Effects of low-temperature nitridation on the electrical conductivity and corrosion resistance of 446M stainless steel as bipolar plates for proton exchange membrane fuel cell

Low-temperature nitridation was used to form a protective and conductive layer on stainless steel. The surface characterization reveals that a continuous and protective Cr-nitride/oxide layer (CrN and Cr₂O₃) forms on the 446M stainless steel surface after low-temperature nitridation. The electrical conductivity of the sample is investigated in terms of the interfacial contact resistance. This value for nitrided 446M at low temperature is 6 mΩ cm², which is much lower than that of the bare 446M stainless steel (about 77 mΩ cm²) at a compaction force of 140 N/cm². The corrosion resistance of low-temperature nitrided 446M stainless steel is examined in potentiodynamic and potentiostatic tests under simulated polymer electrolyte membrane fuel cell (PEMFC) conditions with pH 3 H₂SO₄ at 80 °C. In a simulated anode condition, the current density is −1 × 10⁻⁶ A/cm². In a simulated cathode condition, the current density is 1 × 10⁻⁷ A/cm². Low-temperature nitrided 446M stainless steel shows superior electrical conductivity and corrosion resistance than bare 446M stainless steel.     

Protective nitride formation on stainless steel alloys for proton exchange membrane fuel cell bipolar plates

Gas nitridation has shown excellent promise to form dense, electrically conductive and corrosion-resistant Cr-nitride surface layers on Ni–Cr base alloys for use as proton exchange membrane fuel cell (PEMFC) bipolar plates. Due to the high cost of nickel, Fe-base bipolar plate alloys are needed to meet the cost targets for many PEMFC applications. Unfortunately, nitridation of Fe-base stainless steel alloys typically leads to internal Cr-nitride precipitation rather than the desired protective surface nitride layer formation, due to the high permeability of nitrogen in these alloys. This paper reports the finding that it is possible to form a continuous, protective Cr-nitride (CrN and Cr₂N) surface layer through nitridation of Fe-base stainless steel alloys. The key to form a protective Cr-nitride surface layer was found to be the initial formation of oxide during nitridation, which prevented the internal nitridation typically observed for these alloys, and resulted in external Cr-nitride layer formation. The addition of V to the alloy, which resulted in the initial formation of V₂O₃–Cr₂O₃, was found to enhance this effect, by making the initially formed oxide more amenable to subsequent nitridation. The Cr-nitride surface layer formed on model V-modified Fe–27Cr alloys exhibited excellent corrosion resistance and low interfacial contact resistance under simulated PEMFC bipolar plate conditions.     

Electrochemical nitridation of a stainless steel for PEMFC bipolar plates

AISI446 steel has been electrochemically nitrided in 0.1 M HNO₃ + 0.5 M KNO₃ solution at room temperature. XPS analysis revealed surface NH₃ and a deeper nitride layer. The surface layer of the stainless steel modified by electrochemical nitridation was thus composed of a nitrogen-incorporated oxide film. The nitrided steel showed very low interfacial contact resistance (ca. 18 mΩ cm² at 140 N/cm²) and excellent corrosion resistance in simulated PEMFC environments. Electrochemical nitridation provides an economic way to modify the stainless steel’s surface, and is very promising for application to fuel cell bipolar plates.     

Pre-oxidized and nitrided stainless steel alloy foil for proton exchange membrane fuel cell bipolar plates: Part 1. Corrosion, interfacial contact resistance, and surface structure

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr₂N, CrN, TiN, V₂N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of scale-up studies to determine the feasibility of extending the nitridation approach to thin 0.1 mm stainless steel alloy foils for proton exchange membrane fuel cell (PEMFC) bipolar plates. Developmental Fe-20Cr-4V alloy and type 2205 stainless steel foils were treated by pre-oxidation and nitridation to form low-ICR, corrosion-resistant surfaces. As-treated Fe-20Cr-4V foil exhibited target (low) ICR values, whereas 2205 foil suffered from run-to-run variation in ICR values, ranging up to 2× the target value. Pre-oxidized and nitrided surface structure examination revealed surface-through-layer-thickness V-nitride particles for the treated Fe-20Cr-4V, but near continuous chromia for treated 2205 stainless steel, which was linked to the variation in ICR values. Promising corrosion resistance was observed under simulated aggressive PEMFC anode- and cathode-side bipolar plate conditions for both materials, although ICR values were observed to increase. The implications of these findings for stamped bipolar plate foils are discussed.     

Anodic behavior of high nitrogen-bearing steels in PEMFC environments

High nitrogen-bearing stainless steels, AISI Type 201 and AL219, were investigated in simulated polymer electrolyte membrane fuel cell (PEMFC) environments to assess the use of these materials in fuel cell bipolar plate applications. Both steels exhibit better corrosion behavior than 316L steel in the same environments. Type 201 steel shows similar but lower interfacial contact resistance (ICR) than 316L, while AL219 steel shows higher ICR than 316L.

X-ray photoelectron spectroscopy (XPS) analysis shows that the air-formed films on Type 201 and AL219 are composed of iron oxides, chromium oxide, and manganese oxide. Iron oxides dominate the composition of the air-formed film, specially the outer layer. Chromium oxide dominates passive films. Surface film thicknesses were estimated. The results suggest that high nitrogen-bearing stainless steels are promising materials for PEMFC bipolar plates.     

Effect of chemical and heat treatment on the interfacial contact resistance and corrosion resistance of 446M ferritic stainless steel as a bipolar plate for polymer electrolyte membrane fuel cells

The bipolar plate is an important component of the polymer electrolyte membrane fuel cell (PEMFC) because it supplies the pathway of the electron flow between each unit cell. The ferritic stainless steel is considered a good candidate material for bipolar plate, but it is limited to use as a bipolar plate due to its corrosion problem and high interfacial contact resistance (ICR). To explore a cost-effective method of surface modification, various chemical and heat treatments are performed with 446M ferritic stainless steel to understand the effect of the surface modifications on the ICR and the corrosion resistance. The ICR and corrosion resistance of 446M stainless steel can be effectively controlled by a proper surface modification with combined treatment of immersion in the acidic solution, followed by heat treatment. The combined chemical and heat treatment not only improves the corrosion resistance but also reduces the ICR value.     

Ferritic stainless steels as bipolar plate material for polymer electrolyte membrane fuel cells

Both interfacial contact resistance (ICR) measurements and electrochemical corrosion techniques were applied to ferritic stainless steels in a solution simulating the environment of a bipolar plate in a polymer electrolyte membrane fuel cell (PEMFC). Stainless steel samples of AISI434, AISI436, AISI441, AISI444, and AISI446 were studied, and the results suggest that AISI446 could be considered as a candidate bipolar plate material. In both polymer electrolyte membrane fuel cell anode and cathode environments, AISI446 steel underwent passivation and the passive films were very stable. An increase in the ICR between the steel and the carbon backing material due to the passive film formation was noted. The thickness of the passive film on AISI446 was estimated to be 2.6 nm for the film formed at −0.1 V in the simulated PEMFC anode environment and 3.0 nm for the film formed at 0.6 V in the simulated PEMFC cathode environment. Further improvement in the ICR will require some modification of the passive film, which is dominated by chromium oxide.     

Effect of plastic deformation on the corrosion resistance of ferritic stainless steel as a bipolar plate for polymer electrolyte membrane fuel cells

Stainless steel is one of the best candidate materials for bipolar plate of polymer electrolyte membrane fuel cell (PEMFC) and there have been several manufacturing techniques for stainless steel bipolar plate. The deformation from manufacturing process for bipolar plate can induce the corrosion problem of bipolar plate. The deformed and the stamped stainless steels were examined by evaluating the corrosion resistance to understand the effect of the deformation on the stainless steel as a bipolar plate. The deformation of the stainless steel can significantly affect the corrosion resistance and the deformation from the shaping process for bipolar plate can induce the local anodic sites on the bipolar plate. Therefore, from the corrosion point of view, the shaping process for the bipolar plate is an important factor and the corrosion possibility by shaping process should be considered when selecting the optimum shaping method.     

Thermally nitrided Cu–5.3Cr alloy for application as metallic separators in PEMFCs

Cr-nitride which offers good electrical conductivity and corrosion resistance was formed on the surface of Cu–5.3 (wt.%)Cr alloy and its characteristic properties including electrochemical behavior and electrical conductivity were evaluated. The sample was annealed for 12 h in a temperature range of 600–1000 °C in a nitrogen atmosphere. Nitridation of Cr in Cu–5.3Cr alloy occurred at about 600 °C and followed Cr → Cr₂N → CrN phase transformation sequence. A continuous Cr-nitride was formed at 1000 °C, but not below 900 °C. Corrosion behavior of the continuously nitrided sample was investigated in simulated PEMFC environments. Corrosion resistance of the nitrided sample was improved in an anode environment, but not in a cathode environment. This was attributed to the dissolution of Cu through pin-hole defects on the surface of the nitrided sample just in the cathode environment. Interfacial contact resistance of the nitrided Cu–5.3Cr alloy was satisfied the target value. Furthermore, there was no recession of electrical conductivity after polarization.     

SnO2:F coated ferritic stainless steels for PEM fuel cell bipolar plates

Ferrite stainless steels (AISI441, AISI444, and AISI446) were successfully coated with 0.6 μm thick SnO₂:F by low-pressure chemical vapor deposition and investigated in simulated PEMFC environments. The results showed that a SnO₂:F coating enhanced the corrosion resistance of the alloys in PEMFC environments, though the substrate steel has a significant influence on the behavior of the coating. ICP results from the testing solutions indicated that fresh AISI441 had the highest dissolution rates in both environments, and coating with SnO₂:F significantly reduced the dissolution. Coating AISI444 also improved the corrosion resistance. Coating AISI446 steel further improved the already excellent corrosion resistance of this alloy. For coated steels, both potentiostatic polarizations and ICP results showed that the PEMFC cathode environment is much more corrosive than the anode one. More dissolved metallic ions were detected in solutions for PEMFC cathode environment than those in PEMFC anode environment. Sn²⁺ was detected for the coated AISI441 and AISI444 steels but not for coated AISI446, indicating that the corrosion resistance of the substrate has a significant influence on the dissolution of the coating. After coating, the ICR values of the coated steels increased compared to those of the fresh steels. The SnO₂:F coating seems add an additional resistance to the native air-formed film on these stainless steels.     

Chromium nitride/Cr coated 316L stainless steel as bipolar plate for proton exchange membrane fuel cell

Chromium nitride/Cr coating has been deposited on surface of 316L stainless steel to improve conductivity and corrosion resistance by physical vapor deposition (PVD) technology. Electrochemical behaviors of the chromium nitride/Cr coated 316L stainless steel are investigated in 0.05 M H₂SO₄ + 2 ppm F⁻ simulating proton exchange membrane fuel cell (PEMFC) environments, and interfacial contact resistance (ICR) are measured before and after potentiostatic polarization at anodic and cathodic operation potentials for PEMFC. The chromium nitride/Cr coated 316L stainless steel exhibits improved corrosion resistance and better stability of passive film either in the simulated anodic or cathodic environment. In comparison to 316L stainless steel with air-formed oxide film, the ICR between the chromium nitride/Cr coated 316L stainless steel and carbon paper is about 30 mΩ cm² that is about one-third of bare 316L stainless steel at the compaction force of 150 N cm⁻². Even stable passive films are formed in the simulated PEMFC environments after potentiostatic polarization, the ICR of the chromium nitride/Cr coated 316L stainless steel increases slightly in the range of measured compaction force. The excellent performance of the chromium nitride/Cr coated 316L stainless steel is attributed to inherent characters. The chromium nitride/Cr coated 316L stainless steel is a promising material using as bipolar plate for PEMFC.     

Plasma nitrided titanium as a bipolar plate for proton exchange membrane fuel cell

Plasma nitriding was applied to improve the surface performance of titanium bipolar plate. XRD and SEM results showed a titanium nitride layer was formed after nitridation. In comparison with pure titanium, the interfacial contact resistance of plasma nitrided titanium was reduced to some extent by the nitridation treatment. However, high corrosion current was observed under electrochemical tests in 0.5 M H₂SO₄ + 5 ppm HF. Both the electrical conductivity and corrosion resistance of the surface of plasma nitriding titanium did not reach the level of graphite. Some more improvements are expected in the plasma nitriding process or another surface modification on pure titanium.     

Thermal nitridation of chromium electroplated AISI316L stainless steel for polymer electrolyte membrane fuel cell bipolar plate

The electrical and corrosion properties of surface-nitrided AISI316L stainless steel are evaluated to assess the potential use of this material as a bipolar plate for a polymer electrolyte membrane fuel cell. Chromium is electroplated on the surface of the AISI316L stainless steel before nitridation. The nitriding condition is selected so as to form Cr₂N nitride only and the result is compared with that of a CrN + Cr₂N nitride coating. The stainless steels with the Cr₂N nitride protective coating layer exhibit better interfacial contact resistance and corrosion resistance than the as-rolled or (CrN + Cr₂N)-coated AISI316L stainless steels.     

Applicability of extra low interstitials ferritic stainless steels for bipolar plates of proton exchange membrane fuel cells

Ferritic stainless steels can be attractive bipolar plate materials of proton exchange membrane fuel cells (PEMFC), provided that the stainless steels show sufficient corrosion resistance, for instance, by eliminating interstitial elements such as carbon and nitrogen. In the present study, thus, ferritic stainless steels (19Cr2Mo and 22Cr2Mo) with extra low interstitials (ELI) are evaluated to determine the required level of chromium content to apply them for PEMFC bipolar plates. In a simulated PEMFC environment (0.05 M SO₄²⁻ (pH 3.3) + 2 ppm F⁻ solution at 353 K), the 22Cr2Mo stainless steel showed lower current density during the polarization in comparison with the 19Cr2Mo one. The polarization behavior of the 22Cr2Mo stainless steel resembles that of the type 316 one (17Cr12Ni2Mo). Similar values of interfacial contact resistance (ICR) are observed for both ferritic stainless steels. The 22Cr2Mo stainless steel bipolar plate is found to be stable throughout the cell operation, while the 19Cr2Mo stainless steel corroded within 1000 h. After the cell operation, the 22Cr2Mo stainless steel retains the chromium enriched passive film, while the chromium enriched surface film is not found for the 19Cr2Mo one, showing iron oxide/hydroxide based film. X-ray fluorescence (XRF) analysis of the membrane electrode assemblies (MEAs) after the cell operation indicates that the 22Cr2Mo stainless steel was less contaminated with iron species. The above results suggest that the 22Cr2Mo stainless steel can be applicable to bipolar plates for PEMFC, especially 22 mass% of chromium content in ferritic stainless steel with ELI system is, at least, demanded to ensure stable cell performance.     

Improved anticorrosion properties and electrical conductivity of 316L stainless steel as bipolar plate for proton exchange membrane fuel cell by lower temperature chromizing treatment

The lower temperature chromizing treatment is developed to modify 316L stainless steel (SS 316L) for the application of bipolar plate in proton exchange membrane fuel cell (PEMFC). The treatment is performed to produce a coating, containing mainly Cr-carbide and Cr-nitride, on the substrate to improve the anticorrosion properties and electrical conductivity between the bipolar plate and carbon paper. Shot peening is used as the pretreatment to produce an activated surface on stainless steel to reduce chromizing temperature. Anticorrosion properties and interfacial contact resistance (ICR) are investigated in this study. Results show that the chromized SS 316L exhibits better corrosion resistance and lower ICR value than those of bare SS 316L. The chromized SS 316L shows the passive current density about 3E−7 A cm⁻² that is about four orders of magnitude lower than that of bare SS 316L. ICR value of the chromized SS 316L is 13 mΩ cm² that is about one-third of bare SS 316L at 200 N cm⁻² compaction forces. Therefore, this study clearly states the performance advantages of using chromized SS 316L by lower temperature chromizing treatment as bipolar plate for PEMFC.     

Characterization and performance of UNS S63019 (21-4N) as bipolar plate material in a simulated polymer electrolyte membrane fuel cell environment

The austenitic stainless steel UNS S63019 was evaluated regarding its potential as bipolar plate material in a polymer electrolyte membrane fuel cell (PEMFC) environment. Segregated grains of niobium carbide (NbC_x) were identified in polished cross-sections of the alloy, offering a possible pathway for enhanced electrical conductivity through the passive surface oxide. Additionally, the alloy was tested for corrosion resistance in a simulated PEMFC environment. It was considered that perhaps the elevated nitrogen concentration in the alloy would provide some benefit for corrosion resistance.Results for interfacial contact resistance (ICR) testing of the air-formed surface film on UNS S63019 showed decreased electrical conductivity as compared to UNS S30400. Niobium carbide particles did not improve film conductivity due to a non-conductive niobium oxide layer that formed on the surface. Corrosion resistance of the alloy was also poor as compared with UNS S30400, demonstrating that elevated nitrogen concentration in the alloy was not adequate in itself to enhance corrosion resistance. Poor corrosion resistance was attributed primarily to high carbon content in the alloy which combined with a significant amount of chromium to form carbides.     

Effect of immersion in NaOH solution on ferritic stainless steel as a bipolar plate for polymer electrolyte membrane fuel cells

The surface of 446M ferritic stainless steel (FSS) is modified by immersing in NaOH solution to understand its effect on the interfacial contact resistance (ICR) and corrosion. Immersion in NaOH solution under optimum condition can lead to decrease the ICR value of 446M FSS with no decrease in the corrosion resistance. Immersion of 446M FSS in NaOH solution increases the ratio of Cr oxy-hydroxide/oxide, which contributes to decrease the ICR value. This means that the bound water present in the form of the OH⁻ group in the passive film acts as a donor-type impurity and provides the active sites for electrical conduction in the oxide. This imparts positive effect on the electrical conduction and leads to decrease in the ICR value even after the long-term immersion in the simulated PEMFC environment.     

Growth of Cr-Nitrides on commercial Ni–Cr and Fe–Cr base alloys to protect PEMFC bipolar plates

Nitridation of Cr-bearing alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant CrN or Cr₂N base surfaces of interest for a range of electrochemical devices, including fuel cells, batteries, and sensors. This paper presents results of exploratory studies of the nitridation of commercially available, high Cr (30–35 wt%) Ni–Cr alloys and a ferritic high Cr (29 wt%) stainless steel for proton exchange membrane fuel cell (PEMFC) bipolar plates. A high degree of corrosion resistance in sulfuric acid solutions designed to simulate bipolar plate conditions and low ICR values were achieved. Oxygen impurities in the nitriding environment were observed to play a significant role in the nitrided surface structures that formed, with detrimental effects for the Ni–Cr base alloys, but beneficial effects for the stainless steel alloy. Positive results from single-cell fuel cell testing are also presented.     

Effect of pH value on corrosion resistance and surface conductivity of plasma‐nitrided 304L bipolar plate for PEMFC

Low temperature plasma nitriding is developed to meet the requirements for corrosion resistance and interfacial contact resistance (ICR) of stainless steel 304L as the bipolar plate for PEMFC. A dense and supersaturated‐nitrogen nitrided layer has formed on the surface of the stainless steel 304L. Electrochemical behavior for the untreated and plasma‐nitrided 304L was measured in H₂SO₄ (pH=1–5)+2 ppm F^? simulating PEMFC environment, and the ICR was evaluated before and after corrosion tests. The experimental results have shown that the ICR for the plasma nitrided 304L is lower than the requirement of U.S. DOE (<10 mΩ cm² to 2010). Corrosion resistance and the ICR at the compaction force of 150–200 N cm^?2 increase with increasing pH value for the untreated and plasma‐nitrided 304L. The passive current densities for the untreated and plasma‐nitrided 304L are all lower than 16 µA cm^?2. The ICR between passive film and carbon paper are increased markedly because of passive film formed on the surface of both studied 304L. However, the passive current density and the ICR are lower for the plasma nitrided 304L than those for the untreated one at the given pH value, which results from the different composition of the stable passive film formed on the surface. The low temperature plasma nitriding provides a promising method for 304L using as bipolar plate for PEMFC. Further research is needed to evaluate the long‐term stability of passive film and the performance of single fuel cell. Copyright © 2010 John Wiley & Sons, Ltd.     

Ag–polytetrafluoroethylene composite coating on stainless steel as bipolar plate of proton exchange membrane fuel cell

Forming a coating on metals by surface treatment is a good way to get high performance bipolar plate of proton exchange membrane fuel cell (PEMFC). In our research, Ag–polytetrafluoroethylene (PTFE) composite film was electrodeposited with silver-gilt solution of nicotinic acid by a bi-pulse electroplating power supply on 316 L stainless steel bipolar plate of PEMFC. Surface topography, contact angle, interfacial conductivity and corrosion resistance of the bipolar plate samples were investigated. Results showed that the defects on the Ag–PTFE composite coating are greatly reduced compared with those on the pure Ag coating fabricated under the same condition; and the contact angle of the Ag–PTFE composite coating with water is 114°, which is much bigger than that of the pure Ag coating (73°). In addition, the interfacial contact resistance of the composite coating stays as low as the pure Ag coating; and the bipolar plate sample with composite coating shows a close corrosion resistance to the pure Ag coating sample in potentiodynamic and potentiostatic tests. Coated 316 L stainless steel plate with Ag–PTFE composite coating exhibits well hydrophobic characteristic, less defects, high interfacial conductivity and good corrosion resistance, which shows a great potential of the application in PEMFC.