Effect of UV Radiation on the Removal of Carboxylic Acids from Water by H2O2 and O3 in the Presence of Metallic Ions

The effect of UV radiation on the removal of formic, oxalic and maleic acids from water by metallic ion (Fe²⁺ or Cu²⁺)/H₂O₂ and metallic ion/O₃ was studied and compared. The results showed that metallic ion/O₃/UV has higher efficiency than metallic ion/H₂O₂/UV for oxalic acid removal. UV radiation significantly increases the efficiency of metallic ion/H₂O₂ for formic and maleic acids removal while its effect on the efficiency of metallic ion/O₃ for formic acid removal is minor_. However, at pH 2, O₃ alone showed higher efficiency than metallic ion/H₂O₂/UV for formic acid removal. Contrary to the relative efficiency of metallic ions in the previous systems, Cu²⁺ exhibited higher rate than Fe²⁺ for the removal of the degradation products of maleic acid by O₃. UV radiation exhibited a minor effect on the efficiency of Cu²⁺/O₃, while it exhibited a large effect on the efficiency of Fe²⁺/O₃ for the removal of the degradation products of maleic acid.     

Oxidation of Propylene Glycol Methyl Ether Acetate Using Ozone-Based Advanced Oxidation Processes

The present study investigates the degradation of PGMEA and its TOC removal using O₃, UV/O₃, O₃/H₂O₂, and UV/H₂O₂ processes under various experimental conditions. Ozonation of PGMEA was substantially enhanced in the presence of UV light and H₂O₂. Approximately 33% of TOC enhancement was noted in UV/O₃ process over ozonation process. A linear relationship between PGMEA and H₂O₂ decomposition was observed in O₃/H₂O₂ and UV/H₂O₂ processes. The influence of solution pH on the decomposition of PGMEA was investigated and found that basic medium was the most efficient in all AOPs. After 60 minutes 62.4%, 100%, 90% and 54% of PGMEA decomposition at pH 10.0 was observed in O₃, UV/O₃, O₃/H₂O₂, and UV/H₂O₂ processes, respectively. It is concluded that UV/O₃ process is a promising approach for the oxidation and removal of PGMEA.     

Advanced Oxidation of Textile Wastewaters

Model dyeing and laundering wastewaters produced during two basic technological operations of the textile industry were subjected to treatment by advanced oxidation processes (AOPs). The following agents were used: ozone (O₃), hydrogen peroxide (H₂O₂) and UV radiation. They were applied separately and in all possible combinations: O₃ + UV, O₃ + H₂O₂, UV + H₂O₂, as well as all three at the same time: O₃ + UV + H₂O₂. Effluents before and after the treatment were analyzed according to requirements of the Polish Standards that included pH, color threshold, COD and concentration of anionic and non-ionic surfactants. Ozonation was carried out in a lab-scale bubble column reactor with a centrally located UV burner. The most effective version of AOPs proved to be the simultaneous use of all three agents. In the case of such treatment of dyeing wastewaters nearly complete discoloration and full decomposition of surface-active substances were obtained at 80% reduction of COD. A similar tendency was observed in the case of laundering wastewater, though in that case the results were slightly worse, which may be explained by much higher initial concentrations of the pollutants. Good treatment effects have also been obtained in combined treatment by simultaneous use of hydrogen peroxide and ozone.     

Comparison of Different Advanced Oxidation Processes Involving Ozone to Eliminate Atrazine

The oxidation of the herbicide atrazine by advanced oxidation processes (AOP) has been studied. The experiments were carried out in a tubular photoreactor, 2.5 L capacity, capable of providing good contact between the liquid and gas reactants. The decomposition rate of atrazine was determined at different pH using UV radiation, Hydrogen Peroxide, Ozone, Ozone/UV, Ozone/H₂O₂, H₂O₂/UV and Ozone/H₂O₂/UV processes. The effect of three different pH values was studied (4.7, 6.8, 11.7).     

Decomposition of Carboxylic Acids in Water by O3, O3/H2O2, and O3/Catalyst

This paper studies the decomposition of formic, oxalic and maleic acids by O₃, O₃/catalyst, and O₃/H₂O₂. The catalytic effect of Co²⁺, Ni²⁺, Cu²⁺, Mn²⁺, Zn²⁺, Cr³⁺, and Fe²⁺ ions is investigated. The results showed that—Co²⁺ and Mn²⁺ have the highest catalytic activity for the decomposition of oxalic acid while the catalytic effect of the studied ions is insignificant on the rate of decomposition of formic acid. Maleic acid decomposes by ozone into formic acid and glyoxylic acid, which subsequently oxidizes to oxalic acid. Though the studied ions have no effect on the decomposition of maleic acid, they have a significant effect on the produced oxalic and glyoxylic acids. In the presence of Cu²⁺ ions glyoxylic acid is mainly transformed into formic acid and traces of oxalic acid. In such case, a complete decomposition of maleic acid and its degradation products is achieved within 45 min. The results also show that combining H₂O₂ with O₃ results in an increase in the rate of decomposition of oxalic acid. However, O₃/H₂O₂ system is less active than O₃/Co²⁺ or O₃/Mn²⁺.     

Ozone-Based Advanced Oxidation Processes for the Decomposition of N-Methyl-2-Pyrolidone in Aqueous Medium

The present study investigates the decomposition of N-Methyl-2-Pyrolidone (NMP) using conventional ozonation (O₃), ozonation in the presence of UV light (UV/O₃), hydrogen peroxide (O₃/H₂O₂), and UV/H₂O₂ processes under various experimental conditions. The influence of solution pH, ozone gas flow dosage, and H₂O₂ dosage on the degradation of NMP was studied. All ozone-based advanced oxidation processes (AOPs) were efficient in alkaline medium, whereas the UV/H₂O₂ process was efficient in acidic medium. Increasing ozone gas flow dosage would accelerate the degradation of NMP up to certain level beyond which no positive effect was observed in ozonation as well as UV light enhanced ozonation processes. Hydrogen peroxide dosage strongly influenced the degradation of NMP and a hydrogen peroxide dosage of 0.75 g/L and 0.5 g/L was found to be the optimum dosage in UV/H₂O₂ and O₃/H₂O₂ processes, respectively. The UV/O₃ process was most efficient in TOC removal. Overall it can be concluded that ozonation and ozone-based AOPs are promising processes for an efficient removal of NMP in wastewater.     

Modeling dye degradation kinetic using dark- and photo-Fenton type processes

Dark- and photo-Fenton type processes, Fe²⁺/H₂O₂, Fe³⁺/H₂O₂, Fe⁰/H₂O₂, UV/Fe²⁺/H₂O₂, UV/Fe³⁺/H₂O₂ and UV/Fe⁰/H₂O₂, were applied for the treatment of model colored wastewater containing two reactive dyes, C.I. Reactive Blue 49 and C.I. Reactive Blue 137, and degradation kinetics were compared. Dye degradation was monitored by the means of UV/VIS, adsorbable organic halides (AOX) and total organic carbon (TOC) analysis, thus determining decolorization and dechlorination of triazine structure, as well as mineralization of model colored wastewater. Both dark- and photo-Fenton type processes were proven to be very efficient for color removal; ≥98% was achieved in all cases. Significant improvements in the mineralization of studied dyes were achieved by the assistance of UV light, as it was expected. It was demonstrated that the degradation kinetic of applied dyes depended on the presence of UV light, as well as type of iron catalyst and dye structure. On bases of the obtained experimental results, the mathematical models were developed describing dye degradation kinetics in all studied systems. Since UV light was used in order to enhance the efficiency of dark-Fenton type processes, mathematical model describing dye degradation by UV photolysis providing the values of quantum yields for each of the dye was developed and incorporated in model for photo-Fenton type processes. A sensitivity analysis for the evaluation of importance of each reaction used in mathematical models was also performed.     

Experimental Evidence of Gas-Liquid Boundary Controlled Reactions in UV-Ozone Systems

Oxalic acid is chosen as a model compound to study the UV + O₃ reactions in an heterogeneous continuous gas sparging reactor. Oxalic acid has the advantage of not reacting significantly with ozone alone, and when oxidized with O₃ + UV radiation, the reaction is of the single-step type : HOOC-COOH + O₃ (UV) = 2 CO₂ + H₂O + O₂. The reactions are of zero order as long as no additional alkalinity is introduced into the system. Evidence is that the photolysis of ozone is produced in the gas phase and that the reaction occurs in the gas-liquid boundary layer.     

Energy Trapping in Dications

The energy interaction curves of a number of diatomic and polyatomic dication systems were calculated in order to study their energy-trapping properties. Generally, the ab initio complete active space multiconfiguration self-consistent field method was used in an extended valence + polarization basis set, with compact effective potentials replacing the core electrons. The diatomic dications include all ten possible binary combinations of oxygen, sulphur, selenium, and tellurium. O₂²⁺ shows the largest exothermicity, measured from equilibrium to the monocation combination asymptote, and highest barrier to dissociation. The calculated equilibrium bond length and harmonic vibrational frequency agree very well with experiment. The O₂²⁺, SO²⁺, SeO²⁺, and TeO²⁺ series show progressively decreasing exothermicities but similar barrier heights. The non-oxides, in contrast, show similar exothermicities but decreasing barriers with increasing size of the atom constituents. These trends are interpreted in terms of both valence bond curve-crossing and molecular orbital bonding models. The ozone dication, O₃²⁺, is found to have a number of low-lying singlet and triplet stationary state structures spanning near-linear to D_3h2+ symmetries. Although the calculated exothermicity is even larger than for O₂²⁺, the barrier to O₂⁺ + O⁺ dissociation is predicted to be low in each case. O₂²⁺ surrounded by six argon atoms to model an isolating environment shows increased equilibrium O–O bond length, decreased exothermicity, and increased barrier to dissociation, relative to the bare dication. O₂²⁺ flanked at each end by a perpendicularly oriented H₂ molecule in a staggered conformation is obstructed from direct conversion to the water dimer dication by a high barrier. However, [(H₂O)₂]²⁺ dissociates smoothly from equilibrium to two water monocations with a large exothermicity but a small barrier.     

Advanced Oxidation of Tannic Acid in Aqueous Solution

Decomposition of tannic acid in aqueous solution in advanced oxidation processes has been studied. Different oxidizing agents: ozone, hydrogen peroxide and UV radiation have been used both as single and mutually combined components of the system. The course of reaction was examined by the changes of chemical oxygen demand (COD) and total organic carbon (TOC) in aqueous solutions. Particular attention has been paid to determine optimal concentration of hydrogen peroxide, when it is used alone, together with O₃ and in H₂O₂+O₃+UV combination. The most effective optimal concentration of H₂O₂ was found. The entire mineralization of tannic acid into final products CO₂ and H₂O can be accomplished in all combinations of advanced oxidation with ozone. Bacteriological test ToxAlert® with luminescence bacteria Vibro fisheri proved that toxicity of solutions decreased considerably during advanced oxidation of tannic acid solution.     

Chemical treatment of cork‐processing wastewaters for potential reuse

The chemical treatment of cork‐processing wastewater by ozonation, alone and in combination with hydrogen peroxide and UV radiation was investigated. A reduction of the chemical oxygen demand (COD) ranging from 42% to 76% was obtained during ozonation after 3 h of reaction, depending on the experimental conditions. The additional presence of hydrogen peroxide and UV radiation enhanced the efficiency of the ozonation treatment due to the contribution of the OH radicals formed in the decomposition of ozone. Thus, final reductions of the COD higher than 90% and a complete elimination of phenolic compounds and absorbance at 254 nm were achieved in both Advanced Oxidation Processes (AOPs), O₃/H₂O₂ and O₃/UV. Therefore the effluent resulting from the ozonation treatments can be reused in the cork‐processing industry. In a second step, the chemical treatment was conducted by means of UV radiation alone and by the action of hydroxyl radicals, which were generated by the following AOPs: UV/H₂O₂, Fenton's reagent, and photo‐Fenton system. The single photochemical process resulted in 9% of the organic matter present being removed, while the AOPs significantly enhanced this reduction with values in the range 20–75%. Kinetic studies for both groups of treatments were performed, and apparent kinetic rate constants were evaluated. In the ozone‐based experiments, the rate constants ranged from 1846 to 10922 dm³ mol^?1 O₃ h^?1, depending on the operating conditions. In the oxidation experiments using oxidants other than ozone, the rate constants varied between 0.06 and 1.19 h^?1. Copyright © 2004 Society of Chemical Industry     

The Chemistry of Water Treatment Processes Involving Ozone,Hydrogen Peroxide and Ultraviolet Radiation

Advanced oxidation processes are defined as those which involve the generation of hydroxyl radicals in sufficient quantity to affect water purification. The theoretical and (practical yield of OH from O₃ at high pH, 0₃/H₂0₂, O₃/UV and H₂O₂/UV systems is reviewed. New data is presented which illustrates the importance of direct photolysis in the O₃/UV process, the effect of the H₂0₂:0₃ ratio in the O₃/H₂O₂ process, and the impact of the low extinction coefficient of H₂O₂ in the H₂0₂/UV process.     

3D rectangular WO3 hybridized by PrFeO3 nanoparticles with efficient dual charge transfer for enhanced photo-Fenton-like activity

In this work, zero-dimensional (0D) high crystalline PrFeO₃ worm nanocrystals were loaded over a three-dimensional (3D) rectangular WO₃ to construct a 0D/3D PFO/W Z-scheme heterojunction by an in situ ultrasonic synthetic process. This heterojunction exhibited excellent photocatalytic activities towards the degradation of organic pollutants such as rhodamine B (RhB), Methylene blue (MB), and tetracycline hydrochloride (TC) in the presence of small amounts of H₂O₂ under visible-light irradiation. For example, the k value of PFO/W + H₂O₂ was about 67, 107, 45, 27, 11 and 14 times higher than pure H₂O₂, PrFeO₃, WO₃, PFO/W nanocomposite, PrFeO₃+ H₂O₂ and WO₃+H₂O₂ respectively during the degradation of MB. The trapping experiments and ESR measurements identified that the generated ·OH, ·O₂⁻, and h⁺ were the active species involved in the catalysis. Further, the ·OH radical could be continuously generated by Fe³⁺/Fe²⁺ and W⁶⁺/W⁵⁺ conversion and played the dominant role in the degradation of organic pollutants. The superior photocatalytic performance of the PFO/W + H₂O₂ system was derived from the synergistic effect of the Z-scheme heterostructure and dual photo-Fenton-like oxidation (Fe³⁺/Fe²⁺ and W⁶⁺/W⁵⁺). A possible mechanism was postulated based on the results obtained. In summary, this study provided new insights into synthesizing an effectively heterogeneous 0D/3D Z-scheme dual photo-Fenton-like catalyst for water clarification.     

Performance of yttria-stabilized zirconia fuel cell using H2–CO2 gas system and CO–O2 gas system

This paper reports the performance of an yttria-stabilized zirconia fuel cell (YSZ) using five kinds of gas systems. The final target of this research is to establish the combined fuel cell systems which can produce a H₂ fuel and circulate CO₂ gas in the production process of electric power. A large electric power was measured in the H₂–O₂ gas system and the CO–O₂ gas system at 1073 K. The formation process of O²⁻ ions in the endothermic cathodic reaction (1/2O₂+2e⁻→O²⁻) controlled the cell performance in both the gas systems. The electric power of the H₂–CO₂ gas system, which allowed to change CO₂ gas into a CO fuel (H₂+CO₂→H₂O+CO) in the cathode, was 1/31–1/11 of the maximum electric power for the H₂–O₂ gas system. This result is related to the larger endothermic energy for the formation of O²⁻ ions from CO₂ molecules at the cathode (CO₂+2e⁻→CO+O²⁻) than from O₂ molecules. The CO–H₂O gas system and the H₂–H₂O gas system was expected to produce a H₂ fuel in the cathode (CO+H₂O→H₂+CO₂, H₂+H₂O→H₂+H₂O). Although relatively high OCV values (open circuit voltage) were measured in these gas systems, no electric power was measured. At this moment, it was difficult to apply H₂O vapor as an oxidant to the cathodic reaction in a YSZ fuel cell.     

UV/H2O2氧化联合Ca(OH)2吸收同时脱硫脱硝

在小型紫外光-鼓泡床反应器中,对UV/H₂O₂氧化联合Ca(OH)₂吸收同时脱除燃煤烟气中NO与SO₂的主要影响因素[H₂O₂浓度、紫外光辐射强度、Ca(OH)₂浓度、NO浓度、溶液温度、烟气流量以及SO₂浓度]进行了考察。采用烟气分析仪和离子色谱仪分别对尾气中的NO₂和液相阴离子作了检测分析。结果显示:在本文所有实验条件下,SO₂均能实现完全脱除。随着H₂O₂浓度、紫外光辐射强度和Ca(OH)₂浓度的增加,NO的脱除效率均呈现先大幅度增加后轻微变化的趋势。NO脱除效率随烟气流量和NO浓度的增加均有大幅度下降。随着溶液温度和SO₂浓度的增加,NO脱除效率仅有微小的下降。离子色谱分析表明,反应产物主要是SO₄^2-和NO₃^-,同时有少量的NO₂^-产生。尾气中未能检测到有害气体NO₂。     

Thermal decomposition of ammonium sulphate

The thermal decomposition and vaporisation of ammonium sulphate, (NH₄)₂SO₄, is shown to take place via two distinct sets of reactions. In the first, ammonium pyrosulphate, (NH₄)₂S₂O₇, is the primary condensed phase product: 2(NH₄)₂SO₄ ← (NH₄)₂S₂O₇+2NH₃+H₂O The second stage concerns the decomposition of the pyrosulphate. Ammonia, sulphur dioxide, nitrogen and water are the major products, the dominant reaction being 3(NH₄)₂S₂O₇ ← 2NH₃+6SO₂+2N₂+9H₂O     

A comparative study on the performance of different advanced oxidation processes (UV/O3/H2O2) treating linear alkyl benzene (LAB) production plant's wastewater

A detailed investigation on photooxidation of linear alkyl benzene (LAB) industrial wastewater is presented in this study. The process analysis was performed by varying four significant independent variables including two numerical factors (initial pH (3–11) and initial H₂O₂ concentration (0–20 mM)) and two categorical factors (UV irradiation and ozonation). The experiments were conducted based on a central composite design (CCD) and analyzed using response surface methodology (RSM). To assess the process performance, two parameters viz. TCOD removal efficiency and BOD₅/COD were measured throughout the experiments. A maximum reduction in TCOD was 58, 53, 51, and 49%, respectively for UV/H₂O₂/O₃, H₂O₂/O₃, UV/O₃ and UV/H₂O₂ processes at the optimum conditions (initial pH of 7, initial H₂O₂ concentration of 100 mM, and reaction time of 180 min). A considerable increase in BOD₅/COD ratio was obtained in the combined processes (0.46, 0.51, 0.53, and 0.55 for UV/H₂O₂, UV/O₃, H₂O₂/O₃ and UV/H₂O₂/O₃, respectively) compared to the single oxidant process (0.35). The results showed that mineralization of the LAB industrial wastewater in neutral pH is more favored than in acidic and basic pH. Gas chromatography–mass spectrometry (GC–MS) was applied to show the fate of organic compounds. In conclusion, the photooxidation process (UV/H₂O₂/O₃, H₂O₂/O₃, UV/O₃ and UV/H₂O₂) could be an appropriate pretreatment method prior to a biological treatment process.     

Decomposition of acetic acid by advanced oxidation processes

Decomposition of acetic acid, known as a non-degradable organic compound, was conducted for several advanced oxidation processes such as TiO₂-UV-H₂O₂, Fe²⁺-H₂O₂-UV, UV-H₂O₂ and TiO₂-UV system. Acetic acid was efficiency decomposed within 120 minutes of UV radiation under the initial concentration of 500 ppm. The initial chemical oxygen demands (COD _cr ) tended to increase as H₂O₂ was added in most reactions. However, the initial COD _cr was not increased as H₂O₂ was consumed for the oxidation of iron salt in the photo-Fenton oxidation process. COD _cr and concentration of acetic acid rapidly decreased as the mole ratio of hydrogen peroxide increased owing to rapid decomposition of the reactant at the beginning of reaction. All reactions show first order pseudo reaction rate. The COD _cr removal rate and the decomposition efficiency of acetic acid were fastest in the UV-H₂O₂ process.     

ELIMINATION OF BENZENE AND CHLOROBENZENES BY PHOTODEGRADATION AND OZONATION PROCESSES

Benzene (B) and two representative chlorobenzenes (1,4-dichlorobenzene (DCB) and 1,2,3-trichlorobenzene (TCB)) were oxidized by means of UV irradiation alone, ozone alone, and the combinations UV/H₂O₂ and O₃/H₂O₂. In the single photolytic process, the influence on the photodegradation of the pH, temperature, and type of radiation source used was established. A kinetic study was performed by evaluating the first-order rate constants and the quantum yields. The effect of the additional presence of hydrogen peroxide was pointed out in the combined process UV/H₂O₂,with the determination of the specific contribution of the radical pathway to the overall photodegradation system. In the oxidation by ozone based systems (ozone alone and the combination O₃/H₂O₂), the rate constants at 20°C for the reaction of each compound with ozone and hydroxyl radicals were determined.