Cyclic Lateral Load Behavior of a Pile Cap and Backfill

A series of static cyclic lateral load tests were performed on a full-scale 4×3 pile group driven into a cohesive soil profile. Twelve 324-mm steel pipe piles were attached to a concrete pile cap 5.18×3.05?m in plan and 1.12?m in height. Pile–soil–pile interaction and passive earth pressure provided lateral resistance. Seven lateral load tests were conducted in total; four tests with backfill compacted in front of the pile cap; two tests without backfill; and one test with a narrow trench between the pile cap and backfill soil. The formation of gaps around the piles at larger deflections reduced the pile–soil–pile interaction resulting in a degraded linear load versus deflection response that was very similar for the two tests without backfill and the trenched test. A typical nonlinear backbone curve was observed for the backfill tests. However, for deflections greater than 5 mm, the load-deflection behavior significantly changed from a concave down shape for the first cycle to a concave up shape for the second and subsequent cycles. The concave up shape continued to degrade with additional cycles past the second and typically became relatively constant after five to seven cycles. A gap formed between the backfill soil and the pile cap, which contributed to the load-deflection degradation. Crack patterns and sliding surfaces were consistent with that predicted by the log spiral theory. The results from this study indicate that passive resistance contributes considerably to the lateral resistance. However, with cyclic loading the passive force degrades significantly for deflections greater than 0.5% of the pile cap height.     

Lateral Resistance of Short Single Piles and Pile Groups Located Near Slopes

Many transmission towers, high-rise buildings, and bridges are constructed near steep slopes and are supported by large-diameter piles. These structures may be subjected to large lateral loads, such as violent winds and earthquakes. Widely used types of foundations for these structures are pier foundations, which have large diameter with high stiffness. The behavior of a pier foundation subjected to lateral loads is similar to that of a short rigid pile, because both elements seem to fail by rotation developing passive resistance on opposite faces above and below the rotation point, unlike the behavior of a long flexible pile. This paper describes the results of several numerical studies performed with a three-dimensional finite-element method (FEM) of model tests and a prototype test of a laterally loaded short pile and pier foundation located near slopes, respectively. Initially, in this paper, the results of model tests of single piles and pile groups subjected to lateral loading, in homogeneous sand with 30° slopes and horizontal ground were analyzed by the three- dimensional (3D) finite-element (FE) analyses. Furthermore, field tests of a prototype pier foundation subjected to lateral loading on a 30° slope was reported. The FE analyses were conducted to simulate these results. The main purpose of this paper is the validation of the 3D elasto–plastic FEM by comparisons with the experimental data.     

Shaft Capacity of Open-Ended Piles in Sand

This paper presents the results from an experimental investigation designed to examine the effect of soil-core development and cyclic loading on the shaft resistance developed by open-ended piles in sand. An instrumented open-ended model pile was installed either by driving or jacking into an artificially-created loose sand deposit in Blessington, Ireland. The tests provided continuous measurements of the soil-core development and the radial effective stresses during installation and subsequent load tests. The equalized radial effective stresses developed at the pile-soil interface were seen to be dependent on the degree of soil displacement (plugging) experienced during installation, the distance from the pile toe, and the number of load cycles experienced by a soil element adjacent to the pile shaft. A new design method for estimating the shaft capacity of piles in sand is proposed and compared with measurements made on prototype field-scale piles.     

Undrained Lateral Pile Response in Sloping Ground

Three-dimensional finite element analyses were performed to study the behavior of piles in sloping ground under undrained lateral loading conditions. Piles of different diameter and length in sloping cohesive soils of different undrained shear strength and several ground slopes were considered. Based on the results of the finite element analyses, analytical formulations are derived for the ultimate load per unit length and the initial stiffness of hyperbolic p-y curves. New p-y criteria for static loading of piles in clay are proposed, which take into account the inclination of the slope and the adhesion of the pile-slope interface. These curves are used through a commercial subgrade reaction computer code to parametrically analyze the effect of slope inclination and pile adhesion on lateral displacements and bending moments. To validate the proposed p-y curves, a number of well documented lateral load tests are analyzed. Remarkable agreement is obtained between predicted and measured responses for a wide range of soil undrained shear strength and pile diameter, length, and stiffness.     

Behavior of Step Tapered Bored Piles in Sand under Static Lateral Loading

The behavior of step tapered bored piles in sand, under static lateral loading, was examined by field tests at one site in Kuwait. A total of 14 bored piles including two instrumented piles were installed for lateral loading. The soil profile consists of medium dense sand with weak cementations and no groundwater was encountered in the boreholes. Laboratory tests were carried out to determine the basic soil characteristics and the strength parameters. Both the ultimate lateral capacity and the deflections at applied loads were examined. The results indicate increased lateral load carrying capacity and decreased deflections at different applied loads for the step tapered piles due to the enlargement or strengthening of the upper section of the piles. The advantages of using this type of pile is emphasized including the cost saving resulting from an economical design.     

Lateral Behavior of Vertical Pile Group Embedded in Stabilized Earth Slope

An experimental study of the lateral behavior of vertical pile groups embedded in reinforced and nonreinforced sandy earth slopes was carried out. The model tests include studies of group configurations, pile spacing, embedment length of pile, relative densities of sand, and location of pile groups relative to the slope crest. Several configurations of geogrid reinforcement with different lengths, widths, and number of layers were used to reinforce a sandy slope of 1 (V): 1.5 (H). Pile groups of 2×2 and 3×3 along with center-to-center pile spacing of 2D, 3D, and 4.5D and piles with embedment length to diameter ratios of L/D = 12 and 22 were considered. Based on test results, geogrid parameters that give the maximum lateral capacity improvement are presented and discussed.     

Note on the Interaction Factor for Two Laterally Loaded Piles

This technical note revisits the interaction factors for two piles under lateral loading by means of a rigorous analytical method. The basic idea of the approach presented is to decompose the problem into an extended elastic soil and two fictitious piles having Young’s modulus equal to the difference between the modulus of the real pile and the surrounding soil. By considering the displacement compatibility condition, the pile–soil interaction problem is found to be governed by a Fredholm equation of the second kind. The displacement and bending moment distribution along the fictitious piles, and consequently, the desired interaction factor at the pile head are obtained. Comparison with existing solutions validates the accuracy of the present formulation and confirms that the conventional interaction factor approach would exaggerate the interaction effect for long flexible piles. Some numerical examples are presented to illustrate the influences of the pile spacing, pile–soil stiffness ratio, pile slenderness ratio, and departure angle of the loading direction on the calculated results. A set of interaction factor charts is also provided.     

Behavior of Laterally Loaded Large-Section Barrettes

A barrette is a large cross section rectangular pile. Due to dependence of the flexural stiffness of the rectangular section on its orientation and the nonlinear behavior of barrette materials, loading direction affects the lateral resistance of the barrette. Recently, full-scale lateral load tests were conducted on two barrettes in Hong Kong, one (DB1) with a cross section of 2.8 m by 0.86 m and a length of 51 m and the other (DB2) with a cross section of 2.7 m by 1.2 m and a length of approximately 30 m. This paper aims to investigate the response of laterally loaded large-section barrettes based on the load tests, to simulate the response of the two test barrettes, and to study the influence of loading direction on the lateral response of barrettes. Nonlinear p–y curves for soils and nonlinear stress–strain relations for barrette concrete and reinforcement are used to simulate the lateral response of the test barrettes considering five loading directions. The simulations were able to capture the apparently different behaviors before and after cracking of the barrette section. Sudden increases of displacement and rotation under a small lateral load increment and reduced depths of load transfer in the ground are predicted when the barrette section cracked. Based on this study, the direction of the resultant horizontal displacement is different from the loading direction if the barrette is not loaded along the major or minor axis of the cross section.     

Lateral Behavior of Pile Groups in Layered Soils

Assessment of the response of a laterally loaded pile group based on soil–pile interaction is presented in this paper. The behavior of a pile group in uniform and layered soil (sand and/or clay) is evaluated based on the strain wedge model approach that was developed to analyze the response of a long flexible pile under lateral loading. Accordingly, the pile’s response is characterized in terms of three-dimensional soil–pile interaction which is then transformed into its one-dimensional beam on elastic foundation equivalent and the associated parameter (modulus of subgrade reaction Es) variation along pile length. The interaction among the piles in a group is determined based on the geometry and interaction of the mobilized passive wedges of soil in front of the piles in association with the pile spacing. The overlap of shear zones among the piles in the group varies along the length of the pile and changes from one soil layer to another in the soil profile. Also, the interaction among the piles grows with the increase in lateral loading, and the increasing depth and fan angles of the developing wedges. The value of Es so determined accounts for the additional strains (i.e., stresses) in the adjacent soil due to pile interaction within the group. Based on the approach presented, the p–y curve for different piles in the pile group can be determined. The reduction in the resistance of the individual piles in the group compared to the isolated pile is governed by soil and pile properties, level of loading, and pile spacing.     

Passive Earth Pressure Mobilization during Cyclic Loading

The passive resistance measured in a series of full-scale tests on a pile cap is compared with existing theories. Four different soils were selected as backfill in front of the pile cap and the load-deflection relationships under cyclic loading were investigated. The log spiral theory provided the best agreement with the measured passive resistance. The Rankine theory significantly underestimated the passive force, while the Coulomb theory generally overestimated the resistance. The displacement necessary to mobilize the maximum passive force was compared with previous model and full-scale tests and ranged from 3.0 to 5.2% of the cap height. A hyperbolic model provided the best agreement with the measured backbone passive resistance curve compared with recommendations given by Caltrans and the U.S. Navy. However, this model overestimated the passive resistance for cyclic loading conditions due to the formation of a gap between the pile cap and backfill soil and backfill stiffness reduction. Based on the test results, the cyclic-hyperbolic model is developed to define load-deflection relationships for both virgin and cyclic loading conditions with the presence of a gap.     

Group Interaction Effects on Laterally Loaded Piles in Clay

This paper presents the results of static lateral load tests carried out on 1×2, 2×2, 1×4, and 3×3 model pile groups embedded in soft clay. Tests were carried out on piles with length to diameter ratios of 15, 30, and 40 and three to nine pile diameter spacing. The effects of pile spacing, number of piles, embedment length, and configuration on pile-group interaction were investigated. Group efficiency, critical spacing, and p multipliers were evaluated from the experimental study. The experimental results have been compared with those obtained from the program GROUP. It has been found that the lateral capacity of piles in 3×3 group at three diameter spacing is about 40% less than that of the single pile. Group interaction causes 20% increase in the maximum bending moment in piles of the groups with three diameter spacing in comparison to the single pile. Results indicate substantial difference in p multipliers of the corresponding rows of the linear and square pile groups. The predicted field group behavior is in good agreement with the actual field test results reported in the literature.     

Experimental Load–Transfer Curves of Laterally Loaded Piles in Nak-Dong River Sand

This paper describes the results of a model testing of the piles embedded in Nak-Dong River sand, located in south Korea, under monotonic lateral loadings. A number of features were studied, including the lateral resistance of piles, the effect of the installation method, and the pile head restraint condition. The study has led to recommendations of the load–transfer curves (p–y curves) for laterally loaded piles. Modification factors were developed to allow for both a different pile installation method and different pile head restraint conditions by comparison to existing model load tests. The proposed p–y curves were compared to the existing curves and were evaluated with the experimental data. The ultimate lateral soil resistance and subgrade modulus were investigated and discussed. It is revealed that the proposed p–y curves show significant differences in shapes and magnitudes when compared with existing p–y curve models. The accuracy of the proposed p–y curve model, considering the effect of installation method and pile head restraint condition, is very reasonable as shown by comparing measured and predicted lateral behavior of the pile.     

Simplified Lateral Load Analyses of Fixed-Head Piles and Pile Groups

The characteristic load method (CLM) can be used to estimate lateral deflections and maximum bending moments in single fixed-head piles under lateral load. However, this approach is limited to cases where the lateral load on the pile top is applied at the ground surface. When the pile top is embedded, as in most piles that are capped, the additional embedment results in an increased lateral resistance. A simple approach to account for embedment effects in the CLM is presented for single fixed-head piles. In practice, fixed-head piles are more typically used in groups where the response of an individual pile can be influenced through the adjacent soil by the response of other nearby piles. This pile–soil–pile interaction results in larger deflections and moments in pile groups for the same load per pile compared to single piles. A simplified procedure to estimate group deflections and moments was also developed based on the p-multiplier approach. Group amplification factors are introduced to amplify the single pile deflection and bending moment to reflect pile–soil–pile interaction. The resulting approach lends itself well to simple spreadsheet computations and provides good agreement with other generally accepted analytical tools and with values measured in published lateral load tests on groups of fixed-head piles.     

Numerical Investigation of the Effect of Vertical Load on the Lateral Response of Piles

The laboratory and field test data on the response of piles under the combined action of vertical and lateral loads is rather limited. The current practice for design of piles is to consider the vertical and lateral loads independent of each other. This paper presents some results from three-dimensional finite-element analyses that show the significant influence of vertical loads on a pile’s lateral response. The analyses were performed in both homogeneous clayey soils and homogeneous sandy soils. The results have shown that the influence of vertical loads on the lateral response of piles is to significantly increase the capacity in sandy soils and marginally decrease the capacity in clayey soils. In general, it was found that the effect of vertical loads in sandy soils is significant even for long piles, which are as long as 30 times the pile width, while in the case of clayey soils, the effect is not significant for piles beyond a length of 15 times the width of the pile. The design bending moments in the laterally loaded piles were also found to be dependent on the level of vertical load on the piles.     

Behavior of Slender Piles Subject to Free-Field Lateral Soil Movement

Soil movements associated with slope instability induce shear forces and bending moments in stabilizing piles that vary with the buildup of passive pile resistance. For such free-field lateral soil movements, stress development along the pile element is a function of the relative displacement between the soil and the pile. To investigate the effects of relative soil-pile displacement on pile response, large-scale load tests were performed on relatively slender, drilled, composite pile elements (cementitious grout with centered steel reinforcing bar). The piles were installed through a shear box into stable soil and then loaded by lateral translation of the shear box. The load tests included two pile diameters (nominal 115 and 178?mm) and three cohesive soil types (loess, glacial till, and weathered shale). Instrumentation indicated the relative soil-pile displacements and the pile response to the loads that developed along the piles. Using the experimental results, an analysis approach was evaluated using soil p-y curves derived from laboratory undrained shear strength tests. The test piles and analyses helped characterize behavioral stages of the composite pile elements at loads up to pile section failure and also provided a unique dataset to evaluate the lateral response analysis method for its applicability to slender piles.     

Nonlinear Efficiency of Bored Pile Group under Lateral Loading

A 3×3 bored pile group consisting of nine cast-in-drilled-hole reinforced concrete shafts and a comparable single-shaft were subjected to reversed cyclic, lateral head loading to investigate group interaction effects across a wide range of lateral displacements. The piles had the same diameter of d = 0.61?m and similar soil conditions; however, various equipment constraints led to two differences: (1) a fixed head (zero rotation) boundary condition for the single pile versus minor pile cap rotation in the vertical plane for the group and (2) shaft longitudinal reinforcement ratios of 1.8% for the single pile and 1% for the group piles. To enable comparisons between the test results, a calibrated model of the single pile (1.8% reinforcement) was developed and used to simulate the response of a single shaft with 1% reinforcement. Additional simulations of the pile group were performed to evaluate the effects of cap rotation on group response. By comparing the simulated responses for common conditions, i.e., 1% reinforcing ratio and zero head rotation, group efficiencies were found to range from unity at lateral displacements <0.004×d to 0.8 at small displacements ～ 0.01–0.02×d and up to 0.9 at failure (displacements >0.04×d). Hence, we find that group efficiency depends on the level of nonlinearity in the foundation system. The general group efficiency, although not its displacement-dependence, is captured by p-multipliers in the literature for reinforced concrete, fixed-head piles.     

Pile Spacing Effects on Lateral Pile Group Behavior: Load Tests

To investigate group interaction effects as a function of pile spacing, full-scale cyclic lateral load tests were performed on pile groups in stiff clay spaced at 3.3, 4.4, and 5.65 pile diameters in the direction of loading with as many as five rows of piles. Group interaction effects decreased considerably as pile spacing increased from 3.3 to 5.65D. Lateral resistance was a function of row location in the group, rather than location within a row. For a given deflection, the leading (first) row piles carried the greatest load, while the second and third row piles carried successively smaller loads. Fourth and fifth row piles carried about the same load as the third row piles. For a given load, the maximum bending moments in the trailing row piles were greater than those in the lead row, but these effects decreased as spacing increased. Cyclic loading reduced the peak load by about 15% after 15 cycles; however, distribution of load within the pile group was essentially the same as at the peak load. Gaps significantly reduced resistance for small deflections.     

Lateral Resistance of Single Pile Located Near Geosynthetic Reinforced Slope

An extensive program of laboratory tests was carried out to study the effect of reinforcing an earth slope on the lateral behavior of a single vertical pile located near the slope. Layers of geogrid were used to reinforce a sandy slope of 1 (V):1.5 (H) made with sands of three different unit weights representing dense, medium dense, and loose relative densities. Several configurations of geogrid reinforcement with different numbers of layers, vertical spacing, and length were investigated. The experimental program also included studies of the location of pile relative to the slope crest, relative density of sand, and embedment length of pile. The results indicate that stabilizing a soil slope has a significant benefit of improving the lateral load resistance of a vertical pile. The improvement in pile lateral load was found to be strongly dependent on the number of geogrid layers, layer size, and relative density of the sand. It was also found that soil reinforcement is more effective for piles located closer to the slope crest. Based on test results, critical values are discussed and recommended.     

Wedge Failure Analysis of Soil Resistance on Laterally Loaded Piles in Clay

A fundamental study of pile-soil systems subjected to lateral loads in clay soil was conducted by using experimental tests and a lateral load-transfer approach. The emphasis was on an improved wedge failure model developed by considering three-dimensional combination forces and a new hyperbolic p-y criterion. A framework for determining the p-y curve on the basis of both theoretical analysis and experimental load test results is proposed. The proposed p-y method is shown to be capable of predicting the behavior of a large-diameter pile under lateral loading. The proposed p-y curves with an improved wedge model are more appropriate and realistic for representing a pile-soil interaction for laterally loaded piles in clay than the existing p-y method.     

Data Reduction of Horizontal Load Full-Scale Tests on Bored Concrete Piles and Pile Groups

This paper proposes a new approach for data reduction of horizontal load full-scale tests on piles and pile groups. This approach has been developed on results from tests run on bored concrete piles embedded in homogeneous and nonhomogeneous ground. Due to nonlinear response of pile material and also to nonhomogeneous embedding ground, the problem of fitting reliable curves for representing strains along shafts is increased. It is suggested that B-splines fixed by a weighted least-squares algorithm should be used to overcome that problem. Taking advantage of the mathematical properties of B-splines, an algorithm for computing the internal force distribution amongst pile heads direct from test results is also proposed for pile groups. It is shown that the integration of the curvatures to compute pile movements should be done using natural boundary conditions instead of pile head measurements whenever possible. Despite the concrete crack, the distribution of bending moments can be computed from curvatures provided a reliable reinforced concrete model is used. Finally, it is proposed to compute the soil reactions by the integration of bending moments, solving an integral equation by again using B-spline functions.