CaO-SiO2-Al2O3-Fe2O3渣系脱磷行为

利用Factsage软件计算了Al2O3含量对CaO-SiO2-Al2O3-Fe2O3四元渣系熔点和黏度的影响,并通过实验研究了在1 400℃时,CaO-SiO2-Al2O3-Fe2O3四元渣系对高磷铁水脱磷行为的影响.结果表明:渣中Al2O3的质量分数在3％～6％之间时,随着A12O3含量的增加,渣系的熔化温度迅速降低,进一步增加渣中的A12O3含量,渣系的熔化温度逐渐增加;Al2O3对CaO-SiO2-Al2O3-Fe2O3渣系的黏度影响不大;渣中Al2O3的质量分数在3％～6％之间变化时,渣系脱磷能力变化不是很大,脱磷率维持在91％左右,进一步增加渣系中A12O3的量,脱磷率逐渐下降;Al2O3对脱磷率产生影响可能是其改变了炉渣中液相所占比例,进而影响磷从铁水中向液相渣的传质过程.     

B2O3在CaO-BaO-SiO2-Al2O3-CaF2精炼渣中的作用

选择w（CaO）=46％,w（BaO）=10％,w（SiO2）=11．2％,w（Al2O3）=11．6％的渣作基础渣系,将B2q作助熔剂替代CaF2,发现B2q和CaF2的助熔效果相当,B2q可用作环保型助熔剂。将CaO-SiO2-BaO-Al2O3-CaF2作基础渣系,B2O3作酸性氧化物,在碱度（m（CaO＋BaO）／m（SiO2＋B2O3））为2．5和2．8时,研究B2O3替代SiO2后精炼渣的熔化性能。结果表明,B2O3替代25％的SiO2后就可大幅度降低粘度,并且发现富硼精炼渣的高温熔化性能稳定,粘度值稳定在0．3～0．5Pa·s。在碱度为2．8wt进行脱硫工艺实验,当w（SiO2）=20．6％时渣剂脱硫率为80％,当w（SiO2）=10．3％,w（B2O3）=10．3％时渣剂脱硫率为91．3％,主要原因是熔化性能良好的熔渣有助于提高传质速率。     

帘线钢中CaO-SiO2-Al2O3类夹杂物成分的控制

对帘线钢中CaO-SiO2-Al2O3类夹杂物CaO与SiO2的比值和Al2O3含量进行了研究,并且通过热力学计算对CaO-SiO2-Al2O3系塑性夹杂物的生成条件进行了讨论。结果表明：生产帘线钢时,为了得到塑性良好的夹杂物,钢液的氧活度应控制在0．0056～0．0113,而酸溶铝含量应控制在0．00010％～0．00025％范围内。     

CaO-SiO_2-FeO-P_2O_5-Al_2O_3脱磷渣系中组元活度的计算

2CaO·SiO_2-3CaO·P_2O_5含磷固溶体的生成可提高转炉液相渣的脱磷能力,减少渣量.但目前CaO-SiO_2-FeO-P_2O_5-Al_2O_3渣系中各组元活度的变化规律尚不明确,无法为分析含磷固溶体的形成机理提供理论依据.为此,本文依据分子离子共存理论建立了熔渣组元的活度模型,分析了不同条件下组元活度的变化规律.结果表明:随渣中Al_2O_3含量的增加,2CaO·SiO_2、3CaO·P_2O_5、3FeO·P_2O_5的活度逐渐降低;随着碱度的增大,3CaO·P_2O_5的活度升高,2CaO·SiO_2、3FeO·P_2O_5的活度则呈先升高后降低的趋势;随着渣中FeO含量的增加,2CaO·SiO_2、3FeO·P_2O_5及CaO·Al_2O_3的活度逐渐增大,并在w(FeO)为15%时达到最大值,之后逐渐降低;升高温度会导致CaO、3CaO·SiO_2的活度增大,2CaO·SiO_2的活度降低.     

Phosphorus Capacity of CaO-SiO2-Al2O3-MgO-FexO Slag

The CaO-SiO2-Al2O3-MgO-FexO slag occurs in the production process of Corex ironmaking technology.Most of its metallurgical properties,especially the phosphorus property,are different from the slag produced from blast furnace or converter.In order to explore the dephosphorization ability of CaO-SiO2-Al2O3-MgO-FexO slag,its phosphorus capacity was measured at 1 673 Kby gas-slag-metal equilibrium technique.An iron crucible was used as the reaction vessel,Ag alloy with 0.2% P was used as the metal phase which equilibrated with CaO-SiO2-Al2O3-MgO-FexO slag,and a constant flow of CO-CO2-N2 gas was used to provide oxygen partial pressure in the experiment.The effects of MgO,FexO and basicity on slag phosphorus capacity were investigated by single factor test.The results show that the phosphorus capacity rises firstly and then decreases with increasing MgO content under the condition of basicity 1.3,FexO content of 2% and Al2O3 content of 12%.The phosphorus value reaches maximum as the MgO content is 8%.When the basicity of slag is 1.1,MgO content is 10%,and Al2O3 is 12%,the phosphorus capacity increases with the increase of FexO content.The phosphorus capacity rises linearly when the basicity is increased from 1.1to 1.5.     

Mixed Alkali Effect in Viscosity of CaO-SiO2-Al2O3-R2O melts

Metallurgical and Materials Transactions B - The mixed alkali effects of Li2O, Na2O, and K2O on viscosity of CaO-SiO2-Al2O3 melts are investigated by rotating cylinder method. It is found that the...     

����������La2O3-Al2O3-CaF2����������Ũ��ģ��

In order to accurately control the rare earth content in liquid steel in electroslag remelting (ESR) process, according to the ion and molecule coexistence theory (IMCT) of slag structure and corresponding phase diagrams, a thermodynamic calculating model for the evaluation of mass action concentrations (designated by Ni for structure unit i) for La2O3-Al2O3-CaF2 slag system was formulated. The results show that the calculated values of NLa2O3 are in good agreement with the reported measured values, indicating that this calculating model can wholly embody the characteristics of the slag system. The activity of La2O3 decreases with the increasing of the Al2O3 and CaF2 content, and Al2O3 is stronger than CaF2 in decreasing the activity of La2O3. But the activity of La2O3 increase with the increasing in temperature at the composition range of 30% La2O3, 20% Al2O3, 50% CaF2. Above all, the activity of La2O3 in La2O3-Al2O3-CaF2 slag system can be quantitatively analyzed by this thermodynamic model, and this model can provide a theoretical basis for precisely controlling the lanthanum content in molten steel in ESR process.     

氮在Ca-SiO_2-Al_2O_3渣中的热力学研究

本文借助于光学碱度概念,对CaO-SiO_2-Al_2O_3熔渣中氮的稳定性进行了研究。结果表明,气相中氮不是与渣中自由氧离子作用,而是与网络结构作用而进入熔渣。根据氮与网络结构SiO_2或Al_2O_3之间的反应。提出了熔渣氮容量的新定义。根据渣中氮的行为,结合一系列的试验结果,得到了1823 K时CaO-SiO_2-Al_2O_3渣的氮容量计算公式IgC_N=-11.721gA-14.26和三元渣系的等氮容量曲线。     

Transition of Blast Furnace Slag from Silicates-Based to Aluminates-Based: Viscosity

Metallurgical and Materials Transactions B - The effect of Al2O3 and the Al2O3/SiO2(A/S) ratio on the viscosity of the CaO-SiO2-Al2O3-MgO-TiO2 slag system was studied in the present work. At a...     

CaO-SiO_2-Al_2O_3-V_2O_3四元系活度模型

根据熔渣结构的分子离子共存理论建立了CaO-SiO2-Al2O3-V2O3四元系活度模型。应用该模型计算出的活度数据,对用钒氧化物矿代替钒铁直接合金化冶炼高速钢的工艺过程进行了热力学计算和分析。用此活度数据计算了Al作还原剂时渣的平衡成分。计算结果表明,渣中V2O3的质量分数极低,直接合金化的热力学条件好,钒的理论最大还原率高。通过计算钢中或渣中的各种还原剂还原渣中V2O3的ΔG和LV,表明在炼钢工艺常用的所有还原剂中,Al的还原能力最强。     

低氧分压条件下CaO-SiO_2-P_2O_5(10%)-FeO体系热力学性质的研究

以促进2CaO·SiO_2-3CaO·P_2O_5固溶体生成的非均相脱磷工艺被视为未来实现转炉少渣冶炼的重要手段,但目前相关渣系热力学性质的研究较少,不能为合理解释非均相渣脱磷的机理提供理论依据.为此,本文利用FactSage热力学软件绘制了低氧分压(1mPa)条件下CaO-SiO_2-P_2O_5(10%)-FeO体系及其子体系的热力学相图,分析了不同温度下相平衡关系及液相线的变化规律.研究结果表明:升高温度可使体系中液相区及Ca_3(PO_4)_2初晶区的范围扩大,但会导致α'-Ca_2SiO_4的初晶区缩小以及Ca_2Fe_2O_5等物相的消失;降低氧分压可使体系的液相区缩小,并向高FeO的方向收缩;CaO-SiO_2-P_2O_5(10%)-FeO体系中存在较大的α'-Ca_2SiO_4与Ca_3(PO_4)_2共存区,尤其是α'-Ca_2SiO_4,Ca_3(PO_4)_2与Ca_2Fe_2O_5的三相共存区可极大地促进2CaO·SiO_2-3CaO·P_2O_5固溶体的生成.     

Recycling of High Ferrous Bauxite Reducing Slag for Synthesis of CaAl2 Si2 O8-Al2 O3-CaAl12 O19 Composite

CaAl_2 Si_2 O_8-Al_2O_3-CaAl_(12) O_(19)( CAS_2-Al_2O_3-CA_6) composite was synthesized through reaction sintering alumina and bauxite reducing slag.The CAS_2-Al_2O_3-CA_6 composite was mainly composed of α-Al_2O_3,CAS_2,and CA_6.Gehlenite( Ca_2Al_2 SiO_7,C_2AS) phase was effectively transformed to CAS_2 and CA_6through high-temperature reaction sintering under weak oxidizing atmosphere at 1400 ℃ for 4h.SEM( scanning electron microscopy) and EDS( energy dispersive spectroscopy) analysis indicated that black and needle-shaped Al_2O_3,rhombic or irregular polygonal-shaped Fe Al_2O_4,and glassy phase Ca_2Al_2 SiO_7disappeared after the reaction sintering.The light gray and flaky hexagon crystals of Ca Al_(12)O_(19)(10μm) and the grainy particles of Al_2O_3( 2-7μm) were observed in the CAS_2-Al_2O_3-CA_6 composite.The gray crystals of CAS_2 act as the binding phase and are distributed around CA_6 and Al_2O_3.CAS_2-Al_2O_3-CA_6 composite exhibits high refractoriness and service temperature,which are 1650 ℃ and 1450 ℃,respectively.Reaction sintering of alumina and bauxite reducing slag is a feasible method for the synthesis of CAS_2-Al_2O_3-CA_6 composite.     

不同碱度低氧化铝精炼渣对弹簧钢夹杂物成分的影响

为了优化55SiCrA弹簧钢中夹杂物的组成和形态,采用热力学软件Factsage分别研究了CaO、SiO_2含量对CaO-SiO_2-Al_2O_3-MgO与CaO-SiO_2-Al_2O_3-MnO系相图低熔点区域面积的影响,研究结果表明:随着CaO和SiO_2含量的增加,CaO-SiO_2-Al_2O_3-MnO系相图低熔点区域面积分数逐步增大;在CaO-SiO_2-Al_2O_3-MgO系中,当CaO的质量分数为40%,SiO_2的质量分数为50%时,对应相图的低熔点区域面积最大。同时,研究了不同碱度的精炼渣对钢样中夹杂物的影响,结果表明:当精炼渣的Al_2O_3含量相同时,随着精炼渣碱度的增大,夹杂物中Al_2O_3的含量不断增加,其成分逐渐偏离低熔点区域。当精炼渣中Al_2O_3的质量分数为8%,碱度为1.2时,可得到低熔点的塑性夹杂物,形貌多为球形,尺寸在5μm以下。     

CaO-SiO2-Al2O3-MgO-FeO渣系FeO活度的计算模型

利用熔渣结构共存理论建立了CaO-SiO2-Al2O3-MgO-FeO渣系FeO活度的计算模型,并分析了1400℃时炉渣碱度、MgO和FeO含量对该渣系FeO活度的影响规律。结果表明：当CaO-SiO2-Al2O3-MgO-FeO渣系三元碱度为1.3,Al2O3含量为12wt%,FeO含量为2wt%条件下,随MgO含量的增加,炉渣FeO活度增大;当二元碱度为1.1,Al2O3含量为12wt%,MgO含量为10wt%时,FeO活度随随渣中FeO含量的增加呈线性增加;当渣中Al2O3、MgO和FeO含量分别为12wt%、10wt%和2wt%固定不变时,随着二元碱度的提高,炉渣FeO活度迅速增加。计算得到的上述规律和实测规律一致,说明了本模型用于分析FeO活度的正确性。     

Viscosities Behavior of CaO-SiO2-MgO-Al2O3 Slag With Low Mass Ratio of CaO to SiO2 and Wide Range of Al2O3 Content

 The present paper is aimed at recycling of coal ash and blast furnace slag to produce mineral wool. Considering the mineralogical constitutions of coal ash and blast furnace slag, the primary quaternary slag compositions of CaO-SiO2-MgO-Al2O3 with basicity (mass ratio of CaO to SiO2) ranging from 05 to 09 and alumina ranging from 5% to 20% were investigated through a rotating cylinder method. The experimental results indicated that the viscosities decreased with increasing basicity above the liquidus temperature, and increased with increasing alumina content, and the maximum values were reached and as the alumina content was 20%, followed by the decrease with further increasing alumina content due to its amphoteric behavior. The amphoteric behavior of Al2O3 also performed in the relationship between viscosity and non-bridging oxygen per tetrahedrally-coordinated atom (NBO/T), and the viscosities decreased with increasing the NBO/T except the slag with a basicity 05 and Al2O3 20% which have a low NBO/T value and a low viscosity than others.-     

CaF2-SiO2-Al2O3-CaO-MgO五元渣系黏度的试验研究

为了研究含氟渣系成分变化对黏度的影响,根据五因素二次正交旋转回归法设计渣系配方,使用RTW-10熔渣物性测定仪,采用旋转柱体法,在1 600～1 300℃降温过程中对CaF2-SiO2-Al2O3-CaO-MgO渣系的黏度进行连续测定;建立了1 600℃下五元含氟渣系黏度的回归模型,研究了各组元对熔渣黏度的影响.结果表明:当CaF2的含量(质量分数,下同)在10％～70％时,随CaF2含量增加,黏度减小,随SiO2、Al2O3和MgO含量增加,黏度增大,CaO易受其他组元的作用而对黏度产生不同影响;在w(SiO2)=10％、w(MgO) =10％和w(CaF2)=50％时,随w(CaO)增加,黏度先增大后减小,w(CaO)=10％时黏度最大.在w(Al2 O3) =20％、w(MgO)=10％和w(CaF2)=50％时,随着w(CaO)增加,当w(SiO2)＜20％时,黏度先增大后减小;当w(SiO2)＞20％时,黏度持续减小.     

二元碱度和Al_2O_3对CaO-SiO_2-FeO-Fe_2O_3-P_2O_5-Al_2O_3-MgO-MnO钢渣中磷酸盐富集的影响

以八元CaO-SiO_2-FeO-Fe_2O_3-P_2O_5-Al_2O_3-MgO-MnO钢渣体系为研究对象,结合热力学计算和实验检测,分析了二元碱度B和Al_2O_3含量对八元钢渣系中磷酸盐富集行为的影响。结果表明:钢渣二元碱度和Al_2O_3含量直接影响钢渣中f-C2S的生成量,进而影响磷酸盐富集相nC_2S-C_3P内P_2O_5的含量。随着二元碱度从1.3提高至2.5,磷酸盐富集率增大,磷酸盐富集相nC2S-C3P中的P_2O_5含量呈现先迅速增大(B从1.3至1.7),然后逐渐减小(B从1.8至2.5)的趋势。当二元碱度和Al_2O_3质量分数分别控制在1.7和12%时,即当满足四元碱度R为1.23时,此八元钢渣体系有较好的磷酸盐富集效果,磷酸盐富集相nC_2S-C_3P内的P_2O_5的质量分数可以达到24.23%。     

Study on Transformation of CaO-Al₂O₃-SiO₂-MgO System Inclusions in ZG06Cr13Ni4Mo Stainless Steel

This paper aims at generally studying on the inclusions of ZGG06Cr13Ni4Mo ultra-low carbon stainless steel used for large scale hydraulic turbine sets. On the basis of analysis the industrial test samples, thermodynamic software FactSage is used to study inclusions transformation process in CaO-SiO2-Al2O3-MgO system while stainless steel is been smelting. The results illustrate the inclusions melting points and plasticity variation law. The reasonable inclusions plasticity controlling area is found out in low melting point. The melting point is up to 1280℃ While MgO weight concentration is 10% in CaO-SiO2-Al2O3-MgO system, SiO2, Al2O3 and CaO in inclusions are in weight concentration range of 50-70%, 10-20% and 10-40%, respectively. For purpose of gaining low melting point inclusions, silicon alumina radio in deoxidant should be controlled between 2-5 for ultra-low carbon stainless steel refining in industry.     

Desulfurization Characteristics of CaO-SiO2-BaO-CaF2-Al2O3-MgO Refining Slag

The desulfurizationcapability,as one of the mosti m-portant indexes of refining slag,has great influence onquality of steel.Desulfurization of molten steel with refi-ning slags has become a focal problemconcerned all overthe world[1-4].However,there weref…