Investigation of the relationships between the chain organization and rheological properties of atactic poly(vinyl alcohol) hydrogels

The structure and rheological behavior of atactic poly(vinyl alcohol) (a-PVA) hydrogels prepared by freeze/thaw cycles were investigated as a function of polymer concentration and number of freeze/thaw cycles. The presence of phases with different mobilities was observed using ¹³C CP/MAS and DP/MAS NMR experiments. The degree of crystallinity of the a-PVA-rich phase was determined by ¹H NMR free decay experiments. Measurements of the shear storage and loss modulus were performed at a fixed frequency of 1 Hz and a strain value of 0.1%, i.e. under conditions where the deformation imposed on the gel structure is entirely reversible. Results thus obtained showed that an increase in the number of freeze/thaw cycles induces an increase in the degree of crystallinity in the polymer-rich phase together with an increase in the storage modulus. The a-PVA hydrogels became more fragile as the number of freeze/thaw cycles was increased. Moreover, both the percentage of protons in a rigid environment measured by ¹H NMR and the storage modulus values tended to a limiting value after six freeze/thaw cycles. These results show that the first five or six freeze/thaw cycles play a very important role in determining the hydrogel structure and rheological properties. A more detailed comparison of NMR and rheological data led to the conclusion that the storage modulus is mainly controlled by the a-PVA crystallinity while the hydrogen bond interactions have a much smaller contribution.     

Effect of crosslinking on the mechanical and thermal properties of poly(vinyl alcohol)

Poly(vinyl alcohol) was crosslinked with hexamethylene diisocyanate in solution. A broad range of degrees of crosslinking, from 1.7 up to 74 mol% of reacted hydroxyl groups, was achieved. The variation of the thermal and mechanical properties of PVA with the crosslinking density show an initial decrease due to the diminution of the crystallinity of the system, caused by the crosslinking. After an abrupt rise at about 20%, the properties tend to level off independently on the increase of the crosslinking. This behaviour is explained as a result of the competitive action of at least three factors during the crosslinking: (i) weakening of the existing physical network due to hydrogen bonding; (ii) formation of a chemical network; and (iii) introduction of flexible moieties. The last factor is closely connected with the specific chemical structure of the crosslinker itself.     

Swelling and morphological properties of poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA) hydrogels in solution with high salt concentration

Understanding the swelling properties of hydrogels and how they affect the hydrogel's morphology is of fundamental importance in the development of hydrogel-based artificial muscles, bio-actuators, sensors and other devices. In this paper, the swelling behavior of PVA-PAA hydrogel films in saline water and in buffer solutions of different pH values was investigated. It was observed that the swelling factor of the hydrogel decreases when the ionic strength of the solvent solution increases. Scanning Electron Microscopy (SEM) revealed structures with different pore shapes and sizes depending on the type of solution used for hydration. In saline water, Energy Dispersive X-Ray (EDS) analysis indicated the formation of NaCl crystals within the polymeric network. Finally, the PVA-PAA hydrogel was used as an actuator to strain a fiber Bragg grating sensor, thus providing an indirect measurement of the pH value of the surrounding solution.     

Miscibility and interactions in poly(methylthiomethyl methacrylate)/poly(vinyl alcohol) blends

Poly(methylthiomethyl methacrylate) (PMTMA) is miscible with poly(vinyl alcohol) (PVA) over the whole composition range as shown by the existence of a single glass transition temperature in each blend. The interaction between PMTMA and PVA was examined by Fourier transform infrared spectroscopy, solid-state nuclear magnetic resonance spectroscopy and X-ray photoelectron spectroscopy. The interactions mainly involve the hydroxyl groups of PVA and the thioether sulfur atoms of PMTMA, and the involvement of the carbonyl groups of PMTMA in interactions is not significant. The measurements of proton spin-lattice relaxation time reveal that PMTMA and PVA do not mix intimately on a scale of 1-3 nm, but are miscible on a scale of 20-30 nm. In comparison, we have previously found that PMTMA is miscible with poly(p-vinylphenol) and the two polymers mix intimately on a scale of 1-3 nm.     

Water sorption in cross-linked poly(vinyl alcohol) networks

Poly(vinyl alcohol) (PVA) networks of different cross-linking densities were prepared by reaction with hexamethylene diisocyanate in solution and casting. The dynamic-mechanical properties of PVA films have been investigated in the temperature range of −150 to +150 °C. Two relaxations processes labeled α and β in order of decreasing temperature were observed. The α-relaxation shifts to lower temperature and the average molecular weight between cross-links decreases with increasing cross-linking density. Isothermal sorption from vapor and liquid water allowed determination of the Flory-Huggins interaction parameter between water and the polymer chain segments, which decreased with the water activity in the hydrogel and increased with the cross-linking density as a consequence of the hydrophobic character of the cross-linking agent. The water diffusion coefficients, D, in the networks obtained by means of dynamic sorption experiments increased with increasing water activity. This behavior is interpreted in terms of plasticization of the polymer by water molecules.     

Grafting and adsorption of poly(vinyl) alcohol in vinyl acetate emulsion polymerization

Poly(vinyl alcohol) is often used in vinyl acetate emulsion polymerization as a protective colloid, but its role is complex and controversial since it partakes in grafting reactions with the monomer, influencing process mechanisms, and affecting the colloidal properties of the latex. Furthermore, in industrial operations, the wide scatter of macromolecular properties of the commercial types of poly(vinyl alcohol) causes process irreproducibilities. In this work different types of polyvinyl alcohol were used to perform a series of polymerizations, and their kinetics were compared. A selective solubilization procedure was applied to separate the three fractions of poly(vinyl alcohol) in the final latex: free in the water phase, physically adsorbed onto the polymer particles and chemically grafted. These results were compared with those obtained from pure adsorption measurements of polyvinyl alcohol onto ‘emulsifier-free’ polyvinyl acetate dispersions. The rheological behavior of the different latexes was also compared, and the results were used to formulate an hypothesis on the interaction mechanisms acting in these systems.     

Fabrication of poly(vinyl alcohol)s (PVAs) nanotubes through the fusion of nanocapsules composed of PVAs multilayer films

Poly(vinyl alcohol) (PVA) nanocapsules were fabricated by the deposition of PVA multilayer films onto the surface of silica particles followed by the removal of the silica cores. When a water dispersion of PVA nanocapsules was dried on a substrate, PVA nanotubes were formed through the one-dimensional fusion of the nanocapsules. This fusion behavior of the PVA nanocapsules was strongly affected by the molecular weights and acetylation degrees of PVA, the capsule film thickness of the PVA nanocapsules and the temperature to dry a water dispersion of the nanocapsules. When nanocapsules composed of 20 layered films of acetylated PVA with a 14% acetylation degree were used, nanotube formation via the fusion of these nanocapsules occurred effectively upon drying the water dispersion at 20 °C.     

Gellan/poly(vinyl alcohol) hydrogels: characterization and evaluation as delivery systems

Bioartificial polymeric materials in the form of hydrogels were prepared starting from blends of poly(vinyl alcohol) (PVOH) with gellan, using a procedure based on freeze–thawing cycles. The effect exerted by gellan on the properties of these materials was investigated. The materials were loaded with human growth hormone (GH) and the release of the drug was evaluated. The results obtained indicated that gellan favours the crystallization process of PVOH allowing the formation of a material with a more homogeneous and stable structure than that of pure PVOH hydrogels. Both the PVOH melting enthalpy and the elastic modulus increased with increasing gellan content in the hydrogels; in addition, the higher the gellan content in the samples, the lower was the amount of PVOH released. Gellan/PVOH hydrogels were able to release GH and the release was affected by the content of the biological component. The amount of GH released was within a physiological range. © 2001 Society of Chemical Industry     

A comparison of two theoretical analyses of the elastodynamics of poly(vinyl alcohol) hydrogels

In two recent publications, Brillouin scattering measurements of the hypersonic velocity and attenuation in poly(vinyl alcohol) (PVA) hydrogels were analysed using two different theoretical models. These are the theories of Marqusee and Deutch for Brillouin scattering from gels and of Johnson for the elastodynamics of gels. In this work we take an overview of our previous results and also present new results particularly regarding a pair of important gel parameters. These new aspects enable us to compare critically the results obtained from the two theories and to comment on the suitability of the models to Brillouin scattering from PVA hydrogels.     

Compression of poly(vinyl alcohol) gels by ultracentrifugal forces

Compression due to ultracentrifugal forces was investigated for poly(vinyl alcohol) (PVA) gels. The concentration gradient profiles for the gels were obtained by experiment and were then compared with a theoretical prediction. By the application of the centrifugal forces, the concentration gradient near the bottom increases sharply whereas the gradient inside the gel remains almost constant in the region far from the bottom. Further application of the centrifugal forces enhances the peak near the bottom. These are well explained by the theory proposed in the previous paper [Urayama et al. J Chem Phys 2005;122:024906.]. The frictional coefficient f for the PVA gels, which originates from the friction between the polymer network and solvent molecules, is estimated to be 3.5×10¹⁴ N s m⁻⁴.     

Characterization of strong polyelectrolyte hydrogels based on poly(vinyl alcohol)

Maleic anhydride (MA) was grafted onto both partially and fully hydrolyzed poly(vinyl alcohol) (PVA) in the presence of an initiator. Strong polyelectrolyte polymers were prepared by sulfonation of PVA–MA grafts. The sulfonation was completed by reaction of hydroxyl groups of PVA–MA grafts with two different sulfonating reagents (chlorosulfonic acid and pyridine sulfonic acid). The sulfonation degree was evaluated by acid–base titration and ¹H NMR analysis. The solution behaviour of the prepared grafts was evaluated from viscosity measurements. Four kinds of water‐insoluble PVA–MA and PVA–MA‐SO₃H hydrogels were prepared by heat treatment, physical gelation and chemical crosslinking with different weight ratios of N,N‐methylene bisacrylamide (MBA) crosslinker. The swelling parameters were measured for all prepared gels in deionized water and aqueous solutions at different pH values from 2 to 12 having constant ionic strength (I = 0.1). All gels exhibit a different swelling behaviour upon environmental pH changes. Copyright © 2004 Society of Chemical Industry     

Synthesis of poly(vinyl alcohol) combs via MADIX/RAFT polymerization

Poly(vinyl acetate) combs have been prepared via macromolecular design via interchange of xanthate (MADIX)/reversible addition-fragmentation chain-transfer (RAFT) polymerization using xanthate functionalized polymer cores. The comb backbones were prepared using well-defined poly(vinyl alcohol) PVA polymers with a degree of polymerization of 20, 100 and 170, respectively. Functionalization with xanthates via R-group or a Z-group approach resulted in the formation of macromolecular MADIX agents. While Z group designed macromolecular xanthate agents appeared to inhibit the polymerization of vinyl acetate (VAc), R group designed macromolecular xanthate agents achieved to mediate efficiently the bulk polymerization of VAc affording PVAc combs. However, the growth of the combs was accompanied at low conversions by the formation of linear polymer chains as a result of the constant initiation (AIBN) and shoulders, which can be attributed to intermolecular coupling reactions. The proportions of single chains and termination products were observed to increase with the degree of polymerization of the macromolecular MADIX agents broadening the molecular weight distribution. As a result of a stable ester link between the branches and the PVA backbone, the branched PVAc architectures were finally hydrolyzed to afford poly(vinyl alcohol) combs.     

Characterization of degraded hydrogels based on poly(vinyl alcohol) grafted with poly(lactide‐co‐glycolide)

Poly(vinyl alcohol) (PVA) grafted with poly(lactide‐co‐glycolide) and cross‐linked as a material of increased hydrophobicity relative to PVA was produced. The properties were examined with respect to the mass loss, water uptake, hydrophilicity, and mechanical characteristics upon hydrolytical degradation. The hydrogels investigated display water uptake increasing with degradation time because of increasing hydrophilicity. The mass loss amounts up to 15% after eight weeks of degradation. The mechanical properties of the hydrogels are within the range of those of natural tissue, the E modulus is 18 MPa, or even 100–200 MPa, depending on the structure of material. The mechanical characteristic and their dependence degradation show the most recognizable correlation with the chemical structure. Studies of the topography of degraded samples (scanning electron microscopy) and IR measurements demonstrate the degradation to occur at slow rate due to the high degree of grafting. The mass loss is rather low and a bulk degradation mechanism takes place. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Microstructural studies on BaCl2 doped poly(vinyl alcohol)

We have studied the effect of BaCl₂ dopant on the optical and microstructural properties of a polymer poly(vinyl alcohol) (PVA). Pure and BaCl₂ doped PVA films were prepared using solvent casting method. These films were characterized using FTIR, UV-visible, XRD and DSC techniques. The observed peaks around 3425 cm⁻¹, at 1733 cm⁻¹ and 1640 cm⁻¹ in the FTIR spectra were assigned to O-H, CC stretching and acetyle CO group vibrations, respectively. In the doped PVA shift in these bands can be understood on the basis of intra/inter molecular hydrogen bonding with the adjacent OH group of PVA. The UV-visible spectra shows the absorption bands around 196 nm and shoulders around 208 nm with different absorption intensities for doped PVA, which are assigned to n→π* transition. This indicates the presence of unsaturated bonds mainly in the tail-head of the polymer. Optical band energy gap is estimated using UV-visible spectra and it decreases with increasing dopant concentration. The powder XRD shows an increase in crystallinity in the doped PVA, which arises due to the interaction of dopant with PVA causing a molecular rearrangement within the amorphous phase of polymer. These modifications also influence the optical property of the doped polymer. The DSC study also supports increasing crystalline thickness and degree of crystallinity due to doping.     

Facile fabrication of poly(vinyl alcohol) gels and derivative aerogels

A facile preparation of poly(vinyl alcohol) (PVOH) hydrogels and their derivative PVOH/montmorillonite clay aerogels is reported, using water as solvent and divinylsulfone as crosslinking agent, making use of an environmentally friendly freeze drying process. The materials exhibit significantly increased mechanical properties after crosslinking. The compressive modulus of an aerogel prepared from an aqueous suspension containing 2 wt% PVOH/8 wt% clay increased 29-fold upon crosslinking, for example. Crosslinking of the polymer/clay aerogels decreased the onset decomposition temperature as measured by thermogravimetric analysis, and generated a more continuous structure at higher clay contents. Such polymer/clay aerogels are promising materials for low flammability applications.     

Degree of crosslinking and mechanical properties of crosslinked poly(vinyl alcohol) beads for use in solid-phase organic synthesis

The limited swellability in polar media of the commonly used polystyrene/divinylbenzene (PS-DVB) support materials for solid-phase organic synthesis has led to the development of novel, highly swellable hydrophilic gels designed for use in aqueous or polar media. Poly(vinyl alcohol) beads crosslinked with epichlorohydrin (PVA-EP) were prepared by a two-step inverse-suspension polymerization method. While it is known that the morphology of the resulting beads can be controlled by the ratio of EP versus PVA as well as by the pre-crosslinking time, the actual degree of crosslinking of the beads and their mechanical properties remain unknown. It is therefore the purpose of this study to evaluate the actual degree of crosslinking of beads prepared with different quantities of crosslinker in the feed by spectroscopic (Raman, nuclear magnetic resonance) and chemical (functional group loading) methods. The mechanical properties of these swollen PVA-EP beads will be evaluated by single-bead unconfined compression in solvents such as water, N,N-dimethylformamide (DMF), and tetrahydrofuran (THF) and compared to model PS-DVB beads commonly used for solid phase synthesis.     

Thermal characteristics of poly(vinyl alcohol) and poly(vinylpyrrolidone) IPNs

Interpenetrating polymer network (IPN) hydrogels based on poly(vinyl alcohol) (PVA) and 1‐vinyl‐2‐pyrrolidone (VP) were prepared by radical polymerization using 2,2‐dimethyl‐2‐phenylacetophenone (DMPAP) and methylene bisacrylicamide (MBAAm) as initiator and crosslinker, respectively. The thermal characterization of the IPNs was investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dielectric analysis (DEA). Depressions of the melting temperatures of PVA segments in IPNs were observed with increasing VP content via the DSC. The DEA was employed to ascertain the glass transition temperature (T_g) of IPNs. From the result of DEA, IPNs exhibited two T_gs indicating the presence of phase separation in the IPN. The thermal decomposition of IPNs was investigated using TGA and appeared at near 270°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1844–1847, 2002     

Drying of semicrystalline polymers: mathematical modeling and experimental characterization of poly(vinyl alcohol) films

A mathematical model was developed to predict the drying mechanism of semicrystalline polymers involving multiple solvents. Since drying of semicrystalline polymers can be accompanied by changes in polymer degree of crystallinity, the model integrates crystallization kinetics and the Vrentas-Duda diffusion model to provide a better understanding of the mechanism. The model considers the effect of external conditions such as temperature, film shrinkage and diffusion and evaporation of multiple solvents during drying. Poly(vinyl alcohol) (PVA)/water/methanol was chosen as a test system. The drying kinetics of PVA films swollen in water and methanol were investigated using gravimetric techniques. The model predicts that higher temperatures, lower film thicknesses and lower methanol to water ratios increase the drying rate. The model predictions were compared with experimental data and showed good agreement.     

粉煤灰固定化细胞去除聚乙烯醇的研究

前期研究分离到一株能高效降解并矿化聚乙烯醇(PVA)的黄单胞菌(Xanthomonas sp.)。考察了利用改性处理或未处理粉煤灰吸附该菌株去除PVA的特性。结果表明,实验所采用的5种粉煤灰对该菌细胞等温吸附方程与Langmuir方程、Freundlich方程的拟合都达到很高的水平。改性粉煤灰对菌体细胞的吸附量由大到小的顺序为HC l处理粉煤灰>H2SO4处理粉煤灰>Ca(OH)2处理粉煤灰>NaOH处理粉煤灰>未处理粉煤灰。在培养初期,粉煤灰固定化细胞对PVA的去除量略低于等量游离细胞,但其去除速率的变化与游离细胞基本相同。