共查询到20条相似文献,搜索用时 0 毫秒
1.
《International Journal of Hydrogen Energy》2020,45(46):24917-24927
The U.S. Department of Energy (DOE) has developed the Framework model to simulate fuel cell-based light-duty vehicle operation for various hydrogen storage systems. This transient model simulates the performance of the storage system, fuel cell, and vehicle for comparison to DOE's Technical Targets using four drive cycles. Metal hydride hydrogen storage models have been developed for the Framework model. Despite the utility of this model, it requires that material researchers input system design specifications that cannot be easily estimated. To address this challenge, a design tool has been developed that allows researchers to directly enter physical and thermodynamic metal hydride properties into a simple sizing module that then estimates the systems parameters required to run the storage system model. This design tool can also be used as a standalone MS Excel model to estimate the storage system mass and volume outside of Framework and compare it to the DOE Technical Targets. This model will be explained and exercised with existing hydrogen storage materials. 相似文献
2.
Fuel cell vehicles have a high potential to reduce both energy consumption and carbon dioxide emissions. However, due to the low density, hydrogen gas limits the amount of hydrogen stored on board. This restriction also prevents wide penetration of fuel cells. Hydrogen storage is the key technology towards the hydrogen society. Currently high-pressure tanks and liquid hydrogen tanks are used for road tests, but both technologies do not meet all the requirements of future fuel cell vehicles. This paper briefly explains the current status of conventional technologies (simple containment) such as high-pressure tank systems and cryogenic storage. Another method, hydrogen-absorbing alloy has been long investigated but it has several difficulties for the vehicle applications such as low temperature discharge characteristics and quick charge capability due to its reaction heat. We tested a new idea of combining metal hydride and high pressure. It will solve some difficulties and improve performance such as gravimetric density. This paper describes the latest material and system development. 相似文献
3.
《International Journal of Hydrogen Energy》2020,45(14):7958-7967
The “low-temperature” intermetallic hydrides with hydrogen storage capacities below 2 wt% can provide compact H2 storage simultaneously serving as a ballast. Thus, their low weight capacity, which is usually considered as a major disadvantage to their use in vehicular H2 storage applications, is an advantage for the heavy duty utility vehicles. Here, we present new engineering solutions of a MH hydrogen storage tank for fuel cell utility vehicles which combines compactness, adjustable high weight, as well as good dynamics of hydrogen charge/discharge. The tank is an assembly of several MH cassettes each comprising several MH containers made of stainless steel tube with embedded (pressed-in) perforated copper fins and filled with a powder of a composite MH material which contains AB2- and AB5-type hydride forming alloys and expanded natural graphite. The assembly of the MH containers staggered together with heating/cooling tubes in the cassette is encased in molten lead followed by the solidification of the latter. The tank can provide >2 h long H2 supply to the fuel cell stack operated at 11 kWe (H2 flow rate of 120 NL/min). The refuelling time of the MH tank (T = 15–20 °C, P(H2) = 100–150 bar) is about 15–20 min. 相似文献
4.
《International Journal of Hydrogen Energy》2021,46(79):39509-39522
The high price of hydrogen fuel in the fuel cell vehicle refuelling market is highly dependent on the one hand from the production costs of hydrogen and on the other from the capital cost of a hydrogen refuelling station's components to support a safe and adequate refuelling process of contemporary fuel cell vehicles. The hydrogen storage technology dominated in the vehicle sector is currently based on high-pressure compressed hydrogen tanks to extend as much as possible the driving range of the vehicles. However, this technology mandates the use of large hydrogen compression and cooling systems as part of the refuelling infrastructure that consequently increase the final cost of the fuel. This study investigated the prospects of lowering the refuelling cost of small urban hydrogen vehicles through the utilisation of metal hydride hydrogen storage. The results showed that for low compression hydrogen storage, metal hydride storage is in favour in terms of the dispensed hydrogen fuel price, while its weight is highly comparable to the one of a compressed hydrogen tank. The final refuelling cost from the consumer's perspective however was found to be higher than the compressed gas due to the increased hydrogen quantity required to be stored in fully empty metal hydride tanks to meet the same demand. 相似文献
5.
《International Journal of Hydrogen Energy》2019,44(55):29263-29272
We describe a metal hydride (MH) hydrogen storage tank for light fuel cell vehicle application developed at HySA Systems. A multi-component AB2-type hydrogen storage alloy was produced by vacuum induction melting (10 kg per a load) at our industrial-scale facility. The MH alloy has acceptable H sorption performance, including reversible H storage capacity up to ∼170 NL/kg (1.5 wt% H). The cassette-type MH tank was made up of 2 cylindrical aluminium canisters with transversal internal copper fins and external aluminium fins for improving the heat exchange between the heating medium and the MH tank. Heat supply and removal was provided from the outside using air at T = 15–25 °C. The MH tank was tested at the conditions of natural or forced (velocity ∼2 m/s) air convection. The tests included H2 charge of the tank at P = 15–40 bar and its discharge at P = 1 bar. The tank in the H2 discharge mode was also tested together with open cathode low-temperature proton exchange membrane fuel cell (LT PEMFC). 相似文献
6.
Energy efficiency, vehicle weight, driving range, and fuel economy are compared among fuel cell vehicles (FCV) with different types of fuel storage and battery-powered electric vehicles. Three options for onboard fuel storage are examined and compared in order to evaluate the most energy efficient option of storing fuel in fuel cell vehicles: compressed hydrogen gas storage, metal hydride storage, and onboard reformer of methanol. Solar energy is considered the primary source for fair comparison of efficiencies for true zero emission vehicles. Component efficiencies are from the literature. The battery powered electric vehicle has the highest efficiency of conversion from solar energy for a driving range of 300 miles. Among the fuel cell vehicles, the most efficient is the vehicle with onboard compressed hydrogen storage. The compressed gas FCV is also the leader in four other categories: vehicle weight for a given range, driving range for a given weight, efficiency starting with fossil fuels, and miles per gallon equivalent (about equal to a hybrid electric) on urban and highway driving cycles. 相似文献
7.
José Miguel Pasini Claudio Corgnale Bart A. van Hassel Theodore Motyka Sudarshan Kumar Kevin L. Simmons 《International Journal of Hydrogen Energy》2013
The United States Department of Energy (DOE) has published a progression of technical targets to be satisfied by on-board rechargeable hydrogen storage systems in light-duty vehicles. By combining simplified storage system and vehicle models with interpolated data from metal hydride databases, we obtain material-level requirements for metal hydrides that can be assembled into systems that satisfy the DOE targets for 2017. We assume minimal balance-of-plant components for systems with and without a hydrogen combustion loop for supplemental heating. Tank weight and volume are driven by the stringent requirements for refueling time. The resulting requirements suggest that, at least for this specific application, no current on-board rechargeable metal hydride satisfies these requirements. 相似文献
8.
《International Journal of Hydrogen Energy》2019,44(23):11574-11583
This paper designs an off-grid charging station for electric and hydrogen vehicles. Both the electric and hydrogen vehicles are charged at the same time. They appear as two electrical and hydrogen load demand on the charging station and the charging station is powered by solar panels. The output power of solar system is separated into two parts. On part of solar power is used to supply the electrical load demand (to charge the electric vehicles) and rest runs water electrolyzer and it will be converted to the hydrogen. The hydrogen is stored and it supplies the hydrogen load demand (to charge the hydrogen-burning vehicles). The uncertainty of parameters (solar energy, consumed power by electrical vehicles, and consumed power by hydrogen vehicles) is included and modeled. The fuel cell is added to the charging station to deal with such uncertainty. The fuel cell runs on hydrogen and produces electrical energy to supply electrical loading under uncertainties. The diesel generator is also added to the charging station as a supplementary generation. The problem is modeled as stochastic optimization programming and minimizes the investment and operational costs of solar and diesel systems. The introduced planning finds optimal rated powers of solar system and diesel generator, operation pattern for diesel generator and fuel cell, and the stored hydrogen. The results confirm that the cost of changing station is covered by investment cost of solar system (95%), operational cost of diesel generator (4.5%), and investment cost of diesel generator (0.5%). The fuel cell and diesel generator supply the load demand when the solar energy is zero. About 97% of solar energy will be converted to hydrogen and stored. The optimal operation of diesel generator reduces the cost approximately 15%. 相似文献
9.
《International Journal of Hydrogen Energy》2021,46(72):35896-35909
The goal of the EU Horizon 2020 RISE project 778307 “Hydrogen fuelled utility vehicles and their support systems utilising metal hydrides” (HYDRIDE4MOBILITY), is in addressing critical issues towards a commercial implementation of hydrogen powered forklifts using metal hydride (MH) based hydrogen storage and PEM fuel cells, together with the systems for their refuelling at industrial customers facilities. For these applications, high specific weight of the metallic hydrides has an added value, as it allows counterbalancing of a vehicle with no extra cost. Improving the rates of H2 charge/discharge in MH on the materials and system level, simplification of the design and reducing the system cost, together with improvement of the efficiency of system “MH store-FC”, is in the focus of this work as a joint effort of consortium uniting academic teams and industrial partners from two EU and associated countries Member States (Norway, Germany, Croatia), and two partner countries (South Africa and Indonesia).The work within the project is focused on the validation of various efficient and cost-competitive solutions including (i) advanced MH materials for hydrogen storage and compression, (ii) advanced MH containers characterised by improved charge-discharge dynamic performance and ability to be mass produced, (iii) integrated hydrogen storage and compression/refuelling systems which are developed and tested together with PEM fuel cells during the collaborative efforts of the consortium.This article gives an overview of HYDRIDE4MOBILITY project focused on the results generated during its first phase (2017–2019). 相似文献
10.
Terry A. Johnson Michael P. Kanouff Daniel E. Dedrick Gregory H. Evans Scott W. Jorgensen 《International Journal of Hydrogen Energy》2012
Sandia and General Motors have successfully designed, fabricated, and experimentally operated a vehicle-scale hydrogen storage demonstration system using sodium alanates. The demonstration system module design and the system control strategies were enabled by experiment-based, computational simulations that included heat and mass transfer coupled with chemical kinetics. Module heat exchange systems were optimized using multi-dimensional models of coupled fluid dynamics and heat transfer. Chemical kinetics models were coupled with both heat and mass transfer calculations to design the sodium alanate vessels. Fluid flow distribution was a key aspect of the design for the hydrogen storage modules and computational simulations were used to balance heat transfer with fluid pressure requirements. 相似文献
11.
On-board hydrogen storage systems employing high-pressure metal hydrides promise advantages including high volumetric capacities and cold start capability. In this paper, we discuss the development of a system simulation model in Matlab/Simulink platform. Transient equations for mass balance and energy balance are presented. Appropriate kinetic expressions are used for the absorption/desorption reactions for the Ti1.1CrMn metal hydride. During refueling, the bed is cooled by passing a coolant through tubes embedded within the bed while during driving, the bed is heated by pumping the radiator fluid through same set of tubes. The feasibility of using a high-pressure metal hydride storage system for automotive applications is discussed. Drive cycle simulations for a fuel cell vehicle are performed and detailed results are presented. 相似文献
12.
José Miguel Pasini Bart A. van Hassel Daniel A. Mosher Michael J. Veenstra 《International Journal of Hydrogen Energy》2012
In the global efforts to develop advanced materials-based hydrogen storage, the various on-board reversible hydrides, adsorbents and chemical storage candidate materials and systems each have their individual strengths and weaknesses. An overarching challenge in associated research and development is to devise material/system architectures which satisfy all requirements for viability in a particular application area, such as light-duty vehicular transportation. System modeling at the level which encompasses not only the storage material and vessel/reactor, but also integration with a fuel cell and balance-of-plant components, provides a more complete assessment of viability and guides options for improvement. The current work covers the methodology developed for conducting such system modeling consistently across multiple organizations and will present performance results from studies focused on reversible hydride systems. Connecting this high level modeling to more detailed finite element design simulations will be one aspect of our framework approach. The complex hydride NaAlH4 is representative of novel materials under development and will be used as the basis for properties, such as temperature dependent kinetics, which influence the integrated system configurations and component sizing. While system charging is included through the sizing of certain components, emphasis is placed on hydrogen discharge by the storage system, interrogated through drive cycle transients. Comparisons of performance relative to requirements, including effective gravimetric capacity, effective volumetric density and energy utilization, are given for the baseline material and for a sensitivity study on material density. 相似文献
13.
《International Journal of Hydrogen Energy》2019,44(29):15118-15134
The need for the enhancement of alternative energy sources is increasingly recognised and, in this perspective, the achievement of hydrogen economy seems to be fundamental. In this regard, fuel cells represent an interesting option for small and medium scale distributed renewable generation; however, these systems are inextricably linked with the concept of hydrogen storage. Research on metal hydrides revealed the opportunity to use these materials as basic elements in hydrogen storage devices, called MH systems. This means that interest exists in investigating the behaviour of metal hydrides: in fact, MH system operation is based on the hydriding/dehydriding reactions hydrides undergo, and, with the aim of evaluating the performance of such devices, these processes must be discussed and modelled.In the light of this, a simple numerical model to study hydride-based storage systems and their integration with fuel cells was developed: two low-temperature hydrides (LaNi5, LaNi4·8Al0.2) and two high-temperature hydrides (Mg, Mg2Ni) were selected and their behaviours in a MH system were simulated and compared with the help of such a model. This is an essential step in identifying the hydrides more suited to the application in question. Results showed that the choice is the trade off between encumbrance and reaction times; this implies that low-temperature hydrides are preferable because their encumbrance is limited and their reaction temperature range grants a greater versatility in small scale generation. 相似文献
14.
《International Journal of Hydrogen Energy》2022,47(45):19865-19875
Maritime industry has led renewable energy sources for the greener environment and efficient vehicles that effect by increasing population and energy demands. Hydrogen is one of the most popular of these renewable energy sources and one of the most favourable research area, worldwide. In this study, authors reported the usage of hydrogen fuel cells in marine transport as main power forwarder, their advantages and challenges under the lights on state of art and furthermore new technologies perspective. The latest research activities, hydrogen production and storage methods with challenges are analyzed and the developments of fuel cell based marine vehicles are discussed. In detailed, newly approachment of electrolyses from seawater for sustainable fuel necessity is discussed. As a result, this forseen study is important in terms of handling energy from seawater and compiling the latest technology for marine transport. 相似文献
15.
《International Journal of Hydrogen Energy》2022,47(69):29847-29857
This work combines materials development with hydrogen storage technology advancements to address onboard hydrogen storage challenges in light-duty vehicle applications. These systems are comprised of the vehicle requirements design space, balance of plant requirements, storage system components, and materials engineering culminating in the development of an Adsorbent System Design Tool that serves as a preprocessor to the storage system and vehicle-level models created within the Hydrogen Storage Engineering Center of Excellence. Computational and experimental efforts were integrated to evaluate, design, analyze, and scale potential hydrogen storage systems and their supporting components against the Department of Energy 2020 and Ultimate Technical Targets for Hydrogen Storage Systems for Light Duty Vehicles. Ultimately, the Adsorbent System Design Tool was created to assist material developers in assessing initial design parameters that would be required to estimate the performance of the hydrogen storage system once integrated with the full fuel cell system. 相似文献
16.
Anurag Singh M.P. Maiya S. Srinivasa Murthy 《International Journal of Hydrogen Energy》2017,42(22):15226-15235
The absorption and desorption performances of a solid state (metal hydride) hydrogen storage device with a finned tube heat exchanger are experimentally investigated. The heat exchanger design consists of two “U” shaped cooling tubes and perforated annular copper fins. Copper flakes are also inserted in between the fins to increase the overall effective thermal conductivity of the metal hydride bed. Experiments are performed on the storage device containing 1 kg of hydriding alloy LaNi5, at various hydrogen supply pressures. Water is used as the heat transfer fluid. The performance of the storage device is investigated for different operating parameters such as hydrogen supply pressure, cooling fluid temperature and heating fluid temperature. The shortest charging time found is 490 s for the absorption capacity of 1.2 wt% at a supply pressure of 15 bar and cooling fluid temperature and velocity of 288 K and 1 m/s respectively. The effect of copper flakes on absorption performance is also investigated and compared with a similar storage device without copper flakes. 相似文献
17.
Kriston P. Brooks Samuel J. Sprik David A. Tamburello Matthew J. Thornton 《International Journal of Hydrogen Energy》2018,43(18):8846-8858
The U.S. Department of Energy (DOE) developed a vehicle Framework model to simulate fuel cell-based light-duty vehicle operation for various hydrogen storage systems. This transient model simulates the performance of the storage system, fuel cell, and vehicle for comparison to Technical Targets established by DOE for four drive cycles/profiles. Chemical hydrogen storage models have been developed for the Framework for both exothermic and endothermic materials. Despite the utility of such models, they require that material researchers input system design specifications that cannot be estimated easily. To address this challenge, a design tool has been developed that allows researchers to directly enter kinetic and thermodynamic chemical hydrogen storage material properties into a simple sizing module that then estimates system parameters required to run the storage system model. Additionally, the design tool can be used as a standalone executable file to estimate the storage system mass and volume outside of the Framework model. These models will be explained and exercised with the representative hydrogen storage materials exothermic ammonia borane (NH3BH3) and endothermic alane (AlH3). 相似文献
18.
《International Journal of Hydrogen Energy》2023,48(56):21451-21465
Considering the necessity for compact hydrogen storage system for fuel cell stacks, 41 embedded cooling tube (ECT) reactor with an outer cooling jacket (OCJ) is designed, fabricated and tested with 3.75 kg of LCC1® alloy. To analyse the sensitivity of the system performance at various operating conditions and the applicability of this prototype as storage system, an extensive parametric investigation was carried out at varying supply pressure (Ps), absorption temperature (Ta) and desorption temperature (Td). LCC1® alloy achieved maximum hydrogen storage capacity (HSC) of 1.6 wt% within 420 s at Ps of 25 bar, Ta of 25 °C and heat transfer fluid (HTF) flow rate (HTFa) of 6 LPM. Supply pressure is found to have greater influence than absorption temperature over absorption performance and heating output. With Ta of 25 °C, HTFa of 6 LPM, HSC of 1.58 wt% and 1.6 wt% were achieved at Ps of 20 bar and 30 bar, respectively, resulting in corresponding specific heating power (SHP) of 497.7 W/kg and 544.9 W/kg. Varying Ta from 25 °C to 35 °C at Ps of 20 bar and HTFa of 6 LPM resulted in 3% reduction in HSC. During desorption, desorption temperature of above 20 °C is found to be favourable with more than 95% of stored hydrogen being desorbed. It is further observed that the dehydriding rate of LCC1® was nearly steady which is potentially suitable for fuel cell applications, as the average dehydriding rate is estimated to be about 15.75 NLPM and 22.91 NLPM at Td of 20 °C and 25 °C, respectively, with 6 LPM of HTF flow rate. The analysed module is proposed as a potential hydrogen supply unit for a 1 kW fuel cell reported in literature. 相似文献
19.
《International Journal of Hydrogen Energy》2021,46(62):31699-31726
Thermal management of metal hydride (MH) hydrogen storage systems is critically important to maintain the hydrogen absorption and release rates at desired levels. Implementing thermal management arrangements introduces challenges at system level mostly related to system's overall mass, volume, energy efficiency, complexity and maintenance, long-term durability, and cost. Low effective thermal conductivity (ETC) of the MH bed (~0.1–0.3 W/mK) is a well-known challenge for effective implementation of different thermal management techniques. This paper comprehensively reviews thermal management solutions for the MH hydrogen storage used in fuel cell systems by also focusing on heat transfer enhancement techniques and assessment of heat sources used for this purpose. The literature recommended that the ETC of the MH bed should be greater than 2 W/mK, and heat transfer coefficient with heating/cooling media should be in the range of 1000–1200 W/m2K to achieve desired MH's performance. Furthermore, alternative heat sources such as fuel cell heat recovery or capturing MH heat during charging and releasing it back during discharging have also been thoroughly reviewed here. Finally, this review paper highlights the gaps and suggests directions accordingly for future research on thermal management for MH systems. 相似文献
20.
《International Journal of Hydrogen Energy》2005,30(11):1159-1179
Hydrogen from decentralized water electrolysis is one of the main fuelling options considered for future fuel cell vehicles. In this study, a model is developed to determine the key technical and economic parameters influencing the competitive position of decentralized electrolytic hydrogen. This model incorporates the capital, maintenance and energy costs of water electrolysis, as well as a monetary valuation of the associated greenhouse gas (GHG) emissions. It is used to analyze the competitive position of electrolytic hydrogen in three specific locations with distinct electricity mix: Vancouver, Los Angeles and Paris. Using local electricity prices and fuel taxes, electrolytic hydrogen is found to be commercially viable in Vancouver and Paris. Hydrogen storage comes out as the most important technical issue. But more than any technical issue, electricity prices and fuel taxes emerge as the two dominant issues affecting the competitive position of electrolytic hydrogen. The monetary valuation of GHG emissions, based on a price of $20/ton of CO2, is found to be generally insufficient to tilt the balance in favor of electrolytic hydrogen. 相似文献