Synthesis and hydriding properties of Li2Mg(NH)2

The phase pure Li₂Mg(NH)₂ has been synthesized via a dehydriding treatment of a ball milled 2LiNH₂ + MgH₂ mixture. This phase pure Li₂Mg(NH)₂ has been utilized to investigate its hydriding kinetics at the temperature range 180-220 °C. It is found that the hydriding process of Li₂Mg(NH)₂ is very sluggish even though it has favorable thermodynamic properties for near the ambient temperature operation. Holding at 200 °C for 10 h only results in 3.75 wt.% H₂ uptake. The detailed kinetic analysis reveals that the hydriding process of Li₂Mg(NH)₂ is diffusion-controlled. Thus, this study unambiguously indicates that the future direction to enhance the hydriding kinetics of this promising hydrogen storage material system should be to minimize the diffusion distance and increase the diffusion rate.     

Hydrogen storage behaviour of Li3N doped with Li2O and Na2O

Mixtures of Li₂O/Li₃N and Na₂O/Li₃N have been investigated for hydrogen storage. When Li₃N is doped with ca. 5 mol% Li₂O and annealed, both binary compounds exist as separate phases as evident from powder X-ray diffraction. Li₂O acts as a spectator in the hydrogen storage reactions and there is no evidence of enhanced Li⁺ or H⁺ mobility. Na₂O (5 mol%) interacts more strongly with Li₃N, leading to the generation of an unidentified phase, which also appears to play no part in the hydrogen storage reactions of the composite system. We conclude that addition of these levels of Li₂O or Na₂O to Li₃N followed by annealing does not improve the hydrogen storage properties of Li₃N.     

Destabilization of LiAlH4 by nanocrystalline MgH2

In this work, we report the synthesis, characterization and destabilization of lithium aluminum hydride by ad-mixing nanocrystalline magnesium hydride (e.g. LiAlH₄ + nanoMgH₂). A new nanoparticulate complex hydride mixture (Li–nMg–Al–H) was obtained by solid-state mechano-chemical milling of the parent compounds at ambient temperature. Nanosized MgH₂ is shown to have greater and improved hydrogen performance in terms of storage capacity, kinetics, and initial temperature of decomposition, over the commercial MgH₂. The pressure–composition isotherms (PCI) reveal that the destabilized LiAlH₄ + nanoMgH₂ possess ∼5.0 wt.% H₂ reversible capacity at T ≤ 350 °C. Van't Hoff calculations demonstrate that the destabilized (LiAlH₄ + nanoMgH₂) complex materials have comparable enthalpy of hydrogen release (∼85 kJ/mole H₂) to their pristine counterparts, LiAlH₄ and MgH₂. However, these new destabilized complex hydrides exhibit reversible hydrogen sorption behavior with fast kinetics.     

Investigation of the thermochemical transformations in the LiAlH4-LiNH2 system

The thermal transformations in the lithium alanate-amide system consisting of lithium aluminum hydride (LiAlH₄) and lithium amide (LiNH₂), mixed in a 1:1 M ratio, were investigated using the pressure-composition-temperature analysis, solid-state nuclear magnetic resonance, X-ray powder diffraction, and residual gas analysis. Below 250 °C, the alanate decomposes into Al, LiH and H₂, through the formation of Li₃AlH₆, whereas the amide remains largely intact. The release of gaseous hydrogen corresponds to approximately 5 wt%. Above 250 °C, additional ∼4 wt% of hydrogen is produced through solid-state reactions among LiNH₂, LiH and metallic Al, through the formation of intermetallic Li-Al binary alloy and an unidentified intermediate. The overall reaction of the thermochemical transformation of the LiAlH₄-LiNH₂ mixture results in the production of Li₃AlN₂, metallic Al, LiH and the release of 9 wt% of gaseous hydrogen. The reaction mechanism of the thermal decomposition is different from one identified earlier during mechanical treatment of the same system. Rehydrogenation of the thermally-decomposed products of LiAlH₄-LiNH₂ mixture using high hydrogen pressure (180 bar) and heating (275 °C) yields LiNH₂ and amorphous aluminum nitride (AlN).     

In situ lithiation of TiS2 enabled by spontaneous decomposition of Li3N

We report on a novel method for in situ lithiation of lithium free TiS₂ using Li₃N in an all-solid-state battery configuration. This method was tested using a Li₃N-TiS₂-80Li₂S:20P₂S₅ composite positive electrode and an indium metal negative electrode. It is shown that approximately 37% of Li₃N spontaneously decomposes during composite preparation regardless of the composition. Solid-state battery cells built with a 3:1 stoichiometric ratio of Li:Ti demonstrated a high 1st cycle charge capacity of 287 mAh g⁻¹, 20% greater than the theoretical capacity of TiS₂ at 239 mAh g⁻¹. The difference provides an excess capacity in the indium metal negative electrode.     

Effect of CO on hydrogen storage performance of 2LiNH2 + MgH2 system

(2LiNH₂ + MgH₂) system is one of the most promising hydrogen storage materials due to its suitable operation temperature and high reversible hydrogen storage capacity. In studies and applications, impurities such as CO, CO₂, O₂, N₂ and CH₄ are potential factors which may influence its performance. In the present work, hydrogen containing 1 mol% CO is employed as the hydrogenation gas source, and directly participates in the reaction to investigate the effect of CO on the hydrogen sorption properties of (2LiNH₂ + MgH₂) system. The results indicate that the hydrogen capacity of the (Mg(NH₂)₂ + 2LiH) system declines from 5 wt.% to 3.45 wt.% after 6 cycles of hydrogenation and dehydrogenation, and can not restore to its initial level when use purified hydrogen again. The hydrogen desorption kinetics decreases obviously and the dehydrogenation activation energy increases from 133.35 kJ/mol to 153.35 kJ/mol. The main reason for these is that two new products Li₂CN₂ and MgO appear after (2LiNH₂ + MgH₂) react with CO. They are formed on the surface of materials particles, which may not only cause a permanent loss of NH²⁻, but also prevent the substance transmission during the reaction process. After re-mechanically milling, both kinetics and dehydrogenation activation energy can be recovered to the initial level.     

Mg2FeH6–LiBH4 and Mg2FeH6–LiNH2 composite materials for hydrogen storage

Two composite hydrogen storage materials based on Mg₂FeH₆ were investigated for the first time. The Mg₂FeH₆–LiBH₄ composite of molar ratio 1:5 showed a hydrogen desorption capacity of 5.6 wt.% at 370 °C, and could be rehydrogenated to 3.6 wt.% with the formation of MgH₂, as the material was heated to 445 °C and held at this temperature. The Mg₂FeH₆–LiNH₂ composite of 3:10 molar ratio exhibited a hydrogen desorption capacity of 4.3 wt.% and released hydrogen at 100 °C lower then the Mg₂FeH₆–LiBH₄ composite, but this mixture could not be rehydrogenated. Compared to neat Mg₂FeH₆, both composites show enhanced hydrogen storage properties in terms of desorption kinetics and capacity at these low temperatures. In particular, Mg₂FeH₆–LiNH₂ exhibits a much lower desorption temperature than neat Mg₂FeH₆, but only Mg₂FeH₆–LiBH₄ re-absorbs hydrogen.     

Evaluation of the hydrogen storage behavior of a LiNH2 + MgH2 system with 1:1 ratio

A one-to-one molar ratio of LiNH₂ to MgH₂ was ball milled and characterized to evaluate the proposed hydrogen storage reaction: LiNH₂ + MgH₂ ⇔ LiMgN + 2H₂. The pressure–composition isotherm shows that less than 3.4 wt.% H₂ is released at a plateau pressure near 20 atm at 210 °C. Furthermore, X-ray diffraction show that the products of the reaction include Li₂Mg₂(NH)₃ rather than LiMgN. Combined thermogravimetric and residual gas analyses reveal that large quantities of ammonia are released from the system.     

Synthesis and improved electrochemical performances of porous Li3V2(PO4)3/C spheres as cathode material for lithium-ion batteries

Spherical Li₃V₂(PO₄)₃/C composites are synthesized by a soft chemistry route using hydrazine hydrate as the spheroidizing medium. The electrochemical properties of the materials are investigated by galvanostatic charge-discharge tests, cyclic voltammograms and electrochemical impedance spectrum. The porous Li₃V₂(PO₄)₃/C spheres exhibit better electrochemical performances than the solid ones. The spherical porous Li₃V₂(PO₄)₃/C electrode shows a high discharge capacity of 129.1 and 125.6 mAh g⁻¹ between 3.0 and 4.3 V, and 183.8 and 160.9 mAh g⁻¹ between 3.0 and 4.8 V at 0.2 and 1 C, respectively. Even at a charge-discharge rate of 15 C, this material can still deliver a discharge capacity of 100.5 and 121.5 mAh g⁻¹ in the potential regions of 3.0-4.3 V and 3.0-4.8 V, respectively. The excellent electrochemical performance can be attributed to the porous structure, which can make the lithium ion diffusion and electron transfer more easily across the Li₃V₂(PO₄)₃/electrolyte interfaces, thus resulting in enhanced electrode reaction kinetics and improved electrochemical performance.     

High-rate cathodes based on Li3V2(PO4)3 nanobelts prepared via surfactant-assisted fabrication

In this work, we have synthesized monoclinic Li₃V₂(PO₄)₃ nanobelts via a single-step, solid-state reaction process in a molten hydrocarbon. The as-prepared Li₃V₂(PO₄)₃ nanoparticles have a unique nanobelt shape and are ∼50-nm thick. When cycled in a voltage range between 3.0 V and 4.3 V at a 1C rate, these unique Li₃V₂(PO₄)₃ nanobelts demonstrate a specific discharge capacity of 131 mAh g⁻¹ (which is close to the theoretical capacity of 132 mAh g⁻¹) and stable cycling characteristics.     

The reactions in LiBH4-NaNH2 hydrogen storage system

Stepwise reactions were observed in the ball milling and heating process of the LiBH₄-NaNH₂ system by means of X-ray diffraction (XRD) and Fourier transform infrared spectrometry (FT-IR). During the ball milling process, two concurrent reactions take place in the mixture: 3LiBH₄ + 4NaNH₂ → Li₃Na(NH₂)₄ + 3NaBH₄ and LiBH₄ + NaNH₂ → LiNH₂ + NaBH₄. The heating process from 50 °C to 400 °C is mainly the concurrent reactions of Li₃Na(NH₂)₄ + 3LiBH₄ → 2Li₃BN₂ + NaBH₄ + 8H₂ and 2LiNH₂ + LiBH₄ → Li₃BN₂H₈ → Li₃BN₂ + 4H₂, where the intermediate phases Li₃Na(NH₂)₄ and LiNH₂ serve as the reagents to decompose LiBH₄. The merged equations for the mechanochemical and the heating reactions below 400 °C can be denoted as 3LiBH₄ + 2NaNH₂ → Li₃BN₂ + 2NaBH₄ + 4H₂. The maximum dehydrogenation capacity in closed system below 400 °C is 5.1 wt.% H₂, which agrees well with the theoretical capacity (5.5 wt.% H₂) of the merged equation and thus demonstrates the suggested pathway. The subsequent step consists of the decompositions of NaBH₄ and Li₃Na(NH₂)₄ within the temperature range of 400 °C-600 °C. The apparent activation energies of the two steps are 114.8 and 123.5 kJ/mol, respectively. They are all lower than that of our previously obtained bulk LiBH₄.     

Temperature-controlled microwave solid-state synthesis of Li3V2(PO4)3 as cathode materials for lithium batteries

Monoclinic Li₃V₂(PO₄)₃ can be rapidly synthesized at 750 °C for 5 min (MW5m) by using temperature-controlled microwave solid-state synthesis method (TCMS). The carbon-free sample MW5m presents well electrochemical properties. In the cut-off voltage 3.0-4.3, MW5m presents a charge capacity 132 mAh g⁻¹, almost equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹), and discharge capacity 126.4 mAh g⁻¹. In the cut-off voltage 3.0-4.8 V, MW5m shows an initial discharge capacity of 183.4 mAh g⁻¹, near to the theoretical discharge capacity. In the cycle performance, the capacity fade of Li₃V₂(PO₄)₃ is dependent on the cut-off voltage and the preparation method.     

Synthesis of plate-like Li3V2(PO4)3/C as a cathode material for Li-ion batteries

Plate-like Li₃V₂(PO₄)₃/C composite is synthesized via a solution route followed by solid-state reaction. The Li₃V₂(PO₄)₃/C plates are 40-100 nm in thicknesses and 2-10 μm in lengths. TEM images show that a uniform carbon layer with a thickness of 5.3 nm presents on the surfaces of Li₃V₂(PO₄)₃ plates. The apparent Li-ion diffusion coefficient of the plate-like Li₃V₂(PO₄)₃/C is calculated to be 2.7 × 10⁻⁸ cm² s⁻¹. At a charge-discharge rate of 3 C, the plate-like Li₃V₂(PO₄)₃/C exhibits an initial discharge capacity of 125.2 and 133.1 mAh g⁻¹ in the voltage ranges of 3.0-4.3 and 3.0-4.8 V, respectively. After 500 cycles, the electrodes still can deliver a discharge capacity of 111.8 and 97.8 mAh g⁻¹ correspondingly, showing a good cycling stability.     

Enhancement of the H2 desorption properties of LiAlH4 doping with NiCo2O4 nanorods

Lithium aluminum hydride (LiAlH₄) is considered as an attractive candidate for hydrogen storage owing to its favorable thermodynamics and high hydrogen storage capacity. However, its reaction kinetics and thermodynamics have to be improved for the practical application. In our present work, we have systematically investigated the effect of NiCo₂O₄ (NCO) additive on the dehydrogenation properties and microstructure refinement in LiAlH₄. The dehydrogenation kinetics of LiAlH₄ can be significantly increased with the increase of NiCo₂O₄ content and dehydrogenation temperature. The 2 mol% NiCo₂O₄-doped LiAlH₄ (2% NCO–LiAlH₄) exhibits the superior dehydrogenation performances, which releases 4.95 wt% H₂ at 130 °C and 6.47 wt% H₂ at 150 °C within 150 min. In contrast, the undoped LiAlH₄ sample just releases <1 wt% H₂ after 150 min. About 3.7 wt.% of hydrogen can be released from 2% NCO–LiAlH₄ at 90 °C, where total 7.10 wt% of hydrogen is released at 150 °C. Moreover, 2% NCO–LiAlH₄ displayed remarkably reduced activation energy for the dehydrogenation of LiAlH₄.     

Enhanced hydrogen storage properties of 4MgH2 + LiAlH4 composite system by doping with Fe2O3 nanopowder

In this paper, the hydrogen storage properties and reaction mechanism of the 4MgH₂ + LiAlH₄ composite system with the addition of Fe₂O₃ nanopowder were investigated. Temperature-programmed-desorption results show that the addition of 5 wt.% Fe₂O₃ to the 4MgH₂ + LiAlH₄ composite system improves the onset desorption temperature to 95 °C and 270 °C for the first two dehydrogenation stage, which is lower 40 °C and 10 °C than the undoped composite. The dehydrogenation and rehydrogenation kinetics of 5 wt.% Fe₂O₃-doped 4MgH₂ + LiAlH₄ composite were also improved significantly as compared to the undoped composite. Differential scanning calorimetry measurements indicate that the enthalpy change in the 4MgH₂–LiAlH₄ composite system was unaffected by the addition of Fe₂O₃ nanopowder. The Kissinger analysis demonstrated that the apparent activation energy of the 4MgH₂ + LiAlH₄ composite (125.6 kJ/mol) was reduced to 117.1 kJ/mol after doping with 5 wt.% Fe₂O₃. Meanwhile, the X-ray diffraction analysis shows the formation of a new phase of Li₂Fe₃O₄ in the doped composite after the dehydrogenation and rehydrogenation process. It is believed that Li₂Fe₃O₄ acts as an actual catalyst in the 4MgH₂ + LiAlH₄ + 5 wt.% Fe₂O₃ composite which may promote the interaction of MgH₂ and LiAlH₄ and thus accelerate the hydrogen sorption performance of the MgH₂ + LiAlH₄ composite system.     

Influence of multiple oxide (Cr2O3/Nb2O5) addition on the sorption kinetics of MgH2

The influence of multiple additions of two oxides, Cr₂O₃ and Nb₂O₅, as additives on the hydrogen sorption kinetics of MgH₂ after milling was investigated. We found that the desorption kinetics of MgH₂ were improved more by multiple oxide addition than by single addition. Even for the milled MgH₂ micrometric size powders, the high hydrogen capacity with fast kinetics were achieved for the powders after addition of 0.2 mol% Cr₂O₃ + 1 mol% Nb₂O₅. For this composition, the hydride desorbed about 5 wt.% hydrogen within 20 min and absorbed about 6 wt.% in 5 min at 300 °C. Furthermore, the desorption temperature was decreased by 100 °C, compared to MgH₂ without any oxide addition, and the activation energy for the hydrogen desorption was estimated to be about 185 kJ mol⁻¹, while that for MgH₂ without oxide was about 206 kJ mol⁻¹.     

Effects of Fe2P and Li3PO4 additives on the cycling performance of LiFePO4/C composite cathode materials

In this study, a solution method was employed to synthesize LiFePO₄-based powders with Li₃PO₄ and Fe₂P additives. The composition, crystalline structure, and morphology of the synthesized powders were investigated by using ICP-OES, XRD, TEM, and SEM, respectively. The electrochemical properties of the powders were investigated with cyclic voltammetric and capacity retention studies. The capacity retention studies were carried out with LiFePO₄/Li cells and LiFePO₄/MCMB cells comprised LiFePO₄-based materials prepared at various temperatures from a stoichiometric precursor. Among all of the synthesized powders, the samples synthesized at 750 and 775 °C demonstrate the most promising cycling performance with C/10, C/5, C/2, and 1C rates. The sample synthesized at 775 °C shows initial discharge capacity of 155 mAh g⁻¹ at 30 °C with C/10 rate. From the results of the cycling performance of LiFePO₄/MCMB cells, it is found that 800 °C sample exhibited higher polarization growth rate than 700 °C sample, though it shows lower capacity fading rate than 700 °C sample. For Fe₂P containing samples, the diffusion coefficient of Li⁺ ion increases with increasing amount of Fe₂P, however, the sample synthesized at 900 °C shows much lower Li⁺ ion diffusion coefficient due to the hindrance of Fe₂P layer on the surface of LiFePO₄ particles.     

Effect of gas back pressure on hydrogen storage properties and crystal structures of Li2Mg(NH)2

The ternary imide Li₂Mg(NH)₂ is considered to be one of the most promising on-board hydrogen storage materials due to its high reversible hydrogen capacity of 5.86 wt%, favorable thermodynamic properties and good cycling stability. In this work, Li₂Mg(NH)₂ was synthesized by dynamically dehydrogenating a mixture of Mg(NH₂)₂–2LiH up to 280 °C under different gas (Ar and H₂) and pressures (0–9.0 bar). The crystal structure of Li₂Mg(NH)₂ was found to depend on the gas back pressure in the dehydrogenation process. The crystal structure of Li₂Mg(NH)₂ and the dehydrogenation/rehydrogenation properties of the Mg(NH₂)₂–2LiH system strongly depend on the gas back pressure in the dehydrogenation process due to the effect of the pressure on the dehydrogenation kinetics. This study provides a new approach for improving the hydrogen storage properties of the amide–hydride systems.     

Synthesis and characterization of Li3V(2 − 2x/3)Mgx(PO4)3/C cathode material for lithium-ion batteries

Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C (x = 0, 0.15, 0.30, 0.45) composites have been synthesized by the sol-gel assisted solid state method, using adipic acid C₆H₁₀O₄ (hexanedioic acid) as carbon source. The particle size of the composites is ∼1 μm. During the pyrolysis process, Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C network structure is formed. The effect of Mg²⁺ doped on the electrochemical properties of Li₃V₂(PO₄)₃/C positive materials has been studied. Li₃V_1.8Mg_0.30(PO₄)₃/C as the cathode materials of Li-ion batteries, the retention rate of discharge capacity is 91.4% (1 C) after 100 cycles. Compared with Li₃V₂(PO₄)₃/C, Li₃V_{(2 − 2x/3)}Mg_x(PO₄)₃/C composites have shown enhanced capacity and retention rate capability. The long-term cycles and ex situ XRD tests disclose that Li₃V_1.8Mg_0.30(PO₄)₃ exhibits higher structural stability than the undoped system.     

Synthesis and dehydrogenation of LiCa(NH2)3(BH3)2

We report the synthesis of a new hydrogen storage material with a composition of LiCa(NH₂)₃(BH₃)₂. The theoretical hydrogen capacity of LiCa(NH₂)₃(BH₃)₂ is 9.85 wt.%. It can be prepared by ball milling the mixture of calcium amidoborane (Ca(NH₂BH₃)₂) and lithium amide (LiNH₂) in a molar ratio of 1:1. The experimental results show that this material starts to release hydrogen at a temperature as low as ca. 50 °C, which is ca. 70 °C lower than that of pure Ca(NH₂BH₃)₂ possibly resulting from the active interaction of NH₂⁻ in LiNH₂ with BH₃ in Ca(NH₂BH₃)₂. ca. 4.1 equiv. or 6.8 wt.% hydrogen can be released at 300 °C. The dehydrogenation is a mildly exothermic process forming stable nitride products.