Electrochemical properties of Li ion polymer battery with gel polymer electrolyte based on polyurethane

Gel polymer electrolyte (GPE) was prepared using polyurethane acrylate as polymer host and its performance was evaluated. LiCoO₂/GPE/graphite cells were prepared and their electrochemical performance as a function of discharge currents and temperatures was evaluated. The precursor containing a 5 vol % curable mixture had a viscosity of 4.5 mPa s. The ionic conductivity of the GPE at 20 °C was about 4.5 × 10^–3 S cm^–1. The GPE was stable electrochemically up to a potential of 4.8 V vs Li/Li⁺. LiCoO₂/GPE/graphite cells showed a good high rate and low-temperature performance. The discharge capacity of the cell was stable with charge–discharge cycling.     

Poly(methylmethacrylate)—magnesium triflate gel polymer electrolyte for solid state magnesium battery application

A gel polymer electrolyte (GPE) film of poly(methylmethacrylate) and magnesium triflate is studied in view of its potential application in a solid state rechargeable magnesium battery. Experimental data of a.c. impedance and cyclic voltammetric studies of symmetrical cells made of blocking and non-blocking electrodes, and also data of charge/discharge cycles of Mg/GPE/MnO₂ cells are reported. The composition of the GPE is optimized in view of a minimum quantity of the liquid components (propylene carbonate and ethylene carbonate) required for the gel formation and a maximum conductivity. Specific conductivity (σ) of the GPE of optimum composition is (4.2±0.45)×10⁻⁴ S cm⁻¹ at 20 °C. The σ values follow the Arrhenius equation and the activation energy for GPE of optimum composition is 0.038 eV. The effects of temperature and ageing on Mg/GPE interface are studied. Discharge capacity of about 90 mAh g⁻¹ of MnO₂ is obtained during the discharge of Mg/GPE/MnO₂ cells. On repeated charge/discharge cycling of the cell, the discharge capacity decreases to about 70 mAh g⁻¹. The cycle-life is limited by the problems associated with passivation of the Mg surface.     

Improvement of electrochemical properties of LiNi0.5Mn1.5O4 spinel prepared by radiated polymer gel method

LiNi_0.5Mn_1.5O₄ as a 4.7 V-class cathode material was prepared through the radiated polymer gel method that allowed homogeneous mixing of starting materials at the atomic scale. After calcinations of the polymer gels containing the metal salts at different temperatures from 750 to 1150 °C, powders of a pure LiNi_0.5Mn_1.5O₄ phase were obtained. X-ray diffraction and transmission electron microscopy were used to characterize the structures of the powders. Galvanostatic cell cycling and a simultaneous DC resistance measurement were performed on Li/LiNi_0.5Mn_1.5O₄ cells. It is found that the powder calcined at 950 °C shows the best electrochemical performance with the initial discharge capacity of 139 mAh g⁻¹ and 96% retention after 50 cycles. Adopting a slow cooling procedure for the powder calcination can increase the capacity of LiNi_0.5Mn_1.5O₄ at the 4.7 V plateau. Besides, a “w”-shape change of the DC resistance of Li/LiNi_0.5Mn_1.5O₄ cells is a good indication of the structural change of LiNi_0.5Mn_1.5O₄ electrode during charge and discharge courses.     

Highly ion-conductive solid polymer electrolytes based on polyethylene non-woven matrix

Highly ion-conductive solid polymer electrolyte (SPE) based on polyethylene (PE) non-woven matrix is prepared by filling poly(ethylene glycol) (PEG)-based crosslinked electrolyte inside the pores of the non-woven matrix. The PE non-woven matrix not only shows good mechanical strength for SPE to be a free-standing film, but also has very porous structure for high ion conductivity. The ion conductivity of SPE based on PE non-woven matrix can be enhanced by adding sufficient non-volatile plasticizer such as poly(ethylene glycol) dimethyl ether (PEGDME) into ion conduction phase without sacrificing mechanical strength. SPE with 20 wt.% crosslinking agent and 80 wt.% non-volatile plasticizer shows 3.1 × 10⁻⁴ S cm⁻¹ at room temperature (20 °C), to our knowledge, which is the highest level for SPEs. It is also electrochemically stable up to 5.2 V and has high transference number about 0.52 due to the introduction of anion receptor as an additive. The interfacial resistance between Li electrode and SPE is low enough to perform charge/discharge test of unit cell consisting of LiCoO₂/SPE/Li at room temperature. The discharge capacity of the unit cell shows 87% of theoretical value with 86% Coulombic efficiency.     

Synthesis and electrochemical characterization of PEO-based polymer electrolytes with room temperature ionic liquids

New gel polymer electrolytes containing 1-butyl-4-methylpyridinium bis(trifluoromethanesulfonyl)imide (BMPyTFSI) ionic liquid are prepared by solution casting method. Thermal and electrochemical properties have been determined for these gel polymer electrolytes. The addition of BMPyTFSI to the P(EO)₂₀LiTFSI electrolyte results in an increase of the ionic conductivity, and at high BMPyTFSI concentration (BMPy⁺/Li⁺ = 1.0), the ionic conductivity reaches the value of 6.9 × 10⁻⁴ S/cm at 40 °C. The lithium ion transference numbers obtained from polarization measurements at 40 °C were found to decrease as the amount of BMPyTFSI increased. However, the lithium ionic conductivity increased with the content of BMPyTFSI. The electrochemical stability and interfacial stability for these gel polymer electrolytes were significantly improved due to the incorporation of BMPyTFSI.     

The conductivity and characterization of the plasticized polymer electrolyte based on the P(AN-co-GMA-IDA) copolymer with chelating group (II): The effect of free ion in the plasticized polymer electrolyte

A new gel-type polymer electrolyte (GPE) was made by the copolymerizing acrylonitrile (AN) and (2-methylacrylic acid 3-(bis-carboxymethylamino)-2-hydroxy-propyl ester) (GMA-IDA). The copolymer mixed with a plasticizer—propylene carbonate (PC) and lithium salt to form GPE. The lithium salts are LiCF₃SO₃, LiBr and LiClO₄. FT-IR spectra show that the lithium ion in the LiClO₄ system has the strongest interaction with the group based on the plasticized polymer. FT-IR spectra also indicate that CF₃SO₃⁻ prefers producing anion-cation association. Moreover, the ¹³C solid state NMR spectra for the carbons attached to the PC of GPE exhibited different level of chemical shift (158.5 ppm) when the different lithium salts were added to the electrolyte. The results of differential scanning calorimeter (DSC) also indicate that the LiClO₄ system has more free lithium ions; therefore, it has the maximum conductivity. In this study, the highest conductivity 2.98 × 10⁻³ S cm⁻¹ exists in AG2/PC = 20/80 wt.% system which contain 3 mmole (g-polymer)⁻¹ LiClO₄. Additionally, the polymer electrolytes, which contain GMA-IDA have better interfacial resistance stability with lithium electrode.     

Synthesis and electrochemical properties of lithium methacrylate-based self-doped gel polymer electrolytes

In this study, a strategy for synthesizing lithium methacrylate (LiMA)-based self-doped gel polymer electrolytes was described and the electrochemical properties were investigated by impedance spectroscopy and linear sweep voltammetry. LiMA was found to dissolve in ethylene carbonate (EC)/diethyl carbonate (DEC) (3/7, v/v) solvent after complexing with boron trifluoride (BF₃). This was achieved by lowering the ionic interactions between the methacrylic anion and lithium cation. As a result, gel polymer electrolytes consisting of BF₃-LiMA complexes and poly(ethylene glycol) diacrylate were successfully synthesized by radical polymerization in an EC/DEC liquid electrolyte. The FT-IR and AC impedance measurements revealed that the incorporation of BF₃ into the gel polymer electrolytes increases the solubility of LiMA and the ionic conductivity by enhancing the ion disassociations. Despite the self-doped nature of the LiMA salt, an ionic conductivity value of 3.0 × 10⁻⁵ S cm⁻¹ was achieved at 25 °C in the gel polymer electrolyte with 49 wt% of polymer content. Furthermore, linear sweep voltammetry measurements showed that the electrochemical stability of the gel polymer electrolyte was around 5.0 V at 25 °C.     

Effect of surface modified porous inorganic-organic hybrid polyphosphazene nanotubes on the properties of polyethylene oxide based solid polymer electrolytes

2-(2-methyloxyethoxy)ethanol modified poly (cyclotriphosphazene-co-4,4′-sufonyldiphenol) (PZS) nanotubes were synthesized and solid composite polymer electrolytes based on the surface modified polyphosphazene nanotubes added to PEO/LiClO₄ model system were prepared. Differential Scanning Calorimetry (DSC) and Scanning Electron Microscopy (SEM) were used to investigate the characteristics of the composite polymer electrolytes (CPE). The ionic conductivity, lithium ion transference number and electrochemical stability window can be enhanced after the addition of surface modified PZS nanotubes. The electrochemical investigation shows that the solid composite polymer electrolytes incorporated with PZS nanotubes have higher ionic conductivity and lithium ion transference number than the filler SiO₂. Maximum ionic conductivity values of 4.95 × 10⁻⁵ S cm⁻¹ at ambient temperature and 1.64 × 10⁻³ S cm⁻¹ at 80 °C with 10 wt % content of surface modified PZS nanotubes were obtained and the lithium ion transference number was 0.41. The good chemical properties of the solid state composite polymer electrolytes suggested that the inorganic-organic hybrid polyphosphazene nanotubes had a promising use as fillers in solid composite polymer electrolytes and the PEO₁₀-LiClO₄-PZS nanotubes solid composite polymer electrolyte can be used as a candidate material for lithium polymer batteries.     

Electrochemical performances of gel polymer electrolytes using tetra(ethylene glycol) diacrylate

A gel polymer electrolyte (GPE) was prepared using tetra(ethylene glycol) diacrylate monomer, benzoyl peroxide, and (). The LiCoO₂/GPE/graphite cells were prepared and their electrochemical properties were evaluated at various current densities and temperatures.The viscosity of the precursor containing the tetra(ethylene glycol) diacrylate monomer was around . The ionic conductivity of the gel polymer electrolyte at 20°C was around . The gel polymer electrolyte had good electrochemical stability up to vs. Li/Li⁺. The capacity of the LiCoO₂/GPE/graphite cell at rate was 63% of the discharge capacity at rate. The capacity of the cell at −10°C was 81% of the discharge capacity at 20°C. Discharge capacity of the cell with gel polymer electrolyte was stable with charge-discharge cycling.     

Study of electrochemical hydrogen charge/discharge properties of FePO4 for application as negative electrodes in hydrogen batteries

We report the electrochemical hydrogen charge/discharge properties of electrodes containing crystalline and amorphous FePO₄ as active material in KOH electrolyte. Crystalline and amorphous FePO₄ were synthesized by an alcohol-assisted precipitation method, and the powders obtained were characterized by X-ray diffraction. X-ray photoelectron spectroscopy is used to investigate the mechanism of hydrogen charge/discharge behavior of FePO₄. The electrochemical hydrogen charge/discharge properties of electrodes containing crystalline and amorphous FePO₄ were investigated for potential application as negative electrodes in rechargeable hydrogen batteries. In galvanostatic discharge/charge mode at 25 °C, the crystalline FePO₄ showed a maximum discharge capacity of 109 mA h g⁻¹, while the amorphous FePO₄ showed a maximum discharge capacity of 81.4 mA h g⁻¹. The electrochemical kinetic properties, exchange current density, and proton diffusivity were calculated using linear polarization measurement and the potential-step method.     

Rechargeable Li/LiFePO4 cells using N-methyl-N-butyl pyrrolidinium bis(trifluoromethane sulfonyl)imide-LiTFSI electrolyte incorporating polymer additives

We have incorporated polymer additives such as poly(ethylene glycol) dimethyl ether (PEGDME) and tetra(ethylene glycol) dimethyl ether (TEGDME) into N-methyl-N-butylpyrrolidinium bis(trifluoromethane sulfonyl)imide (PYR₁₄TFSI)-LiTFSI mixtures. The resulting PYR₁₄TFSI + LiTFSI + polymer additive ternary electrolyte exhibited relatively high ionic conductivity as well as remarkably low viscosity over a wide temperature range compared to the PYR₁₄TFSI + LiTFSI binary electrolytes. The charge/discharge cyclability of Li/LiFePO₄ cells containing the ternary electrolytes was investigated. We found that Li/PYR₁₄TFSI + LiTFSI + PEGDME (or TEGDME)/LiFePO₄ cells containing the two different polymer additives showed very similar discharge capacity behavior, with very stable cyclability at room temperature (RT). Li/PYR₁₄TFSI + LiTFSI + TEGDME/LiFePO₄ cells can deliver about 127 mAh/g of LiFePO₄ (74.7% of theoretical capacity) at 0.054 mA/cm² (0.2C rate) at RT and about 108 mAh/g of LiFePO₄ (63.4% of theoretical capacity) at 0.023 mA/cm² (0.1C rate) at −1 °C for the first discharge. The cell exhibited a capacity fading rate of approximately 0.09-0.15% per cycle over 50 cycles at RT. Consequently, the PYR₁₄TFSI + LiTFSI + polymer additive ternary mixture is a promising electrolyte for cells using lithium metal electrodes such as the Li/LiFePO₄ cell reported here. These cells showed the capability of operating over a significant temperature range (∼0-∼30 °C).     

Microwave solid-state synthesis and electrochemical properties of carbon-free Li3V2(PO4)3 as cathode materials for lithium batteries

Monoclinic Li₃V₂(PO₄)₃ can be rapidly synthesized at 750 °C for 5 min (MW5m) by using microwave solid-state synthesis method. The refined cell parameters and atomic coordination of the sample MW5m show some deviations compared with those of the sample synthesized in conventional solid-state synthesis method, especially the coordinate of Li atoms. Compared with the electrochemical properties of the carbon-coating sample Li₃V₂(PO₄)₃, the carbon-free sample MW5m presents well electrochemical properties. In the cut-off voltage of 3.0-4.3 V, MW5m sample presents a specific charge capacity of 132 mAh g⁻¹, almost equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹), and specific discharge capacity of 126.4 mAh g⁻¹. In the cut-off voltage of 3.0-4.8 V, MW5m shows an initial specific discharge capacity of 183.4 mAh g⁻¹ at 0.1 C, near the theoretical discharge capacity. In the cycle performance, the capacity fade of Li₃V₂(PO₄)₃ is dependent on the cut-off voltage and the preparation method, more capacity lost at relatively higher charge/discharge voltage. The reasons for the excellent electrochemical properties of Li₃V₂(PO₄)₃ rapidly synthesized in microwave field are discussed in detail.     

Synthesis of spinel LiMn2O4 with manganese carbonate prepared by micro-emulsion method

Micro-spherical particle of MnCO₃ has been successfully synthesized in CTAB-C₈H₁₈-C₄H₉OH-H₂O micro-emulsion system. Mn₂O₃ decomposed from the MnCO₃ is mixed with Li₂CO₃ and sintered at 800 °C for 12 h, and the pure spinel LiMn₂O₄ in sub-micrometer size is obtained. The LiMn₂O₄ has initial discharge specific capacity of 124 mAh g⁻¹ at discharge current of 120 mA g⁻¹ between 3 and 4.2 V, and retains 118 mAh g⁻¹ after 110 cycles. High-rate capability test shows that even at a current density of 16 C, capacity about 103 mAh g⁻¹ is delivered, whose power is 57 times of that at 0.2 C. The capacity loss rate at 55 °C is 0.27% per cycle.     

Preparation and characterization of carbon-coated LiFePO4 cathode materials for lithium-ion batteries with resorcinol-formaldehyde polymer as carbon precursor

LiFePO₄/C composites were synthesized by two methods using home-made amorphous nano-FePO₄ as the iron precursor and soluble starch, sucrose, citric acid, and resorcinol-formaldehyde (RF) polymer as four carbon precursors, respectively. The crystalline structures, morphologies, compositions, electrochemical performances of the prepared powders were investigated with XRD, TEM, Raman, and cyclic voltammogram method. The results showed that employing soluble starch and sucrose as the carbon precursors resulted in a deficient carbon coating on the surface of LiFePO₄ particle, but employing citric acid and RF polymer as the carbon precursors realized a uniform carbon coating on the surface of LiFePO₄ particle, and the corresponding thicknesses of the uniform carbon films are 2.5 nm and 4.5 nm, respectively. When RF polymer was used as the carbon precursor, the material showed the highest initial discharge capacity (138.4 mAh g^− 1 at 0.2 C at room temperature) and the best rate performance among the four materials.     

Anhydrous proton conducting polymer electrolytes based on poly(vinylphosphonic acid)-heterocycle composite material

The development of anhydrous proton conducting membrane is important for the operation of polymer electrolyte membrane fuel cell (PEMFC) at intermediate temperature (100-200 °C). In this study, we have investigated the acid-base hybrid materials by mixing of strong phosphonic acid polymer of poly(vinylphosphonic acid) (PVPA) with the high proton-exchange capacity and organic base of heterocycle, such as imidazole (Im), pyrazole (Py), or 1-methylimidazole (MeIm). As a result, PVPA-heterocycle composite material showed the high proton conductivity of approximately 10⁻³ S cm⁻¹ at 150 °C under anhydrous condition. In particular, PVPA-89 mol% Im composite material showed the highest proton conductivity of 7×10⁻³ S cm⁻¹ at 150 °C under anhydrous condition. Additionally, the fuel cell test of PVPA-89 mol% Im composite material using a dry H₂/O₂ showed the power density of approximately 10 mW cm⁻² at 80 °C under anhydrous conditions. These acid-base anhydrous proton conducting materials without the existence of water molecules might be possibly used for a polymer electrolyte membrane at intermediate temperature operations under anhydrous or extremely low humidity conditions.     

Synthesis of LiFePO4/C by solid-liquid reaction milling method

LiFePO₄/C was synthesized by the method of solid-liquid reaction milling, using FeCl₃·6H₂O, Li₂CO₃ and (NH₄)₂HPO₄ and glucose, which was used as reductant (carbon source). The samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), TG-DTA analysis, infrared absorption carbon-sulfur analysis and electrochemical performance test. The sample synthesized at 680 °C for 8 h showed, at initial discharge, a capacity of 155.8, 153.2, 148.5, 132.7 mAh g^− 1 at 0.2 °C, 0.5 °C, 1 °C and 3 °C rate respectively. The sample also showed an excellent capacity retention as there was no significant capacity fade after 10 cycles.     

CO tolerance and CO oxidation at Pt and Pt-Ru anode catalysts in fuel cell with polybenzimidazole-H3PO4 membrane

CO tolerance of H₂-air single cell with phosphoric acid doped polybenzidazole (PA-PBI) membrane was studied in the temperature range 140-180 °C using either dry or humidified fuel. Fuel composition was varied from neat hydrogen to 67% (vol.) H₂-33% CO mixtures. It was found that poisoning by CO of Pt/C and Pt-Ru/C hydrogen oxidation catalysts is mitigated by fuel humidification. Electrochemical hydrogen oxidation at Pt/C and Pt-Ru/C catalysts in the presence of up to 50% CO in dry or humidified H₂-CO mixtures was studied in a cell driven mode at 180 °C. High CO tolerance of Pt/C and Pt-Ru/C catalysts in FC with PA-PBI membrane at 180 °C can be ascribed to combined action of two factors—reduced energy of CO adsorption at high temperature and removal of adsorbed CO from the catalyst surface by oxidation. Rate of electrochemical CO oxidation at Pt/C and Pt-Ru/C catalysts was measured in a cell driven mode in the temperature range 120-180 °C. Electrochemical CO oxidation might proceed via one of the reaction paths—direct electrochemical CO oxidation and water-gas shift reaction at the catalyst surface followed by electrochemical hydrogen oxidation stage. Steady state CO oxidation at Pt-Ru/C catalyst was demonstrated using CO-air single cell with Pt-Ru/C anode. At 180 °C maximum CO-air single cell power density was 17 mW cm⁻² at cell voltage U = 0.18 V.     

New highly proton-conducting membrane poly(vinylpyrrolidone)(PVP) modified poly(vinyl alcohol)/2-acrylamido-2-methyl-1-propanesulfonic acid (PVA-PAMPS) for low temperature direct methanol fuel cells (DMFCs)

A new type of chemically cross-linked polymer blend membranes consisting of poly(vinyl alcohol) (PVA), 2-acrylamido-2-methyl-1-propanesulfonic acid (PAMPS) and poly(vinylpyrrolidone) (PVP) have been prepared and evaluated as proton conducting polymer electrolytes. The proton conductivity (σ) of the membranes was investigated as a function of cross-linking time, blending composition, water content and ion exchange capacity (IEC). Membranes were also characterized by FT-IR spectroscopy, thermogravimetric analysis (TGA), and the differential scanning calorimetry (DSC). Membrane swelling decreased with cross-linking time, accompanied by an improvement in mechanical properties and a small decrease in proton conductivity due to the reduced water absorption. The membranes attained 0.088 S cm⁻¹ of the proton conductivity and 1.63 mequiv g⁻¹ of IEC at 25±2 °C for a polymer composition PVA-PAMPS-PVP being 1:1:0.5 in mass, and a methanol permeability of 6.1×10⁻⁷ cm² s⁻¹, which showed a comparable proton conductivity to Nafion 117, but only one third of Nafion 117 methanol permeability under the same measuring conditions. The membranes displayed a relatively high oxidative durability without weight loss of the membranes (e.g. 100 h in 3% H₂O₂ solution and 20 h in 10% H₂O₂ solution at 60 °C). PVP, as a modifier, was found to play a crucial role in improving the above membrane performances.     

Crystal structure and electrochemical performance of Li3V2(PO4)3 synthesized by optimized microwave solid-state synthesis route

To investigate the crystal structure and electrochemical performance of samples synthesized under different microwave solid-state synthesis condition, a series of Li₃V₂(PO₄)₃ samples has been synthesized at five different temperatures for 3-5 min and at 750 °C for various time. The as-synthesized Li₃V₂(PO₄)₃ samples are characterized and studied by ICP-AES analysis, X-ray diffraction (XRD), Rietveld analysis, scanning and transmission electron microcopy (SEM and TEM). At relatively lower temperature (650 °C) and very short reaction time (3 min), pure phase of Li₃V₂(PO₄)₃ could be synthesized in microwave irradiation field. The crystal structure and Li atomic fractional coordinate present a significant deviation upon the change of microwave irradiation temperature and time. Relatively, the diffusion ability of lithium cations and the electrochemical performance are affected. Under the proper reaction temperature and time, the carbon-free samples MW750C5m and MW850C3m show the best specific discharge capacity 126.4 and 132 mAh g⁻¹ at the voltage range of 3.0-4.3 V, near the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). At the voltage range of 3-4.8 V, the sample MW750C5m presents the best initial specific charge capacity of 197 mAh g⁻¹, equivalent to the reversible cycling of three lithium ions per Li₃V₂(PO₄)₃ formula unit (197 mAh g⁻¹). The initial discharge capacity, the samples MW750C5m and MW850C3m present high specific discharge capacity 183.4 and 175.7 mAh g⁻¹, respectively. The relationship among microwave irradiation condition, crystal structure, lithium atomic fractional coordinates and the electrochemical performance have been discussed in detail.     

Highly ion conductive flexible films composed of network polymers based on polymerizable ionic liquids

Ionic liquid-type polymer brushes having different hydrocarbon (HC) chain lengths between polymerizable group and imidazolium ring were synthesized. When the carbon number of HC chain was 6, the ionic liquid-type polymer brush exhibited the highest ionic conductivity of 1.37×10⁻⁴ S cm⁻¹ at 30 °C, reflecting low T_g of −60 °C. Moreover, for the first time, we succeeded in obtaining transparent and flexible films without considerable decrease in the ionic conductivity as compared with that of corresponding monomers by using suitable cross-linkers. The most ion conductive (1.1×10⁻⁴ S cm⁻¹ at 30 °C) film was obtained when tetra(ethylene glycol)diacrylate was used 0.5 mol% to ionic liquid monomer as the cross-linker. This film is one of excellent conductive films among single-ion conductive materials.