Influence of geometry on gas holdups in a reversed flow jet loop reactor

The effects of ratio of draft tube to reactor diameter (D_d/D), liquid nozzle diameter (d_N), aeration tube diameter (d_G) and immersion height of the two-fluid nozzle into the draft tube (H_N) on overall and annulus gas holdups for the air-water system were evaluated experimentally in a reversed flow jet loop reactor over wide ranges of gas and liquid flow rates. Both the gas holdups increased with increasing gas and liquid flow rates and with decreasing d_N and H_N. The influence of d_G on gas holdups is found to vary with gas flow rates. Correlations are proposed to predict gas holdups.     

Hydrodynamics and mass transfer behavior in multiple draft tube airlift contactors

The draft tube configuration significantly affected the performance of an airlift contactor. The multiple draft tube configuration was demonstrated to give a better gas-liquid mass transfer when compared with a conventional one-draft-tube system. The airlift with a larger number of draft tubes allowed a higher level of bubble entrainment, which rendered a high downcomer gas holdup. This resulted in a higher overall gas holdup in the contactor. Liquid velocity was also enhanced by increasing the number of draft tubes. The ratio between downcomer and riser cross sectional areas, A _d /A _r , had a great effect on the system performance, where a larger A _d /A _r led to a lower downcomer liquid velocity and smaller quantity of gas bubbles being dragged into the downcomer. This resulted in low gas holdup, and consequently, low gas-liquid interfacial mass transfer area, which led to a reduction in the overall volumetric mass transfer coefficient. The presence of salinity in the system drastically reduced the bubble size and subsequently led to an enhancement of gas entrainment within the system. As a result, higher gas holdups and gas-liquid interfacial area were observed, and hence, a higher rate of gas-liquid mass transfer was obtained.     

Gas holdup in a two‐phase reversed flow jet loop reactor

Experimental investigations have been carried out in Reversed Flow Jet Loop Reactor (RFJLR) to study the influence of liquid flow rate, gas flow rate, immersion height of two‐fluid nozzle in reactor and nozzle diameter on gas holdup without circulation, that is, gas–liquid mixture in draft tube only (E_gd) and gas holdup with circulation loop (E_g). Also critical liquid flow rate required for transition from draft tube to circulation loop has been determined. Gas holdup was measured by isolation valve technique. Gas holdup in draft tube and circulation loop increased with increase in liquid flow rate and gas flow rate. It is observed that the increased flow rate is required for achieving a particular value of gas holdup with larger nozzle diameter. Nozzle at the top edge of draft tube have higher gas holdup as compared to other positions. It has been noted that, no significant recirculation of gas bubbles into the top of draft tube from annulus section has been observed till a particular liquid flow rate is reached. A plot of gas holdup with no circulation and with circulation mode determines minimum liquid flow rate required to achieve complete circulation loop. Critical liquid flow rate required to achieve complete circulation loop increases with increase in gas flow rate and is minimum at lowest immersion height of two‐fluid nozzle.     

HYDRODYNAMIC CHARACTERISTICS AND GAS-LIQUID MASS TRANSFER IN A DRAFT TUBE SLURRY REACTOR

Fundamental characteristics of hydrodynamics and mass transfer have been measured in an air lift slurry reactor with a draft tube. The solid suspension capacity, i.e., the critical solid holdup, the gas holdup and the volumetric gas-liquid mass transfer coefficient were measured in the two draft tube columns of 0.1485 and 0.10?m in diameter. Four activated carbon beads ranging in size from 0.25 to 2.19?mm in average diameter were utilized as suspended solids in the experiments.

The critical solid holdup in the draft tube slurry column is found to be much greater than that in the conventional bubble column. An empirical correlation is developed to account for the critical solid holdup behavior in the draft tube column. The gas holdup in the draft tube column agrees well with that in the bubble column. The overall gas-liquid mass transfer coefficient, k₁awas measured by the oxygen probe method. The effect of solid holdup on k₁a is found to be negligible in the present system. The empirical equation is developed to correlate k₁a in the draft tube slurry reactor.     

气-液-固三相循环流化床局部相含率分布

应用自行开发的微电导探针测试技术,以玻璃珠(d_p=0.48 mm, ρ_s=2460 kg•m^-3)和苯乙烯颗粒(d_p=1.45mm,ρ_s=1264 kg•m^-3)为固相,空气为气相,水及0.05%、0.20% (质量)SCMC(羧甲基纤维素钠)水溶液为液相,对三相循环流化床(TCFB)的各相局部含率进行了同时测定.考察了不同表观液体速度、辅助液体速度、液体黏度及颗粒密度对局部相含率轴径向分布的影响. 在不同操作条件下,获得了1286套局部相含率实验数据. 给出了局部固含率和局部气含率与操作条件、流体物性及床层轴径向位置的关联式,关联式的计算值与实验值吻合较好.     

γ射线透射技术测量气液鼓泡塔内气含率的轴向分布

引　言鼓泡床反应器以其具有良好的传热、传质、相间充分接触和高效的可连续操作等特点在许多领域得到了广泛的应用 ,如氧化、加氢、烷基化、污水处理等工业过程 .在鼓泡反应器中气体以分散相的形式存在 ,轴向气含率分布是反映气泡在鼓泡塔反应器内运动行为的重要参数之一 .虽然采用了各种测量方法对流体力学行为进行了大量研究[1～ 3] ,取得了一定的研究成果 ,但工业过程往往是在高温高压的条件下操作 ,大部分的测量方法难以适应这种条件 ,所以探求新的测试技术尤为重要 .　　γ射线透射技术不仅用于塔设备的故障检测 ,而且用于其他的石油…     

Characteristics of solid suspensions in a bubble column without and with draft tube

In order to investigate the suspension behaviour of solid particles in bubble columns without and with draft tube, minimum gas velocities for generating and maintaining complete solid suspension were determined. Experiments were carried out in a bubble column with a diameter of 200 mm and a height of 2 500 mm. The bubble column could be equipped with a draft tube with a diameter of 120 mm and a length of 1 500 mm. The state of suspension was determined by measuring the hydrostatic pressure as a result of suspended solid particles with an inductive pressure gauge. Solid content ε_s, solid density ?_s, particle size d_p, particle shape, particle size distribution, and solid wettability were varied. Furthermore measurements of integral gas holdup were carried out.     

固体装载率对局部相含率与液体速率的影响

在高径比(H/D=22.2)的气升式内环流反应器中,以空气-水-石英砂为物系,研究了固体装载率和表观气速对导流筒内局部固含率、下降区固含率、下降区液体速率的影响,以及导流筒内局部气含率、固含率随轴向高度的分布规律。结果表明,固体体积分数小于或等于1.0%时,导流筒内局部固含率和下降区固含率与表观气速无关;下降区液体速率随表观气速和固体装载率的增加而下降;固定表观气速,在固体体积分数小于或等于2.0%时,导流筒内气含率在轴向是均匀分布的。     

Three‐phase airlift internal loop reactor: correlations for predicting the main fluid dynamic parameters

Three‐phase airlift loop reactors have many industrial applications. Examples include applications in the chemical, metallurgical, biochemical and minerals‐processing industries; fluid dynamics in such systems is a critical factor affecting efficiency. The experimental work was carried out at a pilot‐plant scale in a tank with a cylindrical shape and conical bottom (height 1.25 m; diameter 0.42 m), water and air were used as liquid and gas phases, and for different solid phases, different loads of glass spheres (diameters: 0.25 and 1 mm; density 2.6 g cm^?3), and polystyrene cylinders (diameter and length 3 mm; density 1.0 g cm^?3) were introduced. Air was injected through the bottom of the tank by means of 12 nozzles (diameter 1 mm each). An internal draft tube riser was tested on different configurations as its diameter was varied (44, 82, 125 and 240 mm) as was its height (1050 and 630 mm). Corresponding liquid velocities in the adjacent annular downcomer were determined by a thermal tracer technique, solid holdups were determined by conductivity methods, riser overall gas holdups were deduced from the liquid level, and riser gas holdup from manometer readings. Several adjusted correlations were considered in a method to predict the main fluid dynamic parameters (solids and gas holdups, and superficial liquid velocities). Copyright © 2005 Society of Chemical Industry     

HYDRODYNAMICS AND MASS TRANSFER IN BUBBLE COLUMNS: EFFECT OF SOLIDS

The hydrodynamics and mass transfer in a large diameter bubble column (D_c 0.305 m), specifically, the effects of gas velocity and the presence of solids on the gas holdup structure, gas-liquid interfacial area, and volumetric mass transfer coefficients in viscous as well as low viscosity solutions are studied. The sulfite oxidation technique was employed to measure the gas-liquid interfacial area. Volumetric mass transfer coefficients were measured using a chemical method (sulfite oxidation) as well as physical absorption of oxygen from air, and the overall gas holdups were measured using the hydrostatic head technique. The effect of solids on the gas holdup structure was examined using the dynamic gas disengagement method. With the addition of polystyrene particles, the gas-liquid interfacial area decreased for low viscosity systems, whereas it increased for viscous systems. This was shown to be due to the effect of solids on bubble coalescence. The wettability characteristics of solid surfaces in the presence of different liquids have been suggested as the reason for the effect of solids on coalescence. Oil shale slurries presented a special case because of the mineral dissolution effect.     

Hydrodynamics in down flow jet loop reactor

Gas holdup and liquid circulation time were measured in a down flow jet loop reactor for air–water system. It was observed that the circulation time decreases with an increase in nozzle diameter, draft tube to column diameter ratio and liquid velocity. Th gas holdup increases with an increase in gas and liquid velocities. The optimum draft tube to column diameter ratio was found to be 0.438. Correlations for gas holdup and circulation time involving operational and geometrical variables are presented.     

Gas holdup for high gas velocities in a gas–liquid cocurrent upward‐flow system

Gas holdup has been measured in an 83‐mm diameter, 2.2‐m high column at high gas superficial velocities — 0.22 to 2.7 m/s — and at liquid (water) superficial velocities of 0 to 0.47 m/s, by means of a differential pressure transducer. The equation of Hills (1976) based on the slip velocity gives good predictions of the gas holdup for 0.1 ≤ E_g ≤ 0.4. However, the holdups predicted by this approach are considerably higher than the experimental values at gas velocities high enough that E_g > 0.4. Other equations from the literature are also shown to be inadequate. The new data and earlier data at high gas velocities are therefore correlated with a new dimensional equation for U_l ≤ 0.23 m/s.     

Bubble Behavior of a Large‐Scale Bubble Column with Elevated Pressure

Gas holdups and the rising velocity of large and small bubbles are measured using the dynamic gas disengagement approach in a pressured bubble column of 0.3 m in diameter and 6.6 m in height. The effects of superficial gas velocity, liquid surface tension, liquid viscosity, and system pressure on the gas holdups and the rising velocity of small and large bubbles are investigated. The holdup of large bubbles and the rising velocity of small bubbles increase with increasing liquid viscosity and liquid surface tension. Meanwhile, the holdup of small bubbles and the rising velocity of a swarm of large bubbles decrease. Moreover, the holdup of large bubbles and the rising velocity of a swarm of small bubbles decrease with increasing system pressure. A correlation for the holdup of small bubbles is obtained from experimental data.     

液体黏度对气液固逆流三相湍动床动力学行为的影响

引　言逆流三相湍动床 (ITPTB) 仅由向上的气体来实现反应器的流化状态[1] 这类反应器因其独特的优点, 近几年受到人们极大关注并应用于催化过程、生物化工及环境工程领域[2]. 如在生物废水处Table 1　Physical properties of three phases and operation conditionsPhasesPhys     

Development of airlift bubble column dispersed with micro‐bubbles

Micro‐bubbles were dispersed in the bubble column with draft tube, and the length and diameter of draft tube were changed. The flow characteristics in air–water system were measured. Ozone gas and methylene‐blue aqueous solution were used, and the decomposition performance was examined. With increasing draft tube length, both the gas holdup and liquid velocity in the annular section increased. When the diameter ratio of draft tube to column was about 0.5, both the gas holdup and liquid circulation flow rate had maxima. For the decomposition by using ozone, the installation of draft tube enhanced the mass transfer and decomposition performance.     

Effect of geometrical parameters of draft tubes and clear liquid height on gas holdup in a bubble column for gas dispersion into tubes

The effects of the geometrical parameters of draft tubes and the clear liquid height on the average gas holdup E_G in a 0.16 m I.D. bubble column for gas dispersion into the tubes were experimentally studied in an airtap water system. The gas holdup depended on the superficial gas velocity U(ING), the kinds of gas spargers, the diameter and length of the draft tubes, clearance C_b between the lower end of the draft tube and the bottom of the bubble column, and the clear liquid height H_L. E_G increased with decreasing hole diameter of the gas sparger at a small gas velocity U_G, but did not depend on the kinds of gas spargers at a large U_G. E_G decreased with increasing clear liquid height H_L. The effect of H_L on E_G was well expressed by the modified three-region model. The experimental data of E_G were correlated.     

Studies on the hydrodynamic behavior and mass transfer in a down‐flow jet loop reactor with a coaxial draft tube

The effects of certain pertinent parameters such as gas and liquid flow rates and nozzle position on the behavior of a down‐flow jet loop reactor (DJR) have been studied. The mean residence times of gas and liquid phases and the gas holdup within the reactor have been measured. In addition, the overall volumetric mass transfer coefficient, and the influence of the gas flow rate and the position of the nozzle inside the draft tube on the latter has been determined. Correlations have been presented for the gas holdup and k_La which take into account the length of the draft tube and the nozzle immersion height. The k_La values obtained at different power per unit volume (P/V) values in the DJR used in the present study compare favorably with data presented for stirred tanks and bubble columns in the literature. The liquid residence time distribution (RTD) within the reactor has been studied by tracer analysis for various operating conditions and nozzle immersion height and the results are indicative of the high mixing intensities that can be obtained in such reactions. © 2001 Society of Chemical Industry     

Liquid phase residence time distribution for gas–liquid flow in Kenics static mixer

The residence time distribution (RTD) of the liquid phase for co-current gas–liquid upflow in a Kenics static mixer (KSM) with air/water and air/non-Newtonian fluid systems was investigated. The effect of liquid and gas superficial velocities on liquid holdup and Peclet number was studied. Experiments were conducted in three KSMs of diameter 2.54 cm with 16 elements and 5.08 cm diameter with 8 and 16 elements, respectively, of constant L_e/D_e = 1.5 for different liquid and gas velocities. A correlation was developed for Peclet number, in terms of generalized liquid Reynolds number, gas Froude number and liquid Galileo number, where as for liquid holdup, a correlation was developed as a function of gas Reynolds number. The axial dispersion model was found to be in good agreement with the experimental data.     

Residence time distribution and liquid holdup in Kenics KMX static mixer with hydrogenated nitrile butadiene rubber solution and hydrogen gas system

A Kenics^® KMX static mixer that has curved-open blade internal structure was investigated to study its hydrodynamic performance related to residence time distribution and liquid holdup in a gas/liquid system. The static mixer reactor had 24 mixing elements arranged in line along the length of the reactor such that the angle between two neighboring elements is 90°. The length of the reactor was 0.98 m with an internal diameter of 3.8 cm and was operated cocurrently with vertical upflow. The fluids used were hydrogen (gas phase), monochlorobenzene (liquid phase) and hydrogenated nitrile butadiene rubber solution (liquid phase). In all the experiments, the polymer solution was maintained as a continuous phase while hydrogen gas was in the dispersed phase. All experiments were conducted in the laminar flow regime with the liquid side hydraulic Reynolds number in the range of 0.04-0.36 and the gas side hydraulic Reynolds number in the range of 3-18. Different polymer concentrations and different operating conditions with respect to gas/liquid flow rates were used to study the corresponding effects on the hydrodynamic parameters such as Peclet number (Pe) and the liquid holdup (ε_L). Empirical correlations were obtained for the axial dispersion coefficient (D_a) and liquid holdup in liquid system alone and for the gas/liquid system separately. It was observed that the Peclet number decreased with the introduction of gas in to the reactor while in the liquid system alone, an increase in viscosity decreased the Peclet number. The liquid holdup was empirically correlated as a function of the physical properties of the fluids used in addition to the operating flow rates.     

The effect of liquid viscosity on gas holdup in a vertical pipe

The effect of liquid viscosity on gas holdup in a 15.1 mm diameter vertical pipe was assessed over the viscosity range 0.00092-1.670 N s m-². Gas holdup increased with increased liquid viscosity. The sensitivity of holdup to changes in viscosity was slight at low viscosity but was markedly increased at higher viscosities. Gas holdup was found to be well described, over the viscosity range studied, by the empirical equation: