分散方法对低含量碳纳米管玻纤/环氧层板性能的影响

采用超声波振荡与超声波破碎两种分散方法制备了低含量碳纳米管(CNTs)增强的环氧树脂, 研究了CNTs对树脂流变特性、 固化特性和力学性能的影响。进一步采用该树脂体系通过真空灌注工艺(VARIM)制备了CNTs含量为0.01%的CNTs-玻璃纤维/环氧树脂复合材料层板, 研究了两种分散方式下CNTs对复合材料层板力学性能的影响和CNTs的增强机制。结果表明: 超声波破碎分散使CNTs长度变短, 分散性更好, 与超声波振荡分散方式相比, CNTs对树脂增黏效果和树脂固化反应的影响更明显。采用双真空灌注工艺, 两种超声波分散方式下CNTs均提高了复合材料的弯曲性能、 层间剪切性能和树脂与纤维的粘结强度, 而单真空灌注工艺下CNTs的增强效果不明显, 说明受纤维过滤作用的影响, 选择合适的灌注工艺和CNTs分散方式, 低含量CNTs可实现对灌注工艺复合材料层板的增强。     

基于流变学的CNTs/SBS复合改性沥青性能及储存稳定性研究

为了探究碳纳米管(CNTs)对苯乙烯-丁二烯-苯乙烯嵌段共聚物(SBS)改性沥青的高低温性能及储存稳定性的改善效果,采用动态剪切流变试验(DSR)与弯曲梁蠕变试验(BBR)对CNTs/SBS复合改性沥青的流变特性进行评价,并基于软化点差值、流变学指数和荧光显微镜图像分析胶结料中聚合物分散状态。结果表明：CNTs加入后进一步增强了SBS改性沥青的高温抗车辙性能,且随CNTs掺量增加,高温性能逐步提升。CNTs的加入对改性沥青低温蠕变性能有不利影响,1.0%CNTs掺量下复合改性沥青更具性能效益。CNTs可以显著地提升SBS在沥青中的分布状态,CNTs与SBS形成均匀网状结构,在提升储存稳定性的同时具备增强沥青抗变形的能力,且CNTs的最佳掺量为1.0%。     

表面修饰碳纳米管对玻璃纤维及复合材料的性能影响

玻璃纤维因良好的力学性能被广泛应用于增强复合材料,而玻璃纤维与树脂基体的界面是影响复合材料性能的关键因素之一。实验中将碳纳米管(CNTs)改性后均匀地分散到浸润剂中,利用玻璃纤维在线成型工艺直接涂覆到玻璃纤维表面并制备复合材料。通过力学性能测试和显微形貌分析,结果表明CNTs能较好地分散于浸润剂和玻璃纤维表面,发现0.5%(质量分数)CNTs可以显著提高玻璃纤维的拉伸强度,并能显著改善纤维和基体的结合强度,从而提高复合材料的强度。     

碳纳米管在水泥基复合材料中的分散方法研究进展

碳纳米管(CNTs)作为性能优越的新型纳米材料被广泛用于增强基体材料,但是其易团聚且难以分散,使得实现其在基体材料中的均匀分散成为研究的重点。详细介绍了CNTs在增强水泥基复合材料研究中的分散方法与分散机理,并比较了各种分散方法的优缺点。重点论述了超声时间、酸处理时间、表面活性剂种类与掺量等因素对CNTs分散效果的影响,并讨论了评价CNTs分散效果的表征方法。将CNTs均匀分散到水泥基体中,可以显著提高复合材料的各项力学性能。     

玄武岩格栅增强水泥基复合材料单轴拉伸力学性能试验及本构关系模型

考虑玄武岩纤维增强树脂合物基复合材料(BFRP)格栅层数和水泥基复合材料(ECC)配比等因素,对BFRP增强大掺量粉煤灰/矿粉ECC棒骨试件进行了静力单轴拉伸试验,研究掺加增强粉煤灰/矿粉ECC的抗拉力学性能。结合试验数据,基于Richard和Abbot的弹塑性应力-应变公式提出掺加增强ECC的应力-应变本构关系模型。试验结果表明:随着掺加层数的增加,格栅增强ECC的极限抗拉强度显著增大。同配合比掺矿粉制成的ECC抗压强度、开裂应变及应力高于掺粉煤灰制成的ECC。掺加增强掺矿粉ECC试件相对掺粉煤灰ECC试件具有较好的抗拉力学性能。计算结果表明,建立的单轴受拉本构关系模型可以有效地预测掺加增强ECC的应力-应变关系和极限抗拉强度。     

磁场诱导定向碳纤维增强水泥砂浆的力学性能

首次利用磁场诱导定向技术,制备了具有明显择优取向的碳纤维增强水泥砂浆,表征与测试了不同水灰比、龄期和纤维掺量的水泥砂浆的碳纤维取向、抗压和劈裂抗拉强度,研究了碳纤维的取向性对力学性能提升效果的影响。结果表明:水灰比、纤维掺量对碳纤维的取向性有显著影响;相较于无择优取向的普通碳纤维增强水泥砂浆,经磁场诱导定向的碳纤维增强水泥砂浆的劈裂抗拉强度有显著增加,而抗压强度无明显变化;相同水灰比下,纤维取向和纤维掺量是影响定向碳纤维增强水泥砂浆劈裂抗拉强度的主要因素。其中,定向碳纤维增强水泥砂浆劈裂抗拉强度增强效率的最佳碳纤维掺量为水泥的0.50%。      

氧化石墨烯复掺石墨烯对水泥砂浆力学性能的提升及机理研究

采用高温还原氧化石墨烯(GO)方法制备石墨烯(G),利用GO对G的助分散效果将G与GO同时掺入砂浆中(即复掺)以改善水泥砂浆力学性能。通过不同含量G与GO混合溶液的吸光度测试,研究了GO对G的分散作用,结果表明当G与GO浓度比(C_G/C_(GO))为4/5时,GO对G的助分散效果最佳。然后保持吸光度测试中C_G/C_(GO),研究了不同G含量对复掺的水泥砂浆抗折抗压强度的影响。研究表明同等掺量下,复掺GO与G更能增强砂浆的力学性能,C_G/C_(GO)在3/5,4/5时提升效果较优,且复掺GO与G对砂浆早期力学性能提升效果更明显;TG测试表明复掺水泥的水化速度快于单掺G水泥。微观测试研究表明GO与G同时掺入水泥,既可以发挥GO对G的助分散效果,又能对水泥起到协同增强作用,促进了水泥的水化,水化产物晶型更加规整。研究采用GO助分散G的方法,既可以发挥GO对G的助分散效果,又能对水泥起到协同增强功效。     

碳纳米管加入方式对碳纤维/环氧树脂复合材料层间性能的影响

针对碳纤维/环氧树脂预浸料,对比了直接在树脂中加入碳纳米管(CNTs)后制备预浸料以及将CNTs喷涂在预浸料表面2种CNTs加入方式对CNTs-碳纤维/环氧树脂复合材料层合板I型与II型层间断裂韧性及层间剪切强度的影响。通过对树脂黏度、固化反应以及玻璃化转变温度的考察,分析了CNTs含量对树脂性能的影响,考察了添加方法对CNTs长度与形态的影响。分析了2种CNTs加入方式对CNTs-碳纤维/环氧树脂层合板断裂韧性及层间剪切强度的改善效果与作用规律。结果表明:CNTs的加入使树脂的黏度提高,固化反应程度下降;2种分散方法对CNTs的长度与形态无明显影响;直接在树脂中加入CNTs对CNTs-碳纤维/环氧树脂复合材料I型与II型层间断裂韧性的提高效果低于在碳纤维/环氧树脂预浸料表面喷涂CNTs的方式,后者的CNTs利用率较高;由于CNTs团聚及对树脂固化反应的影响,CNTs含量过高会使得其对CNTs-碳纤维/环氧树脂层合板的增韧效果下降。     

碳纳米管改性泡沫镍/环氧树脂复合材料阻尼性能

采用一种新型简易的化学气相沉积法(CVD)直接在泡沫镍表面均匀地沉积生长碳纳米管(CNTs),然后通过真空导入模塑成型工艺(VIMP)将选定的环氧树脂体系填入表面负载CNTs的泡沫镍孔洞,制备CNTs-泡沫镍/环氧树脂复合材料。利用FE-SEM、TEM和Raman对在不同反应温度条件下泡沫镍表面形貌和所生成CNTs的形貌、结构及石墨化程度进行了表征,并采用动态机械分析仪(DMA)研究了CNTs对泡沫镍/环氧树脂复合材料阻尼性能的影响。结果表明:当反应温度为680℃时,在泡沫镍表面可获得较好的CNTs沉积效果,且所生成的CNTs石墨化程度和纯度较高且直径尺寸较为均匀。同时所制备的CNTs-泡沫镍/环氧树脂复合材料比泡沫镍/环氧树脂复合材料,最大损耗因子tanδ_(max)从0.69提高到0.78,玻璃化转变温度Tg从60℃偏移到68℃,有效阻尼温域ΔT从39℃扩宽到44℃,整体阻尼性能提高了18.9%。     

粉煤灰泡沫混凝土力学性能的研究

利用粉煤灰、石灰和水泥为原料,双氧水为发泡剂,制备粉煤灰泡沫混凝土,通过改变泡沫混凝土的水胶比、双氧水掺量和水泥掺量,测试其抗压强度,利用正交实验分析选出最优方案和最显著因素,并通过对泡沫混凝土断面照片进行黑白二值化处理,研究最显著因素与孔隙特征之间的关系。结果表明,双氧水发泡的粉煤灰泡沫混凝土抗压强度随着水泥掺量的增加而增大,随着双氧水掺量的增加而减小,随着水胶比的增大而出现减小的趋势,但是并不显著。随着泡沫混凝土水泥掺量的增加,泡沫混凝土的孔径逐渐减小。当水泥掺量为70%,双氧水掺量为3%,水胶比为0.55时泡沫混凝土力学性能最好。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...