Investigation of primers reducing the pink-ring formation in multilayer printed circuit boards

A rapid and easy screening test was applied to assess the capability of various formulated primers to reduce the defect of pink rings in multilayer printed circuit boards. The mixtures of silanes with multifunctional silanol groups (crosslinkers) and 3-glycidoxypropyl-trimethoxysilane

1 Systematic name: 3-(2,3-Epoxypropoxy)propyl-trimethoxysilane.

(referred to as silane C) or N-(2-aminoethyl)-3-aminopropyl-trimethoxysilane

2 Systematic name: 3-[N-2-aminoethyl]aminopropyl-trimethoxysilane.

(silane B) were proved to be effective in reducing the pink rings. The performance of the mixed silanes using silane A and crosslinkers with aromatic groups were better than other formulated primers which was partly attributed to less amounts of hydrophilic groups and better integrity in the primer films. A developed primer consisting of siloxane compounds had the best performance. The online test confirmed the results from the screening test and demonstrated the feasibility of the designed screening test in assessing the performance of primers. The results of FTIR spectroscopy and thermogravimetric analyses confirmed that the effective primers coated on the copper oxides could improve the curing reaction and the thermal oxidative stability of the epoxy/CuO system.     

Synthesis of phosphorus-containing polymers with potential bioactivity

Phosphorylation of poly(N-vinyl pyrrolidone-co-vinyl amine) and poly(N-vinyl pyrrolidone-co-glycidylcrotonate

1 Systematic name: (2,3-Epoxypropyl)crotonate.

) is realized by Atherton-Todd and Fields-Kabachnik reactions and by the means of direct interaction with phosphorus trichloride and phosphorus trichloride oxide. The composition and structure of the isolated final products was proved by NMR (¹H and ³¹P), IR spectroscopy and elemental analysis.     

Fracture behavior of coated/uncoated graphite-epoxy composites

The static delamination behavior of graphite/epoxy composite specimens subjected to mode I tensile opening (using UDCB

1 Uniform double cantilever beam.

specimens), and pure mode II shear loading (using ENF

2 End-notched flexural.

specimens) were studied. The graphite epoxy composites for the study were made from commercially treated fibers, with and without an electropolymerized interlayer. The mode I fracture energy (G_IC) was found to be significantly higher (more than 50 percent) for the coated fibers. However, this improvement was accompanied by a high reduction (more than 3 times) in the mode II fracture energy (G_IIC). This effect is apparently related to poor adhesion between the interlayer and the epoxy resin, which may be corrected by use of a “top layer” of appropriate composition to form chemical bonds between the phases. The fracture toughness (K_IC) of composites made with commercially treated fibers was also evaluated, using double side-notched specimens.     

Functional polyamides. 3. Synthesis and chelating properties of a new poly(amide thioether)

Polymerization of β,β′-(ethylenedithio)dipropionitrile

1 IUPAC name: 4,7-dithiadecane dinitrile.

with formaldehyde in the presence of sulfuric acid was carried out in order to permit the synthesis of polymides containing thioether groups. The obtained poly(amide thioether)s were characterized; they coordinate mercury (II) with a high degree of selectivity.     

Mass spectral studies of some epoxy resin precursors

The mass spectra were determined of three epoxy resin precursors: N,N-bis-(2,3-epoxypropyl)-N′,N′-dimethyl-4,4′-diaminodiphenylenemethane (G2A); N,N′-bis-(2,3-epoxypropyl)-N,N′-dimethyl-4,4′-diaminodiphenylene methane (G2S); and N′,N′,N′,N′-tetrakis-(2,3-epoxypropyl)-4,4′-diaminodiphenylene methane (TGDDM); and of three related model compounds: N,N-dimethylaniline (DMA); N-methyl-N-glycidylaniline (MGA) and N,N-digrycidylaniline (DGA). The results helped to confirm the structure of the resin precursors and are intended to pave the way for subsequent thermal degradation studies of cured resin samples. Despite the similarity in chemical structure of the compounds studied there are quite large differences in the mass spectral results obtained.     

Low dielectric,fluorinated polyimide copolymers

Copolymers of fluorinated polyimides and 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) have been prepared as films and composite laminates. The addition of BPDA was used as a means to achieve insolubility, making the polymers suitable as aircraft matrix resins. Glass transition temperatures, thermooxidative stabilities, and tensile strengths were increased with increasing BPDA content in the copolymers. Although the addition of BPDA did increase the UV cutoff and decrease the percent transmission slightly, the optical transparency of the polymers was still excellent. Dielectric constants of the copolyimide films ranged from 2.6 to 2.9. Astroquartz II laminates made with these resins had dielectric constant of 3.3–3.4. Flexural strength on unidirectional specimens were in the 1.24–1.41 GPa range and flexural moduli were 41 GPa. © 1994 John Wiley & Sons, Inc.

1 This article is a US Government work and, as such, is in the public domain in the United States of America.

     

The hierarchical structure and flexure behavior of woven carbon fiber epoxy composite

The hierarchical structure and flexure behavior of woven carbon fibers epoxy composite were investigated in this work. First, the hierarchical structure of the composite is characterized on three levels: composite, ply, and yarn. Structura imperfections,

1 In this paper, “structural imperfections” is used to describe the inherent structural characteristics of the actual composite, which deviate from the theoretically ideal and perfect composites, control, that are used in composite theories.

such as, ply‐ply misalignment, ply‐ply offset, and resin pockets, are identified and described. Second, a four‐point bending arrangement is used to study the flexure properties of the composite. Additionally, in‐situ traveling microscope and acoustic emission (AE) techniques are utilized to gain insight to the failure proceses during flexure test. AE showed early stages of matrix cracking before visual observation, which makes it a valuable tool for early failure detection.     

Properties of standard materials for reflection

This article gives a short survey of some literature on the calibration, suitability, properties, and use of various materials which are used as standards of reflectance. The classical ultimate reference standard, smoked magnesium oxide, is discussed briefly, and information is given on the properties of materials presently used: BaSO₄, Russian opal glasses, ceramic tiles, and Halon.

1 Halon is a registered trade name of the Allied Chemical Corporation.

The suitability of these materials for use as transfer standards or working standards is discussed.     

Porous bead aliphatic-aromatic methacrylate copolymers,I. Effect of polymerization conditions on porous structure formation of methyl methacrylate — di(methacryloyloxymethyl)naphthalene copolymers

The influence of inert porogenic mixture and monomer mixture composition and concentration on specific surface areas, pore size distribution, volumes of pores capable of capillary condensation of nitrogen and true density of copolymers were investigated for a new type of methacrylate monomer system: methyl methacrylate and di(methacryloyloxymethyl)naphthalene. The obtained copolymers exhibit similar character as it is typical for PPS

1 PPS = Porous by Precipitant and Solvent.

styrene-divinylbenzene resins.     

Photochemical and thermal stability of amaranth (FD&C red no. 2) in aqueous media

The decomposition of the formerly

1 This dye was delisted by the U. S. Food and Drug Administration in 1976, and has not been legally used in the U. S. in foods, drugs, or cosmetics since that date.

used food and pharmaceutical dye amaranth (FD&C Red No. 2) in water was studied under a variety of conditions. A matter of some concern is that one of the decomposition products is α-naphthylamine, a known carcinogen.     

Physical aging in thermosets of differing degrees of cure—master curve generation and the relation to mechanical properties

Physical aging of a thermoset system based on bisphenol-A epoxy (DER

1 Trademark of The Dow Chemical Company.

383) and tetrabromobisphenol-A cured with sulfanilamide and diaminodiphenylsulfone was studied as a function of cure history. Changes in the dynamic mechanical spectra for the thermoset system were correlated to changes in relative toughness associated with physical aging as determined by plane-strain biaxial tension-compression yield measurements. It was found that master curves, generated by using tan δ data obtained in the β relaxation temperature regime, are well related to the corresponding changes in mechanical properties and, hence, have predictive value. Relative toughness decreases and compressive yield increases with decreasing tan 5 because of decreased molecular segmental mobility. The relative extent of physical aging for the as-cast thermosets was shown to be linearly related to the cure time.     

Simultaneous fluorine elimination and alkylation of poly(tetrafluoroethylene)

PTFE (powder or foils) was defluorinated and derivatized in a one-step process by alkyl- and aryllithium in the presence of tetramethylethylenediamine

1 Systematic name: 1,2-Bis-[dimethylamino]ethane.

(TMEDA) as a catalyst. As evidenced by infrared (IR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and elemental analysis the C₄H₉-, C₈H₁₇-, C₁₂H₂₅- or phenyl groups were attached to a partly defluorinated macromolecular chain. Analogous reactions with dilithioaryl or dilithioalkyl agents presumably lead to crosslinking of the polymeric chains through alkyl or aryl groups. When the PTFE powder is treated with more concentrated RLi (>3 mol L^?1) at temperatures >150°C, the defluorination is almost quantitative even in the absence of the catalyst. The TMEDA-catalyzed reaction proceeds via elimination and nucleophilic addition. On the other hand, more concentrated RLi in the absence of the catalyst seems to react via a radical mechanism.     

Antioxidants and stabilizers, 107. Reaction of N-phenyl-1,4-benzoquinoneimine with the 1-cyano-1-methylethyl-radical

The reaction of N-phenyl-1,4-benzoquinoneimine (I)

1 Decoding of abbreviations see p. 103/104.

and 4-hydroxydiphenylamine (II) with the carbon centred 1-cyano-1-methylethyl radical (R^·) was studied in connection with an investigation of the action mechanism of industrial antidegradants, such as N-phenyl-N′-sec-alkyl-1,4-phenylenediamines. The mixture of I and II reacts very readily with R^·, giving rise to III , VI , and VIII . I alone reacts much slowlier, and the reaction mixture contains more products. IV and VII were identified along with III . Under the conditions used, II alone does not react at all. IV exists in two isomeric forms, syn and anti. VIII is very labile; XI was isolated from its transformation products. Reduction of IV gives V , which is labile, similarly to VIII .     

Epoxy systems with improved water resistance,and the non-fickian behaviour of epoxy systems during water ageing

N,N-Bis (2, 3-epoxypropyl) aniline and 4,4′-methylenebis-[N,N-bis (2,3-epoxypropyl) aniline] containing bromo, chloro, trifluoromethyl or polyfluoroalkoxy substituents were synthesised and cured with aromatic diamines in order to investigate the effect of substituted halogen on water absorption. Significant improvements were achieved: thus use of 4,4′-methylenebis-[N, N-bis (2, 3-epoxypropyl)-3, 5-dichloroaniline] and 4,4′-methylenebis-[N,N-bis (2,3-epoxypropyl)-3-(trifluoromethyl) aniline] instead of 4,4′-methylenebis-[N,N-bis (2,3-epoxypropyl) aniline] reduced the water absorption by about a half. Departures from Fickian behaviour were observed during water immersion ageing at room temperature and were a general feature of the epoxy systems examined. Plots of water absorption against the Fickian parameter (√t/d) usually showed at least mild sigmoid character and were not independent of specimen thickness. Further, slow continued uptake of water occurred during long-term ageing, and evidence is provided that the associated network distortions are reversible.     

Styrene emulsion polymerization in the presence of a maleate-functional surfactant

Dodecylhemiester of maleic anhydride is a very good anionic stabilizer for the emulsion polymerization of styrene. Rather high solid contents may be produced. Up to about 70% of the surfactant can be grafted onto the surface of the particles. Upon floculation with calcium salt, only 3% of the surfactant is left in the washing water. © 1997 John Wiley & Sons, Inc.

1 This article is a US Government work and, as such, is in the public domain in the United States of America.

J Appl Polym Sci 65: 2289–2296, 1997     

Alumina trihydrate as a flame retardant filler for flexible vinyl compounds

In those flexible vinyl compounds which can accept fillers, alumina trihydrate can significantly improve flame resistance as measured by oxygen index

1 It should be appreciated that degrees of flammability as measured by small-scale tests such as oxygen index may in no way reflect the relative hazard of these same materials when involved in a fully developed fire.

. Over a range of plasticizer concentrations, the lower the concentration of burnable plasticizer, the greater the contribution of hydrate to flame retardancy. Combinations of alumina trihydrate with antimony oxide are especially effective for improving the flame resistance of flexible vinyl compounds.     

Ground State Complexes between 5-(4-Carboxyphenyl)-10,15,20-Tritolyl Porphyrin and Benzoquinones

The interactions of 5-(4-carboxyphenyl)-10,15,20-tritolyl porphyrin (TTPa)

1 Abbreviations: TTPa: 5-(4-carboxyphenyl)-10,15,20-tritolyl porphyrin; BQ: 1,4-benzoquinone; DQ: 2,3,5,6-tetramethyl 1,4-benzoquinone; CHLQ: 2,3,5,6-tetrachloro 1,4-benzoquinone; DMSO: dimethyl sulfoxide

with benzoquinones have been studied by spectrophotometry and steady state and transient fluorescent methods. TTPa forms a 1:1 molecular complex with 1,4-benzoquinone, 2,3,5,6-tetramethyl 1,4-benzoquinone and 2,3,5,6-tetrachloro 1,4-benzoquinone in dimethyl sulfoxide at room temperature. The equilibrium constants for the interaction of TTPa with the different quinones were evaluated.     

Oxidative aging of thermoplastic polyimide films

Two linear polyimides were subjected to accelerated isothermal aging at temperatures between 300 and 400°C. Losses in toughness correlated well with changes in glass transition temperature (T_g) of the films, but not with weight loss. Both materials have extrapolated lifetimes of 100,000 h near their T_g's. © 1995 John Wiley & Sons, Inc.

1 This article is a US Government work and, as such, is in the public domain in the United States of America.

     

Gel permeation chromatography: Physical characterization and chromatographic properties of porasil

Porasil

1 Porasil is the Water Associates registered trademark for a powdered porous silica chromatographic substrate.

porous silica has been characterized by the methods of gas adsorption–desorption isotherms, mercury porosimetry, and electron microscopy. The pore structure has been shown to be quite heterogeneous, particularly at the surface of the particles. From the same sample of Porasil, columns were packed and calibrated in a gel permeation chromatograph. The availability of high molecular weight fractions of polystyrene allowed the exclusion limit of these materials to be determined for the first time. The heterogeneous pore structure did not seem to affect the effectiveness of these materials for macromolecular separation.     

Grafting of methyl methacrylate on isoprene rubber

Methyl methacrylate has been grafted on artificial isoprene rubber (IR) latex, with use of redox initiation. The properties of latices containing up to 40 phr

1 Parts per hundred parts of rubber.

methyl methacrylate (MMA) as well as solid products containing up to 80 phr of this compound were studied. Compared with ungrafted IR latex with the same solids content, the grafted IR latices had a lower viscosity, owing to their particle size being larger. Vulcanised films obtained from the grafted latices showed a considerably higher modulus, particularly at large deformations, than those based on IR or blends of IR with polymethyl methacrylate. by incorporation of certain reinforcing white fillers in the MMA-grafted IR latices, a further increase in the modulus of the latex films was effected.