Increasing the bonding strength of chips on flex substrates using thermosonic flip-chip bonding process with nonconductive paste

Thermosonic flip-chip bonding process with a nonconductive paste (NCP) was employed to improve the processability and bonding strength of the flip-chip onto flex substrates (FCOF). A non-conductive paste was deposited on the surface of the copper electrodes over the flex substrate, and a chip with eight gold bumps bonded onto the copper electrodes by the thermosonic flip-chip bonding process.For the chips and flex substrates assembly, ultrasonic power is important in the removal of some of the non-conductive paste on the surface of copper electrodes during thermosonic bonding. Accordingly, gold stud bumps in this study were directly bonded onto copper electrodes to form successful electrical paths between chips and the flex substrate. A particular ultrasonic power resulted in some metallurgical bonding between the gold bumps and the copper electrodes, increasing the bonding strength. The ultrasonic power was not only to remove the NCP from the copper electrodes, but also formed metallurgical bonds during the thermosonic flip-chip bonding process with NCP.In this study, the parameters of the bonding of chips onto flex substrates using thermosonic flip-chip bonding process with NCP were a bonding force of 4.9 N, a curing time of 40 s, a curing temperature of 140 °C and an ultrasonic power of 14.46 W. The processability and bonding strength of flip-chips on flex substrates using thermosonic bonding process with NCP was verified in this study. This process has great potential to be applied to the packaging of consumed electronic products.     

Gold Stud Bumps Flip-Chip Bonded onto Copper Electrodes with Titanium and Silver Layers

The purpose of this study was to develop the thermosonic flip-chip bonding process for gold stud bumps bonded onto copper electrodes on an alumina substrate. Copper electrodes were deposited with silver as the bonding layer and with titanium as the diffusion barrier layer. Deposition of these layers on copper electrodes improves the bonding quality between the gold stud bumps and copper electrodes. With appropriate bonding parameters, 100% bondability was achieved. Bonding strength between the gold stud bumps and copper electrodes was much higher than the value converted from the standards of the Joint Electron Device Engineering Council (JEDEC). The effects of process parameters, including bonding force, ultrasonic power, and bonding time, on bonding strength were also investigated. Experimental results indicate that bonding strength increased as bonding force and ultrasonic power increased and did not deteriorate after prolonged storage at elevated temperatures. Thus, the reliability of the high-temperature storage (HTS) test for gold stud bumps flip-chip bonded onto a silver bonding layer and titanium diffusion barrier layer is not a concern. Deposition of these two layers on copper electrodes is an effective and direct method for thermosonic flip-chip bonding of gold stud bumps to a substrate, and ensures excellent bond quality. Applications such as flip-chip bonding of chips with low pin counts or light-emitting diode (LED) packaging are appropriate.     

HTS and PCT Reliability of Chips and Flex Substrates Assembled Using a Thermosonic Flip-Chip Bonding Process

This study assesses the high-temperature storage (HTS) test and the pressure-cooker test (PCT) reliability of an assembly of chips and flexible substrates. After the chips were bonded onto the flexible substrates, specimens were utilized to assess the HTS test and PCT reliability. After the PCT and HTS tests, the die-shear test was applied to examine changes in die-shear forces. The microstructure of the test specimens was analyzed to evaluate reliability and to identify possible failure mechanisms. When the duration of the HTS test was increased, the percentage of gold bumps that peeled off from the surface of the copper pads on the chip side increased, and a crack was present at the bonding interface between the gold bumps and chip bond pads. This crack was due to thermal stress generated during the HTS test, and degraded the die-shear force of the assembly of chips and flexible substrates. After the PCT, the crack was present at the interface between deposited layers of copper electrodes after the specimens were subjected to the PCT for various durations. Moisture penetrated into the deposited layers of the copper electrodes, deposited layers lost their adhesion, and the crack progressed from the corner into the central bond area as the test duration increased. To improve the PCT reliability of assemblies of chips and flexible substrates using the thermosonic flip-chip bonding process, one must prevent moisture from penetrating into deposited layers of copper electrodes and prevent crack formation at the interface between nickel and copper layers. Underfill would be an effective approach to prevent moisture from penetrating into deposited layers during the PCT, thereby improving the reliability of the samples during the PCT.     

Enhancement of the Bondability and Die-Shear Force of Chip–Flex Substrate Assemblies by Depositing a Nickel Layer on the Flex Substrate

A nickel layer and a silver bonding layer have been deposited on copper electrodes over flex substrates to improve the bondability and die-shear force performance of chip?Cflex substrate assemblies when using the thermosonic flip-chip bonding process. For bonding temperature of 200°C, the maximum die-shear force was achieved by combining parameter values of 20.66?W ultrasonic power, 625?gf bonding force, and 0.5?s bonding time. The improved bondability and die-shear force could be attributed to better transfer of ultrasonic power across the bonding interface during thermosonic flip-chip bonding, owing to the high rigidity of the copper electrodes provided by the nickel layer. Experimental results also indicated that high bonding load is necessary at elevated ultrasonic power range to provide firm contact between the bumps and electrodes to enable smooth ultrasonic power transfer across the bonding interface. Moreover, prolonged bonding time caused cracks between the bumps and flex substrate. Close examination of the fracture morphologies after die-shear testing and after ultrasonic separation provided insight into the die-shear force performance as influenced by the process parameters and by the deposition of the nickel layer on the copper electrodes over the flex substrate.     

Increasing bondability and ball-shear force of gold balls thermosonic bonding to flex substrates by depositing a nickel layer

To improve the bondability and ball-shear force of gold balls that are thermosonically bonded to copper electrodes over flex substrates, a nickel layer was deposited on the surface of the copper electrodes to increase their rigidity. A silver layer was then deposited on the nickel layer to prevent oxidation of the copper electrodes during the thermosonic bonding process. This nickel layer was expected to enhance the rigidity of copper electrodes over the flex substrates, increasing the thermosonic bonding efficiency of gold balls to copper electrodes over the flex substrates.Deposition the nickel layer on the copper electrodes improved the elastic modulus of the flex substrates, indicating that the nickel layer is effective in enhancing the rigidity of copper electrodes over the flex substrates. The bondability and ball-shear force of gold balls that are thermosonically bonded to copper electrodes increases with the thickness of the nickel layer given fixed bonding parameters. One hundred percent bondability and high ball-shear force can be achieved when gold balls are thermosonically bonded to copper electrodes with the deposition of a 0.5 μm-thick nickel layer. Herein, the ball-shear force was higher than that specified in JEDEC standards. Furthermore, gold balls that were thermosonically bonded to copper electrodes with a nickel layer had a large bonded area with an extensive scrape, while gold balls that were thermosonically bonded to copper electrodes without a nickel layer had a blank surface morphology. This experimental result was similar to that of tests of the elastic modulus of flex substrates, similarity can be used to explain that the effectiveness of the nickel layer in increasing the rigidity of copper electrodes, increasing the bonding efficiency at the bonding interface between gold balls and copper electrodes during thermosonic bonding process. After ball-shear test, a layer that was stuck on the ball bond was observed at the location of fracture of the ball bonds for gold balls they were thermosonically boned on copper electrodes with 0.5 μm-thick nickel layer. This observation implies that the ball-shear force of the gold balls that were bonded on the copper electrodes exceeded even the adhesive force of the layers that were deposited on the copper electrodes.The deposition of a 0.5 μm-thick nickel layer on copper electrodes over flex substrates improved the rigidity of the copper electrodes; the ultrasonic power could be propagated to the bonding interface between the gold balls and the copper electrodes, increasing the bondability and ball-shear force.     

Thermosonic bonding of gold wire onto silver bonding layer on the bond pads of chips with copper interconnects

A copper pad oxidizes easily at elevated temperatures during thermosonic wire bonding for chips with copper interconnects. The bondability and bonding strength of a gold wire onto a bare copper pad are seriously degraded by the formation of a copper oxide film. A new bonding approach is proposed to overcome this intrinsic drawback of the copper pad. A silver layer is deposited as a bonding layer on the surface of copper pads. Both the ball-shear force and the wire-pull force of a gold wire bonded onto copper pads with silver bonding layers far exceed the minimum values stated in the JEDEC standard and MIL specifications. The silver bonding layer improves bonding between the gold ball and copper pads. The reliability of gold ball bonds on a bond pad is verified in a high-temperature storage (HTS) test. The bonding strength increases with the storage time and far exceeds that required by the relevant industrial codes. The superior bondability and high strength after the HTS test were interpreted with reference to the results of electron probe x-ray microanalyzer (EPMA) analysis. This use of a silver bonding layer may make the fabrication of copper chips simpler than by other protective schemes.     

Increasing bondability and bonding strength of gold stud bumps onto copper pads with a deposited titanium barrier layer

A flip-chip assembly is an attractive scheme for use in high performance and miniaturized microelectronics packaging. Wafer bumping is essential before chips can be flip-bonded to a substrate. Wafer bumping can be used for mechanical-single point stud bump bonding (SBB), and is based on conventional thermosonic wire bonding. This work proposes depositing a titanium barrier layer between the copper film and the silver bonding layer to achieve perfect bondability and sufficiently strong thermosonic bonding between a stud bump and the copper pad.A titanium layer was deposited on the copper pads to prevent copper atoms from out-diffusing during thermosonic stud bump bonding. A silver film was then deposited on the surface of the titanium film as a bonding layer to increase the bondability and bonding strength for stud bumps onto copper pads. The integration of the silver bonding layer with a diffusion barrier layer of titanium on the copper pads yielded 100% bondability between the stud bump and pads. The strength of bonding between the gold bumps on the copper pads significantly exceeds the minimum average values in JEDEC specifications. The diffusion barrier layer of titanium effectively prevents copper atoms from out-diffusing to the silver bonding layer surface during thermosonic bonding, which fact can be interpreted with reference to the experimental results of energy dispersive spectrometry (EDS) and analyses of Auger depth profiles. This diffusion barrier layer of titanium efficiently provides perfect bondability and sufficiently strong bonding between a stud bump and copper pads with a silver bonding layer.     

RFID芯片超声倒装封装技术研究

超声倒装是近年来芯片封装领域中快速发展的一种倒装技术,具有连接强度高、接触电阻低、可靠性高、低温下短时完成和成本低的优势,特别适合较少凸点的RFID芯片封装。在镀Ni/Au铜基板上进行了RFID芯片超声倒装焊接实验,金凸点与镀Ni/Au铜基板之间实现了冶金结合,获得了良好的力学与电气性能,满足射频要求。     

Thermosonic bonding of gold wire onto a copper pad with titanium thin-film deposition

A novel thermosonic (TS) bonding process for gold wire bonded onto chips with copper interconnects was successfully developed by depositing a thin, titanium passivation layer on a copper pad. The copper pad oxidizes easily at elevated temperature during TS wire bonding. The bondability and bonding strength of the Au ball onto copper pads are significantly deteriorated if a copper-oxide film exists. To overcome this intrinsic drawback of the copper pad, a titanium thin film was deposited onto the copper pad to improve the bondability and bonding strength. The thickness of the titanium passivation layer is crucial to bondability and bonding strength. An appropriate, titanium film thickness of 3.7 nm is proposed in this work. One hundred percent bondability and high bonding strength was achieved. A thicker titanium film results in poor bond-ability and lower bonding strength, because the thicker titanium film cannot be removed by an appropriate range of ultrasonic power during TS bonding. The protective mechanism of the titanium passivation layer was interpreted by the results of field-emission Auger electron spectroscopy (FEAES) and electron spectroscopy for chemical analysis (ESCA). Titanium dioxide (TiO₂), formed during the die-saw and die-mount processes, plays an important role in preventing the copper pad from oxidizing. Reliability of the high-temperature storage (HTS) test for a gold ball bonded on the copper pad with a 3.7-nm titanium passivation layer was verified. The bonding strength did not degrade after prolonged storage at elevated temperature. This novel process could be applied to chips with copper interconnect packaging in the TS wire-bonding process.     

Development of a thermosonic wire-bonding process for gold wire bonding to copper pads using argon shielding

To improve the bondability and ensure the reliability of Au/Cu ball bonds of the thermosonic (TS) wire-bonding process, an argon-shielding atmosphere was applied to prevent the copper pad from oxidizing. With argon shielding in the TS wire-bonding process, 100% gold wire attached on a copper pad can be achieved at the bonding temperature of 180°C and above. The ball-shear and wire-pull forces far exceed the minimum requirements specified in the related industrial codes. In a suitable range of bonding parameters, increasing bonding parameters resulted in greater bonding strength. However, if bonding parameters exceed the suitable range, the bonding strength is deteriorated. The reliability of the high-temperature storage (HTS) test for Au/Cu ball bonds was verified in this study. The bonding strength of Au/Cu ball bonds increases slightly with prolonged storage duration because of diffusion between the gold ball and copper pad during the HTS test. As a whole, argon shielding is a successful way to ensure the Au/Cu ball bond in the TS wire-bonding process applied for packaging of chips with copper interconnects.     

Thermosonic flip-chip bonding for SAW filter

A flip-chip bonding (FCB) method suitable for the surface acoustic wave (SAW) filter was developed. In this method, the gold-ball bumps formed on the chip are directly bonded onto the ceramic substrate by thermosonic bonding. After FCB, they are sealed with a cap without using underfill resin. To obtain high bond strength, characteristic properties of the substrate electrode and the ball bump, were optimized. Furthermore, bondability has been improved by adopting a ramp-up loading profile. The reliability test was carried out with 6-pin SAW chips, and we confirmed the sufficient reliability of bonds.     

热超声倒装焊在制作大功率GaN基LED中的应用

设计了适合于倒装的大功率GaN基LED芯片结构,在倒装基板硅片上制作了金凸点,采用热超声倒装焊接(FCB)技术将芯片倒装在基板上.测试结果表明获得的大面积金凸点连接的剪切力最高达53.93 g/bump,焊接后的GaN基绿光LED在350 mA工作电流下正向电压为3.0 V.将热超声倒装焊接技术用于制作大功率GaN基LED器件,能起到良好的机械互连和电气互连.     

Effect of Gold Stud Bump Topology on Reliability of Flip Chip on Flex Interconnects

The flip chip technique using conductive adhesives have emerged as a good alternative to solder flip chip methods. Different approaches of the interconnection mechanism using conductive adhesives have been developed. In this paper, test chips with gold stud bumps are flip-chipped with conductive adhesives onto a flexible substrate. An experimental study to characterize the bonding process parameters is reported. Initial results from the environmental studies show that thermal shock test causes negligible failure. On the other hand, high humidity test causes considerable failure in flip chip on flex assemblies. Improvements in the reliability of the assembly are achieved by modifying the shape of the gold stud bumps.     

功率型LED芯片的热超声倒装技术

结合功率型GaN基蓝光LED芯片的电极分布,在硅载体上电镀制作了金凸点,然后通过热超声倒装焊接技术将LED芯片焊接到载体硅片上.结果表明,在合适的热超声参数范围内,焊接后的功率型LED光电特性和出光一致性较好,证明了热超声倒装焊接技术是一种可靠有效的功率型光电子器件互连技术.     

Laser-assisted bumping for flip chip assembly

A novel laser-assisted chip bumping technique is presented in which bumps are fabricated on a carrier and subsequently transferred onto silicon chips by a laser-driven release process. Copper bumps with gold bonding layers and intermediate nickel barriers are fabricated on quartz wafers with pre-deposited polyimide layers, using UV lithography and electroplating. The bumps are thermosonically bonded to their respective chips and then released from the carrier by laser machining of the polyimide layer, using light incident through the carrier. Bumps of 60 to 85 μm diameter and 50 μm height at a pitch of 127 μm have been fabricated in peripheral arrays. Parallel bonding and subsequent transfer of arrays of 28 bumps onto test chips have been successfully demonstrated. Individual bump shear tests have been performed on a sample of 13 test chips, showing an average bond strength of 26 gf per bump     

Flip chip interconnect systems using copper wire stud bump and leadfree solder

This research focuses on flip chip interconnect systems consisting of wire stud bumps and solder alloy interconnects. Conventional gold (Au) wire stud bumps and new copper (Cu) wire stud bumps were formed on the chip by wire stud bumping. Cu wire studs were bumped by controlling the ramp rate of ultrasonic power to eliminate the occurrence of under-pad chip cracks that tend to occur with high strength bonding wire. Lead free 96Sn3.5Ag0.5Cu (SnAgCu) alloy was used to interconnect the wire studs and printed circuit board. A comparison was made with conventional eutectic 63Sn37Pb (SnPb) alloy and 60In40Pb (InPb) alloy. Test vehicles were assembled with two different direct chip attachment (DCA) processes. When the basic reflow assembly using a conventional pick and place machine and convection reflow was used, 30% of the lead free test vehicles exhibited process defects. Other lead free test vehicles failed quickly in thermal shock testing. Applying the basic reflow assembly process is detrimental for the SnAgCu test vehicles. On the other hand, when compression bonding assembly was performed using a high accuracy flip chip bonder, the lead free test vehicles exhibited no process defects and the thermal shock reliability improved. Cu stud-SnAgCu test vehicles (Cu-SnAgCu) in particular showed longer mean time to failure, 2269 cycles for the B stage process and 3237 cycles for high temperature bonding. The C-SAM and cross section analysis of the Cu stud bump assemblies indicated less delamination in thermal shock testing and significantly less Cu diffusion into the solder compared to Au stud bumped test vehicles. The Cu stud-SnAgCu systems form stable interconnects when assembled using a compression bonding process. Moreover, Cu wire stud bumping offers an acceptable solution for lead free assembly     

Three-dimensional flip-chip on flex packaging for power electronicsapplications

We have extended the concept of flip-chip technology, which is widely used in IC packaging, to the packaging of three-dimensional (3-D) integrated power electronics modules (IPEMs). We call this new approach flip-chip on flex IPEM (FCOF-IPEM), because the power devices are flip-chip bonded to a flexible substrate with control circuits. We have developed a novel triple-stacked solder bump metallurgy for improved and reliable device interconnections. In this multilayer structure, we have carefully selected packaging materials that distribute the thermo-mechanical stresses caused by mismatching coefficients of thermal expansion (CTEs) among silicon chips and substrates. We have demonstrated the feasibility of this packaging approach by constructing modules with two insulated gate bipolar transistors (IGBTs), two diodes, and a simple gate driver circuit. Fabricated FCOF-IPEMs have been successfully tested at power levels up to 10 kW. This paper presents the materials and reliability issues in the package design along with electrical, mechanical, and thermal test results for a packaged IPEM     

Bondability Study of Chip-on-Film (COF) Inner Lead Bonding (ILB) Using Conventional Gang Bonder

Inner lead bonding (ILB) is used to thermomechanically join the Cu inner leads on a flexible film tape and Au bumps on a driver IC chip to form electrical paths. With the newly developed film carrier assembly technology, called chip on film (COF), the bumps are prepared separately on a film tape substrate and bonded on the finger lead ends beforehand; therefore, the assembly of IC chips can be made much simpler and cheaper. In this paper, three kinds of COF samples, namely forming, wrinkle, and flat samples, were prepared using conventional gang bonder. The peeling test was used to examine the bondability of ILB in terms of the adhesion strength between the inner leads and the bumps. According to the peeling test results, flat samples have competent strength, less variation, and better appearance than when using flip-chip bonder.     

Effects of underfill materials on the reliability of low-K flip-chip packaging

The reliability of low-K flip-chip packaging has become a critical issue owing to the low strength and poor adhesion qualities of the low-K dielectric material when compared with that of SiO₂ or fluorinated silicate glass (FSG). The underfill must protect the solder bumps and the low-K chip from cracking and delamination. However, the material properties of underfill are contrary to those required for preventing solder bumps and low-K chip from cracking and delamination. This study describes the systematic methodologies for how to specify the adequate underfill materials for low-K flip-chip packaging. The structure of the test vehicle is seven copper layers with a low-K dielectric constant value of 2.7-2.9, produced by the chemical vapor deposition (CVD) process. Initially, the adhesion and the flow test of the underfill were evaluated, and then the low-K chip and the bumps stress were determined using the finite element method. The preliminary screened underfill candidates were acquired by means of the underfill adhesion and flow test, and balancing the low-K chip and the bumps stress simulation results. Next, the low-K chips were assembled with these preliminary screened underfills. All the flip-chip packaging specimens underwent the reliability test in order to evaluate the material properties of the underfill affecting the flip-chip packaging stress. In addition, the failed samples are subjected to failure analysis to verify the failure mechanism. The results of this study indicate that, of the underfill materials investigated, those with a glass transition temperature (T_g) and a Young’s modulus of approximately 70–80 °C and 8–10 GPa, respectively, are optimum for low-K flip-chip packaging with eutectic solder bumps.     

A Novel Three-Dimensional Packaging Method for Al-Metalized SiC Power Devices

A novel three-dimensional packaging method for Al-metalized SiC power devices has been developed by means of Au stud bumping technology and a subsequent vacuum reflow soldering process with Au-20Sn solder paste. Al-metalized electrodes of a SiC power chip can be robustly assembled to a direct bonded copper (DBC) substrate with this method. The bump shear strength of a Au stud bump on an Al electrode of a SiC chip increased with bonding temperature. The die shear strength of a SiC chip on the DBC substrate increased with the number of Au stud bumps which were preformed on the Al electrode. The bonded SiC-SBD chips on a DBC substrate were aged at 250 ${^circ}{rm C}$ in a vacuum furnace and the morphologies, die shear strength and electrical properties were investigated after a certain aging time. After 1000 h aging at 250 ${^circ}{rm C}$, the electrical resistance of the bonded SiC-SBD chips only increased about 0.4%, the residual die shear strength was much higher than that of the IEC749 (or JEITA) standard value, and little morphological change was observed by a micro-focus X-ray TV system. Very little diffusion between Au stud bumps and Au-20Sn solder was observed by scanning electron microscope (SEM) equipped with an energy dispersed X-ray analyzer (EDX). Intermetallic compounds (IMC) evolved at the interface of chip/solder and chip/Au stud bumps after 1000 h aging at 250 ${^circ}{rm C}$. With this method, power devices with Al bond pads can be three-dimensionally packaged.