsilyl group‐terminated polydibutylsilane, and polydibutylsilane‐block‐polymethylphenylsilane was also obtained using this macroinitiator. Copyright © 2011 Society of Chemical Industry     

Nitroxide‐mediated synthesis of styrenic‐based segmented and tapered block copolymers using poly(lactide)‐functionalized TEMPO macromediators

Poly(styrene)‐poly(lactide) (PS‐PLA), poly (tert‐butyl styrene)‐poly(lactide) (PtBuS‐PLA) diblocks, and poly(tert‐butyl styrene)‐poly(styrene)‐poly(lactide) (PtBuS‐PS‐PLA) segmented and tapered triblocks of controlled segment lengths were synthesized using nitroxide‐mediated controlled radical polymerization. Well‐defined PLA‐functionalized macromediators derived from hydroxyl terminated TEMPO (PLA_T) of various molecular weights mediated polymerizations of the styrenic monomers in bulk and in dimethylformamide (DMF) solution at 120–130°C. PS‐PLA and PtBuS‐PLA diblocks were characterized by narrow molecular weight distributions (polydispersity index (M_w/M_n) < 1.3) when using the PLA_T mediator with the lowest number average molecular weight M_n= 6.1 kg/mol while broader molecular weight distributions were exhibited (M_w/M_n = 1.47‐1.65) when using higher molecular weight mediators (M_n = 7.4 kg/mol and 11.3 kg/mol). Segmented PtBuS‐PS‐PLA triblocks were initiated cleanly from PtBuS‐PLA diblocks although polymerizations were very rapid with PS segments ～ 5–10 kg/mol added within 3–10 min of polymerization at 130°C in 50 wt % DMF solution. Tapering from the PtBuS to the PS segment in semibatch mode at a lower temperature of 120°C and in 50 wt % DMF solution was effective in incorporating a short random segment of PtBuS‐ran‐PS while maintaining a relatively narrow monomodal molecular weight distribution (M_w/M_n ≈ 1.5). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Melt viscosity of oligomeric triblock copolymers (type PEP) of ethylene and propylene oxides

Melt viscosity η at 25°C of four oligomeric triblock copolymers consisting of a central block of ethoxamer units and two end blocks of propoxamer units (PEP) (M_n × 10^?3 = 1 and 2; mole fraction of ethoxamer units x_E = 0.41, 0.57, and 0.74) was analyzed in terms of the theory advanced by Berry and Fox. The structure-dependent factor F(X) was deduced from the intrinsic viscosity data, and the mean friction factor per friction center ζ was computed from η and F(X). At a fixed molecular weight, it increases with increasing x_E. The dependence of ζ versus x_E was compared with curves computed from the data for homopolymers. The best agreement was obtained if the following values of the inherent friction factor (log ζ₀) were used: ?10.25 for poly(ethylene oxide) PEO and ?10.65 for PPO. © 1994 John Wiley & Sons, Inc.     

Controlled radical polymerization of styrene utilizing excellent radical capturing ability of diphenyl ditelluride

Summary The radical polymerization of styrene was investigated in the presence of diphenyl ditelluride (DPDTe) under varied conditions. In the polymerization without any radical initiator at higher temperature (125°C), the addition of DPDTe surely decreased the polymer molecular weight (M _n) while the polydispersity (M _w/M _n) was rather broad. The polymerization with benzoyl peroxide (BPO) as the initiator was also uncontrollable to afford polymers with broad M _w/M _n probably due to the redox side reaction of BPO with DPDTe. On the contrary, the precision control of M _n and the initiating end structure could be achieved by the polymerization with 2,2'-azobisisobutyronitrile (AIBN), that is, M _n increased in proportion to the molar ratio of monomer to initiator suggesting the suppression of bimolecular chain termination reactions by the excellent radical capturing ability of DPDTe. Received: 23 June 1999/Revised version: 11 August 1999/Accepted: 16 August 1999     

The synthesis of high molecular weight polybutene‐1 catalyzed by Cp★ Ti(OBz)3/MAO

A new stereoregular polybutene‐1 was synthesized with a novel catalyst precursor η⁵‐pentamethyl cyclopentadienyl titanium tribenzyloxide (CpTi(OBz)₃) and methylaluminoxane (MAO). The effects of polymerization conditions on the catalytic activity, molecular weight and stereoregularity of the products were investigated in detail. It was found the catalyst exhibited highest activity of 91.2 kgPB mol Ti⁻¹ h⁻¹ at T = 30 °C, Al/Ti = 200. The catalytic activity and molecular weight were sensitive to the Al/Ti (mole/mole), polymerization temperature; they also depended on the Ti concentration. The molecular weight of the products increased with decreasing temperature. The structure and properties of the polybutene‐1 were characterized by ¹³C NMR, GPC, DSC and WAXD. The result showed the microstructure of polybutene‐1 extracted by boiling heptane was stereoregular, whereas the ether‐soluble fraction was atactic. The molecular weight of polybutene‐1 was over one million g mol⁻¹ and its molecular weight distribution ( M _w/ M _n) was from 1.1 to 1.2. © 2001 Society of Chemical Industry