Preparation and characterization of poly(ɛ-caprolactone) nonwoven mats via melt electrospinning

Laser melt electrospinning is a novel technology to produce nonwoven scaffolds for tissue engineering (TE) applications. This solvent-free process is far safer than common solution electrospinning. In this paper, we demonstrated the poly(?-caprolactone) (PCL) fibers diameters could be governed from 3 to 12 μm with changing electrospinning parameters. The various diameters can meet the needs of scaffold properties such as porosity, pore size, etc. Our experiential results also showed that the fibers diameter tended to decrease as laser current increased. The degradation of PCL molecular chains often occurs in the melt electrospinning process due to mechanical scission and thermal degradation. The crystallinity of as-spun PCL fibers was approximately equal to that of the annealing fibers by X-ray diffraction (XRD) and differential scanning calorimetry (DSC). In our experiential, the collected PCL electrospun fibers often fused together to form a three-dimension network structure, which is favorable to mechanical properties.     

Preparation and characterization of natural rubber/ultrafine full-vulcanized powdered styrene–butadiene rubber blends

In this paper, natural rubber (NR)/ultrafine full-vulcanized styrene–butadiene powdered rubber (UFPSBR) blends were prepared and studied for the first time. Scanning electron microscopy and thermogravimetric analysis were employed to characterize UFPSBR. Equilibrium swelling method was used to determine the crosslink density of NR/UFPSBR vulcanizates. The results on mechanical properties showed that when NR/UFPSBR ratio was 100/5, the formulation exhibited favorable performances compared to pure NR vulcanizates. The heat build-up temperature also decreased after adding UFPSBR into the NR formulation. In dynamic mechanical analysis, in the temperature range of ?10 to ?5 °C, loss factor (tanδ) values of NR/UFPSBR vulcanizates showed an increasing trend over the given temperature range and exhibited a peak value at approximate ?5 °C. This indicates that wet traction and rolling resistance of samples were improved after UFPSBR was added in NR. This research demonstrates that UFPSBR can be incorporated into a conventional NR formula to successfully improve the comprehensive performances and dynamic mechanical properties of NR formula.     

Physical interactions in macroporous scaffolds based on poly(?-caprolactone)/chitosan semi-interpenetrating polymer networks

Polycaprolactone (PCL) and chitosan (CHT) are immiscible polymers. However, biodegradable porous scaffolds of both polymers were obtained by combining different techniques based on the synthesis of semi-interpenetrating polymer networks (SemiIPNs) and melt processing. SemiIPNs were prepared through simultaneous precipitation of the polymer blend (PCL/CHT) and subsequent crosslinking of chitosan with tripolyphosphate (weight fractions of CHT up to 30 wt.%). High porosity PCL/CHT scaffolds with open pore structure and good interconnectivity were obtained. Mechanical properties, evaluated by dynamic-mechanical analysis, decrease as porosity increases. The physical interactions between functional groups of CHT and carbonyl groups of PCL were assessed by FTIR, the shifting of the main relaxation of PCL towards high temperatures as the fraction of CHT increases as well as the evolution of the thermal properties of the system.     

Preparation,properties, and laser processing of poly(ɛ-caprolactone)/poly(lactic acid) blends with addition of natural fibers as a potential for printing plates application

In this research, biodegradable blend of poly(ɛ-caprolactone) (PCL) and poly(lactic acid) (PLA) is proposed as a new material for the production of a printing plate for embossing process. Printing plates for embossing consist of raised printing elements and recessed nonimage elements. In production of printing plates, laser technology was used in order to form a relief printing plate. The embossing process is based on the principle of the pressure of the relief printing plate into the printing substrate, which causes the controlled deformation of the substrate and three-dimensional (3D) effect. Coir fibers (CFs) were added as a natural filler to PCL/PLA blends to improve and adjust the properties of produced blends. Scanning electron microscopy micrographs, dynamic mechanical analysis analysis, roughness, and hardness were measured on prepared materials, and 2D and 3D microscopy was conducted on laser engraved printing plates. Results have shown that the addition of CFs improved the mechanical properties of produced materials. DMA results indicate the semicrystalline structure of all prepared blends, and that the addition of CFs raises the elasticity of the composites. Laser engraving showed that it is possible to engrave the produced biodegradable materials and to use it as a material for production of printing plates.     

The effects of PCL diol molecular weight on properties of shape memory poly(ε-caprolactone) networks

Shape memory poly(ε-caprolactone) (PCL) networks with different molecular weights of PCL diol were prepared via thiol–ene reaction in this work. The highly efficient thiol–ene reaction ensured a uniform distribution of PCL chains between crosslinker, contributing well-defined network architecture with good mechanical and shape memory properties. ¹H NMR spectra were used to confirm that PCL diol was completely converted into acrylate-terminated PCL. Gel content experiment and Fourier-transform infrared showed that almost all samples exhibited virtually the complete crosslinking network due to the highly selective thiol–ene reaction between acrylate-terminated PCL and tetrathiol crosslinker. Differential scanning calorimetry and X-ray diffraction tests revealed that the melting temperature and crystallinity of the prepared PCL networks by using high molecular weight of PCL diol displayed a higher result compared to ones using low molecular weight. The dynamic mechanical analyzer results revealed that the storage modulus of the network dropped evidently across the thermal transition, these characteristics of the PCL network indicated that all exhibited a good shape memory effect. The shape fixing ability was kind of being affected by the PCL diol molecular weight, while the shape recovery ratio of all samples can almost reach 99% irrespective of the length of PCL diol. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47055.     

Effects of storage on thermomechanical properties of poly(ɛ-caprolactone) blends containing poly(vinyl pyrrolidone/iodine)

Abstract

This study reports the effects of: the molecular weight ratio of poly(?-caprolactone) (PCL) in blends containing polymer of high (50 000 g mol^-1 ) and low (4000 g mol^-1 ) molecular weight; the concentration (0, 1, and 5 wt-%) of poly(vinyl pyrrolidone/iodine) (PVP/I); and storage at 30°C and 75% relative humidity; on the thermomechanical properties of films prepared by solvent evaporation from solutions containing both PCL and PVP/I. The tensile properties were found to be statistically dependent on the molecular weight ratio of PCL but not on the concentration of PVP/I. The reductions in tensile strength and elongation at break associated with increasing amounts of low molecular weight PCL were attributed to a reduction in the concentration of chain entanglements. No changes were observed in viscoelastic properties or the glass transition temperature. Following storage there were no changes in the tensile strength, glass transition temperature, or viscoelastic properties of the films; however, significant reductions in elongation at break were observed. It is suggested that this is due to hydrolytic chain scission of amorphous PCL. Inclusion of 5 wt-% PVP/I increased this process in films containing 100 : 0 and 80 : 20 high/low molecular weight PCL (but not 60 : 40), but the extent of this was small. This study highlighted significant aging properties of PCL in a moist atmosphere. Consequently, it is recommended that suitable packaging materials should be employed to control the exposure of PCL films to water during storage.     

Physical properties and biodegradation of acrylic acid grafted poly(ε-caprolactone)/chitosan blends

We blended films of acrylic acid grafted polycaprolactone (PCLgAA) and citosan (CS) with different compositions from aqueous acetic acid solution. DSC measurements showed that the melting temperatures and enthalpies of the blends decreased with increasing CS content. From FTIR results, we observe that the amino groups of CS form covalent bonds with the carboxylic groups of PCLgAA in addition to hydrogen bonds between the constituents in the blends. Though the crystal structure of the PCLgAA component was not changed, as proved by WAXD results, blending CS suppressed the crystallinity of the blends. Furthermore, the ductility of CS was increased during tensile testing in PCLgAA/CS blends due to enhanced affinity between the two components. However, PCLgAA/CS blends show greater resistance than PCL/CS blends to biodegradation in an enzymatic environment.     

In situ photocrosslinkable nanohybrids based on poly(ε-caprolactone fumarate)/polyhedral oligomeric silsesquioxane: synthesis and characterization

Two types of biodegradable, in situ photocrosslinkable macromers were synthesized consisting a linear copolyester i.e., PCLF based on fumaric acid (FA) and poly(ε-caprolactone diol) (PCL diol), and its nanohybrid counterpart (POSS-PCLF) composed of FA, PCL diol and polyhedral oligomeric silsesquioxane (POSS). Chemical structure of the macromers was characterized by ¹HNMR and FTIR spectroscopy. The synthesized macromers were photocrosslinked by visible light irradiation in the presence of camphorquinone and N,N’-dimethylaminoethyl methacrylate as a photoinitiator and accelerator, respectively. Photocrosslinking characteristics of the compositions were investigated as a function of the initial PCL diol molecular weight, presence of POSS nanoparticles or N-vinylpyrrolidone (NVP, as a reactive diluent) by tracing degree of conversion by FTIR spectroscopy, equilibrium swelling studies. Thermal and dynamical properties of the macromers and the resulting networks were studied by TGA, DSC and DMA techniques pre- and post-photocrosslinking. In contrast to the self-crosslinkability of the macromers, the crosslinking reaction was promoted more efficiently in the presence of NVP as a reactive diluent. This scrutiny showed that there is an optimum point for POSS concentration to obtain the maximum improvement in the network properties.     

Synthesis and characterization of amphiphilic poly(ɛ-caprolactone)-b-polyphosphoester diblock copolymers bearing multifunctional pendant groups

A series of parent block copolyesters poly(?-caprolactone)-block-poly[2-(2-oxo-1, 3, 2-dioxaphospholoyloxy)ethyl acrylate] (PCL-b-POPEA) with different block lengths have been synthesized by ring-opening polymerization (ROP) and four kinds of mercaptans were then used in the postpolymerization modification via Michael-type addition reaction, resulting in several block copolyesters with various functionalities (e.g., hydroxyl, carboxyl, amine, and amino acid) in their pendant groups. The chemical structures of these block copolymers were characterized by FT-IR, NMR spectroscopy and GPC analysis. The self-assembly behaviors of PCL-b-POPEA have been studied by fluorescence probe technique, transmission electron microscopy (TEM) and high-performance particle size (HPPS) instrument. In vitro cytotoxicity test indicated that the block copolymers possess good biocompatibility. Initial in vitro drug loading and release studies using Doxorubicin (DOX) as a model drug demonstrated a faster release in the presence of phosphodiesterase I as compared to the system without enzyme. Moreover, it was found that DOX-loaded nanoparticles displayed higher inhibition to KB cell proliferation in comparison with free DOX. Therefore, the combination of ROP and Michael-type addition reaction provides a general access to various types of multifunctional and biodegradable materials.     

Effect of poly(ε-caprolactone) and titanium (IV) dioxide content on the UV and hydrolytic degradation of poly(lactic acid)/poly(ε-caprolactone) blends

The effect of accelerated weathering degradation on the properties of poly(lactic acid) (PLA)/poly(ε-caprolactone) (PCL) blends and PLA/PCL/titanium (IV) dioxide (TiO₂) nanocomposites are presented in this paper. The results show that both polymers are susceptible to weathering degradation, but their degradation rates are different and are also influenced by the presence of TiO₂ in the samples. Visual, microscopic and atomic force microsocpy observations of the surface after accelerated weathering tests confirmed that degradation occurred faster in the PLA/PCL blends than in the PLA/PCL/TiO₂ nanocomposites. The X-ray diffraction results showed the degradation of PCL in the disappearance of its characteristic peaks over weathering time, and also confirmed that PLA lost its amorphous character and developed crystals from the shorter chains formed as a result of degradative chain scission. It was further observed that the presence of TiO₂ retarded the degradation of both PLA and PCL. These results were supported by the differential scanning calorimetry results. The thermogravimetric analysis results confirmed that that PLA and PCL respectively influenced each other's thermal degradation, and that TiO₂ played a role in the thermal degradation of both PLA and PCL. The tensile properties of both PLA/PCL and PLA/PCL/TiO₂ were significantly reduced through weathering exposure and the incorporation of TiO₂.     

Impact of organoclays on the phase morphology and the compatibilization efficiency of immiscible poly(ethylene terephthalate)/poly(ε-caprolactone) blends

Adding nanofillers Cloisite 30B (C30B) and Cloisite 15A (C15A) to poly(ethylene terephthalate) (PET)/poly(ε-caprolactone) (PCL) (70/30, wt/wt) blends via melt blending can improve their phase morphology and change their interface properties. The effects of the different selective localization of clay on the structure and the morphologies are studied and evaluated by theoretical and experimental methods. It is found that C30B is selectively localized in PET and at the PET-PCL interface, whereas C15A is mainly localized at the interface. Moreover, the changes in the rheological behavior of the blends are attributed to the formation of clay network-like structures. X-ray diffraction, scanning electron microscope, and transmission electron micrograph observations also evidenced an exfoliated and/or intercalated structure of C30B, and intercalated structure of C15A in the blend, together with significant morphology changes of the initially immiscible blend. The relative permeability to PET/PCL of the nanocomposites decreased with the increasing of nanoclays content. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48812.     

Effect of the processing conditions and the addition of trans-polyoctenylene rubber on the properties of natural rubber/styrene–butadiene rubber blends

In this study, the influence of the processing conditions and the addition of trans-polyoctenylene rubber (TOR) on Mooney viscosity, tensile properties, hardness, tearing resistance, and resilience of natural rubber/styrene–butadiene rubber blends was investigated. The results obtained are explained in light of dynamic mechanical and morphological analyses. Increasing processing time produced a finer blend morphology, which resulted in an improvement in the mechanical properties. The addition of TOR involved an increase in hardness, a decrease in tear resistance, and no effect on the resilience. It resulted in a large decrease in the Mooney viscosity and a slight decrease in the tensile properties if the components of the compounds were not properly mixed. The results indicate that TOR acted more as a plasticizer than a compatibilizer. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of modified rubber powder on the morphology and thermal and mechanical properties of blown poly(lactic acid)–hydroxyl epoxidized natural rubber films for flexible film packaging

In this study, we prepared and used modified natural rubber powder to increase the toughness of poly(lactic acid) (PLA) films. We blended PLA and hydroxyl epoxidized natural rubber (HENR) via a melt-mixing process with twin-screw extruder and a blowing machine. We investigated the influence of the HENR content in the blend films on the microstructure, thermal, mechanical, and optical properties. The morphology of the blend showed a coarse surface and elongated fibrils of HENR in the PLA matrix. After blowing, the dispersion of small particles of HENR in the substrate was seen. The size of the remaining HENR particles was smaller than that of the starting powder. The compatibility of HENR and the remaining rubber particles may have synergistically contributed to improvements in the elongation at break, impact strength, and ultraviolet–visible transition protection of the PLA films. The elongation at break drastically increased from 3 to 228% after PLA was blended with 20 wt % HENR. On the other hand, all of the blends exhibited lower glass-transition temperatures and cold crystallization temperatures than the pure PLA films. We concluded that the blend was partially compatible and may have increased the flexibility of the PLA films. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47503.     

Preparation and characterization of polyseudorotaxanes based on adamantane-modified polybenzoxazines and β-cyclodextrin

β-Cyclodextrin (β-CD) forms inclusion complexes (ICs) with adamantane-modified benzoxazines (2 benzoxazine and 3 benzoxazine). These benzoxazines can readily penetrate into the CD's hydrophobic cavity, causing turbidity of their solutions, from which fine crystalline powders are obtained. We characterized these complexes by powder X-ray diffraction, ¹³C and ¹³C CP/MAS NMR spectroscopies, DSC, and TGA. The X-ray diffraction and solid-state ¹³C CP/MAS NMR spectroscopy indicate that the IC domains of the polypseudorotaxanes maintain their channel-type structures after the ring-opening curing reactions have occurred. Furthermore, DSC measurements indicate that complexing the adamantane-modified benzoxazine units with β-CDs result in stiffer main chains and, thus, higher glass transition temperature. TGA also indicates that the inclusion complexes have enhanced its thermal stability.     

Effects of modified silica on the co-vulcanization kinetics and mechanical performances of natural rubber/styrene–butadiene rubber blends

Rubber blends are widely used for combining the advantages of each rubber component. However, to date, how to determine and distinguish the vulcanization kinetics for each single rubber phase in rubber blends during the co-vulcanization process is still a challenge. Herein, high-resolution pyrolysis gas chromatography–mass spectrometry (HR PyGC-MS) was employed for the first time to investigate the vulcanization kinetics of natural rubber (NR) and styrene–butadiene rubber (SBR) in NR/SBR blends filled with modified silica (SiO₂). The reaction rates of crosslinking of each rubber phase in NR/SBR were calculated, which showed that the crosslinking rates of NR were much lower than those of SBR phase in the unfilled blends and blends filled with unmodified and silane modified silica. Interestingly, the vulcanization rates of NR and SBR phase were approximately same in the vulcanization accelerator modified silica filled blends, showing better co-vulcanization. In addition, the vulcanization accelerator modified silica was uniformly dispersed and endowed rubber blends with higher mechanical strength compared to the untreated silica. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48838.     

Development of novel hybrid nanocomposites based on natural biodegradable polymer–montmorillonite/polyaniline: preparation and characterization

The problems with non-degradable materials in different applications have led to an interest in materials based on bionanocomposites. In this study, polymer–montmorillonite nanocomposites based on natural polymers (chitosan, alginate, gelatin and starch) and montmorillonite (MMT) were prepared using solution intercalation method. Then hybrid nanocomposites were synthesized by chemical oxidative polymerization of aniline in the presence of polymer–MMT nanocomposites. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy (TEM) and thermogravimetric analysis (TGA) were employed to characterize the nanocomposites. FT-IR confirmed the successful preparation of hybrid nanocomposites. From the XRD results, intercalation of the MMT platelets in the matrix of polymers was examined. Further investigation by TEM images showed a mixed intercalated and flocculated structure for nanocomposites. Moreover, the TGA results showed improved thermal stability for the nanocomposites. The results presented in this study showed the feasibility of using these hybrid nanocomposites with improved properties in wide range of applications.     

Fabrication and characterization of poly(ε-caprolactone)/gelatin nanofibrous scaffolds for retinal tissue engineering

Different ratios of poly(ε-caprolactone) (PCL) and gelatinwere used to fabricate scaffolds for regeneration of retinal pigment epithelium (RPE) layer. Physical and chemical characterizations were performed and the behavior of human RPE cells on the scaffolds was evaluated subsequently. An increase in gelatin content in the scaffold enhanced hydrophilicity, RPE cell attachment, proliferation, and spreading over PCL scaffolds. Granular and cytoplasmic expressions of RPE65 and Cytokeratin 8/18 markers confirmed the presence of RPE cells. It was believed that PCL/gelatin scaffolds could be used as substrates to replace RPE extracellular matrix to facilitate regeneration of RPE layer in retinal diseases.     

Effects of processing conditions on hybrid filler selective localization,rheological, and thermal properties of poly(ε-caprolactone)/poly(lactic acid) blends

In this study, the effects of processing conditions through different mixing sequences were used to analyze the factors, which could influence the hybrid filler selective localization in an immiscible polymer blend and how localization can influence the rheological and thermal properties. Different selective localizations were observed depending on the mixing sequence used when the hybrid filler was added. Notably, nanoparticles can interact with each other, which favor a synergy between them and alters, besides the localization, the dispersion state, or can interact with one polymer phase, and also alter the nanoparticles' selective localization. An improvement in rheological properties was observed in the hybrid nanocomposite in which there was interaction between the nanoparticles, favoring the hexagonal boron nitride exfoliation. On the other hand, for the storage modulus and degree of crystallinity, the sharpest increase occurred in the hybrid nanocomposite in which the nanoparticles could interact preferably with one polymer phase. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 137, 48711.     

Biodegradable poly(l-lactide)/poly(?-caprolactone)-modified montmorillonite nanocomposites: Preparation and characterization

New nanocomposites were prepared by melt blending poly(l-lactide) (PLLA), poly(?-caprolactone) (PCL), and organically modified montmorillonite (OMMT). The obtained nanocomposites showed enhanced tensile strength, modulus and elongation at break than that of PLLA/PCL blends. The dynamic mechanical analysis showed the increasing mechanical properties with temperature dependence of nanocomposites. Wide-angle X-ray diffraction analysis and transmission electron microscopy indicated that the material formed the nanostructure. Adding OMMT improved the thermal stability and crystalline abilities of nanocomposites. The morphology was investigated by environmental scanning electron microscopy, which showed that increasing content of OMMT reduces the domain size of phase-separated particles. The specific interaction between each polymer and OMMT was characterized by the Flory-Huggins interaction parameter, B, which was determined by the equilibrium melting point depression of nanocomposites. The final values of B showed that PLLA was more compatible with OMMT than PCL.