选冶联合流程回收铜银金的工艺

采用ＤＸ 低碱度抑制剂， 用ＮａＯＨ 调节ｐＨ， 在ｐＨ＝ ９ ～１０ 的范围内浮铜抑硫， 使混合精矿中的有价金属与黄铁矿分离， 再选精矿产率２０ ％ ～３０ ％ ， 尾矿含金低于３ ．０ ｇ／ｔ。在较低的压力下（ 氧压０ ．４ ～０ ．６ ＭＰａ） 对所得精矿进行氧压氨浸， 使硫转化为硫酸铵， 铜进入溶液， 金银留在浸渣中。分选中金、银、铜回收率分别为９５ ％ ，９０ ％ 和８５ ％ ； 分选条件为ｐＨ＝ ９ ．５ ， 捕收剂用量２００ ｇ／ｔ， ＤＸ 抑制剂３ｋｇ／ｔ。低压氨浸铜浸出率为９５ ％ ， 浸出压力０ ．５ ＭＰａ， 温度１２０ ℃， 时间３ ｈ ， 氨浓度４５ ｇ／Ｌ。氰化浸出金、银浸出率为９７ ％ 和９５ ％ ， 置换率９９ ％ 和９８ ％ 。金、银、铜总回收率分别为９４ ％ ，８４ ％ 和８１ ％ 。     

从含锰氧化银矿中回收银

某含Ａｇ氧化矿石中，Ｍｎ６．１９％，Ａｇ１５３．３８ｇ／ｔ，进行了浮选，全泥氰化搅拌浸出试验。结果精矿Ａｇ回收率为１１．５５％，全泥氰化试验Ａｇ浸出率（按浸渣计）１０．７９％。用ＳＯ２在液体介质中浸出Ｍｎ，然后将浸渣氰化提Ａｇ，其浸出率９４．６５％。     

氮化物材料中氮的测定

建立了以双铂电极作指示电极，于ＫＢｒ─Ｎａ２Ｂ４Ｏ７介质中，用Ｃａ（ＣｌＯ）２滴定测定Ａ１Ｎ、ＴｉＮ、Ｓｉ３Ｎ４、Ｓｉ３Ｎ４／ＳｉＣ材料中氮的方法。本方法对于２０％－４０％的氮的测定，标准偏差小于０．２２％，可测定金属材料中０．０５％以上的氮。     

湿法炼锌银锌精矿综合回收新工艺研究

以西南某锌厂的锌浸出渣的浮选银锌精矿为原料提出了综合回收湿法炼锌的银锌精矿中银、硫、锌的新工艺,确定了工艺参数,通过小型实验验证了工艺的可行性.该工艺分为:混酸氧化浸出、渣水浸、银浸出三步.最佳条件下锌总浸出率按液计99.8％,银总浸出率按液计87.3％,硫富集于渣中,情况较好.     

银精矿碱法熔炼工艺的扩大试验

用正交试验法研究了熔炼温度、配煤量、配碱量及银精矿与铅精矿的质量比等因素对银精矿碱法熔炼中银、铅直收率的影响,建立了相应的回归模型;确定了苏打钾碱熔炼工艺的最佳工艺条件为：熔炼温度１０００～１０５０℃,停留时间１～２ｈ,配煤率４％～６％,钾碱率５％～７．５％及混矿比１∶１。此时,可获得含铅≥９８％,含银约１％的粗铅,铅、银的直收率分别大于９６％和９２％。     

溴化法浸出提取金和银

讨论了溴化法提取金银的热力学条件，用高银金精矿进行溴化法浸出实验，结果表明，一次浸出焙烧矿，金的浸出率９８％，银的浸出率９４％，效果明显。     

铂钯精矿中氯化银的浸出预处理研究

铜阳极泥分铜液所得铂钯精矿中的银主要以氯化银(AgCl)形态存在,可用氨水或亚硫酸钠作为浸出剂去除银。绘制了Ag⁺与NH3、SO2- 3配体组分图,结合电位-pH图分析表明,氨浸的pH值范围为7.7~13.5,亚硫酸钠浸出宜在中性或碱性条件下进行。优化条件实验结果表明,银的氨浸浸出率为95.3%,碲浸出率为14.9%,有微量铂、钯浸出;以亚硫酸钠为浸出剂,银的浸出率为97.3%,碲浸出率为11.5%,金、铂和钯均不被浸出。亚硫酸钠更适于作为铂钯精矿预处理除银的浸出剂。     

硫化锌银精矿富集银的工艺研究

基于国内外硫化锌矿处理的火、湿法研究进展,对含锌银精矿采用硫酸化焙烧、稀硫酸浸出工艺脱除锌、富集银,考察了焙烧和浸出过程中的主要影响因素。结果表明,硫酸配比为150%,在300℃焙烧90 min,以5%稀硫酸为浸出剂,液固比8:1,搅拌转速200~300 r/min,85℃浸出120 min,最终锌的浸出率可达到98%以上,浸出渣中银含量为7.24%,银被富集7倍。     

预浸-氰化浸出回收湿法炼锌渣中的银和金

某冶炼厂的锌浸出渣中银勘布粒度细,含银、金分别为381.3、1.02 g/t,可采用预浸-预浸渣氰化浸出工艺回收。重点研究了预浸条件对银、金浸出效率的影响。条件实验表明,药剂A比酸浸、氨浸具有更好的预浸效果;最佳预浸条件为药剂A浓度200 g/L、浸出液固比2:1、在50℃浸出3 h。综合条件实验得到的预浸渣渣率为66.2%,金、银的氰化浸出回收率分别为85.7%、92.9%。     

玻璃组分与Cu—Ni熔体过冷稳定性

在高真空下,研究了５０ ％ （７９ ％ Ｓｉ Ｏ２ ＋ １２ ．５ ％ Ｂ２ Ｏ３ ＋ ２ ．２ ％ Ａｌ２ Ｏ３ ＋ ０ ．６ ％ Ｃａ Ｏ ＋ ５ ．７ ％ Ｎａ２ Ｏ） （ 简写为 Ｎａ Ｃａ Ａｌ Ｂ Ｓｉ） ＋ ５０ ％ （ Ｎａ２ Ｂ７ Ｏ４） 对 Ｃｕ５０ Ｎｉ５０ 和 Ｃｕ７０ Ｎｉ３０ 合金熔体循环过热过程中过冷度稳定性的影响。结果表明,５０ ％（ Ｎａ Ｃａ Ａｌ Ｂ Ｓｉ） ＋ ５０ ％ （ Ｎａ２ Ｂ７ Ｏ４） 玻璃对合金熔体的净化过程为物理—化学复合净化, 且在（ Ｎａ Ｃａ Ａｌ Ｂ Ｓｉ） 净化剂中加入（ Ｎａ２ Ｂ７ Ｏ４） 玻璃形成的净化剂粘度适中,因此合金熔体在２ ～５ 次循环过热过程中可以获得稳定深过冷。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.