Advantage of further scaling in gate dielectrics below 0.5 nm of equivalent oxide thickness with La2O3 gate dielectrics

N-type metal-oxide-semiconductor field-effect transistor (MOSFET) with an equivalent oxide thickness (EOT) of 0.37 nm has been demonstrated with La₂O₃ as a gate dielectric for the first time. Despite the existence of parasitic capacitances at gate electrode and inversion layer in the channel, a sufficient drain current increment in both linear and saturation regions have been observed, while scaling the gate oxide from 0.48 to 0.37 nm in EOT. Therefore, continuous scaling of EOT below 0.5 nm is still effective for further improvement in device performance.     

SrO capping effect for La2O3/Ce-silicate gate dielectrics

The chemical bonding states and electrical characteristics of SrO capped La₂O₃/CeO_x gate dielectric have been examined. Angle-resolved X-ray photoelectron spectroscopy measurement has revealed that Sr atoms diffuse into silicate layer to form SrLa-silicate after annealing. Owing to the incorporation of Sr atoms into silicate layer, a transistor operation with an equivalent oxide thickness (EOT) below 0.5 nm has been demonstrated. A strongly degraded effective electron mobility of 78 cm²/V s at 1 MV/cm has been obtained, which fit well with the general trend in small EOT range below 1 nm. Although process optimization is needed to improve the performance of transistors, Sr capping technique can be useful for EOT scaling.     

Process damage-free damascene metal gate technology for gentle integration of epitaxially grown high-k

This paper presents the first successful attempt to integrate crystalline high-k gate dielectrics into a virtually damage-free damascene metal gate process. Process details as well as initial electrical characterization results on fully functional gate Gd₂O₃ dielectric MOSFETs with equivalent oxide thickness (EOT) down to 1.9 nm are discussed and compared with devices with rare-earth gate dielectrics fabricated previously in a conventional CMOS process.     

Examination and evaluation of La2O3 as gate dielectric for sub-100 nm CMOS and DRAM technology

High-k gate dielectric La₂O₃ thin films have been deposited on Si(1 0 0) substrates by molecular beam epitaxy (MBE). Al/La₂O₃/Si metal-oxide–semiconductor capacitor structures were fabricated and measured. A leakage current of 3 × 10⁻⁹ A/cm² and dielectric constant between 20 and 25 has been measured for samples having an equivalent oxide thickness (EOT) 2.2 nm. The estimated interface state density D_it is around 1 × 10¹¹ eV⁻¹ cm⁻². EOT and flat-band voltage were calculated using the NCSU CVC program. The chemical composition of the La₂O₃ films was measured using X-ray photoelectron spectrometry and Rutherford backscattering. Current density vs. voltage curves show that the La₂O₃ films have a leakage current several orders of magnitude lower than SiO₂ at the same EOT. Thin La₂O₃ layers survive anneals of up to 900 °C for 30 s with no degradation in electrical properties.     

Thermal-stability improvement of LaON thin film formed using nitrogen radicals

This work reports the influence of nitridation on structural and electrical properties of La₂O₃ gate dielectric films. The issue of La₂O₃ is EOT increase after high temperature post metarization annealing (PMA). To overcome this problem, we incorporated nitrogen in La₂O₃. The EOT increase on the TaN/LaON and W/LaON structure is reduced compared with that on the W/La₂O₃ structure. This is due to nitrogen in LaON and SiN_x-rich interfacial layer which seems to remain after high temperature annealing. W/LaON nMOSFET is also successfully fabricated. Peak electron mobility of 96.2 cm²/V s was obtained.     

Composition and electrical characteristics of Al2O3-HfO2-HfTiO nanolaminates on Si

A dielectric constant of 27 was demonstrated in the as deposited state of a 5 nm thick, seven layer nanolaminate stack comprising Al₂O₃, HfO₂ and HfTiO. It reduces to an effective dielectric constant (k_eff) of ∼14 due to a ∼0.8 nm interfacial layer. This results in a quantum mechanical effective oxide thickness (EOT) of ∼1.15 nm. After annealing at 950 °C in an oxygen atmosphere k_eff reduces to ∼10 and EOT increases to 1.91 nm. A small leakage current density of about 8 × 10⁻⁷ and 1 × 10⁻⁴ A/cm², respectively at electric field 2 and 5 MV/cm and a breakdown electric field of about 11.5 MV/cm was achieved after annealing at 950 °C.     

Experimental study for high effective mobility with directly deposited HfO2/La2O3 MOSFET

We experimentally examine the effective mobility in nMOSFETs with La₂O₃ gate dielectrics without SiO_x-based interfacial layer. The reduced mobility is mainly caused by fixed charges in High-k gate dielectrics and the contribution of the interface state density is approximately 30% at N_s = 5 × 10¹¹ cm^?2 in the low 10¹¹ cm^?2 eV^?1 order. It is considered that one of the effective methods for improving mobility is to utilize La-silicate layer formed by high temperature annealing. However, there essentially exists trade-off relationship between high temperature annealing and small EOT.     

Dual layer SrTiO3/HfO2 gate dielectric for aggressively scaled band-edge nMOS devices

We have fabricated TiN/Poly-Si gated MOS devices with SrTiO₃/HfO₂ dual layer gate dielectric. These gate dielectrics show EOT (Equivalent Oxide Thickness) scaling of less than 0.7 nm as well as large V_fb shift in the nMOS direction after conventional gate first process. A sweet spot is observed for 0.5 nm SrTiO₃ where a band-edge effective work-function is obtained with improved EOT, reduced gate leakage and minimal hysteresis increase. But Sr diffuse into the interfacial layer leads to interface degradation. It is shown that proper PDA (post-deposition anneal) can improve interface quality while maintaining thinner EOT.     

Effect of thin Si insertion at metal gate/high-k interface on electrical characteristics of MOS device with La2O3

The effect of a thin Si layer insertion at W/La₂O₃ interface on the electrical characteristics of MOS capacitors and transistors is investigated. A suppression in the EOT increase can be obtained with Si insertion, indicating the inhibition of diffusion of oxygen atoms into La₂O₃ layer by forming an amorphous La-silicate layer at the W/La₂O₃ interface. In addition, positive shifts in V_fb and V_th caused by Si insertion implies the formation of amorphous La-silicate layer at the top of La₂O₃ dielectrics reduces the positive fixed charges induced by the metal electrode. Consequently, a large improvement in mobility has been confirmed for both at peak value and at high E_eff of 1 MV/cm with Si inserted nFETs. Although a degradation trend on EOT scaling has been observed, the insertion of thin Si layer is effective in pushing the scaling limit.     

La2O3 gate dielectrics for AlGaN/GaN HEMT

The annealing temperature dependent electrical characteristics of La₂O₃ gate dielectrics for W gated AlGaN/GaN high electron mobility transistors (HEMTs) have been characterized. The threshold voltage (V_th) has been found to shift to positive direction with higher temperature annealing, exceeding those of Schottky HEMTs, presumably attributed to the presence of negative fixed charges at the interface between La₂O₃ and AlGaN layers. At a high temperature annealing over 500 °C, a high dielectric constant (k-value) of 27 has been achieved with poly-crystallization of the La₂O₃ film, which is useful to limit the reduction in gate capacitance. A high k-value for La₂O₃ gate dielectrics and the presence of negative charges at the interface are attractive for AlGaN/GaN HEMTs with low gate leakage and normally-off operation.     

Fabrication and characterization of Zr-rich Zr-aluminate films for high-κ gate dielectric applications

Two kinds of Zr-rich Zr-aluminate films for high-κ gate dielectric applications with the nominal composition of (ZrO₂)_0.8(Al₂O₃)_0.2 and (ZrO₂)_0.9(Al₂O₃)_0.1, were deposited on n-type silicon wafer by pulsed laser deposition (PLD) technique at different deposition conditions. X-ray diffraction (XRD) reveals that the (ZrO₂)_0.8(Al₂O₃)_0.2 film could remain amorphous after being rapid thermal annealed (RTA) at the temperature above 800 °C, while the other one displays some crystalline peaks at 700 °C. The energy gap calculated from optical transmittance spectrum of (ZrO₂)_0.8(Al₂O₃)_0.2 film on quartz is about 6.0 eV. Sputtering depth profile of X-ray photoelectron spectroscopy and Auger electron spectroscopy indicate that a Zr-Si-O interfacial layer was formed at the near surface of the silicon substrate. The dielectric constant of the (ZrO₂)_0.8(Al₂ O₃)_0.2 film has been determined to be 22.1 by measuring a Pt/(ZrO₂)_0.8(Al₂ O₃)_0.2/Pt MIM structure. An EOT of 1.76 nm with a leakage current density of 51.5 mA/cm² at 1 V gate voltage for the film deposited in N₂ were obtained. Two different pre-treatments of Si substrates prior to depositions were also carried out and compared. The results indicate that a surface-nitrided Si substrate can lead to a lower leakage current density. The amorphous Zr-rich Zr-aluminate films fabricated by PLD have promising structure and dielectric properties required for a candidate material for high-κ gate dielectric applications.     

Study of gate dielectric permittivity variation with different equivalent oxide thickness on channel engineered deep sub-micrometer n-MOSFET device for mixed signal applications

The impact of high permittivity gate dielectrics with different equivalent oxide thickness (EOT) for conventional, low and high tilt angle halo implants on the performance of 100 nm n-MOSFETs device is studied using device simulator Synopsys ISE-TCAD. In this paper, we systematically increase the value of gate dielectric (3.9-50) and investigate its effects on conventional, low angle of tilt (10^o) and high angle of tilt (50^o) halo implants for different device parameters of 100 nm n-MOSFETs using two different EOT viz. 1.5 nm and 2.0 nm. The impact of gate dielectric permittivity along with the different angles of halo implants on short channel performance contributing to the DIBL, the subthreshold swing, I_ON/I_OFF ratio, and the threshold voltage V_T are studied for two different EOT thicknesses. The device has been investigated for digital performance parameters like the variation of substrate-body voltage on DIBL, I_OFF, I_ON and the threshold voltage V_T for sub 100 nm technology generation. It has also been investigated for analog performance like trans-conductance generation factor (gm/I_D) and overall gain (gmR₀).     

Effect of RuO2 electrode on laser-MBE prepared HfO2 gate dielectrics

In this paper, we report our recent study of the effect of RuO₂ as an alternative top electrode for pMOS devices to overcome the serious problems of polysilicon (poly-Si) gate depletion, high gate resistance and dopant penetration in the trend of down to 50 nm devices and beyond. The conductive oxide RuO₂, prepared by RF sputtering, was investigated as the gate electrode on the Laser MBE (LMBE) fabricated HfO₂ for pMOS devices. Structural, dielectric and electric properties were investigated. RuO₂/HfO₂/n-Si capacitors showed negligible flatband voltage shift (<10 mV), very strong breakdown strength (>10 MV cm⁻¹). Compared to the SiO₂ dielectric with the same EOT value, RuO₂/HfO₂/n-Si capacitors exhibited at least 4 orders of leakage current density reduction. The work function value of the RuO₂ top electrode was calculated to be about 5.0 eV by two methods, and the effective fixed oxide charge density was determined to be 3.3 × 10¹² cm⁻². All the results above indicate that RuO₂ is a promising alternative gate electrode for LMBE grown HfO₂ gate dielectrics.     

Growth of lanthanum oxide films for application as a gate dielectric in CMOS technology

We have investigated properties of insulating lanthanum oxide (La₂O₃) films in connection with the replacement of silicon oxide (SiO₂) gate dielectrics in new generation of CMOS devices. The La₂O₃ layers were grown using metal organic chemical vapour deposition (MOCVD) at 500 °C. X-ray diffraction analysis revealed polycrystalline character of the films grown above 500 °C. The X-ray photoemission spectroscopy detected lanthanum carbonate as a principal impurity in the films and lanthanum silicate at the interface with silicon. Density of oxide charge, interface trap density, leakage currents and dielectric constant ( κ) were extracted from the C-V and I-V measurements. Electrical properties, in particular dielectric constant of the MOCVD grown La₂O₃ are discussed with regard to the film preparation conditions. The as grown film had κ11. Electrical measurements indicate possible presence of oxygen vacancies in oxide layer. The O₂-annealed La₂O₃ film had κ17.     

N and P metal oxide semiconductor field effect transistor characteristics of hafnium-doped SiO2 gate dielectrics

This work presents the interfacial properties of hafnium-doped SiO₂ films via N and P metal oxide semiconductor (MOS) materials, MOS-capacitor, and N and P metal oxide semiconductor field effect transistor (MOSFET) characterization. The results indicate that HfSi_xO_y films (a) have excellent transistor characteristics; (b) remain amorphous through high-temperature processing; (c) are compatible with N+ and P+ polysilicon electrodes; (d) have lower gate leakage than SiO₂ of the same equivalent oxide thickness (EOT); and (e) have a dielectric constant of ∼8. Therefore, the hafnium-doped SiO₂ films are at-tractive as a dielectric material and offer a technologically relevant gate-stack node for insertion, prior to deployment of high-K dielectrics.     

Monte carlo study of mobility in Si devices with -based oxides

HfO₂-based high-κ dielectrics are among the most likely candidates to replace SiO₂ and the currently favoured oxinitride in the next generation of MOSFETs. High-κ materials allow the use of a thicker gate dielectric, maintaining the gate capacitance with reduced gate leakage. However, they lead to a fundamental mobility degradation due to the coupling of carriers to surface soft (low-energy) optical phonons. Comparing the vertical field dependence of the mobility for HfO₂ and SiO₂, the severe degradation in mobility in the presence of high-κ becomes evident. The introduction of a SiO₂ interfacial layer between the channel and the HfO₂ mitigates this degradation, by increasing the effective distance between the carriers and the SO phonons, thus decreasing the interaction strength, this does though lead to an increase in the equivalent oxide thickness (EOT) of the gate dielectric. The material of choice for the first commercial introduction of high-κ gate stacks is Hafnium Silicate (Si_xHf_1-xO₂). This alloy stands up better to the processing challenges and as a result suffers less from dielectric fluctuations. We show that as the fraction of Hf increases within the alloy, the inversion layer mobility is shown to decrease due to the corresponding decrease in the energy of the surface optical phonons and increase in the dielectric constant of the oxide.     

A low-frequency noise model for advanced gate-stack MOSFETs

A new unified noise model is presented that accurately predicts the low-frequency noise spectrum exhibited by MOSFETs with high dielectric constant (high-k), multi-stack gate dielectrics. The proposed multi-stack unified noise (MSUN) model is based on number and correlated mobility fluctuations theory developed for native oxide MOSFETs, and offers scalability with respect to the high-k/interfacial layer thicknesses. In addition, it incorporates the various electronic properties of high-k/interfacial layer materials such as energy barrier heights between different gate layers, and dielectric trap density with respect to band energy and position in the dielectric. For verification of the new model, the low-frequency noise, DC and conventional split C-V measurements were performed in the 78-350 K temperature range on TaSiN/HfO₂ n-channel MOSFETs. The interfacial layer in these devices was either thermal SiO₂ by Stress Relieved Pre-Oxide (SRPO) pretreatment or chemical SiO₂ resulting from standard RCA (Radio Corporation of America) clean process. Using the experimental noise data, the channel carrier number fluctuations mechanism was at first established to be the underlying mechanism responsible for the noise observed at all temperatures considered. Secondly, the normalized noise exhibited a weak dependence on temperature implying that the soft optical phonons, although known to result in mobility degradation, have no effect on the noise characteristics in these high-k gate stack MOSFETs. Finally, the new model was shown to be in excellent agreement with the measured noise in 1-100 Hz frequency range at temperatures of 78-350 K for both gate stacks.     

Damascene TiN-Gd2O3-gate stacks: Gentle fabrication and electrical properties

In this work, we present MOS capacitors and field effect transistors with a crystalline gadolinium oxide (Gd₂O₃) gate dielectric and metal gate electrode (titanium nitride) fabricated in a gentle damascene gate last process. Details of the gate last process and initial results on MOS devices with equivalent oxide thicknesses (EOT) of 3.0 nm and 1.5 nm, respectively, are shown.     

Interfacial transition regions at germanium/Hf oxide based dielectric interfaces: Qualitative differences between non-crystalline Hf Si oxynitride and nanocrystalline HfO2 gate stacks

The contribution from a relatively low-K SiON (K ∼ 6) interfacial transition region (ITR) between Si and transition metal high-K gate dielectrics such as nanocrystalline HfO₂ (K ∼ 20), and non-crystalline Hf Si oxynitride (K ∼ 10-12) places a significant limitation on equivalent oxide thickness (EOT) scaling. This limitation is equally significant for metal-oxide-semiconductor capacitors and field effect transistors, MOSCAPs and MOSFETs, respectively, fabricated on Ge substrates. This article uses a novel remote plasma processing approach to remove native Ge ITRs and bond transition metal gate dielectrics directly onto crystalline Ge substrates. Proceeding in this way we identify (i) the source of significant electron trapping at interfaces between Ge and Ge native oxide, nitride and oxynitride ITRs, and (ii) a methodology for eliminating native oxide, or nitride IRTs on Ge, and achieving direct contact between nanocrystalline HfO₂ and non-crystalline high Si₃N₄ content Hf Si oxynitride alloys, and crystalline Ge substrates. We then combine spectroscopic studies, theory and modeling with electrical measurements to demonstrate the relative performance of qualitatively different nanocrystalline and non-crystalline gate dielectrics for MOS Ge test devices.     

Low operational voltage and high performance organic field effect memory transistor with solution processed graphene oxide charge storage media

Low voltage organic field effect memory transistors are demonstrated by adapting a hybrid gate dielectric and a solution processed graphene oxide charge trap layer. The hybrid gate dielectric is composed of aluminum oxide (AlO_x) and [8-(11-phenoxy-undecyloxy)-octyl]phosphonic acid (PhO-19-PA) plays an important role of both preventing leakage current from gate electrode and providing an appropriate surface energy to allow for uniform spin-casting of graphene oxide (GO). The hybrid gate dielectric has a breakdown voltage greater than 6 V and capacitance of 0.47 μF/cm². Graphene oxide charge trap layer is spin-cast on top of the hybrid dielectric and has a resulting thickness of approximately 9 nm. The final device structure is Au/Pentacene/PMMA/GO/PhO-19-PA/AlO_x/Al. The memory transistors clearly showed a large hysteresis with a memory window of around 2 V under an applied gate bias from 4 V to −5 V. The stored charge within the graphene oxide charge trap layer was measured to be 2.9 × 10¹² cm⁻². The low voltage memory transistor operated well under constant applied gate voltage and time with varying programming times (pulse duration) and voltage pulses (pulse amplitude). In addition, the drain current (I_ds) after programming and erasing remained in their pristine state after 10⁴ s and are expected to be retained for more than one year.