Optimization of cryogenic cooled EDM process parameters using grey relational analysis

This paper presents an experimental investigation on cryogenic cooling of liquid nitrogen (LN₂) copper electrode in the electrical discharge machining (EDM) process. The optimization of the EDM process parameters, such as the electrode environment (conventional electrode and cryogenically cooled electrode in EDM), discharge current, pulse on time, gap voltage on material removal rate, electrode wear, and surface roughness on machining of AlSiCp metal matrix composite using multiple performance characteristics on grey relational analysis was investigated. The L₁₈ orthogonal array was utilized to examine the process parameters, and the optimal levels of the process parameters were identified through grey relational analysis. Experimental data were analyzed through analysis of variance. Scanning electron microscopy analysis was conducted to study the characteristics of the machined surface.     

Experimental Investigation on Electrical Discharge Drilling of Ti-6Al-4V Alloy

This article describes the experimental investigation related to creation of holes in aerospace titanium alloy workpiece using static electrode machining and electrical discharge drilling (EDD) process. Special attachment for holding and rotating the tool electrode was developed and installed on electrical discharge machining (EDM) machine by replacing the original conventional tool holder provided on die sinking EDM. The effect of input parameters such as gap current, pulse on-time, duty factor and RPM of tool electrode on output parameters for average hole circularity (C_a) and average surface roughness (R_a) have been studied. It is observed that the effect of rotating electrode machining has considerable influence on the output parameters over stationary electrode machining. The micro-graphs and photographs of few selected samples were taken by SEM and metallurgical microscope, which also commensurate with the findings of the study.     

Experimental research on electrical discharge machining characteristics of engineering ceramics with different electrical resistivities

Electrical discharge machining (EDM) is the extensively used nonconventional material removal process for machining engineering ceramics provided they are electrically conductive. However, the electrical resistivity of the popular engineering ceramics is higher, and there has been no research on the relationship between the EDM parameters and the electrical resistivity of the engineering ceramics that can be machined effectively by EDM. This paper investigates the effects of the electrical resistivity and the EDM parameters on the EDM performance of ZnO/Al₂O₃ ceramic in terms of the machining efficiency and the quality. The experimental results showed that the electrical resistivity and the EDM parameters such as pulse on-time, pulse off-time, and peak current had the great influence on the machining efficiency and the quality during electrical discharge machining of ZnO/Al₂O₃ ceramic. Moreover, the electrical resistivity of the ZnO/Al₂O₃ ceramic, which could be effectively machined by EDM, increased with increasing the pulse on-time and peak current and with decreasing the pulse off-time, respectively. Furthermore, the ZnO/Al₂O₃ ceramic with the electrical resistivity up to 3,410 Ω cm could be effectively machined by EDM with the appropriate machining condition.     

Research on the influence of dielectric characteristics on the EDM of titanium alloy

This study investigated the influences of dielectric characteristics, namely, electrical conductivity, oxidability, and viscosity on the electrical discharge machining (EDM) of titanium alloy. A new kind of compound dielectric with optimal processing effect was developed based on the identified effects. Comparative experiments on titanium alloy EDM in compound dielectric, distilled water, and kerosene were performed to analyze the difference in material removal rate (MRR), relative electrode wear ratio (REWR), and surface roughness (SR). The experimental results revealed that titanium alloy EDM in compound dielectric achieved the highest MRR, a lower REWR than that in kerosene, and better SR and fewer micro-cracks than that in distilled water.     

Modeling and analysis of the effects of machining parameters on the performance characteristics in the EDM process of Al2O3+TiC mixed ceramic

Electric discharge machining (EDM) has achieved remarkable success in the manufacture of conductive ceramic materials for the modern metal industry. Mathematical models are proposed for the modeling and analysis of the effects of machining parameters on the performance characteristics in the EDM process of Al₂O₃+TiC mixed ceramic which are developed using the response surface methodology (RSM) to explain the influences of four machining parameters (the discharge current, pulse on time, duty factor and open discharge voltage) on the performance characteristics of the material removal rate (MRR), electrode wear ratio (EWR), and surface roughness (SR). The experiment plan adopts the centered central composite design (CCD). The separable influence of individual machining parameters and the interaction between these parameters are also investigated by using analysis of variance (ANOVA). This study highlights the development of mathematical models for investigating the influences of machining parameters on performance characteristics and the proposed mathematical models in this study have proven to fit and predict values of performance characteristics close to those readings recorded experimentally with a 95% confidence interval. Results show that the main two significant factors on the value of the material removal rate (MRR) are the discharge current and the duty factor. The discharge current and the pulse on time also have statistical significance on both the value of the electrode wear ratio (EWR) and the surface roughness (SR).     

Development and application of new composite materials as EDM electrodes manufactured via selective laser sintering

The cost of a part manufactured by electrical dischargeEDM machining (EDM) is mainly determined by electrode cost. The production of electrodes by conventional machining processes is complex, time consuming, and can account for over 50 % of the total EDM process costs. The emerging additive manufacturing (AM) technologies provide the possibility of direct fabrication of EDM electrodes. Selective laser sintering (SLS) is an alternative AM technique because it has the possibility to directly produce functional components, reducing the tool-room lead time and total EDM costs. The main difficulty of manufacturing an EDM electrode using SLS is the selection of an appropriate material, once both processes require different material properties. The current work focused on the investigation of appropriate materials that fulfill EDM and SLS process demands. Three new metal-matrix materials composed of Mo–CuNi, TiB₂–CuNi, and ZrB₂–CuNi were developed and characterized. Electrodes under adequate SLS conditions were manufactured through a systematic methodology. EDM experiments using different discharge energies were carried out, and the performance evaluated in terms of material removal rate and volumetric relative wear. The results showed that the powder systems composed of Mo–CuNi, TiB₂–CuNi, and ZrB₂–CuNi revealed to be successfully processed by SLS, and the EDM experiments demonstrated that the new composite electrodes are promising materials. The work also suggests important topics for future research work on this field.     

A review on the use of dielectric fluids and their effects in electrical discharge machining characteristics

Electrical discharge machining (EDM) is one of the earliest non-traditional machining processes. EDM process is based on thermoelectric energy between the work piece and an electrode. In electrical discharge machining (EDM), a process utilizing the removal phenomenon of electrical discharge in dielectric, the working fluid plays an important role affecting the material removal rate and the properties of the machined surface. Choosing the right dielectric fluid is critical for successful operations. This paper presents a literature survey on the use of dielectric fluids and also their effects in electrical discharge machining characteristics.     

Surface Improvement Using a Combination of Electrical Discharge Machining with Ball Burnish Machining Based on the Taguchi Method

This study investigates the feasibility of improving surface integrity via a novel combined process of electrical discharge machining (EDM) with ball burnish machining (BBM) using the Taguchi method. To provide burnishing immediately after the EDM process, ZrO₂ balls were attached to the tool electrode in the experiments. To verify the optimal process, three observed values, i.e. material removal rate, surface roughness, and improvement ratio of surface roughness were chosen. In addition, six independent parameters were adopted for evalu-ation by the Taguchi method. From the ANOVA and S/N ratio response graph, the significant parameters and the optimal combination level of machining parameters were obtained. Experimental results indicate that the combined process effectively improves the surface roughness and eliminates the micro pores and cracks caused by EDM. Therefore, the combination of EDM and BBM is a feasible process by which to obtain a fine-finishing surface and achieve surface modification.     

Micro electrical discharge machining using high electric resistance electrodes

In micro electrical discharge machining (EDM), because the material removal per single pulse discharge mainly determines the minimum machinable size of a micro EDM, decreasing the material removal per single pulse discharge is important. In this study, in order to decrease the material removal per single pulse discharge, high electric resistance materials such as single-crystal silicon are used for electrodes. Analytical results show that when the electrode resistance increases, the peak value of the discharge current decreases, whereas the pulse duration increases. In addition, the discharge energy decreases when increasing the resistance. Silicon is used as a tool electrode, and the effect of resistivity of the silicon tool electrode on the diameter of discharge craters generated on the stainless steel workpiece is examined. Experimental results reveal that with increasing silicon electrode resistivity, the diameter of discharge craters decreases. Because the diameter of discharge craters can be decreased to 0.5 μm, improved finished surfaces of R_z 0.03 μm are obtained.     

A study of die helical thread cavity surface finish made by Cu-W electrodes with planetary EDM

An experimental research study intended for the application of a planetary electrical discharge machining (EDM) process with copper-tungsten (Cu-W) electrodes in the surface micro-finishing of die helical thread cavities made with AISI H13 tool steel full-hardened at 53 HRC is presented. To establish the EDM parameters’ effect on various surface finishing aspects and metallurgical transformations, three tool electrode Cu-W compositions are selected, and operating parameters such as the open-circuit voltage (U ₀), the discharge voltage (u _e), the peak discharge current (î _e), the pulse-on duration (t _i), the duty factor (τ) and the dielectric flushing pressure (p _in), are correlated. The researched machining characteristics are the material removal rate (MRR—V _w), the relative tool wear ratio (TWR—?), the workpiece surface roughness (SR—Ra), the average white layer thickness (WLT—e _wl) and the heat-affected zone (HAZ—Z _ha). An empirical relation between the surface roughness (SR—Ra) and the energy per discharge (W _e) has been determined. It is analysed that copper-tungsten electrodes with negative polarity are appropriate for planetary EDM die steel surface micro-finishing, allowing the attaining of good geometry accuracy and sharp details. For die steel precision EDM, the relative wear ratio optimum condition and minor surface roughness takes place at a gap voltage of 280 V, discharge current of 0.5–1.0 A, pulse-on duration of 0.8 μs, duty factor of 50%, dielectric flushing pressure of 40 kPa and copper tungsten (Cu20W80) as the tool electrode material with negative polarity. The copper-tungsten electrode’s low material removal rate and low tool-wear ratio allows the machining of EDM cavity surfaces with an accurate geometry and a “mirror-like” surface micro-finishing. A planetary EDM application to manufacture helical thread cavities in steel dies for polymer injection is presented. Conclusions are appointed for the planetary EDM of helical thread cavities with Cu-W electrodes validating the accomplishment as a novel technique for manufacturing processes.     

Simultaneous optimisation of multiple performance characteristics in micro-EDM drilling of titanium alloy

Micro-electrical discharge machining (micro-EDM) has become a widely accepted non-traditional material removal process for machining conductive and difficult-to-cut materials effectively and economically. Being a difficult-to-cut material, titanium alloy suffers poor machinability for most cutting processes, especially the drilling of micro-holes using traditional machining methods. Although EDM is suitable for machining titanium alloys, selection of machining parameters for higher machining rate and accuracy is a challenging task in machining micro-holes. In this study, an attempt has been made for simultaneous optimization of the process performances like, metal removal rate, tool wear rate and overcut based on Taguchi methodology. Thus, the optimal micro-EDM process parameter settings have been found out for a set of desired performances. The process parameters considered in the study were pulse-on time, frequency, voltage and current while tungsten carbide electrode was used as a tool. Verification experiments have been carried out and the results have been provided to illustrate the effectiveness of this approach.     

Optimization of machining parameters using magnetic-force-assisted EDM based on gray relational analysis

This work developed a novel process of magnetic-force-assisted electrical discharge machining (EDM) and conducted an experimental investigation to optimize the machining parameters associated with multiple performance characteristics using gray relational analysis. The main machining parameters such as machining polarity (P), peak current (I _P), pulse duration (τ _P), high-voltage auxiliary current (I _H), no-load voltage (V), and servo reference voltage (S _V) were selected to explore the effects of multiple performance characteristics on the material removal rate, electrode wear rate, and surface roughness. The experiments were conducted according to an orthogonal array L18 based on Taguchi method, and the significant process parameters that affected the multiple performance characteristics of magnetic-force-assisted EDM were also determined form the analysis of variance. Moreover, the optimal combination levels of machining parameters were also determined from the response graph and then verified experimentally. The multiple performance characteristics of the magnetic-force-assisted EDM were improved, and the EDM technique with high efficiency, high precision, and high-quality surface were established to meet the demand of modern industrial applications.     

High efficiency fine boring of monocrystalline silicon ingot by electrical discharge machining

This article deals with high efficiency and high accuracy fine boring in a monocrystalline silicon ingot by electrical discharge machining (EDM). In manufacturing process of integrated circuits, a plasma-etching process is used for removing oxidation films. This process has recently been examined for use of monocrystalline silicon as the electrode to minimize the contamination. However, it is difficult to machine silicon accurately by the conventional diamond drilling method, because the material removal is due to brittle fracture. The machining force in the EDM process is very small compared with that in conventional machining, therefore, the possibility of high efficiency and high accuracy boring holes in silicon ingot by EDM is experimentally investigated. The removal rate of monocrystalline silicon by EDM is much higher than that of steel, while the electrode wear is extremely small. The improvement method leads to a better hole without chipping at the exit of hole or sticking of the insulator on the wall of hole. Furthermore, it is proved that even a high aspect ratio of about 200 boring is possible.     

铝基碳化硅异形电极电火花加工技术研究

为了改善电火花深小孔加工过程中,因加工碎屑排出不畅而导致的加工速度慢、电极损耗严重等问题,制备螺旋、三沟槽和削边三种形貌的异形结构电极。在相同的加工条件下,以铝基碳化硅为实验材料,采用异形结构电极与圆柱电极分别进行不同深度下深小孔加工实验,对加工效率、电极损耗和深小孔内表面形貌三方面进行对比分析。实验结果表明:异形结构电极在深小孔的加工效率和电极损耗方面都优于圆柱电极;小孔内表面形貌方面:圆柱电极加工后的孔内表面附着碎屑较多。     

Analysis of the machining characteristics of EDM as functions of the mobilities of electrons and ions

Electrical discharge machining (EDM) is a process that can be used effectively to machine conductive metals regardless of their hardness. In the EDM process, material removal occurs because of the thermal energy of the plasma channel between the electrode and the workpiece. During EDM, the electrode as well as the workpiece is abraded by the thermal energy. Tool wear adversely affects the machining accuracy and increases tooling costs. Many previous studies have focused on mitigating the problems of tool wear by investigating various EDM parameters. In this study, the tool wear problem was investigated on the basis of the mobilities of electrons and ions in the plasma channel. The material removal volumes of both the electrode and the workpiece were compared as functions of the gap voltage. The material removal difference according to the capacitance was also investigated. The tool wear ratio was calculated under different EDM condition and an EDM conditions for reducing the tool wear ratio was suggested.     

Optimisation of process parameters for multi-performance characteristics in EDM of Al2O3 ceramic composite

The advantages of electrical discharge machining (EDM) in machining of complex ceramic components have promoted research in the area of EDM of ceramic composites. The recent developments in ceramic composites are focused not only on the improvements of strength and toughness, but also on possibilities for difficult-to-machine shapes using EDM. One such EDM-machinable ceramic composite material (Al₂O₃–SiC_w–TiC) has been developed recently and has been selected in the present study to investigate its EDM machinability. Experiments were conducted using discharge current, pulse-on time, duty cycle and gap voltage as typical process parameters. The grey relational analysis was adopted to obtain grey relational grade for EDM process with multiple characteristics namely material removal rate and surface roughness. Analysis of variance was used to study the significance of process variables on grey relational grade which showed discharge current and duty cycle to be most significant parameters. Other than discharge current and duty cycle, pulse-on time and gap voltage have also been found to be significant. To validate the study, confirmation experiment has been carried out at optimum set of parameters and predicted results have been found to be in good agreement with experimental findings.     

Study on the characteristics of plasma channel based on multi-spark pulse discharge machining effect

Plasma channel characteristics and energy distribution in electrical discharge machining (EDM) were mostly studied by analyzing the geometry parameters of craters caused by a single pulse discharge in previous studies. However, single pulse experiments cannot provide us insights into superposition, migration, abruption, interruption, and other phenomena of the plasma channel which have significant effects on EDM. Besides, EDM itself is a consecutive pulse discharge process. Thus, this paper focuses on the characteristics of plasma channel and the mechanism of material removal based on experimental data from multi-spark pulse discharge machining. The contrastive milling experiments of different parameters in multi-spark pulse discharge machining in high-speed dry EDM by using nickel-based superalloy as workpiece were conducted. The effects of peak current, dielectric type, breakdown voltage, air pressure, and electrode rotation speed on the crater number, crater distance, crater depth, and crater removal volume were studied. The plasma channel characteristics and material removal mechanism in continuous machining of high-speed dry EDM were revealed.     

MICRO ELECTRICAL DISCHARGE MACHINING DEPOSITION IN AIR

A new deposition method is described using micro electrical discharge machining (EDM) to deposit tool electrode material on workpiece in air. The basic principles of micro electrical discharge deposition (EDD) are analyzed and the realized conditions are predicted. With an ordinary EDM shaping machine, brass as the electrode, high-speed steel as the workpiece, a lot of experiments are carried out on micro EDD systematically and thoroughly. The effects of major processing parameters, such as the discharge current, discharge duration, pulse interval and working medium, are obtained. As a result, a micro cylinder with 0.19 mm in diameter and 7.35 mm in height is deposited. By exchanging the polarities of the electrode and workpiece the micro cylinder can be removed selectively. So the reversible machining of deposition and removal is achieved, which breaks through the constraint of traditional EDM. Measurements show that the deposited material is compact and close to workpiece base, whose components depend on the tool electrode material.     

Investigation of emulsion for die sinking EDM

Machining fluid is a primary factor that affects the material removal rate, surface quality, and electrode wear of electrical discharge machining (EDM). Kerosene is the most commonly used working fluid in die sinking EDM, but it shows low ignition temperature and high volatility; if the improper operations are undertaken, it can cause conflagration. Using distilled water or pure water as the machining fluid in EDM, no fire hazard occurs, and the working environment is well; however, using distilled water or pure water as the machining fluid in EDM, the material removal rate of machining large surface is low, and the machine tool is easily eroded. Emulsion-1 and emulsion-2 used as working fluid in die sinking EDM are developed. The compositions of emulsion-1 and emulsion-2 are introduced. In comparison with kerosene, emulsion-1 and emulsion-2 used in EDM show high material removal rate, low surface roughness, high discharge gap, and good working environment. The electrode wear ratio in emulsion-1 is lower than that in kerosene. The electrode wear ratio in emulsion-2 is higher than that in kerosene. The effects of composition and concentration of emulsifier on the emulsion property and EDM performance have been investigated. The comparative tests of EDM performance with kerosene, emulsion-1, and emulsion-2 have been done.     

4Cr5MoVSi电火花加工试验特征规律研究

采用紫铜工具电极,在峰值电流为4-24A、脉冲宽度为25-200μs、加工电压为80-200V的电参数范围内,综合应用因子试验和正交试验方法,对难加工材料4Cr5MoVSi进行了电火花加工试验。在进行电加工基础特征规律分析的基础上,考查了电参数对加工速度、双边侧面放电间隙、电极损耗的影响,并对电火花加工机理进行了分析。研究结果表明:采用紫铜电极电火花加工4Cr5MoVSi,在本试验范围内,峰值电流Ip与脉冲宽度ti、加工电压U、脉冲间隔t0存在一定的交互作用;与其它三个因素相比,峰值电流对加工速度、电极损耗、双边侧面放电间隙的影响更显著;随脉冲宽度和加工电压的增大,电极损耗逐渐减小。