合成温度对LiMn1.95Mg0．05O4结构与性能的影响

用柠檬酸辅助溶胶一凝胶法在不同温度下合成了LiMn1.95Mg0．05O4正极材料。用X射线衍射、充放电测试以及电化学阻抗谱分析技术研究了不同合成温度对LiMn1.95Mg0．05O4结构和电化学性能的影响。结果表明：合成温度对LiMn1.95Mg0．05O4正极材料的晶相结构、电化学性能有显著影响,LiMn1.95Mg0．05O4尖晶石相的生成和长大与其合成的温度有密切的关系,合成的最佳温度为750℃;在750℃条件下合成的LiMn1.95Mg0．05O4具有较高的电化学活性和较好的晶相结构;高温合成有利于提高LiMn1.95Mg0．05O4正极材料的放电容量,低温合成有利于提高其循环性能。     

Surface modification of LiCo0. 05Mn1.95O4 cathode by coating with SiO2-TiO2 composite

1　INTRODUCTIONSincethefirstcommercializationbySonyCorpo rationintheearly 1990s ,thelithium ionbattery(LIB)hasbecomeamajorproducttodominatethemarketforsmallrechargeablebatteries .Further more ,Li ionbatteriesareexpectedtobeusedasalarge scaleenergystoragedeviceforelectricvehices(EV ) [1] .ThoughvarioustypesofcathodematerialssuchasLiCoO2 ,LiNiO2 ,LiMn2 O4 ,andsubstitutedtran sitionmetaloxidesarecurrentlyusedincommercial izedLi ionbatteries[2 ,3] ,LiCoO2 inthesecathodematerialsismost…     

Al2O3包覆LiNi0.03Co0.05Mn1.92O4正极材料的制备及其电化学性能

以Al(NO3)3?9H2O为包覆原料,通过燃烧法制备得到LiNi0.03Co0.05Mn1.92O4@Al2O3正极材料。通过X射线衍射(XRD),场发射扫描电子显微镜(FESEM)和透射电镜(TEM)等表征手段对材料的结构和形貌进行分析,并通过恒电流充放电、循环伏安(CV)、交流阻抗(EIS)等测试分析材料的电化学性能。结果表明,Al2O3包覆没有改变LiNi0.03Co0.05Mn1.92O4的尖晶石型结构,包覆层厚度约10.6nm。LiNi0.03Co0.05Mn1.92O4@Al2O3正极材料电化学性能得到了明显改善,1 C和10 C倍率下初始放电比容量分别为119.9 mAh?g-1和106.3 mAh?g-1,充放电循环500次后容量保持率分别为88.4%和78.2%,而未包覆的LiNi0.03Co0.05Mn1.92O4在1 C和10 C倍率下初始放电比容量分别为121.2 mAh?g-1和104.0 mAh?g-1,500次循环后容量保持率分别为84.1%和67.6%。LiNi0.03Co0.05Mn1.92O4@Al2O3活化能为32.92 kJ?mol-1,而未包覆材料的活化能为36.24 kJ?mol-1,包覆有效降低了材料Li+扩散所需克服的能垒,提高了材料的电化学性能。     

Structure and electrochemical performance of spinel LiMn2O4 synthesized by mechanochemical process

1　INTRODUCTIONLithium ion battery was used in many areasbecause of its high voltage, high energy densityand long cycle life and so on. Spinel lithium man ganese oxide was one of the most promising mate rials in term of its environmental benign, low cost,easy preparation and temperature safety. Mainproblem is the poor cycle life. As we all know thatboth the structure and electrochemical performanceof material strongly depended on the preparingmethod and starting…     

稀土元素对LiMn_2O_4电极材料相结构及性能的影响

采用X射线衍射仪、扫描电子显微镜、电池测试系统等研究了不同稀土掺杂元素La、Ce、Nd等对Pechini法合成的LiMn2O4材料的相结构、形貌及电化学性能的影响规律.结果表明,合成的LiMn2O4、LiLa0.03Mn1.97O4、LiLa0.01Ce0.01Nd0.01Mn1.97O4样品具有纯尖晶石型LiMn2O4结构,LiLa0.015Ce0.015Mn1.97O4样品由LiMn:O.相及微量杂质相CeO2组成;样品呈规则的近球形或球形,其粒径范围为0.5～2.5μm.稀土元素取代使LiMn2O4材料的初始容量略有降低、循环稳定性能有较大增加,LiMn2O4、LiLa0.03Mn1.97O4、LiLa0.015Ce0.015Mn1.97O4、LiLa0.01Ce0.01Nd0.01Mn1.97O42样品的初始容量分别为126.0、120.0、117.3、124.0 mA·h/g,经30次循环充放电后的容量分别为88.9、102.7、101.6、109.1 mA·h/g.     

Mg、F复合掺杂尖晶石LiMg0.1Mn1.9O3.95F0.05的合成和电化学行为研究

以己二酸为配位体采用溶胶-凝胶法合成了LiMn2O4,Mg掺杂或Mg和F复合掺杂的尖晶石锂镁氧化物正极材料.对合成出的样品采用X-射线衍射仪、X-光电子能谱、扫描显微电子镜、循环伏安测试和充放电测试仪进行了详细的研究.X-射线衍射结果表明,所有的样品都具有相同的纯尖晶石相,LiMg0.1Mn1.9O4和LiMg0.1Mn1.9O3.95F0.05与LiMn2O4的样品相比,具有较小的晶格参数和晶胞体积.X-光电子能谱试验结果表明,在LiMn2O4中,Mn3 和Mn4 的相对量分别为50.2%和49.8%,而LiMg0.1Mn1.9O3.95F0.05中Mn3 和Mn4 的相对量分别为48.4%和51.6%.扫描电镜结果显示,LiMg0.1Mn1.9O3.95F0.05颗粒尺寸略小、尺寸分布窄,形态结构更为规整.循环伏安实验显示,Mg和F复合掺杂的尖晶石具有更好的可逆性.LiMn2O4,LiMg0.1Mn1.9O4,LiMg0.1Mn1.9O3.95F0.05样品的首次放电能量和能量保持率分别为123、111、114 mAh·g-1和86.5%、92.3%、90.9%,且LiMg0.1Mn1.9O4和LiMg0.1Mn1.9O3.95F0.05具有比LiMn2O4更高的库仑效率.     

Synthesis and characterization of multidoped lithium manganese oxide spinel LiCo0.02La0.01Mn1.97O3.98Cl0.02

1 Introduction The cathode material plays an important role in the performance of lithium ion batteries. Lithium transition metal compounds with layered and spinel structure are favourites among cathode materials for lithium rechargeable batteries. In thi…     

Synthesis and electrochemical properties of Al-doped LiVPO4F cathode materials for lithium-ion batteries

Al-doped LiVPO4F cathode materials LiAlxV1-xPO4F were prepared by two-step reactions based on a car-bothermal reduction （CTR） process. The properties of the Al-doped LiVPO4F were investigated by X-ray diffraction （XRD）,scanning electron microscopy （SEM）,and electrochemical measurements. XRD studies show that the Al-doped LiVPO4F has the same triclinic structure （space group p-↑1 ） as the undoped LiVPO4F. The SEM images exhibit that the particle size of Al-doped LiVPO4F is smaller than that of the undoped LiVPO4F and that the smallest particle size is only about 1 μm. The Al-doped LiVPO4F was evaluated as a cathode material for secondary lithium batteries,and exhibited an improved reversibility and cycleability,which may be attributed to the addition of Al^3＋ ion by stabilizing the triclinic structure.     

Synthesis and electrochemical properties of Th-doped LiMn2O4 powders for lithium-ion batteries

To improve the cycle performance of eco-friendly and cost-effective spinel LiMN2O4 as the Li secondary batteries, the Th-doped LiThxMn1-xO4 spinel powers were synthesized by solid-state method. The starting materials, Li2CO3,MnO2 and Th(NO3)4·4H2O, were mixed uniformly using a traditional ball milling, which resulted in a uniform particle size distribution in the mixed powers. Tests of X-ray diffraction, SEM, impedance spectra and charge-discharge were carried out for LiThxMn1-xO4 cathode materials. Results show that the synthesized LiTh0.01Mn1.99O4 material exhibits standard spinel structure, regular particle morphology and excellent property of charge-discharge for big current. The capacity retention of the material modified by doping Th is more than 85.1% of the first discharge specific capacity of 111.5 mAh·g -1 after 20 cycles at the current rate 1C, while the pristine LiMN2O4 is only 57% of the first discharge specific capacity of 110.2 mAh·g-1 after the same cycles at the same current rate.     

Surface modification and characterization of F-Co doped spinel LiMn2O4

Spinel LiCo0.09Mn1.91O3.92F0.08 as cathode material was modified with LiCoO2 by the sol-gel method, and the crystal structure, morphology and electrochemical performance were characterized with XRD, SEM, EDS, AAS and charge-discharge test in this paper. The results show that a good clad coated on parent material can be synthesized by the sol-gel method, and the materialswith modification have perfect spinel structure. LiCo0.09Mn1.91O3.92F0.08 materials coated by LiCoO2 improve the stability of crystal structure and decrease the dissolution of Mn into electrolyte. With the LiCoO2 content increasing, the specific capacity and cycle performance of samples are improved. The capacity loss is also suppressed distinctly even at 55 ℃.     

模拟废旧锂离子电池湿法冶金浸出液再生铝掺杂LiNi0.5Co0.2Mn0.3O2正极材料

采用共沉淀法制备均相Al掺杂的LiNi0.5Co0.2Mn0.3O2正极材料,以利用Al对再生镍钴锰(NCM)正极材料的正面改性作用,并改善锂离子电池回收过程中繁琐和高成本的除杂过程.当浸出液中的Al3+含量为过渡金属(Ni、Co和Mn)总量的1％(摩尔分数)时,制备的Al掺杂NCM正极材料中晶格氧和Ni2+的浓度增加...     

LiMgxNi0.5-xMn1.5O4的制备和电化学性能

为改善LiNi0.5Mn1.5O4的电化学性能,采用流变相法合成掺镁的锂离子电池正极材料LiMgxNi0.5-xMn1.5O4(x=0,0.05,0.1)。XRD测试结果表明所得材料仍为尖晶石结构。电化学性能测试结果显示:当x取值0.1,在3.5～4.9V电压范围内进行充放电循环时,材料LiMg0.1Ni0.4Mn1.5O4具有较好的循环性能,1C充放电时,初始放电比容量可达110.22mAh/g,30次循环后容量衰减率仅为7.7%。     

Synthesis and electrochemical performance of 5V spinel LiNi0.5Mn1.5O4 prepared by solid-state reaction

Spinel compound LiNi0.5Mn1.5O4 with high capacity and high rate capability was synthesized by solid-state reaction. At first, MnCl2·4H2O and NiCl2·6H2O were reacted with (NH4)2C2O4·H2O to produce a precursor via a low-temperature solid-state route, then the precursor was reacted with Li2CO3 to synthesize LiNi0.5Mn1.5O4. The effects of calcination temperature and time on the physical properties and electrochemical performance of the products were investigated. Samples were characterized by thermal gravimetric analysis(TGA), scanning electron microscopy(SEM), X-ray diffractometry(XRD), charge-discharge tests and cyclic voltammetry measurements. Scanning electron microscopy(SEM) image shows that as calcination temperature and time increase, the crystallinity of the samples is improved, and their grain sizes are obviously increased. It is found that LiNi0.5Mn1.5O4 calcined at 800 ℃ for 6 h exhibits a typical cubic spinel structure with a space group of Fd3m. Electrochemical tests demonstrate that the sample obtained possesses high capacity and excellent rate capability. When being discharged at a rate as high as 5C after 30 cycles, the as-prepared LiNi0.5Mn1.5O4 powders can still deliver a capacity of 101 mA-h/g, which shows to be a potential cathode material for high power batteries.     

Preparation and electrochemical properties of LiMn1.95M0.05O4 （M=Cr, Ni）

The preparation process and electrochemical properties of LiMn2O4 and LiMnl.95M0.05O4 （M = Cr, Ni） were studied. The results show that the decomposition temperature range of xerogel prepared with lithium acetate and manganese acetate as raw rnaterials is large and the decomposition speed is slow. Oxygen consumed is apt to get a prompt supplement during the preparation of LiMn2O4, and carbonization of the organic matter can be reduced or avoided, which is favorable to the combination of lithium and manganese. Using lithium acetate, manganese acetate, chromium nitrate, and nickel nitrate as raw materials and adopting the citric acid complexing method, it has been found that the prepared powders have high purity, high quality stability, and even doping characters. With the increase of sintering temperature, the particle size and crystal lattice constant of LiMn1.95M0.05O4 （M = Cr, Ni） enhance. However, the purity of the product is relatively high and has no obvious change, which is advantageous to the control of the quality of LiMn1.95M0.0504 （M = Cr, Ni）. Doping with a small amount of Cr3. and Ni^2＋ can stabilize the spinel structure of LiMn2O4, suppress the Jahn-Teller effect, and improve the cycling properties but reduce the initial capacity.     

5 V正极材料LiNi0.5Mn1.5O4的草酸共沉淀法合成及性能

通过草酸共沉淀法成功合成了5 V正极材料LiNi0.5Mn1.5O4,采用XRD、SEM、充放电试验和循环伏安法对合成产物进行表征。XRD和SEM分析结果表明,所合成的正极材料LiNi0.5Mn1.5O4具有立方尖晶石结构（空间群为Fdˉ3 m）,结晶度高,粒度适中且比较均匀。电化学测试结果表明,合成产物具有优良的电化学性能,它仅在4.7 V附近有一个放电平台,0.1 C的放电容量高达133 mAh/g,50次循环后放电容量仍保持在128 mAh/g以上,1和3 C的放电容量在30次循环后也分别保持在122和101 mAh/g以上     

Synthesis and physicochemical properties of LiLa0.01Mnt.99O3.99F0.01 cathode materials for lithium ion batteries

Spinel lithium manganese oxide cathode materials were synthesized using the ultrasonic-assisted sol-gel method.The synthesized samples were investigated by differential thermal analysis (DTA) and thermogravimetry (TG),powder X-ray diffraction (XRD),scanning electron microscopy (SEM),cyclic voltammetry (CV),and the charge-discharge test.TG-DTA shows that significant mass loss occurs in two temperature regions during the synthesis of LiLa0.01Mn1.99O3.99F0.01.XRD data indicate that all samples exhibit the same pure spinel phase,and LiLa0.01Mn1.99O3.99F0.01 and LiLa0.01Mn1.99O4 samples have a better crystallinity than LiMn2O4. SEM images indicate that LiLa0.01Mn1.99O3.99F0.01 has a slightly smaller particle size and a more regular morphology structure with narrow size distribution.The charge-discharge test reveals that the initial capacities of LiMn2O4,LiLa0.01Mn1.99O4,and LiLa0.01Mn1.99O3.99F0.01 are 130,123,and 126 mAh·g-1,respectively,and the capacity retention rates of the initial value,after 50 cycles,are 84.8%,92.3%,and 92.1%,respectively.The electrode coulomb efficiency and CV reveal that the electrode synthesized by the ultrasonic-assistexi sol-gel (UASG) method has a better reversibility than the electrode synthesized by the sol-gel method.     

Effects of Na+ doping on crystalline structure and electrochemical performances of LiNi0.5Mn1.5O4 cathode material

Pristine LiNi_0.5Mn_1.5O₄ and Na-doped Li_0.95Na_0.05Ni_0.5Mn_1.5O₄ cathode materials were synthesized by a simple solid-state method. The effects of Na⁺ doping on the crystalline structure and electrochemical performance of LiNi_0.5Mn_1.5O₄ cathode material were systematically investigated. The samples were characterized by XRD, SEM, FT-IR, CV, EIS and galvanostatic charge/discharge tests. It is found that both pristine and Na-doped samples exhibit secondary agglomerates composed of well-defined octahedral primary particle, but Na⁺ doping decreases the primary particle size to certain extent. Na⁺ doping can effectively inhibit the formation of Li_xNi_1–xO impurity phase, enhance the Ni/Mn disordering degree, decrease the charge-transfer resistance and accelerate the lithium ion diffusion, which are conductive to the rate capability. However, the doped Na⁺ ions tend to occupy 8a Li sites, which forces equal amounts of Li⁺ ions to occupy 16d octahedral sites, making the spinel framework less stable, therefore the cycling stability is not improved obviously after Na⁺ doping.     

共沉淀法制备LiNi0.8Co0.1Mn0.1O2过程中加料速度对其性能的影响

采用共沉淀法制备Ni0.8Co0.1Mn0.1(OH)2前驱体,与LiOH.H2O混合后在氧气气氛中焙烧得到LiNi0.8Co0.1Mn0.1O2正极材料,探讨共沉淀反应过程中快速加料和慢速加料制度对前驱体形貌和LiNi0.8Co0.1Mn0.1O2正极材料性能的影响。通过X射线衍射(XRD)、扫描电镜(SEM)和电化学测试对样品进行表征。结果表明:慢速加料法减小了材料的粒径,合成了平均粒径在0.5μm左右的球形Ni0.8Co0.1Mn0.1(OH)2前驱体,且粒径分布比较集中;所合成LiNi0.8Co0.1-Mn0.1O2正极材料具有良好的层状结构,且无杂相存在;缓慢加料法得到的样品的电化学性能有很大提高,在0.1 C、0.5 C和1 C下首次放电比容量分别达到223.5、194.3和190.7 mA.h/g,循环30次后,容量保持率为80.09%、80.80%和85.84%。     

球形磷酸铁锂正极材料制备中试研究

用湿法球磨-喷雾干燥法制备LiFe0.98Mg0.02PO4/C复合正极材料;用激光粒度分析仪、X射线衍射仪、扫描电镜和恒流充放电等对前驱体和磷酸铁锂样品进行表征;考察不同球磨工艺对磷酸铁锂颗粒形貌、粒度分布、振实密度和电化学性能的影响。结果表明:用湿法球磨-喷雾干燥法可以制得球形颗粒、高振实密度且电化学性能优良的磷酸铁锂正极材料,原料经粗磨后再超细球磨制得的材料性能更佳,振实密度达1.67 g/cm3,在0.1 C、0.5 C和1.0 C倍率下的首次放电比容量分别为151、143和132 mA·h/g。     

Electrochemical performance of LiFePO4 cathode material for Li-ion battery

In the search for improved materials for rechargeable lithium batteries, LiFePO4 offers interesting possibilities because of its low raw materials cost, environmental friendliness and safety. The main drawback with using the material is its poor electronic conductivity and this limitation has to be overcome. Here Al-doped LiFePO4/C composite cathode materials were prepared by a polymer-network synthesis technique. Testing of X-ray diffraction, charge-discharge, and cyclic voltammetry were carried out for its performance. Results show that Al-doped LiFePO4/C composite cathode materials have a high initial capacity, good cycle stability and excellent low temperature performance. The electrical conductivity of LiFePO4 material can be obviously improved by doping Al. The better electrochemical performances of Al-doped LiFePO4/C composite cathode materials have a connection with its conductivity.