Spherulitic morphology and growth of poly(vinylidene fluoride)/poly(3-hydroxybutyrate-co-hydroxyvalerate) blends by optical microscopy

Poly(vinylidene fluoride) (PVDF) and poly(3-hydroxybutyrate-co-hydroxyvalerate) (PHBV), both semicrystalline polymers, are miscible as shown by the single glass transition temperature over the entire composition range. Morphology of PVDF/PHBV blends was investigated by optical microscopy under two different crystallization conditions. PVDF showed the spherulitic morphology at 150 °C in the PVDF/PHBV blends, where PHBV acted as the noncrystallizing component. PHBV also showed the spherulitic morphology within the matrix of the pre-existing PVDF crystals when PVDF/PHBV blends were quenched from the melt to the crystallization temperature below the melting point of PHBV. The spherulitic growth of PHBV was investigated as the function of both blend composition and crystallization temperature.     

Weak interaction,marginal miscibility,and ring‐band spherulites in blends of poly(vinylidene fluoride) with polyesters

Fourier transform infrared (FTIR) spectroscopy, optical microscopy (OM), and differential scanning calorimetry (DSC) techniques were used to probe phase behavior and interactions in blends of poly(vinylidene fluoride) (PVDF) and polyesters [poly(trimethylene adipate) (PTA) and poly(pentamethylene adipate) (PPA)] of relatively low crystallizability. DSC thermal analysis and OM characterization proved that PVDF was miscible with PTA and PPA with a low lower critical solution temperature. Small negative values of the interaction parameters (χ₁₂ = ?0.13 for a PVDF/PPA blend) were obtained with the melting‐point depression method. FTIR spectroscopy results revealed that interactions between ? CF₂ of PVDF and the ? C?O group of the polyester were weak, in agreement with the thermal analysis results. An increase in the coarseness and/or ring‐band spacing further provided supportive evidence that miscibility did exist between the polyester and PVDF constituents in the blends. Pattern changes in ring‐band spherulites of the miscible blends further substantiated the favorable, though weak, interactions between the PVDF and polyester constituents. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Viscoelastic and pressure–volume–temperature properties of poly(vinylidene fluoride) and poly(vinylidene fluoride)–hexafluoropropylene copolymers

The relationship between the pressure, volume, and temperature (PVT) of poly(vinylidene fluoride) homopolymers (PVDF) and poly(vinylidene fluoride)–hexafluoropropylene (PVDF–HFP) copolymers was determined in the pressure range of 200–1200 bar and in the temperature range of 40°C–230°C. The specific volume was measured for two homopolymers having a molecular weight (M_w) of 160,000–400,000 Da and three copolymers containing between 3 and 11 wt % HFP with a molecular weight range of 320,000–480,000 Da. Differential scanning calorimetry (DSC) was used to simulate the cooling process of the PVT experiments and to determine the crystallization temperature at atmospheric pressure. The obtained results were compared to the transitions observed during the PVT measurements, which were found to be pressure dependent. The results showed that the specific volume of PVDF varies between 0.57 and 0.69 cm³/g at atmospheric pressure, while at high pressure (1200 bar) it varies between 0.55 and 0.64 cm³/g. For the copolymers, the addition of HFP lowered its melting point, while the specific volume did not show a significant change. The TAIT state equation describing the dependence of specific volume on the zero‐pressure volume (V₀,T), pressure, and temperature has been used to predict the specific volume of PVDF and PVDF–HFP copolymers. The experimental data was fitted with the state equation by varying the parameters in the equation. The use of the universal constant, C (0.0894), and as a variable did not affect the predictions significantly. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 230–241, 2001     

Compatibilization of immiscible nylon 6/poly(vinylidene fluoride) blends using graphene oxides

A new strategy to compatibilize immiscible blends is proposed, using graphene oxide (GO) nanosheets taking advantage of their unique amphiphilic structures. When 0.5 or 1 wt% GOs were incorporated in immiscible nylon 6/poly(vinylidene fluoride) (PVDF) (90/10 wt%) blends, the dimension of PVDF dispersed particles was markedly reduced and became more uniform, revealing a well‐defined compatibilization effect of GOs on the immiscible blends. Correspondingly, the ductility of the compatibilized blends increased several times compared with uncompatibilized immiscible blends. In order to explore the underlying compatibilization mechanism, Fourier transform infrared and Raman spectra were applied to suggest that the edge polar groups of GOs can form hydrogen bonds with nylon 6 while the basal plane of GOs can interact with electron‐withdrawing fluorine on PVDF chains leading to the so‐called charge‐transfer C–F bonding. In this case, GOs exhibit favorable interactions with both nylon 6 and PVDF phase, therefore stabilizing the interface during GO migrations from PVDF/GO masterbatch to nylon 6 phase, which can minimize the interfacial tension and finally lead to compatibilization effects. Obviously, this work may open a broad prospect for GOs to be widely applied as a new compatibilizer in industrial fields. © 2012 Society of Chemical Industry     

Miscibility and morphology of poly(vinylidene fluoride)/poly[(vinylidene fluoride)‐ran‐trifluorethylene] blends

This study presents an investigation of the effect of the different crystalline phases of each blend component on miscibility when blending poly(vinylidene fluoride) (PVDF) and its copolymer poly[(vinylidene fluoride)‐ran‐trifluorethylene] [P(VDF–TrFE)] containing 72 mol % of VDF. It was found that, when both components crystallized in their ferroelectric phase, the PVDF showed a strong effect on the crystallinity and phase‐transition temperature of the copolymer, indicating partial miscibility in the crystalline state. On the other hand, immiscibility was observed when both components, after melting, were crystallized in their paraelectric phase. In this case, however, a decrease in crystallization temperatures suggested a strong interaction between monomers in the liquid state. Blend morphologies indicated that, in spite of the lack of miscibility in the crystalline state, there is at least miscibility between PVDF and P(VDF–TrFE) in the liquid state, and that a very intimate mixture of the two phases on the lamellar level can be maintained upon crystallization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1362–1369, 2002     

Tensile,stress-strain and creep rupture properties of poly (vinyl chloride)/poly(neopentyl glycol adipate)/poly(vinylidene fluoride) blends

Poly (vinyl chloride), PVC, and poly(vinylidene fluoride), PVDF, are incompatible polymers. Poly(neopentyl glycol adipate), PDPA, is miscible with both PVC and PVDF. With PDPA acting as a compatibilizer between PVC and PVDF. compatible PVC/PDPA/PVDF blends can be formed at PVDF content of about less than 50wt%. Above 50wt% PVDF the ternary blends exist in two phases exhibiting two glass transition temperatures, T_g, PVC is the main contributor to the mechanical strength while PDPA and PVDF contribute to the elastic properties of these blends. A compatible blend of 55/22.5/22.5 wt% PVC/PDPA/PVDF exhibiting one single T_g appears to show an interesting balance of the properties of the blend components.     

Electrospun fiber membranes from blends of poly(vinylidene fluoride) with fouling‐resistant zwitterionic copolymers

Nonwoven super‐hydrophobic fiber membranes have potential applications in oil–water separation and membrane distillation, but fouling negatively impacts both applications. Membranes were prepared from blends comprising poly(vinylidene fluoride) (PVDF) and random zwitterionic copolymers of poly(methyl methacrylate) (PMMA) with sulfobetaine methacrylate (SBMA) or with sulfobetaine‐2‐vinylpyridine (SB2VP). PVDF imparts mechanical strength to the membrane, while the copolymers enhance fouling resistance. Blend composition was varied by controlling the PVDF‐to‐copolymer ratio. Nonwoven fiber membranes were obtained by electrospinning solutions of PVDF and the copolymers in a mixed solvent of N,N‐dimethylacetamide and acetone. The PVDF crystal phases and crystallinities of the blends were studied using wide‐angle X‐ray diffraction and differential scanning calorimetry (DSC). PVDF crystallized preferentially into its polar β‐phase, though its degree of crystallinity was reduced with increased addition of the random copolymers. Thermogravimetry (TG) showed that the degradation temperatures varied systematically with blend composition. PVDF blends with either copolymer showed significant increase of fouling resistance. Membranes prepared from blends containing 10% P(MMA‐ran‐SB2VP) had the highest fouling resistance, with a fivefold decrease in protein adsorption on the surface, compared to homopolymer PVDF. They also exhibited higher pure water flux, and better oil removal in oil–water separation experiments. © 2018 Society of Chemical Industry     

Counterion dependent crystallization kinetics in blends of a perfluorosulfonate ionomer with poly(vinylidene fluoride)

Blends of poly(vinylidene fluoride) (PVDF) with a perfluorosulfonate ionomer, Nafion^®, have been prepared and examined in terms of the crystallization kinetics of the PVDF component. In blends of PVDF with Na⁺-form Nafion^®, the rates of bulk crystallization, as observed by DSC, and the spherulitic growth rates of the PVDF component, as observed using optical microscopy, were found to be very similar to that of pure PVDF. This behavior was attributed to the course phase separation of Na⁺-form Nafion^® from PVDF and melt incompatibility of the physically cross-linked ionomer with the crystallizable component. In this segregated state, the PVDF component of the blend is allowed to crystallize in pure phases that are isolated under the influence of Nafion^®. In contrast, when the ionomer was exchanged with more weakly interacting quaternary alkylammonium counterions, a decrease in both the rate of bulk crystallization and spherulitic growth was observed. Furthermore, the crystallization kinetics of PVDF in these blends was found to be dependent on the counterion size; as the size of counterions associated with the Nafion^® component increased, the rate of crystallization decreased. This behavior was attributed to a weakening of the electrostatic interactions in the ionomer phase and thus an increase in the extent of phase mixing with the larger ions.     

Crystalline transformations in spherulites of poly(vinylidene fluoride)

Parts of poly(vinylidene fluoride) spherulites of the α-phase undergo a transformation to the higher-melting γ-form when crystallized at high temperatures. As a rule, this transformation originates at the periphery of α-spherulites where their lamellae are in contact with, and oppositely directed to, lamellae of γ-spherulites; the latter are formed only at high temperatures. The transformation on then retreats towards the nuclei of α-spherulites at a slow (～10^?4μm s^?1), linear rate, which increases with temperature. At very high temperatures, this transformation is also initiated at some α-nuclei; a few of the α-spherulites also exhibit areas of the high-melting phase irregularly dispersed within their interiors. In samples crystallized below ～154°C, the transformation is of very limited extent, even after prolonged annealing at higher temperatures.     

Compatibility of poly(vinylidene fluoride) (PVDF)/polyamide 12 (PA12) blends

Poly(vinylidene fluoride) (PVDF)/polyamide 12 (PA12) blends showed new peaks in XRD profile with increasing PA12 and the crystallinity of PA12 significantly decreased with the addition of PVDF. PVDF showed three relaxation regions at about −40, 40, and 100°C, respectively, and glass transition temperature (T_g ) of PA12 increased in blends (10.8→30.14°C) and α‐relaxation of PVDF decreased from 100.26 to 86.46°C. Complex viscosities (η*) vs. composition curve showed a great positive deviation in PVDF‐rich and a small negative deviation in PA12‐rich blends. The N—H and C=O stretching band of PA12 shifted slightly toward higher wavelength, and from curve‐fitted data the area of hydrogen‐bonded C=O stretching bands of PA12 decreased with the addition of PVDF, especially in the 30/70 blend, implying the existence of interactions between the β‐hydrogen atom of PVDF and amide carbonyl group of PA12 in the blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1374–1380, 2000     

PVDF复合材料的流变行为研究

采用RC90 HAAKE转矩流变仪对PVDF复合材料与PVDF进行流变性能研究,结果显示,PVDF复合材料与PVDF一样属于非牛顿流体,具有典型的切力变稀行为,PVDF复合材料的粘流活化能和非牛顿指数n较PVDF高,说明PVDF复合材料对剪切速率的依赖性较PVDF小。     

1,3,5-Benzenetrisamide based nucleating agents for poly(vinylidene fluoride)

This paper presents 1,3,5-benzenetrisamides as colorless α-nucleating agents for poly(vinylidene fluoride). In order to screen a large variety of 1,3,5-benzenetrisamide derivatives with respect to their nucleating potential an efficient and reliable test based on polarized light microscopy was established. For selected promising compounds the concentration dependence of the PVDF crystallization temperature, the dissolution behavior of the additive in the polymer melt, and the crystallization of the additive from the polymer melt was investigated in a concentration range between 1 wt% (10,000 ppm) and 70 ppm. It was found, that only two of the investigated compounds were able to raise the crystallization temperature about 8 °C at a concentration of 140 ppm and 580 ppm, respectively. These trisamides have the advantage being soluble in the polymer melt, not featuring absorption of visible light and therefore allowing the preparation of uniform and colorless PVDF products.     

Effect of X-rays on poly(vinylidene fluoride) in X-ray photoelectron spectroscopy

The polymer poly(vinylidene fluoride) (PVDF) was irradiated with X-rays produced by a nonmonochromatic (MgKα) source and the structural and electronic PVDF surface modifications were studied by X-ray photoelectron spectroscopy (XPS). Changes in the shape and intensity of the C_1s and F_1s lines show that a PVDF degradation consisting of the polymer defluorination takes place. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:2125–2129, 1998     

Porous poly(vinylidene fluoride) membrane with highly hydrophobic surface

The preparation of very hydrophobic poly(vinylidene fluoride) (PVDF) membranes was explored by using two methods. The first one was the modified phase inversion method using a water/N,N‐dimethylacetamide (DMAc) mixture instead of pure water as a soft precipitation bath. The second method was a precipitation‐bath free method, that is, the PVDF/DMAc casting solution underwent gelation in the open air instead of being immersed into a precipitation bath. The morphology of the surface and cross section of the membranes was investigated by using scanning electron microscopy (SEM). It was found that the membranes exhibited certain micro‐ and nanoscale hierarchical roughness on the surface, which brought about an enhanced hydrophobicity of the membrane. The contact angle (CA) of the samples obtained by the second method was as high as 150° with water. The conventional phase inversion method preparing PVDF porous membrane using pure water as precipitation bath usually results in an asymmetric membrane with a dense skin layer having a CA close to that of a smooth PVDF surface. The modified approach avoided the formation of a skin‐layer and resulted in a porous and highly hydrophobic surface of PVDF. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1358–1363, 2005     

Crystal polymorphism in electrospun composite nanofibers of poly(vinylidene fluoride) with nanoclay

We investigated for the first time the morphology and crystal polymorphism of electrospun composite nanofibers of poly(vinylidene fluoride) (PVDF) with two nanoclays: Lucentite™ STN and SWN. Both nanoclays are based on the hectorite structure, but STN has organic modifier in between the layers of hectorite while SWN does not. PVDF/nanoclay was dissolved in N,N-dimethylformamide/acetone and electrospun into composite nanofiber mats with fiber diameters ranging from 50-800 nm. Scanning electron microscopy shows that addition of STN and SWN can greatly decrease the number of beads and make the diameter of the nanofibers more uniform due to the increase of electrospinning solution conductivity brought by the nanoclay. Infrared spectroscopy and X-ray diffraction confirm that both STN and SWN can induce more extended PVDF chain conformers, found in beta and gamma phase, while reducing the alpha phase conformers in electrospun PVDF/Nanoclay composite nanofibers. With the attached organic modifier, even a small amount of STN can totally eliminate the non-polar alpha crystal conformers while SWN cannot. The ionic organic modifier makes STN much more effective than SWN in causing crystallization of the polar beta and gamma phases of PVDF. An ion-dipole interaction mechanism, suggested by Ramasundaram, et al. is utilized to explain the crystal polymorphism behavior in electrospun PVDF/nanoclay composite nanofibers.     

聚碳酸酯对聚偏氟乙烯结构和结晶行为的影响

通过熔融共混法制备聚偏氟乙烯/聚碳酸酯（PVDF/PC）共混物,采用X线衍射仪（XRD）和差示扫描量热仪（DSC）表征共混物的结构、熔融和结晶行为.考察不同聚碳酸酯含量对聚偏氟乙烯晶体结构、熔点以及晶体完善程度等的影响.同时通过Avram i方程和结晶速率系数的研究,探讨PC对PVDF非等温结晶动力学的影响.研究结果表明：PC的掺杂没有改变PVDF的晶体结构,但是高PC质量分数（70%以上）却不利于PVDF晶体的生成;随着PC质量分数的增加,生成的PVDF晶体完善程度逐渐降低;当PC质量分数在70%以下时,PC起到类似成核剂作用,提高PVDF结晶速率.     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

Strain rate mediated microstructure evolution for extruded poly(vinylidene fluoride) polymer films under uniaxial tension

The deformation and fracture mechanism during uniaxial tension under controlled strain rates are investigated for extruded poly(vinylidene fluoride) (PVDF) polymer films at room temperature. It was found that both the longitudinal and transversal film‐samples exhibited pronounced strain rate effect, that is, the yield stress increases while the fracture strain decreases with the increasing of strain rates. For the longitudinal film samples, phase transformation from the nonpolar α‐phase to the polar β‐phase occurs during the uniaxial tension, and the extent of the phase transformation enhances when the strain rate decreases. For the transversal film samples, no phase transformation was detected in all tested strain rates. By combining the stress–strain behavior and the X‐ray results, it can be inferred that the conformational change from α to β phase during uniaxial tension contributes to the higher fracture strain of the longitudinal films than that of the transversal films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1786–1790, 2007     

Change in crystallinity of poly(vinylidene fluoride) due to thermal evaporation

Dielectric properties are reported for thin transparent poly(vinylidene fluoride) (PVDF) films, with thickness less than 1 μm, obtained by the thermal evaporation technique. This technique had to be used with the utmost care and control over the temperature of the evaporation source to obtain transparent, undegraded films of PVDF. Capacitance and loss tangent measurements were carried out on these films in the frequency range of 20 Hz to 1 MHz and the temperature range of 25-160°C. It was found that the maximum in ϵ′-t plots at 1 kHz and tan δ-t plots at 100 Hz for these films appeared at 50 and 35°C, respectively, which are lower temperatures than those reported for solution cast PVDF films. This is attributed to the lowering of crystallinity in the thermally evaporated films. X-ray diffraction studies and IR studies also confirmed these observations. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 225–230, 1997     

FTIR microspectroscopy and DSC analysis of blends of poly(vinylidene fluoride) with isotactic and syndiotactic poly(methyl methacrylate)

Films of blends of poly(vinylidene fluoride) (PVDF) with isotactic and syndiotactic poly(methyl methacrylate) (i-PMMA and s-PMMA), obtained by casting tetrahydrofuran (THF) and dimethyl sulphoxide (DMSO) solutions onto BaF₂ windows, have been investigated by means of FTIR-microspectroscopy (FTIR-M), optical microscopy and differential scanning calorimetry (DSC). The study of the effect of the PMMA tacticity on the intermolecular interaction between the two components, as well as on the structure, morphology and thermal behaviour of these blends, is the object of this paper. On the basis of the major shift of the carbonyl band of i-PMMA in the mixtures, the occurrence of stronger interactions for PVDF/i-PMMA compared with PVDF/s-PMMA blends can be suggested. © 1998 SCI.