Very low input impedance low power current mirror

In this paper a novel low input impedance current mirror/source is proposed. The principle of its operation compared to that of the simple current mirror is discussed. Also are given the comparative simulation results with HSPICE in TSMC 0.18 μm CMOS which verify the theoretical formulation and operation of the proposed structure. Simulation results show an input resistance for the proposed current mirror about 0.006 Ω. This is 4 × 10⁵ times lower than that of the simple one while both working with 1.5 V supply and 50 μA bias current. It consumes only 161 μW and exhibits an excellent current error value of Zero at 55 μA which remains below 0.6% up to 100 μA. Favorably its minimum output voltage is reduced to 0.2 V.     

A high speed low input impedance current pulse amplifier cell

A high speed CMOS current pulse amplifier cell with low input impedance, devoted to nuclear multichannel detectors where crosstalk is a serious problem, is presented. The symmetry of the circuit achieved with complementary transistors yields both an input and an output with low offset voltage, opening a large field of applications such as transimpedance amplifiers and therefore transimpedance operational amplifiers.     

Low supply voltage high-performance CMOS current mirror with low input and output voltage requirements

This paper presents a scheme for the efficient implementation of a low supply voltage continuous-time high-performance CMOS current mirror with low input and output voltage requirements. This circuit combines a shunt input feedback and a regulated cascode output stage to achieve low input resistance and very high output resistance. It can be used as a high-precision current mirror in analog and mixed signal circuits with a power supply close to a transistor's threshold voltage. The proposed current mirror has been simulated and a bandwidth of 40 MHz has been obtained. An experimental chip prototype has been sent for fabrication and has been experimentally verified, obtaining 0.15-V input-output voltage requirements, 100-/spl Omega/ input resistance, and more than 200-M/spl Omega/ (G/spl Omega/ ideally) output resistance with a 1.2-V supply in a standard CMOS technology.     

A CMOS operational amplifier with low impedance drive capability

A CMOS operational amplifier capable of delivering 160 mW of power to a 100 /spl Omega/ load while only dissipating 7 mW of quiescent power is described. The amplifier consists of three stages, the last of which is a transconductance output driver. The output stage is operated class B with less than 2 percent typical THD. A method of setting crossover by ratioing current mirror loads to parallel invertors is shown. Experimental results are presented showing various nominal operating characteristics.     

Modified current mirror with a `voltage-following? capability

A negative current mirror suitable for monolithic IC fabrication is described. It is unusual in that it is a `voltage-following? circuit in which the input-output offset voltage is small and only weakly dependent on operating conditions. A base-current compensation scheme enables the circuit to exhibit a current transfer ratio comparable with that of the `Wilson? current mirror.     

High input impedance current conveyor filters

Two new active RC canonic band pass filters are presented. The new configurations offer a very high input impedance and employ single grounded resistors for independent adjustments of ω₀, Q and gain.     

A novel ultra-high compliance, high output impedance low power very accurate high performance current mirror

In this paper a novel ultra-high compliance, low power, very accurate and high output impedance current mirror/source is proposed. Deliberately composed elements and a good combination (for a mutual auto control action) of negative and positive feedbacks in the proposed circuit made it unique in gathering ultra-high compliances, high output impedance and high accuracy ever demanded merits. The principle of operation of this unique structure is discussed, its most important formulas are derived and its outstanding performance is verified by HSPICE simulation in TSMC 0.18 μm CMOS, BSIM3 and Level49 technology. Simulation results with 1 V power supply and 8 μA input current show an input and output minimum voltages of 0.058 and 0.055 V, respectively, which interestingly provide the highest yet reported compliances for current mirrors implemented by regular CMOS technology. Besides an input resistance of 13.3 Ω, an extremely high output resistance of 34.3 GΩ and −3 dB cutoff frequency of 210 MHz are achieved for the proposed circuit while it consumes only 42.5 μW and its current transfer error (at bias point) is the excellent value of 0.02%.     

Body controlled threshold voltage shifting variable gain current mirror

A programmable high-speed source-series-terminated driver with signal boost capability is presented. The driver uses only one main input data tap and is divided into main units and auxiliary units. A passive high pass filter is utilized to detect data transitions and control the inputs of the auxiliary units to enable a programmable amplitude boost for the output signal. The corner frequency of the high pass filter is adjusted depending on the data rate. Further, the amount of the high frequency signal boost can be adjusted depending on the loss of the channel. HSPICE simulations are used to demonstrate the performance of the driver at 10, 20 and 40 Gbps data rates. At 40 Gbps, the driver is capable of equalizing a PRBS9 data pattern signal through a channel that has a loss of 9 dB. At worst case conditions and 40 Gbps date rate, the driver achieves a differential eye-opening amplitude of 201 mVppd and an eye-opening of 0.952 UI. The driver is designed using 28 nm CMOS process and uses a nominal 1 V supply voltage. It consumes a maximum of 12 mW of at-speed power.     

一种基于衬底驱动PMOS晶体管的低压共源共栅电流镜

基于衬底驱动PMOS晶体管设计了低压PMOS衬底驱动CMOS共源共栅电流镜电路(BDCCM),并讨论分析了其输入阻抗、输出阻抗和频率特性.基于TSMC 0.25μm 2P4M CMOS工艺的仿真和测试结果说明,BDCCM的最低输入压降要求只有0.3V,但是其输入输出线性度和频率带宽要比传统的共源共栅电流镜低,是低频低压CMOS模拟集成电路设计的新型高性能共源共栅电流镜.     

Comparison of high impedance input topologies with low EMI susceptibility

Different Input Topologies with resistance to electromagnetic interferences (EMI) are analyzed and compared in terms of EMI reduction. The emphasis in this study is put on circuit robustness and applicability to industrial applications, which requires sufficient EMI rejection over all process corners. Furthermore, a new topology based on a replica amplifier is introduced, that is more robust to process variation compared to previous works (Jean-Michel Redouté and Michiel Steyaert, ESSCIRC, Sept. 2008; Fiori, IEEE Transac Electromag Compat 49(4):834–839, 2007) that rely on accurate matching of absolute values in order to achieve efficient EMI cancellation.     

A new low voltage level-shifted FVF current mirror with enhanced bandwidth and output resistance

This paper proposes a new high-performance level-shifted flipped voltage follower (LSFVF) based low-voltage current mirror (CM). The proposed CM utilises the low-supply voltage and low-input resistance characteristics of a flipped voltage follower (FVF) CM. In the proposed CM, level-shifting configuration is used to obtain a wide operating current range and resistive compensation technique is employed to increase the operating bandwidth. The peaking in frequency response is reduced by using an additional large MOSFET. Moreover, a very high output resistance (in GΩ range) along with low-current transfer error is achieved through super-cascode configuration for a wide current range (0–440 µA). Small signal analysis is carried out to show the improvements achieved at each step. The proposed CM is simulated by Mentor Graphics Eldospice in TSMC 0.18 µm CMOS, BSIM3 and Level 53 technology. In the proposed CM, a bandwidth of 6.1799 GHz, 1% settling time of 0.719 ns, input and output resistances of 21.43 Ω and 1.14 GΩ, respectively, are obtained with a single supply voltage of 1 V. The layout of the proposed CM has been designed and post-layout simulation results have been shown. The post-layout simulation results for Monte Carlo and temperature analysis have also been included to show the reliability of the CM against the variations in process parameters and temperature changes.     

Low power high output impedance high bandwidth QFGMOS current mirror

Current mirror is a basic block of any mixed-signal circuit for example in an analog-to-digital converter. Its precise performance is the key requirement for analog circuits where offset is a measure issue. The key parameter which defines the performance of current mirror is its input/output impedance, input swing, and bandwidth. In this paper, a low power design of current mirror using quasi-floating gate MOS transistor is presented. The proposed current mirror boosts its output impedance in range of giga-ohm through use of regulated cascode structure followed by super-cascode. Another improvement is done in reduced input compliance voltage limits with the help of level shifter. The proposed current mirror operates well for input current range 0–700 $\mathrm{\mu }A$ with an input and output impedance of 160 $\Omega$ and 8.55 $\mathrm{G}\Omega$ respectively and high bandwidth of 4.05 $\mathrm{GHz}$. The total power consumption of the proposed current mirror is about 0.84 mW. The low power consumption with enhanced output impedance and bandwidth suits proposed current mirror for various high-speed analog designs. Performance of the presented current mirror circuit is verified using HSpice simulations on 0.18 $\mathrm{\mu }m$ mixed-mode twill-well technology at a supply voltage of ±0.5 V.     

A novel low voltage very low power CMOS class AB current output stage with ultra high output current drive capability

In this paper a novel low voltage (LV) very low power (VLP) class AB current output stage (COS) with extremely high linearity and high output impedance is presented. A novel current splitting method is used to minimize the transistors gate–source voltages providing LV operation and ultra high current drive capability. High linearity and very high output impedance are achieved employing a novel resistor based current mirror avoiding conventional cascode structures to be used. The operation of the proposed COS has been verified through HSPICE simulations based on TSMC 0.18 μm CMOS technology parameters. Under supply voltage of ±0.7 V and bias current of 5 μA, it can deliver output currents as high as 14 mA with THD better than ?53 dB and extremely high output impedance of 320 MΩ while consuming only 29 μW. This makes the proposed COS to have ultra large current drive ratio (I_outmax/I_bias or the ratio of peak output current to the bias current of output branch transistors) of 2800. By increasing supply voltage to ±0.9 V, it can deliver extremely large output current of ±24 mA corresponding to 3200 current drive ratio while consuming only 42.9 μW and exhibiting high output impedance of 350 MΩ. Interestingly, the proposed COS is the first yet reported one with such extremely high output current and a THD even less than ?45 dB. Such ultra high current drive capability, high linearity and high output impedance make the proposed COS an outstanding choice for LV, VLP and high drive current mode circuits. The superiority of the proposed COS gets more significance by showing in this work that conventional COS can deliver only ±3.29 mA in equal condition. The proposed COS also exhibits high positive and negative power supply rejection ratio (PSRR+/PSRR?) of 125 dB and 130 dB, respectively. That makes it very suitable for LV, VLP mixed mode applications. The Monte Carlo simulation results are provided, which prove the outstanding robust performance of the proposed block versus process tolerances. Favorably the proposed COS resolves the major limitation of current output stages that so far has prevented designing high drive current mode circuits under low supply voltages. In brief, the deliberate combination of so many effective novel methods presents a wonderful phenomenal COS block to the world of science and engineering.     

A bulk-driven quasi-floating gate FVF current mirror for low voltage,low power applications

This paper introduces a new low-voltage, low-power FVF current mirror circuit. The bulk-driven (BD) technique is employed to achieve extended input voltage swing and low supply voltage. Besides, the quasi-floating gate (QFG) is used to achieve high frequency performance. The merging of (BD) and (QFG) appear as a good and attractive solution to improve the circuit performance with reduced supply voltage. Benefiting from the interesting properties of (BD-QFG) MOSFET (MOST) technique, the proposed FVF current mirror circuit exhibits superior performance compared to other previously reported works. The workability of the proposed circuit has been verified through ELDO simulator based on a 0.18 μm USMC process. It achieves an enhanced bandwidth (2.7 GHz), low power consumption (79.33 μW), a low input impedance (130 Ω), and high output impedance (9.5 G Ω) from a low supply voltage (0.8 V). Monte Carlo simulation is also carried out, which proves the robust performance of the proposed circuit against mismatches. An application of the proposed current mirror is presented in the form of the current comparator to ensure the workability of the proposed BD-QFG current mirror.     

A Schmitt trigger with current mirror feedback

The circuit of a simple trigger with positive feedback via the current mirror (with gain) and the resistive divider is proposed. The circuit operation is described and the hysteresis voltage is obtained. The basic design limitations are introduced. Both versions (CMOS and bipolar) are considered.     

Quasi-floating gate MOSFET based low voltage current mirror

This paper demonstrates the use of quasi-floating gate MOSFET (QFGMOS) in the design of a low voltage current mirror and highlights its advantages over the floating gate MOSFET (FGMOS). The use of resistive compensation has been shown to enhance the bandwidth of QFGMOS current mirror. The proposed current mirror based on QFGMOS has a current range up to 500 μA with offset of 2.2 nA, input resistance of 235 Ω, output resistance of 117 kΩ, current transfer ratio of 0.98, dissipates 0.83 mW power and exhibits bandwidth of 656 MHz which increases to 1.52 GHz with resistive compensation. The theoretical and simulation results are in good agreement. The workability of the circuits has been verified using PSpice simulation for 0.13 μm technology with a supply voltage of ±0.5 V.     

一种基于恒定电流技术的具有低功耗和低失真的轨导轨输入输出放大器

本文提出了一种应用于音频信号处理的具有恒定的跨导Rail-to-Rail放大器,并且恒定跨导是通过一种恒定电流技术来实现。此技术是基于差分输入对工作在弱反型区。对于工作在弱反型区的MOSFET具有低失调和低功耗的优势。采用标准的0.35微米的CMOS工艺对电路进行流片,此芯片占有面积75×183 μm2。测试结果表明：在3.3V电源电压下,电路最大功耗为85.37mW;在2kHz时总谐波失真为1.2%。     

A low power and low distortion rail-to-rail input/output amplifier using constant current technique

A rail-to-rail amplifier with constant transconductance,intended for audio processing,is presented.The constant transconductance is obtained by a constant current technique based on the input differential pairs operating in the weak inversion region.MOSFETs working in the weak inversion region have the advantages of low power and low distortion.The proposed rail-to-rail amplifier,fabricated in a standard 0.35μm CMOS process,occupies a core die area of 75×183μm~2.Measured results show that the maximum power consumption is 85.37μW with a supply voltage of 3.3 V and the total harmonic distortion level is 1.2%at 2 kHz.