Synthesis of poly(styrene-co-acrylonitrile) copolymer brushes on silica nanoparticles through surface-initiated polymerization

In the present investigation, silica nanoparticles have been coated with poly(styrene-co-acrylonitrile) (SAN) copolymer brushes synthesized via surface-initiated atom transfer radical polymerization (ATRP). In the initial step, silica nanoparticles were functionalized with triethoxysilane-based ATR initiator, 6-(2-bromo-2-methyl) propionyloxy hexyl triethoxysilane. Successful formation of the covalent linkages between ATRP initiator and silica nanoparticles is further corroborated using thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS). The surface initiated ATRP of the styrene and the acrylonitrile mediated by a copper complex was carried out using the initiator fixed silica nanoparticles in the presence of a sacrificial (free) initiator. The polymerization is preceded in a living manner in all examined cases, producing nanoparticles coated with well-defined poly(styrene-co-acrylonitrile) (SAN) brushes with molecular weight in the range of 12–22 kDa. SAN-grafted silica nanoparticles were characterized using TGA which showed significant weight loss in the temperature range of 340–420 °C confirming the formation of the polymer brushes on the surface with graft densities in the range of 0.109–0.190 chains/nm². Successful formation of the SAN copolymer brushes are further characterized by FTIR and proton nuclear magnetic resonance spectroscopy techniques. Differential scanning calorimetric studies revealed that the SAN copolymer grafted onto silica nanoparticles exhibits higher glass transition temperatures than free SAN copolymers. Transmission electron microscopy and dynamic light scattering studies revealed that the SAN copolymer-grafted silica nanoparticles showed relatively fine dispersion in organic solvents such as tetrahydrofuran, when compared to bare silica nanoparticles.     

Synthesis and characterization of well-defined hydrophilic block copolymer brushes by aqueous ATRP

Homopolymer brushes of poly(N,N-dimethylacrylamide) (PDMA), poly(methoxyethylacrylamide) (PMEA) and poly(N-isopropylacrylamide)(PNIPAM) grown on atom transfer radical polymerization (ATRP) initiator functionalized latex particles were used as macroinitiators for the synthesis of PDMA-b-PNIPAM/PMEA, PMEA-b-PDMA/PNIPAM and PNIPAM-b-PDMA block copolymer brushes by surface initiated aqueous ATRP. The grafted homopolymer and block copolymer brushes were analyzed for molecular weight, molecular weight distribution, chain grafting density, composition and hydrodynamic thickness (HT) using gel permeation chromatography-multi-angle laser light scattering, ¹H NMR, particle size analysis and atomic force microscopy (AFM) techniques. The measured graft molecular weight increased following the second ATRP reaction in all cases, indicating the second block had been added. Chain growth depended on the nature of the monomer used for block copolymerization and its concentration. Unimodal distribution of polymer chains in GPC with non-overlap of molar mass-elution volume curves implied an efficient block copolymerization. This was supported by the increase in HT measured by particle size analysis, equilibrium thickness observed by AFM and the composition of the block copolymer layer by ¹H NMR analysis, both in situ and on cleaved chains in solution. ¹H NMR analysis of the grafted latex and cleaved polymers from the surface demonstrated that accurate determination of the copolymer composition by this method is possible without detaching polymer chains from surface. Block copolymer brushes obey the same power law dependence of HT on molecular weight as homopolymer brushes in good solvent conditions. The NIPAM-containing block copolymer brushes were sensitive to changes in the environment as shown by a decrease in HT with increase in the temperature of the medium.     

Emulsion atom transfer radical polymerization of 2-ethylhexyl methacrylate

The emulsion atom transfer radical polymerization (ATRP) of 2-ethylhexyl methacrylate (EHMA) was carried out with ethyl 2-bromoisobutyrate (EBiB) as an initiator and copper bromide (CuBr)/4,4′-dinonyl-2,2′-bipyridyl (dNbpy) as a catalyst system. The effects of surfactant type and concentration, temperature, monomer/initiator ratio, and CuBr₂ addition on the system livingness, polymer molecular weight control, and latex stability were examined in detail. It was found that the polymerization systems with Tween 80 and Brij 98 as surfactants at 30 °C gave the best latex stability. The polymer samples prepared under these conditions had narrow molecular weight distributions (M_w/M_n=1.1-1.2) and linear relationships of number-average molecular weight versus monomer conversion.     

A novel method of surface-initiate atom transfer radical polymerization of styrene from silica nanoparticles for preparation of monodispersed core-shell hybrid nanospheres

A new kind of initiator, 3-(2-bromo-2-methylacryloxy)propyltriethysiliane (MPTS-Br), was prepared with a simply hydrobrominated commercial silane coupling agent (3-methacryloxy-proplytriethysilane, MPTS). It has been one-step self-assemble onto the surface of silica nanoparticles, and by using this initiator-modified nanoparticle (SiO₂-MPTS-Br) as macroinitiator for atom transfer radical polymerization (ATRP). Structurally well-defined homopolymer polystyrene (PS) and block polymer poly(styrene-b-methyl methacrylate) (PS-b-PMMA) chains were grown from the nanoparticles surface to yield individual particles composed of silica core and thick-coated polymer shell. The graft parameters could be calculated from the elemental analysis (EA) results, and linear plots of percentage of grafting (PG%) and conversion of monomer (C%) versus polymerizing time were achieved, respectively. Narrow molecular weight distribution (M_w/M_n) for the graft polymer samples were characterized by the gel permeation chromatography (GPC). The graft polymerizations exhibited the characteristics of the controlled/“living” polymerization. The glass transition temperature (T_g) of SiO₂-g-PS after polymerizing time of 24 h was found about 133 °C which was different from the polymer not grafted on the silica at 102 °C by the differential scanning calorimetry (DSC) analysis. The products were also characterized by FT-IR, XPS and TEM. The robustness and simplicity of this method may make large-scale manufacture of these polymer-coated nanospheres possible.     

Atom transfer radical polymerized MR fluids

A novel magnetorheological fluid, in which the surface of iron particles is coated with poly(butyl acrylate) by surface-initiated atom transfer radical polymerization (ATRP), is investigated. The polymer coating procedure includes two steps, which are immobilization of initiator: 2-(4-chlorosulfonylphenyl)-ethyltrichlorosilane (CTCS) on the iron particles' surface and graft polymerization of butyl acrylate from the surface. The surface coating is characterized by FTIR and SEM. This magnetorheological fluid has controllable off-state viscosity and high shear yield stress. Coating polymer on the iron particles' surface by ATRP can significantly reduce iron particles' settling and improve stability of the MR fluid. Glass transition temperature is obtained using the step-scan DSC method. The molecular weight and conversion can be controlled by the molar ratio of monomer to initiator, reaction temperature and time. The reaction is first order determined by the plot of ln[M]₀/[M] against polymerization time.     

Atom transfer radical suspension polymerization of methyl methacrylate catalyzed by CuCl/bpy

Atom transfer radical suspension polymerization (suspension ATRP) of methyl methacrylate (MMA) was carried out using 1-chloro-1-phenylethane (1-PECl) as initiator, copper chloride/bipyridine (CuCl/bpy) as catalyst. The polymerization was accomplished with a mechanical agitator under the protection of nitrogen atmosphere. Apart from the dispersing agent (1% PVA), NaCl was also used in the water phase to decrease the diffusion of CuCl/bpy to water and the influence of the concentration of NaCl was investigated. Subsequently, the kinetic behavior of the suspension ATRP of MMA at different temperatures was studied. At 90 and 95 °C, the polymerization showed first order with respect to monomer concentration until high conversion. The molecular weight (M_n) of the polymer increased with monomer conversion. However, at lower temperatures, different levels of autoacceleration was observed. The polymerization deviated from first order with respect to monomer concentration when the conversion was up to some degree. The lower the temperature was, the more the deviation displayed. On comparison with bulk ATRP of MMA, the rate of suspension ATRP was much faster.     

ICAR ATRP of methyl methacrylate catalyzed by FeCl3·6H2O/succinic acid

In this work, methyl methacrylate (MMA) was polymerized by initiator for continuous activator regeneration (ICAR) atom transfer radical polymerization (ATRP) method to obtain low molecular weight living polymers. The ATRP initiator was ethyl 2‐bromoisobutyrate, the catalyst ligand complex system was FeCl₃·6H₂O/succinic acid, and the conventional radical initiator 2,2′‐azobisisobutyronitrile was used as a thermal radical initiator. Polymers with controlled molecular weight were obtained with ppm level of Fe catalyst complex at 90°C in N,N‐dimethylformamide. The polymer was characterized by nuclear magnetic resonance (NMR). The molecular weight and molecular weight distribution of the obtained poly (methyl methacrylate) were measured by gel permeation chromatography method. The kinetics results indicated that ICAR ATRP of MMA was a “living”/controlled polymerization, corresponding to a linear increase of molecular weights with the increasing of monomer conversion and a relatively narrow polydispersities index. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

End-capped polystyrene with 8-hydroxyquinoline group by ATRP method

8-Hydroxyqunioline end-capped polystyrene was prepared through atom transfer free radical polymerization (ATRP) with 8-(5-chloromethyl) quinolyl acetate as initiator. The results indicated that this polymerization is a first order reaction with respect to monomer conversion. The molecular weight increased linearly with monomer consumption and very narrow distribution of molecular weight was obtained (polydispersity index less than 1.2). The FT-IR and NMR results show that the 8-hydroxyquinloine group was chemically bonded to the polymer end and there is nearly one 8-hydroxyquinoline group in per polymer chain. All those data show that polymerization of styrene at such conditions displayed living characters. The polymer with 8-hydroxyqquinoline end group reacted with triethylaluminum to form polymeric light-emitting complex and single layer LED was prepared by common spin-coating method. The peak wavelength of LED based on synthesized polymeric complex was around 570 nm.     

Synthesis of Polymer Grafted Magnetite Nanoparticle with the Highest Grafting Density via Controlled Radical Polymerization

Abstract  The surface-initiated ATRP of benzyl methacrylate, methyl methacrylate, and styrene from magnetite nanoparticle is investigated, without the use of sacrificial (free) initiator in solution. It is observed that the grafting density obtained is related to the polymerization kinetics, being higher for faster polymerizing monomer. The grafting density was found to be nearly 2 chains/nm² for the rapidly polymerizing benzyl methacrylate. In contrast, for the less rapidly polymerizing styrene, the grafting density was found to be nearly 0.7 chain/nm². It is hypothesized that this could be due to the relative rates of surface-initiated polymerization versus conformational mobility of polymer chains anchored by one end to the surface. An amphiphilic diblock polymer based on 2-hydroxylethyl methacrylate is synthesized from the polystyrene monolayer. The homopolymer and block copolymer grafted MNs form stable dispersions in various solvents. In order to evaluate molecular weight of the polymer that was grafted on to the surface of the nanoparticles, it was degrafted suitably and subjected to gel permeation chromatography analysis. Thermogravimetric analysis, transmission electron microscopy, and Fourier transform infrared spectroscopy were used to confirm the grafting reaction. Graphical Abstract   Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Synthesis and characterization of A-B-A triblock copolymers derived from chloro-telechelic poly(l-lactide): combining ring-opening polymerization (ROP) and atom transfer radical polymerization (ATRP)

Ring-opening polymerization (ROP) of l-lactide was combined with atom transfer radical polymerization (ATRP) to produce well-defined linear block copolymers. Poly(l-lactide) (PLLA) was synthesized via ROP using ethylene glycol as an initiator and stannous octoate as a catalyst. The isolated hydroxy-telechelic PLLA was reacted with thionyl chloride and pyridine in toluene to afford chloro-telechelic PLLA (Cl-PLLA-Cl). The latter was employed as a macroinitiator in the synthesis of A-B-A triblock copolymers having either tert-butyl acrylate or benzyl acrylate outer blocks. Outer-block molecular weight was targeted by the mole ratio of monomer (acrylate) to the PLLA chloride initiating sites. The actual incorporation of acrylate into the triblock copolymer was lower than the molar feed ratio as the copolymer became increasingly less soluble upon conversion of acrylate in all cases.     

Controlled polymerization of methylmethacrylate from fumed SiO2 nanoparticles through atom transfer radical polymerization

Atom transfer radical polymerization (ATRP) is a promising method to synthesize well‐defined polymer/inorganic nanoparticles. However, the surface‐initiated ATRP from commercially mass produced inorganic nanoparticles has seldom been studied. In this study, the surface‐initiated ATRP of methylmethacrylate (MMA) from commercially mass produced fumed silica (SiO₂) nanoparticles was investigated. Unlike the ATRP of MMA initiated from a free initiator, the controllability of ATRP of MMA from the surface of fumed silica nanoparticles was much better using ligand 2,2'‐bipyridine (bpy) than N,N,N′,N′′,N′′‐pentamethyldiethylenetriamine (PMDETA) as the initiator was immobilized on the surface of the SiO₂ nanoparticles and the presence of the SiO₂ nanoparticles made the CuCl/bpy catalyst system a homogeneous catalyst system and CuCl/PMDETA a heterogeneous one. The appropriate molar ratio of monomer and initiator was essential for preparing controlled PMMA/SiO₂ nanoparticles. The entire process of ATRP of MMA from the surface of SiO₂ nanoparticles was controllable when using bpy as ligand, xylene as solvent and with a monomer to initiator ratio of 300:1. The ¹H NMR results indicated that the PMMA on the surface of the SiO₂ was prepared via ATRP initiated from 4‐(chloromethyl)phenyltrimethoxysilane. The well‐defined PMMA/SiO₂ nanoparticles obtained have good thermal stability and are well dispersed in organic media as proved by TGA, dynamic light scattering and transmission electron microscopy. © 2013 Society of Chemical Industry     

Grafting of Poly(methyl methacrylate) Brushes from Magnetite Nanoparticles Using a Phosphonic Acid Based Initiator by Ambient Temperature Atom Transfer Radical Polymerization (ATATRP)

Poly(methyl methacrylate) in the brush form is grown from the surface of magnetite nanoparticles by ambient temperature atom transfer radical polymerization (ATATRP) using a phosphonic acid based initiator. The surface initiator was prepared by the reaction of ethylene glycol with 2-bromoisobutyrl bromide, followed by the reaction with phosphorus oxychloride and hydrolysis. This initiator is anchored to magnetite nanoparticles via physisorption. The ATATRP of methyl methacrylate was carried out in the presence of CuBr/PMDETA complex, without a sacrificial initiator, and the grafting density is found to be as high as 0.90 molecules/nm². The organic–inorganic hybrid material thus prepared shows exceptional stability in organic solvents unlike unfunctionalized magnetite nanoparticles which tend to flocculate. The polymer brushes of various number average molecular weights were prepared and the molecular weight was determined using size exclusion chromatography, after degrafting the polymer from the magnetite core. Thermogravimetric analysis, X-ray photoelectron spectra and diffused reflection FT-IR were used to confirm the grafting reaction.     

Ultra high molar mass poly[2-(dimethylamino)ethyl methacrylate] via atom transfer radical polymerization

Well-defined high molecular weight poly[2-(dimethylamino)ethyl methacrylates] [poly(DMAEMA)s] with molar masses up to ∼1×10⁶ g/mol were successfully synthesized via atom transfer radical polymerization (ATRP). This was achieved by using p-toluenesulfonyl chloride(p-TsCl)/CuCl/1,1,4,7,10,10-hexamethyl-triethylenetetramine(HMTETA) initiator/catalyst complex in methanol/water mixture. Well-controlled/‘living’ behavior was demonstrated throughout the reaction, up to high monomer conversion. The PDI value remained low at 1.26 even for a polymer with very high molecular weight at 1.1×10⁶ g/mol. We believe this is the first successful case where controlled ATRP produces a polymer with molar mass exceeding a million!     

Atom transfer radical polymerization of styrene initiated by 2-(4-chloromethyl-phenyl)-benzoxazole with high activity and fluorescent property

Functionalized polystyrene (PSt) was synthesized utilizing atom transfer radical polymerization (ATRP), which was conducted by using 2-(4-chloromethyl-phenyl)-benzoxazole (CMPB) as initiator, CuCl/PMDETA as catalyst, and cyclohexanone as solvent. The mechanism of ATRP was proved by characterizing the structure of PSt via ¹H NMR and preparing of PSt-b-PMMA block copolymer. The polymerization showed first order with respect to monomer concentration and relatively narrow polydispersity (M_w/M_n range from 1.30 to 1.50). Factors such as different reaction temperatures, mole ratio of monomer to initiator and so on, which can affect the ATRP system, were discussed in the paper. Moreover, CMPB showed high activity and could initiate styrene polymerization even at ambient temperature. The optical property of initiator was well preserved in the obtained PSt, and the end-functionalized PSt exhibited strong fluorescent emission at 351 nm.     

Synthesis and characterization of pH/temperature-sensitive block copolymers via atom transfer radical polymerization

In order to prepare well-defined pH-sensitive block copolymers with a narrow molecular weight distribution (MWD), we synthesized a pH-sensitive block copolymer via atom transfer radical polymerization (ATRP) of sulfamethazine methacrylate monomer (SM) and amphiphilic diblock copolymers by the ring-opening polymerization of d,l-lactide/?-caprolactone (LA/CL), and their sol-gel phase transition was investigated. SM, which is a derivative of sulfonamide, was used as a pH responsive moiety, while PCLA-PEG-PCLA was used as a biodegradable, as well as a temperature sensitive one, amphiphilic triblock copolymer. The pentablock copolymer, OSM-PCLA-PEG-PCLA-OSM, was synthesized using Br-PCLA-PEG-PCLA-Br as an ATRP macroinitiator. The number average molecular weights of SM were controlled by adjusting the monomer/initiator feed ratio. The macroinitiator was synthesized by the coupling of 2-bromoisobutyryl bromide with PCLA-PEG-PCLA in the presence of triethyl amine catalyst in dichloromethane. The resultant block copolymer shows a narrow polydispersity. The block copolymer solution shows a sol-gel transition in response to a slight pH change in the range of 7.2-8.0. Gel permeation chromatography (GPC) and NMR were used for the characterization of the polymers that were synthesized.     

Multicomponent vapor deposition polymerization of poly(methyl methacrylate) in an axisymmetric vacuum reactor

An axisymmetric, multicomponent initiated chemical vapor deposition (i-CVD) apparatus was designed to study the vapor-phase growth of glassy poly(methyl methacrylate) (PMMA) films. Preheated monomer (methyl methacrylate) and initiator (t-butyl peroxide) vapors were metered into a pressure-controlled reaction chamber. Inside the chamber, gases pass through a high-temperature hot-zone where primary free radicals are formed. The gas mixture then condenses and polymerizes on a back-cooled target substrate. Key reactor operating parameters were systematically varied to understand film growth kinetics. These include the hot-zone temperature, reactor base-pressure, substrate temperature, and the monomer/initiator molar feed ratio. Polymer deposition requires good thermal contact between feed gases and the hot-zone. Packed with glass beads, the hot-zone reactor resulted in more efficient initiation and film growth. Experiments also show that polymer deposition rate is limited by thermal initiation of primary free radicals, transport of primary free radicals to the target substrate, and by monomer adsorption. Size exclusion chromatography of deposited polymers is used to relate molecular weight to the monomer-to-initiator feed ratio. The addition of a third vapor component, 1-butanol, was also found to affect polymer molecular weight.     

Direct Controlled Polymerization of Ionic Monomers by Surface-Initiated ATRP Using a Fluoroalcohol and Ionic Liquids

Surface-initiated atom transfer radical polymerization (ATRP) of (2-methacryloyloxyethyl)trimethylammonium chloride (MTAC), 3-(N-2-methacryloyloxyethyl-N,N-dimethyl) ammonatopropanesulfonate) (MAPS), and 2-methacryloyloxyethyl phosphorylcholine (MPC) was carried out in 2,2,2-trifluoroethanol (TFE) containing a small amount of 1-hexyl-3-methylimidazolium chloride at 60 °C to produce well-defined ionic polymer brushes and the corresponding free polymers with predictable number-average molecular weight (M_n, 1×10⁴−3×10⁵ g mol⁻¹) and narrow molecular weight dispersity (M_w/M_n<1.2). A first-order kinetic plot for ATRP of MTAC and MAPS revealed a linear relationship between the monomer conversion index (ln([M]₀/[M])) and polymerization time. Reduction in polymerization rates was observed with an increase in ionic liquid concentration. The M_n of both poly(MTAC) and poly(MAPS) increased in proportion to the conversion. The sequential polymerization of MAPS initiated with the chain ends of poly(MAPS) produced the postpolymer with quantitative efficiency. The thickness of the polymer brush was controllable from 5 to 100 nm based on the M_n of the polymer. These results suggest the successful control of the polymerization of sulfobetaine-type methacrylates owing to the TFE and ionic liquids. In particular, the high affinity of TFE for the sulfobetaine monomers and polymers yielded a homogeneous polymerization media to improve surface-initiated polymerization generating the polymer brushes on the substrate surface as well as the free polymers formed in the solution. The effect on ATRP of the chemical structure of ionic liquids and ligands for copper catalyst was also investigated.     

Fe‐mediated ICAR ATRP of styrene and acrylonitrile in polyethylene glycol

In this contribution, random copolymers of p(styrene‐co‐acrylonitrile) via initiators for continuous activator regeneration (ICAR) in atom transfer radical polymerization (ATRP) (ICAR ATRP) of styrene and acrylonitrile (SAN) were synthesized at 90°C in low molecular weight polyethylene glycol (PEG‐400) using CCl₄ as initiator, FeCl₃·6H₂O as catalyst, succinic acid as ligand and thermal radical initiator azobisisobutyronitrile (AIBN) as thermal free radical initiator. In this system, well‐defined copolymer of SAN was achieved. The kinetics results showed that the copolymerization rate obeyed first‐order kinetics model with respect to the monomer concentration, and a linear increase of the molecular weights with the increasing of monomer conversion with narrow molecular weight distribution was observed in the range of 1.1–1.5. The conversion decreased with increasing the amount of FeCl₃·6H₂O and increased with increasing the molar ratio of [St]₀/[AN]₀/[CCl₄]₀ and temperature. AIBN has a profound effect on the polymerization. The activation energy was 55.67 kJ mol^?1. The living character of copolymerization was confirmed by chain extension experiment. The resultant random copolymer was characterized by ¹H‐NMR and GPC. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40135.     

Graft polymerization of vinyl acetate onto silica

The free‐radical graft polymerization of vinyl acetate onto nonporous silica particles was studied experimentally. The grafting procedure consisted of surface activation with vinyltrimethoxysilane, followed by free‐radical graft polymerization of vinyl acetate in ethyl acetate with 2,2′‐azobis(2,4‐dimethylpentanenitrile) initiator. Initial monomer concentration was varied from 10 to 40% by volume and the reaction was spanned from 50 to 70°C. The resulting grafted polymer, which was stable over a wide range of pH levels, consisted of polymer chains that are terminally and covalently bonded to the silica substrate. The experimental polymerization rate order, with respect to monomer concentration, ranged from 1.61 to 2.00, consistent with the kinetic order for the high polymerization regime. The corresponding rate order for polymer grafting varied from 1.24 to 1.43. The polymer graft yield increased with both initial monomer concentration and reaction temperature, and the polymer‐grafted surface became more hydrophobic with increasing polymer graft yield. The present study suggests that a denser grafted polymer phase of shorter chains was created upon increasing temperature. On the other hand, both polymer chain length and polymer graft density increased with initial monomer concentration. Atomic force microscopy–determined topology of the polymer‐grafted surface revealed a distribution of surface clusters and surface elevations consistent with the expected broad molecular‐weight distribution for free‐radical polymerization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 300–310, 2003     

Synthesis, characterization, and controllable drug release of dendritic star-block copolymer by ring-opening polymerization and atom transfer radical polymerization

A series of well-defined dendritic star-block copolymers were successfully synthesized by combination of living ring-opening polymerization (ROP) and atom transfer radical polymerization (ATRP) with the hydroxyl-terminated dendrimer polyester. Dendritic star-shaped poly(l-lactide)s (PLLAs) were prepared by bulk polymerization of l-lactide (l-LA) with dendrimer polyester initiator and tin 2-ethylhexanoate catalyst. The number-average molecular weight of these polymers linearly increased with the molar ratio of l-LA to dendrimer initiator. Dendritic star-shaped PLLA was converted into a PLLABr macroinitiator with 2-bromopropionyl bromide. Dendritic star-block copolymers could be obtained via ATRP of 2-(N,N-dimethylamino)ethyl methacrylate (DMAEMA). The molecular weight distributions of these copolymers were narrow. The molecular weights of dendritic star-shaped polymers and star-block copolymers could be controlled by the molar ratios of monomer to initiator and monomer conversion. The thermal properties of these dendritic star-shaped polymers and star-block copolymers were investigated. The behavior of model drug chlorambucil release from the copolymer indicated that the rate of drug release could be effectively controlled by altering the pH values of the environment.