两种不同水域的海水对水三相点温度的影响

本文介绍了为研究因不同区域海洋中海水的氧、氢同位素存在的差异对水三相点温度的影响而采用的方法。即选取两种不同水域的天然海水,按照相同的工艺制作水三相点容器,采用相同的方法复现水三相点,然后通过容器间的比对进而研究其对水三相点温度的影响。比对结果表明,利用此法制作的水三相点容器复现的水三相点温度在±0.04mK范围内一致,且水三相点的复现性均优于0.05mK。     

不同来源的水三相点容器的比对

本文介绍了水三相点在开尔文热力学温度和ITS-90国际温标中的重要地位.重点介绍了麦克劳式水三相点容器内冰套的冻制方法及水三相点的复现.同时,NIM与ISOTECH同种结构的水三相点容器进行比对.比对结果表明,不同来源的水三相点容器复现的水三相点值在±0.04mK范围内一致.     

冰点温度的确定

本文介绍了一种新的、类似水三相点容器结构的密封冰点容器.通过水三相点容器与冰点容器的比对,间接确定了一种高纯水制备的冰点的温度.实验结果表明：水三相点温度与冰点的平均温差为11.18mK.因此,冰点容器所复现的冰点温度为-1.18m℃.     

不同来源的水三相点容器的比对

本文介绍了水三相点在开尔文热力学温度和ITS-90国际温标中的重要地位。重点介绍了麦克劳式水三相点容器内冰套的冻制方法及水三相点的复现。同时,NIM与ISOTECH同种结构的水三相点容器进行比对。比对结果表明,不同来源的水三相点容器复现的水三相点值在±0.04mK范围内一致。     

冰点温度的确定

本文介绍了一种新的、类似水三相点容器结构的密封冰点容器。通过水三相点容器与冰点容器的比对,间接确定了一种高纯水制备的冰点的温度。实验结果表明:水三相点温度与冰点的平均温差为11.18mK。因此,冰点容器所复现的冰点温度为-1.18m℃。     

CCT-K7水三相点容器国际关键比对

在国际互认框架内,国家计量标准的国际等效性是通过国际计量委员会（CIPM）的咨询委员会组织的一系列国际关键比对来确定的。温度咨询委员会（CCT）委托国际计量局（BIPM）作为主导实验室组织了由20个国家实验室参加的CCT-K7水三相点容器国际关键比对。比对结果表明：这些国家基准水三相点值在0．171mK范围内一致。此外,为了减小国家实验室复现水三相点的系统差,需要进一步研究同位素组成对水三相点温度的影响以及同位素修正。     

两种不同的冰套冻制方法--固态干冰法、低温热管法

本文介绍了两种不同的冰套冻制方法--固态干冰法和低温热管法.采用这两种方法分别在两个水三相点容器内冻制冰套,通过实验研究冻制方法对水三相点温度的影响.实验结果表明这两种冻制方法对水三相点温度的影响非常小,即两个水三相点容器所复现的水三相点温度在±0.04mK范围内一致.     

两种不同的冰套冻制方法——固态干冰法、低温热管法

本文介绍了两种不同的冰套冻制方法———固态干冰法和低温热管法。采用这两种方法分别在两个水三相点容器内冻制冰套 ,通过实验研究冻制方法对水三相点温度的影响。实验结果表明 :这两种冻制方法对水三相点温度的影响非常小 ,即两个水三相点容器所复现的水三相点温度在± 0 .0 4mK范围内一致     

高准确度水三相点容器

水三相点的高精度复现及准确测量是保证国际温标ITS-90实施的关键。水三相点容器内高纯水的同位素组成会影响复现的水三相点温度值。为了提高水三相点复现水平,减小氢氧同位素的影响,研制了带有氢氧同位素分析的石英及硼硅玻璃高准确度水三相点容器。为了评价容器的性能,开展了硼硅玻璃和石英水三相点容器的比对。实验结果表明:同位素修正前,石英玻璃和硼硅玻璃水三相点容器复现的水三相点在0.058mK范围内一致;同位素修正之后,容器之间的差异在0.017mK范围内一致。采用高准确度水三相点容器复现水三相点的扩展不确定度为0.066mK(k=2)。     

液氮冻制冰套法对水三相点温度的影响

介绍了液氮作为冷却剂在水三相点容器内冻制冰套的方法。利用该方法同时在两个不同真空度的水三相点容器内分别冻制冰套。通过实验，研究了此方法对所复现的水三相点温度的影响。实验结果表明：冻制过程中产生的应力以及开始生成的小冰晶引起水三相点温度偏低；并且，其对水三相点温度的影响随着水三相点容器内真空度的降低而增大。随着应力慢慢消除，小冰晶逐渐长大为大冰晶，所复现的水三相点值逐渐回升并趋于稳定。因此，为了高精度复现和准确测量水三相点，采用该冻制方法时，必须将冰套老化至少5天以后，才可以消除其对水三相点温度的影响。     

Analysis of the Comparison of TPW Realizations in Europe in Light of CCT Recommendation 2 (CI-2005)

Three comparisons of different triple-point-of-water (TPW) realizations in Europe have been organized under the auspices of EUROMET (EUROMET Projects 278, 549, and 714). Thirty European national metrology institutes were involved in these three comparisons that took place from 1994 to 2005. The aim of these successive projects was to assess the uncertainties associated with the practical realization of the triple point of water in Europe. Fifty-four TPW local cells were compared to a traveling standard cell (ref 679) circulated with an isothermal enclosure. The same equipment was used for the three projects, and LNE-INM regularly checked the stability of the TPW standard cell. Recently, LNE-INM has devoted efforts to bring the French standard at the triple point of water into close agreement with CIPM Recommendation 2 (CI-2005). The isotopic fractionation between water and ice when the cell is in use was experimentally studied. Several new TPW cells delivered by the manufacturer with water samples were added to our batch of reference cells. A French laboratory analyzed the isotopic compositions of these samples. These actions allow the French national definition of temperature at the triple point of water to be changed. A new temperature was associated with TPW cell 679 in agreement with the CIPM recommendation. In this presentation, the latest TPW cell measurements carried out by LNE-INM are presented. The results from EUROMET Projects 278, 549, and 714 are investigated in light of these changes.     

Isotopic Composition of Water Used in Triple-Point Cells

Isotopic analysis of the water used in KRISS triple point of water (TPW) cells was performed by three separate laboratories. The δD and δ ¹⁸O isotopic composition of six ampoules, made from two TPW cells, were analyzed by isotope ratio mass spectrometers. The analysis data showed that δD and δ ¹⁸O were − 62.17‰ and − 9.41‰ for the KRISS-2002-Jan cell, and − 36.42‰ and − 4.08‰ for the KRISS-2005-Jun cell. The temperature deviation of the triple point of water for these cells calculated from Kiyosawa’s data and the definition of the TPW were + 45.07μK for the KRISS-2002-Jan cell, and + 25.49μK for the KRISS-2005-Jun cell. The KRISS TPW temperature was + 92μK higher than the CCT-K7 KCRV after correcting for the deviation of the isotopic composition from Vienna Standard Mean Ocean Water.     

The Impact of Isotopic Concentration,Impurities, and Cell Aging on the Water Triple-Point Temperature

In 2005, the National Institutes of Standards and Technology (NIST) and Fluke’s Hart Scientific Division initiated a study to validate the isotopic correction algorithm applied to the realization temperature of triple point of water (TPW) cells. Additionally, the study quantified the impact of water sample impurities on the TPW cell realization temperature. For this study, eight TPW cells containing water of the same nominal isotopic concentration as Vienna Standard Mean Ocean Water (VSMOW) were used. Five of the cells were manufactured with fused-quartz envelopes and the remaining three with borosilicate envelopes. One TPW cell of each type was uniquely designed so that water samples could be periodically removed to analyze the isotopic composition and to monitor any changes in water purity with time and thereby correlate changes in composition with changes in realization temperature. The borosilicate TPW cells gave an average drift of −13 μK · yr⁻¹ and the more stable fused-quartz TPW cells gave an average drift of −2 μK · yr⁻¹.     

Behavior of Triple-Point-of-Water Cells for Different Sizes of the Ice Mantle

The effect of differences in the amount of ice mantle on the realization temperature of the triple point of water (TPW) was investigated. Three TPW cells were used in the experiment as the TPW cell under test. These TPW cells were manufactured at different times. An ice mantle was prepared for each cell, and the amount of these ice mantles was changed when the ice mantle was re-prepared. Comparison measurements were carried out between a standard TPW cell and the three cells under test, and the temperature difference was measured. As a result, although an identical TPW cell was used, a change in the temperature difference was observed when the amount of ice mantle was different. In the case of the TPW cell that was manufactured 30 years ago, the observed temperature change was larger than 0.1 mK. It is considered that the principal cause is the dissolution of glass elements from the TPW cell.     

金属外壳水三相点容器

水三相点是ITS-90国际温标中最重要的定义固定点,其复现不确定度是传递到整个温标的.目前,通常采用不同的冻制方法在硼硅玻璃或石英水三相点容器内冻制均匀的冰套来复现水三相点.冻制过程中,由于在水三相点容器内生成冰桥,会造成容器的破裂.为了解决此难题,研制了金属外壳水三相点容器,利用高纯水自发相变原理,在液体槽内自动冻制...     

VSMOW Triple Point of Water Cells: Borosilicate versus Fused-Quartz

To investigate an ideal container material for the triple point of water (TPW) cell and to reduce the influence to the triple-point temperature, due to the deviation of the isotopic composition of the water, both borosilicate and fused-quartz glass shelled TPW cells with isotopic composition substantially matching that of Vienna Standard Mean Ocean Water (VSMOW) were developed and tested. Through a specially designed manufacturing system, the isotopic composition, δD and δ¹⁸ O, of the water in the TPW cell could be controlled within ±10‰ (per mil) and ±1.5‰, respectively, resulting in control of the isotopic temperature correction to better than ± 8 μK. Through an ampoule attached to the cell, the isotopic composition of the water in the cell could be individually analyzed . After manufacture, the initial triple-point temperatures of the two types of cell were measured and compared to assess the quality of the cells and manufacturing process. Cells fabricated with the new system agree within 50 μK. Two innovatively designed borosilicate and fused-quartz TPW cells were made, each with six attached ampoules. One ampoule was removed every 6 months to track any changes in purity of the water over time.     

套管对水三相点的影响研究

为了研究套管对水三相点的影响,研制了计阱内径分别为16 mm和18 mm的水三相点容器以及直径为15.5 mm的套管。通过在计阱内加套管和不加套管,并利用准确度为0.02×10^-6的交流比较仪电桥测量标准铂电阻温度计在计阱内的电阻值,比较不同直径水三相点容器内套管对水三相点的影响。实验结果表明:实验中套管对水三相点值的影响小于30 μK,且在相同的测量条件下,套管的直径与水三相点容器温度计阱的内径越接近,套管对水三相点值的影响越小。