Anaerobic treatment of cassava stillage for hydrogen and methane production in continuously stirred tank reactor (CSTR) under high organic loading rate (OLR)

Anaerobic hydrogen and methane production from cassava stillage in continuously stirred tank reactor (CSTR) were investigated in this study. Results showed that the heat-pretreatment of inoculum did not enhance hydrogen yield compared to raw inoculum under mesophilic condition after continuous operation. However, the hydrogen yield increased from about 14 ml H₂/gVS under mesophilic condition to 69.6 ml H₂/gVS under thermophilic condition due to the decrease of propionate concentration and inhibition of homoacetogens. Therefore, temperature was demonstrated to be more important than pretreatment of inoculum to enhance the hydrogen production. Under high organic loading rate (OLR) (>10 gVS/(L·d)), the two-phase thermophilic CSTR for hydrogen and methane production was stable with hydrogen and methane yields of 56.6 mlH₂/gVS and 249 mlCH₄/gVS. The one-phase thermophilic CSTR for methane production failed due to the accumulation of both acetate and propionate, leading to the pH lower than 6. Instead of propionate alone, the accumulations of both acetate and propionate were found to be related to the breakdown of methane reactor.     

Effect of temperature on continuous hydrogen production of cellulose

The effect of temperature on the hydrogen fermentation of cellulose was evaluated by a continuous experiment using a mixed culture without pretreatment. The experiments were conducted at three different temperatures, which were mesophilic [37 ± 2 °C], thermophilic [55 ± 2 °C] and hyper-thermophilic [80 ± 2 °C], with an influent concentration of cellulose of 5 g/l and a hydraulic retention time [HRT] of 10 days. A stable hydrogen production was observed at each condition. At 37 ± 2 °C, the maximum hydrogen yield was 0.6 mmol H₂/g cellulose. However, at 55 ± 2 °C and 80 ± 2 °C, the maximum hydrogen yields were 15.2 and 19.02 mmol H₂/g cellulose, respectively. While 26% of the biogas was methane under the mesophilic temperature, no methane gas was detected under both the thermophilic and hyper-thermophilic temperatures. The results show that operational temperature is a key to sustainable bio-hydrogen production and that the thermophilic and hyper-thermophilic conditions produced better results than mesophilic condition.     

Effect of system optimizing conditions on biohydrogen production from herbal wastewater by slaughterhouse sludge

The study evaluates the biohydrogen production from herbal wastewater as the substrate by the enriched mixed slaughterhouse sludge as the seed source. In the following experiments, batch-fermentations are carried out with the optimum substrate concentrations, fermentation pH and fermentation temperature to observe the effects of H₂ production, hydrogen yield and other fermentation end products at different conditions. The hydrogen production is increased as substrate concentration increased up to 8 g COD/L WW, but drastically decreased at 10 g COD/L WW. When the pH of fermentation is controlled to 6.5, a maximum amount of hydrogen yield could be obtained. The hydrogen production is maximum at 50 °C (930 ± 30 mL/L WW) compared to 30 °C (436 ± 16 mL/L WW). Acid-forming pathway with butyric acid as a major metabolite dominated the metabolic flow during the hydrogen production. The experimental results indicated that effective hydrogen production from the herbal wastewater could be obtained by thermophilic acidogenesis at proper operational conditions.     

Biological saccharification by Clostridium thermocellum and two-stage hydrogen and methane production from hydrogen peroxide-acetic acid pretreated sugarcane bagasse

The present work aimed at establishing an efficient degradation and energy recovery system form sugarcane bagasse (SCB) through hydrogen peroxide-acetic acid (HPAC) pretreatment, thermophilic hydrogen production and mesophilic methane production. The degradation ratio of HPAC pretreated SCB (HPAC-SCB, 2%, w/v) exceeded 90% under the biological hydrolysis of C. thermocellum without enzyme addition. The hydrogen yield in the co-culture fermentation of T. thermosaccharolyticum and C. thermocellum from HPAC-SCB (2%, w/v) reached 226 mL/g substrate. The long-term hydrogen fermentation was successfully established with 1.59 L/(L·d), 0.159 L/g substrate for average hydrogen productivity and yield, respectively. Methane production of 0.341 L/g COD (chemical oxygen demand)_added was recovered by semi-continuous methane fermentation from hydrogen-producing effluent at 12 days of hydraulic retention time (HRT). Average energy recovery of 8.79 MJ/kg SCB was obtained under the optimal conditions. The present work indicated the promising application of the established process in valorization of lignocellulosic bio-waste.     

Enhancement of batch biohydrogen production from prehydrolysate of acid treated oil palm empty fruit bunch

Carbohydrates from hydrolyzed biomass has been a potential feedstock for fermentative hydrogen production. In this study, oil palm empty fruit bunch (OPEFB) was treated by sulfuric acid in different concentrations at 120 °C for 15 min in the autoclave. The optimal condition for pretreatment was obtained when OPEFB was hydrolyzing at 6% (w/v) sulfuric acid concentration, which gave the highest total sugar of 26.89 g/L and 78.51% of sugar production yield. However, the best conversion efficiency of OPEFB pretreatment was 39.47 at sulfuric acid concentration of 4%. A series of batch fermentation were performed to determine the effect of pH in fermentation media and the potential of this prehydrolysate was used as a substrate for fermentative hydrogen production under optimum pretreatment conditions. The prehydrolysate of OPEFB was efficiently converted to hydrogen via fermentation by acclimatized mixed consortia. The maximum hydrogen production was 690 mL H₂ L⁻¹ medium, which corresponded to the yield of 1.98 molH₂/mol_xylose achieved at pH 5.5 with initial total sugar concentration of 5 g/L. Therefore, the results implied that OPEFB prehydrolysate is prospective substrate for efficient fermentative hydrogen conducted at low controlled pH. No methane gas was detected throughout the fermentation.     

Developing a thermophilic hydrogen-producing microbial consortia from geothermal spring for efficient utilization of xylose and glucose mixed substrates and oil palm trunk hydrolysate

Xylose and glucose are the major sugar components of lignocellulosic hydrolysate. This study aims to develop thermophilic hydrogen-producing consortia from eight sediments-rich samples of geothermal springs in Southern Thailand by repeated batch cultivation at 60 °C with glucose, xylose and xylose-glucose mixed substrates. Significant hydrogen production potentials were obtained from thermophilic enriched cultures encoded as PGR and YLT with the maximum hydrogen yields of 241.4 and 231.6 mL H₂/g sugar_consumed, respectively. After repeated batch cultivation the hydrogen yield from xylose-glucose mixed substrate of PGR increased to 375 mL H₂/g sugar_consumed which was 30% higher than that of YLT (287 mL H₂/g sugar_consumed). Soluble metabolites from xylose-glucose mixed substrates were composed mostly of butyric acid (20.6-21.8 mM), acetic acid (7.2-13.5 mM), lactic acid (8.2-11.7 mM) and butanol (4.4-13.0 mM). Denaturing gradient gel electrophoresis (DGGE) profiles illustrated small difference in microbial patterns of PGR enriched with glucose, xylose-glucose mixed substrate and xylose. The dominant populations were affiliated with low G + C content Gram-positive bacteria, Thermoanaerobacterium sp., Thermoanaerobacter sp., Caloramater sp. and Anoxybacillus sp. based on the 16S rRNA gene. Cultivation of the enriched culture PGR in oil palm trunk hydrolysate, the maximum hydrogen yield of 301 mL H₂/g sugar_consumed was achieved at hydrolysate concentration of 40% (v/v). At higher concentration to 80% (v/v), the hydrogen fermentation process was inhibited. Therefore, the efficient thermophilic hydrogen-producing consortia PGR has successfully developed and has great potential for production of biohydrogen from mixed sugars hydrolysate.     

Effects of substrate concentration and hydraulic retention time on hydrogen production from common reed by enriched mixed culture in continuous anaerobic bioreactor

This study aims to investigate the effect of substrate concentration and hydraulic retention time (HRT) on hydrogen production in a continuous anaerobic bioreactor from unhydrolyzed common reed (Phragmites australis) an invasive wetland and perennial grass. The bioreactor has capacity of 1 L and working volume of 600 mL. It was operated at pH 5.5, temperature at 37 °C, hydraulic retention time (HRT) 12 h, and variation of substrate concentration from 40, 50, and 60 g COD/L, respectively. Afterward, the HRT was then varied from 12, 8, to 4 h for checking the optimal biohydrogen production. Each condition was run until reach steady state on hydrogen production rate (HPR) which based on hydrogen percentage and daily volume. The results were obtained the peak of substrate concentration was at the 50 g COD/L with HRT 12 h, average HPR and H₂ concentration were 28.71 mL/L/h and 36.29%, respectively. The hydrogen yield was achieved at 106.23 mL H₂/g CODre. The substrate concentration was controlled at 50 g COD/L for the optimal HRT experiments. It was found that the maximum of average HPR and H₂ concentration were 43.28 mL/L/h and 36.96%, respectively peak at HRT 8 h with the corresponding hydrogen yield of 144.35 mL H₂/g CODre. Finally, this study successful produce hydrogen from unhydrolyzed common reed by enriched mixed culture in continuous anaerobic bioreactor.     

Improvement of hydrogen production with thermophilic mixed culture from rice spent wash of distillery industry

Biohydrogen production processes were investigated using thermophilic bacterial consortia enriched from sludge of the anaerobic digester. A multiple parameter optimization viz. temperature, pH and substrate concentration was performed for maximization of hydrogen production. Heat shock pre-treatment followed by BES (2-bromo ethane sulfonate) treatment was done for the enrichment of hydrogen producing bacteria. Box–Behnken design and response surface methodology were adopted to investigate the mutual interaction among the process parameters. Experimental optimization of process parameters (60 °C, pH 6.5 and 10 g/L) gave the maximum hydrogen production and yield of 3985 mL/L and 2.7 mol/mol glucose respectively in the batch system which is higher than the reported value on UASB. These experimental parameters found concurrent with the values obtained from the theoretical model i.e. 58.4 °C, pH 6.6, 10.8 g/L and yield of 2.71 mol/mol glucose. At optimized conditions, maximum hydrogen production rate (R_m) of 850 mL/h, gas production potential (P) of 4551 mL/L and lag time (λ) of 1.98 h were determined using modified Gompertz equation. Using the optimum conditions, hydrogen production from rice spent wash was conducted in which hydrogen yield of 464 mL/g carbohydrate and hydrogen production rate of 168 mL/L h were obtained. PCR-DGGE profile showed that the thermophilic mixed culture was predominated with species closely affiliated to Thermoanaerobacterium sp.     

Hydrogen production from alcohol wastewater by an anaerobic sequencing batch reactor under thermophilic operation: Nitrogen and phosphorous uptakes and transformation

The objective of this study was to investigate hydrogen production from alcohol wastewater using an anaerobic sequencing batch reactor (ASBR) under thermophilic operation and at a constant pH of 5.5. Under the optimum COD loading rate of 68 kg/m³d, the produced gas contained 43% H₂ without methane and the system provided a hydrogen yield and specific hydrogen production rate of 130 ml H₂/g COD removed and 2100 ml H₂/l d, respectively, which were much higher than those obtained under the mesophilic operation. Under thermophilic operation, both nitrogen and phosphate uptakes were minimal at the optimum COD loading rate for hydrogen production and most nitrogen uptake was derived from organic nitrogen. Under the thermophilic operation for hydrogen production, the nutrient requirement in terms of COD:N:P was found to be 100:6:0.5, which was much higher than that for the methenogenic step for methane production under both thermophilic and mesophilic operations and for the acidogenic step for hydrogen production under mesophilic operation.     

Simultaneous saccharification and fermentation of cellulose for bio-hydrogen production by anaerobic mixed cultures in elephant dung

The objective of this study was to optimize the culture conditions for simultaneous saccharification and fermentation (SSF) of cellulose for bio-hydrogen production by anaerobic mixed cultures in elephant dung under thermophilic temperature. Carboxymethyl cellulose (CMC) was used as the model substrate. The investigated parameters included initial pH, temperature and substrate concentration. The experimental results showed that maximum hydrogen yield (HY) and hydrogen production rate (HPR) of 7.22 ± 0.62 mmol H₂/g CMC_added and 73.4 ± 3.8 mL H₂/L h, respectively, were achieved at an initial pH of 7.0, temperature of 55 °C and CMC concentration of 0.25 g/L. The optimum conditions were then used to produce hydrogen from the cellulose fraction of sugarcane bagasse (SCB) at a concentration of 0.40 g/L (equivalent to 0.25 g/L cellulose) in which an HY of 7.10 ± 3.22 mmol H₂/g cellulose_added. The pre-dominant hydrogen producers analyzed by polymerase chain reaction-denaturing gel gradient electrophoresis (PCR-DGGE) were Thermoanaerobacterium thermosaccharolyticum and Clostridium sp. The lower HY obtained when the cellulose fraction of SCB was used as the substrate might be due to the presence of lignin in the SCB as well as the presence of Lactobacillus parabuchneri and Lactobacillus rhamnosus in the hydrogen fermentation broth.     

Exploring optimal conditions for thermophilic fermentative hydrogen production from cassava stillage

This study investigated the effects of seed sludges, alkalinity and HRT on the thermophilic fermentative hydrogen production from cassava stillage. Five different kinds of sludges were used as inocula without any pretreatment. Though batch experiments showed that mesophilic anaerobic sludge was the best inoculum, the hydrogen yields with different seed sludges were quite similar in continuous experiments in the range of 82.9–92.3 ml H₂/gVS without significant differences which could be attributed to the establishment of Uncultured Thermoanaerobacteriaceae bacterium-dominant microbial communities in all reactors. It is indicated that results obtained from batch experiments are not consistent with those from continuous experiments and all the tested seed sludges are good sources for continuous thermophilic hydrogen production from cassava stillage. The influent alkalinity of 6 g NaHCO₃/L and HRT 24 h were optimal for hydrogen production with hydrogen yield of 76 ml H₂/gVS and hydrogen production rate of 3215 ml H₂/L/d. Butyrate was the predominant metabolite in all experiments. With the increase in alkalinity of more than 6 g/L, the concentration of VFA/ethanol increased while hydrogen yield decreased due to the higher concentration of acetate and propionate. The decrease in HRT resulted in the higher hydrogen production rate but lower hydrogen yield. Variation of hydrogen yields were quite correlated with butyrate/acetate (B/A) ratio with different influent alkalinities, however, butyrate was important parameter to justify the hydrogen yields with various HRTs.     

Hydrogen and methane production in extreme thermophilic conditions in two-stage (upflow anaerobic sludge bed) UASB reactor system

Two-stage hydrogen and methane production in extreme thermophilic (70 °C) conditions was demonstrated for the first time in UASB-reactor system. Inoculum used in hydrogen and methane reactors was granular sludge from mesophilic internal circulation reactor and was first acclimated for extreme thermophilic conditions. In hydrogen reactor, operated with hydraulic retention time (HRT) of 5 h and organic loading rate (OLR) of 25.1 kg COD/m³/d, hydrogen yield was 0.73 mol/mol glucose_added. Methane was produced in second stage from hydrogen reactor effluent. In methane reactor operated with HRT of 13 h and OLR of 7.8 kg COD/m³/d, methane yield was 117.5 ml/g COD_added. These results prove that hydrogen and methane can be produced in extreme thermophilic temperatures, but as batch experiments confirmed, for methane production lower temperature would be more efficient.     

Comparison between heterofermentation and autofermentation in hydrogen production from Arthrospira (Spirulina) platensis wet biomass

Hydrogen production from Arthrospira (Spirulina) platensis wet biomass through heterofermentation by the [FeFe] hydrogenase of hydrogenogens (hydrogen-producing bacteria) and autofermentation by the [NiFe] hydrogenase of Arthrospira platensis was discussed under dark anaerobic conditions. In heterofermentation, wet cyanobacterial biomass without pretreatment was hardly utilized by hydrogenogens for hydrogen production. But the carbohydrates in cyanobacterial cells released after cell wall disruption were effectively utilized by hydrogenogens for hydrogen production. Wet cyanobacterial biomass was pretreated with boiling and bead milling, ultrasonication, and ultrasonication and enzymatic hydrolysis. Wet cyanobacterial biomass pretreated with ultrasonication and enzymatic hydrolysis achieved the maximum reducing sugar yield of 0.407 g/g-DW (83.0% of the theoretical reducing sugar yield). Different concentrations (10 g/l to 40 g/l) of pretreated wet cyanobacterial biomass were used as substrate to produce fermentative hydrogen by hydrogenogens, which were domesticated with the pretreated wet cyanobacterial biomass as carbon source. The maximum hydrogen yield of 92.0 ml H₂/g-DW was obtained at 20 g/l of wet cyanobacterial biomass. The main soluble metabolite products (SMPs) in the residual solutions from heterofermentation were acetate and butyrate. In autofermentation, hydrogen yield decreased from 51.4 ml H₂/g-DW to 11.0 ml H₂/g-DW with increasing substrate concentration from 1 g/l to 20 g/l. The main SMPs in the residual solutions from autofermentation were acetate and ethanol. The hydrogen production peak rate and hydrogen yield at 20 g/l of wet cyanobacterial biomass in heterofermentation showed 110- and 8.4-fold increases, respectively, relative to those in autofementation.     

High efficient biohydrogen production from palm oil mill effluent by two-stage dark fermentation and microbial electrolysis under thermophilic condition

Biohydrogen production from palm oil mill effluent by two-stage dark fermentation and microbial electrolysis was investigated under thermophilic condition. The optimum chemical oxygen demand (COD) concentration and pH for dark fermentation were 66 g·L⁻¹ and 6.5 with a hydrogen yield of 73 mL-H₂·gCOD⁻¹. The dark fermentation effluent consisted of mainly acetate and butyrate. The optimum voltage for microbial electrolysis was 0.7 V with a hydrogen yield of 163 mL-H₂·gCOD⁻¹. The hydrogen yield of continuous two-stage dark fermentation and microbial electrolysis was 236 mL-H₂·gCOD⁻¹ with a hydrogen production rate of 7.81 L·L⁻¹·d⁻¹. The hydrogen yield was 3 times increased when compared with dark fermentation alone. Thermoanaerobacterium sp. was dominated in the dark fermentation stage while Geobacter sp. and Desulfovibrio sp. dominated in the microbial electrolysis cell stage. Two-stage dark fermentation and microbial electrolysis under thermophilic condition is a highly promising option to maximize the conversion of palm oil mill effluent into biohydrogen.     

The effect of hydraulic retention time on thermophilic dark fermentative biohydrogen production in the continuously operated packed bed bioreactor

The main objective of the study is to investigate the effect of hydraulic retention times on continuous dark fermentative biohydrogen production in an up-flow packed bed reactor (UPBR) containing a novel microorganism immobilization material namely polyester fiber beads. The hydrogen producing dark fermentative microorganisms were obtained by heat-pretreatment of anaerobic sludge from the acidogenic phase of an anaerobic wastewater treatment plant. Glucose was the sole carbon source and the initial concentration was 15 ± 1 g/L throughout the continuous feeding. UPBR was operated under the thermophilic condition at T = 48 ± 2 °C and at varying HRTs between 2 h and 6 h. The hydrogen productivity of continuously operated UPBR increased with increasing HRT. Hydrogen production volume varied between 4331 and 6624 ml/d, volumetric hydrogen production rates (VHPR) were obtained as 3.09–4.73 L H₂/L day, and hydrogen production yields (HY) were 0.49 mol/mol glucose-0.89 mol/mol glucose depending on HRT. Maximum daily hydrogen volume (6624 ml/d), the yield (0.89 mol/mol glucose) and VHPR (4.73 L H₂/L day) were obtained at HRT = 6 h. The production rate and the yield decreased with increasing organic loading rate due to substrate inhibition.     

Fermentative bioenergy production from distillers grains using mixed microflora

The feasibility of hydrogen production from distillers grains substrate, an industrial cellulosic waste, was investigated. A substrate concentration of 80 g/L gave the maximum production at 50 °C and pH of 6.0 using sewage sludge. Four controllable factors with three levels: seed sludge (two sewage sludges and cow dung), temperature (40, 50, and 60 °C), pH (6, 7 and 8) and seed pretreatment (none, heat, and acid) were selected in Taguchi experimental design to optimize fermentation conditions. The peak hydrogen and ethanol productions were found with heat-treated cow dung seed, substrate concentration 80 g/L, 50 °C and pH 6. The peak hydrogen production rate and hydrogen yield were 7.9 mmol H₂/L/d and 0.40 mmol H₂/g-COD respectively whereas the peak ethanol production was 3050 mg COD/L and rate 0.22 g EtOH/L/d. A total bioenergy yield of 41 J/g substrate was obtained which was 21% and 79% from hydrogen and ethanol respectively.     

Co-producing hydrogen and methane from higher-concentration of corn stalk by combining hydrogen fermentation and anaerobic digestion

In this paper, the high concentration of corn stalk (60 g/L) was employed as feedstock to produce bio-hydrogen and methane by combining hydrogen fermentation and anaerobic digestion. In the first stage of hydrogen fermentation, the effects of several key parameters, such as strain enhancement technique, cetyl trimethyl ammonium bromide (CTAB), NH₄HCO₃ on hydrogen production from cornstalk were investigated and optimized. The maximum hydrogen yield of 79.8 ± 1.5 ml H₂/g-TS and hydrogen production rate of 3.78 ml/g-cornstalk h was observed at fixed acidizing cornstalk of 60 g/L, strains Bacillus sp. FS2011 dosage of 10%(v/v), CTAB of 30 mg/L, NH₄HCO₃ of 1.2 g/L and initial pH of 7.5 ± 0.5 at 36 ± 1 °C, respectively. In the second stage of anaerobic digestion, the effluent from hydrogen production bio-reactor was further employed as the feedstock to produce methane by methanogenic bacteria, the maximum methane yield of 227 ± 2.5 ml CH₄/g-COD and COD removal rate of 95  ± 1% was recorded. The interesting observations were that the total amount of the organic wastewater produced in a higher substrate concentration (60 g/l) by hydrogen fermentation was reduced by about two-thirds compared with that of traditional low substrate concentration (≤20 g/l).     

Kinetics of cotton cellulose hydrolysis using concentrated acid and fermentative hydrogen production from hydrolysate

The kinetics of cotton cellulose hydrolysis using concentrated sulfuric acid and the performance of fermentative hydrogen production from the hydrolysate in the batch system was carried out in this study. Effects of sulfuric acid concentrations, cotton cellulose concentrations and operating temperatures on the cotton cellulose hydrolysis were investigated. It was found that cotton cellulose can dissolve completely in sulfuric acid concentration above 55% (by volume) at room temperature. The reduced sugar yields were varied from 64.3 to 73.9% (g R-sugar/g cotton cellulose) with the initial cotton cellulose concentrations of 30-70 g/L at a temperature of 40 °C.The reduced sugar concentrations and the initial pH of biohydrogen production were investigated at 37 °C. It was found that the optimal values of the hydrogen yield and substrate utilization were 0.95 mol H₂/mol R-sugar and 98% with an initial pH of 8.2, when substrate concentration was fixed at 20 g R-sugar/L. The maximum hydrogen yield was 0.99 mol H₂/mol R-sugar at a substrate concentration of 15 g R-sugar/L. Using the Gompertz Equation Model simulation, the maximum hydrogen production rate was 253 mL H₂/h/L at a substrate of 30 g/L and initial pH of 8.4.     

Hydrogen and ethanol fermentation of various carbon sources by immobilized Escherichia coli (XL1-Blue)

In this study, hydrogen and ethanol production by a facultative anaerobic bacterium Escherichia coli XL1-Blue immobilized in calcium-alginate beads have been investigated. Batch fermentations were carried out at mesophilic temperature (35 °C) and an initial cultivation pH of 6.5. Firstly, the influence of biomass concentration in terms of dry cell weight (expressed in g DCW/L, range 0.2–1.0) was investigated using fructose (5 g/L) as a carbon source. The peak hydrogen yield (HY) of 1.17 mol-H₂/mol-fructose_utilized was obtained at an initial cell concentration of 0.4 g DCW/L. The hydrogen production potential of other simple carbon sources (glucose and xylose) was evaluated at this optimized cell concentration and peak HY values were attained as 0.96 mol-H₂/mol-glucose_utilized and 0.69 mol-H₂/mol-xylose_utilized, respectively. In addition, utilization of the beverage wastewater (BWW) showed the peak cumulative hydrogen production and ethanol concentration of 120 mL and 5.65 g/L, attained at the substrate concentration of 20 g_{(glucose equivalent)}/L. However, peak HY (1.65 mol-H₂/mol-_{glucose eqivalent utilized}) was observed at low substrate concentration of 5 g_{(glucose equivalent)}/L. The percentage of sugar utilization of BWW was ranged between 80 and 96.     

Production of biohydrogen from waste wheat in continuously operated UPBR: The effect of influent substrate concentration

Utilization of waste materials is one of the most economical approaches to biohydrogen production. Continuous generation of biohydrogen in a bioreactor makes the process more economical with respect to the conventional physical and chemical method. The two main parameters that affect the biohydrogen production in a continuously operated bioreactor are hydraulic retention time (HRT) and influent substrate concentrations. The effect of influent substrate concentration on biohydrogen generation in an up-flow packed bed reactor (UPBR) at HRT = 3 h was investigated in this study. The substrate was waste wheat which was acid hydrolyzed in H₂SO₄ by adjusting the pH value to pH = 2, under high temperature as T = 90 °C in an autoclave to obtain fermentable sugar solution. A natural and porous support particle namely, aquarium biological sponge (ABS) was the microbial immobilization surface in the reactor. Total and hydrogen gas volumes, hydrogen percentage, influent and effluent substrate concentrations, VFA concentrations were monitored. The influent substrate concentration (TS_o) was varied between TS_o = 10 g/L and TS_o = 35 g/L. The process performance was evaluated as biohydrogen volume, percentages, rate and yield under varying operating conditions. The production volume (4275 ml/day) and the rate (3.05 L H₂/L day) were maximum at influent sugar concentration of TS_o = 25 g/L, but the yield reached to its maximum value as Y = 1.22 mol H₂/mol glucose at TS_o = 19 g/L. Substrate limitation and inhibitions were observed at influent concentrations of TS_o = 10 g/L and TS_o = 35 g/L, respectively. The results indicated that ABS could be suggested as a microbial support particle for hydrogen generation in immobilized systems.