Superior low-temperature hydrogen release from the ball-milled NH3BH3–LiNH2–LiBH4 composite

In the present study, we employed a multi-component combination strategy to constitute an AB/LiNH₂/LiBH₄ composite system. Our study found that mechanically milling the AB/LiNH₂/LiBH₄ mixture in a 1:1:1 molar ratio resulted in the formation of LiNH₂BH₃ (LiAB) and new crystalline phase(s). A spectral study of the post-milled and the relevant samples suggests that the new phase(s) is likely ammoniate(s) with a formula of Li_2−x(NH₃)(NH₂BH₃)_1−x(BH₄) (0 < x < 1). The decomposition behaviors of the Li_2−x(NH₃)(NH₂BH₃)_1−x(BH₄)/xLiAB composite were examined using thermal analysis and volumetric method in a wide temperature range. It was found that the composite exhibited advantageous dehydrogenation properties over LiAB and LiAB·NH₃ at moderate temperatures. For example, it can release ∼7.1 wt% H₂ of purity at temperature as low as 60 °C, with both the dehydrogenation rate and extent far exceeding that of LiAB and LiAB·NH₃. A selectively deuterated composite sample has been prepared and examined to gain insight into the dehydrogenation mechanism of the Li_2−x(NH₃)(NH₂BH₃)_1−x(BH₄)/xLiAB composite. It was found that the LiBH₄ component does not participate in the dehydrogenation reaction at moderate temperatures, but plays a key role in strengthening the coordination of NH₃. This is believed to be a major mechanistic reason for the favorable dehydrogenation property of the composite at moderate temperatures.     

Revision of the NaBO2–H2O phase diagram for optimized yield in the H2 generation through NaBH4 hydrolysis

The binary phase diagram NaBO₂–H₂O at ambient pressure, which defines the different phase equilibria that could be formed between borates, end-products of NaBH₄ hydrolysis, has been reviewed. Five different solid borates phases have been identified: NaBO₂·4H₂O (Na[B(OH)₄]·2H₂O), NaBO₂·2H₂O (Na[B(OH)₄]), NaBO₂·2/3H₂O (Na₃[B₃O₄(OH)₄]), NaBO₂·1/3H₂O (Na₃[B₃O₅(OH)₂]) and NaBO₂ (Na₃[B₃O₆]), and their thermal stabilities have been studied. The boundaries of the different Liquid + Solid equilibria for the temperature range from −10 to 80 °C have been determined, confirming literature data at low temperature (20–50 °C). Moreover the following eutectic transformation, Liq. → Ice + NaBO₂·4H₂O, occurring at −7 °C, has been determined by DSC. The Liquid–Vapour domain has been studied by ebullioscopy. The invariant transformation Liq. → Vap. + NaBO₂·2/3H₂O has been estimated at 131.6 °C. This knowledge is paramount in the field of hydrogen storage through NaBH₄ hydrolysis, in which borate compounds were obtained as hydrolysis reaction products. As a consequence, the authors propose a comparison with previous NaBO₂–H₂O binary phase diagrams and its consequence related to hydrogen storage through NaBH₄ hydrolysis.     

Reversible hydrogenation/dehydrogenation performances of the Na2LiAlH6–Mg(NH2)2 system

Complex hydrides and Metal–N–H-based materials have attracted considerable attention due to their high hydrogen content. In this paper, a novel amide–hydride combined system was prepared by ball milling a mixture of Na₂LiAlH₆–Mg(NH₂)₂ in a molar ratio of 1:1.5. The hydrogen storage performances of the Na₂LiAlH₆–1.5Mg(NH₂)₂ system were systematically investigated by a series of dehydrogenation/hydrogenation evaluation and structural analyses. It was found that a total of ∼5.08 wt% of hydrogen, equivalent to 8.65 moles of H atoms, was desorbed from the Na₂LiAlH₆–1.5Mg(NH₂)₂ combined system. In-depth investigations revealed that the variable milling treatments resulted in the different dehydrogenation reaction pathways due to the combination of Al and N caused by the energetic milling. Hydrogen uptake experiment indicated that only ∼4 moles of H atoms could be reversibly stored in the Na₂LiAlH₆–1.5Mg(NH₂)₂ system perhaps due to the formation of AlN and Mg₃N₂ after dehydrogenation.     

Processing analysis of the ternary LiNH2–MgH2–LiBH4 system for hydrogen storage

In this article, we investigate the ternary LiNH₂–MgH₂–LiBH₄ hydrogen storage system by adopting various processing reaction pathways. The stoichiometric ratio of LiNH₂:MgH₂:LiBH₄ is kept constant with a 2:1:1 molar ratio. All samples are prepared using solid-state mechano-chemical synthesis with a constant rotational speed, but with varying milling duration. Furthermore, the order of addition of parent compounds as well as the crystallite size of MgH₂ are varied before milling. All samples are intimate mixtures of Li–B–N–H quaternary hydride phase with MgH₂, as evidenced by XRD and FTIR measurements. It is found that the samples with MgH₂ crystallite sizes of approximately 10 nm exhibit lower initial hydrogen release at a temperature of 150 °C. Furthermore, it is observed that the crystallite size of Li–B–N–H has a significant effect on the amount of hydrogen release with an optimum size of 28 nm. The as-synthesized hydrides exhibit two main hydrogen release temperatures, one around 160 °C and the other around 300 °C. The main hydrogen release temperature is reduced from 310 °C to 270 °C, while hydrogen is first reversibly released at temperatures as low as 150 °C with a total hydrogen capacity of ∼6 wt.%. Detailed thermal, capacity, structural and microstructural properties are discussed and correlated with the activation energies of these materials.     

Catalytic effect of MgFe2O4 on the hydrogen storage properties of Na3AlH6–LiBH4 composite system

The effect of MgFe₂O₄ on the hydrogen storage properties of the composite Na₃AlH₆4LiBH₄ was studied for the first time, where it was found that MgFe₂O₄ addition decreased the onset desorption temperature of Na₃AlH₆4LiBH₄. Hydrogen (～9.5 wt%) was released in three stages and the dehydrogenation temperatures were reduced to 80 °C, 350 °C, and 430 °C for the first, second, and third stage, respectively. The absorption kinetics of Na₃AlH₆4LiBH₄ was also significantly improved due to the catalytic effect of MgFe₂O₄. Using Kissinger analysis, the apparent activation energies of decomposition of the Li₃AlH₆ and NaBH₄ stages in Na₃AlH₆4LiBH₄-10 wt% MgFe₂O₄ were calculated to be 72 and 141 kJ/mol, respectively. These values were considerably lower than the corresponding values for the undoped composite. X-ray diffraction analysis revealed the formation of new products such as MgO and Fe during the heating process. Our results suggest that MgFe₂O₄ enhanced the hydrogen storage properties of Na₃AlH₆4LiBH₄ through the formation of active species, such as MgO and Fe.     

Hydrogen storage properties and mechanisms of the Mg(BH4)2–NaAlH4 system

Hydrogen storage properties and mechanisms of the combined Mg(BH₄)₂–NaAlH₄ system were investigated systematically. It was found that during ball milling, the Mg(BH₄)₂–xNaAlH₄ combination converted readily to the mixture of NaBH₄ and Mg(AlH₄)₂ with a metathesis reaction. The post-milled samples exhibited an apparent discrepancy in the hydrogen desorption behavior with respect to the pristine Mg(BH₄)₂ and NaAlH₄. Approximately 9.1 wt% of hydrogen was released from the Mg(BH₄)₂–2NaAlH₄ composite milled for 24 h with an onset temperature of 101 °C, which is lowered by 105 and 139 °C than that of NaAlH₄ and Mg(BH₄)₂, respectively. At initial heating stage, Mg(AlH₄)₂ decomposed first to produce MgH₂ and Al with hydrogen release. Further elevating operation temperatures gave rise to the reaction between MgH₂ and Al and the self-decomposition of MgH₂ to release more hydrogen and form the Al_0.9Mg_0.1 solid solution and Mg. Finally, NaBH₄ reacted with Mg and partial Al_0.9Mg_0.1 to liberate all of hydrogen and yield the resultant products of MgAlB₄, Al₃Mg₂ and Na. The dehydrogenated sample could take up ∼6.5 wt% of hydrogen at 400 °C and 100 atm of hydrogen pressure through a more complicated reaction process. The hydrogenated products consisted of NaBH₄, MgH₂ and Al, indicating that the presence of Mg(AlH₄)₂ is significantly favorable for reversible hydrogen storage in NaBH₄ at moderate temperature and hydrogen pressure.     

Effects of MoS2 addition on the hydrogen storage properties of 2LiBH4–MgH2 systems

A 2LiBH₄–MgH₂–MoS₂ composite was prepared by solid-state ball milling, and the effects of MoS₂ as an additive on the hydrogen storage properties of 2LiBH₄–MgH₂ system together with the corresponding mechanism were investigated. As shown in the TG–DSC and MS results, with the addition of 20 wt.% of MoS₂, the onset dehydrogenation temperature is reduced to 206 °C, which is 113 °C lower than that of the pristine 2LiBH₄–MgH₂ system. Meanwhile, the total dehydrogenation amount can be increased from 9.26 wt.% to 10.47 wt.%, and no gas impurities such as B₂H₆ and H₂S are released. Furthermore, MoS₂ improves the dehydrogenation kinetics, and lowers the activation energy (E_a) 34.49 kJ mol⁻¹ of the dehydrogenation reaction between Mg and LiBH₄ to a value lower than that of the pristine 2LiBH₄–MgH₂ sample. According to the XRD test, Li₂S and MoB₂ are formed by the reaction between LiBH₄ and MoS₂, which act as catalysts and are responsible for the improved hydrogen storage properties of the 2LiBH₄–MgH₂ system.     

O2/CO2气氛添加CaCO3对徐州烟煤PM2.5排放的影响

采用管式炉研究了在O2/CO2气氛下添加CaCO3对PM2.5(空气动力学直径小于2.5,μm的颗粒物)排放特性的影响.试验采用荷电低压撞击器(ELPI)采集和分析燃烧后的PM2.5.结果表明,添加CaCO3是燃烧过程中影响PM2.5生成的重要因素.添加CaCO3后,生成PM1的数密度和质量浓度均降低,而PM1-2.5的数密度和质量浓度均略有增加,PM2.5粒径分布均呈双峰分布,峰值点分别出现在0.2,μm和2.0,μm左右.随着CaCO3添加质量分数的增加,PM2.5中的S、Pb、Cu、Na和K几种元素的浓度呈下降趋势.     

Interaction in the Ce3Co8Si–H2 system

Interaction of hydrogen with Ce₃Co₈Si intermetallic compound (IMC) has been studied. IMC Ce₃Co₈Si absorbs hydrogen and forms a hydride phase at 11 atm and 50 °C. X-ray analysis of Ce₃Co₈Si H_10.2 saturated hydride phase lattice showed that it has the symmetry of the initial compound and is expanded with strong anisotropy due to increased c parameter. Analysis of hydrogen desorption isotherms in Ce₃Co₈Si–H₂ system has revealed that the decomposition of hydride phase occurred in one stage. The heat of hydride phase formation was calculated on the base of obtained equilibrium pressures data at 50, 60 and 70 °C. The results obtained demonstrate that Ce₃Co₈Si intermetallic compound may be used as reversible accumulator of hydrogen in medium temperatures interval.     

Adiabatic burning velocity of H2–O2 mixtures diluted with CO2/N2/Ar

Global warming due to CO₂ emissions has led to the projection of hydrogen as an important fuel for future. A lot of research has been going on to design combustion appliances for hydrogen as fuel. This has necessitated fundamental research on combustion characteristics of hydrogen fuel. In this work, a combination of experiments and computational simulations was employed to study the effects of diluents (CO₂, N₂, and Ar) on the laminar burning velocity of premixed hydrogen/oxygen flames using the heat flux method. The experiments were conducted to measure laminar burning velocity for a range of equivalence ratios at atmospheric pressure and temperature (300 K) with reactant mixtures containing varying concentrations of CO₂, N₂, and Ar as diluents. Measured burning velocities were compared with computed results obtained from one-dimensional laminar premixed flame code PREMIX with detailed chemical kinetics and good agreement was obtained. The effectiveness of diluents in reduction of laminar burning velocity for a given diluent concentration is in the increasing order of argon, nitrogen, carbon dioxide. This may be due to increased capabilities either to quench the reaction zone by increased specific heat or due to reduced transport rates. The lean and stoichiometric H₂/O₂/CO₂ flames with 65% CO₂ dilution exhibited cellular flame structures. Detailed three-dimensional simulation was performed to understand lean H₂/O₂/CO₂ cellular flame structure and cell count from computed flame matched well with the experimental cellular flame.     

O2/CO2和O2/N2氛围下煤粉富氧燃烧数值模拟

在目前煤炭依然作为能源主体的背景下，控制燃煤污染物排放有着重要意义。基于CFD数值模拟，建立伴流燃烧器模型，控制燃料、氧化剂入口流量恒定，设计了O₂/CO₂、O₂/N₂氧化剂氛围中O₂浓度在21%～40%内的多种工况，对煤粉燃烧特性及燃烧产生的污染物进行了研究。分析了不同工况下煤粉燃烧的温度分布、燃烧速率、碳烟、NO_x的生成情况。结果显示，在O₂/CO₂、O₂/N₂两种氧化剂氛围中，随着O₂浓度的上升，煤粉燃烧温度升高、燃烧速率增大，碳烟生成量均增加，同等O2浓度条件下，O₂/CO₂氛围的煤粉燃烧温度和燃烧速率均高于O₂/N₂氛围，碳烟生成量小于O₂/N₂氛围，且O₂/CO₂...     

Improved dehydrogenation properties of the combined Mg(BH4)2·6NH3–nNH3BH3 system

A combined strategy via mixing Mg(BH₄)₂·6NH₃ with ammonia borane (AB) is employed to improve the dehydrogenation properties of Mg(BH₄)₂·6NH₃. The combined system shows a mutual dehydrogenation improvement in terms of dehydrogenation temperature and hydrogen purity compared to the individual components. A further improved hydrogen liberation from the Mg(BH₄)₂·6NH₃–6AB is achieved with the assistance of ZnCl₂, which plays a crucial role in stabilizing the NH₃ groups and promoting the recombination of NH^δ+?HB^δ−. Specifically, the Mg(BH₄)₂·6NH₃–6AB/ZnCl₂ (with a mole ratio of 1:0.5) composite is shown to release over 7 wt.% high-pure hydrogen (>99 mol%) at 95 °C within 10 min, thereby making the combined system a promising candidate for solid hydrogen storage.     

HI extraction by H3PO4 in the Sulfur–Iodine thermochemical water splitting cycle: Composition optimization of the HI/H2O/H3PO4/I2 biphasic quaternary system

Iodine excess separation from hydriodic acid (HI) is one of the most challenging steps of the Sulfur–Iodine thermochemical water splitting cycle. One promising method is the extraction of HI by using phosphoric acid (H₃PO₄), with the subsequent separation of gaseous hydriodic acid from water and H₃PO₄ by a distillation step.     

Oxidative steam reforming of ethanol over Ni/Al2O3 catalysts promoted by CeO2, ZrO2 and CeO2–ZrO2

Oxidative steam reforming of ethanol at low oxygen to ethanol ratios was investigated over nickel catalysts on Al₂O₃ supports that were either unpromoted or promoted with CeO₂, ZrO₂ and CeO₂–ZrO₂. The promoted catalysts showed greater activity and a higher hydrogen yield than the unpromoted catalyst. The characterization of the Ni-based catalysts promoted with CeO₂ and/or ZrO₂ showed that the variations induced in the Al₂O₃ by the addition of CeO₂ and/or ZrO₂ alter the catalyst's properties by enhancing Ni dispersion and reducing Ni particle size. The promoters, especially CeO₂–ZrO₂, improved catalytic activity by increasing the H₂ yield and the CO₂/CO and the H₂/CO values while decreasing coke formation. This results from the addition of ZrO₂ into CeO₂. This promoter highlights the advantages of oxygen storage capacity and of mobile oxygen vacancies that increase the number of surface oxygen species. The addition of oxygen facilitates the reaction by regenerating the surface oxygenation of the promoters and by oxidizing surface carbon species and carbon-containing products.     

The oxygen-releasing step in the water splitting cycle by MnFe2O4–Na2CO3 system

Investigation of the feasibility of the thermochemical two-step water splitting cycle based on MnFe₂O₄/Na₂CO₃ system is reported. Influence of temperature and carbon dioxide pressure on the oxygen-releasing step was investigated. XRD analysis was applied to obtain phase identification of reacted powders at investigated experimental conditions. Different sodium sub-stoichiometric Na_1−δ(Mn_1/3Fe_2/3)O_2−δ/2 compounds were observed and their structure determined by using Rietveld analysis. Selected experimental conditions permitted to define a T/pCO2$T/p_{{\text{CO}}_{\text{2}}}$ phase diagram, showing different solid phases coexistence regions. Experimental conditions that permit complete regeneration of the initial MnFe₂O₄/Na₂CO₃ mixture were identified (field I in the reported diagram), demonstrating the possibility of full chemical cyclical operation of the system.     

Study on the hydrogen storage properties and reaction mechanism of NaAlH4–MgH2–LiBH4 ternary-hydride system

In this paper, we report the hydrogen storage properties and reaction mechanism of NaAlH₄–MgH₂–LiBH₄ (1:1:1) ternary-hydride system prepared by ball milling. It was found that during ball milling, the NaAlH₄/MgH₂/LiBH₄ combination converted readily to the mixture of LiAlH₄/MgH₂/NaBH₄ and there is a mutual destabilization among the hydrides. Three major dehydrogenation steps were observed in the system, which corresponds to the decomposition of LiAlH₄, MgH₂, and NaBH₄, respectively. The onset dehydrogenation temperature of MgH₂ in this system is observed at around 275 °C, which is over 55 °C lower from that of as-milled MgH₂. Meanwhile, NaBH₄-relevant decomposition showed significant improvement, starts to release hydrogen at 370 °C, which is reduced by about 110 °C compared to the as-milled NaBH₄. The second and third steps decomposition enthalpy of the system were determined by differential scanning calorimetry measurements and the enthalpies were changed to be 61 and 100 kJ mol⁻¹ H₂ respectively, which are smaller than that of MgH₂ and NaBH₄ alone. From the Kissinger plot, the apparent activation energy, E_A, for the decomposition of MgH₂ and NaBH₄ in the composite was reduced to 96.85 and 111.74 kJ mol⁻¹ respectively. It is believed that the enhancement of the dehydrogenation properties was attributed to the formation of intermediate compounds, including Li–Mg, Mg–Al, and Mg–Al–B alloys, upon dehydrogenation, which change the thermodynamics of the reactions through altering the de/rehydrogenation pathway.     

Improved hydrogen storage performance of the LiNH2–MgH2–LiBH4 system by addition of ZrCo hydride

Significant improvements in the hydrogen absorption/desorption properties of the 2LiNH₂–1.1MgH₂–0.1LiBH₄ composite have been achieved by adding 3wt% ZrCo hydride. The composite can absorb 5.3wt% hydrogen under 7.0 MPa hydrogen pressure in 10 min and desorb 3.75wt% hydrogen under 0.1 MPa H₂ pressure in 60 min at 150 °C, compared with 2.75wt% and 1.67wt% hydrogen under the same hydrogenation/dehydrogenation conditions without the ZrCo hydride addition, respectively. TPD measurements showed that the dehydrogenation temperature of the ZrCo hydride-doped sample was decreased about 10 °C compared to that of the pristine sample. It is concluded that both the homogeneous distribution of ZrCo particles in the matrix observed by SEM and EDS and the destabilized N–H bonds detected by IR spectrum are the main reasons for the improvement of H-cycling kinetics of the 2LiNH₂–1.1MgH₂–0.1LiBH₄ system.     

The hydrogen storage properties and reaction mechanism of the NaAlH4 + Ca(BH4)2 composite system

The hydrogen storage properties and reaction mechanism of the combined NaAlH₄ + Ca(BH₄)₂ (2:1) composite system was investigated in the present study. Analyses show that after 6 h of milling, the NaAlH₄ + Ca(BH₄)₂ combination fully converted to the mixture of Ca(AlH₄)₂ + NaBH₄, and a metathesis reaction occurred between the hydrides. Four major dehydrogenation stages were observed in the system, which corresponds to the decomposition of Ca(AlH₄)₂, CaAlH₅, CaH₂ and NaBH₄, respectively. The onset desorption temperature of the composite system is reduced to 125 °C, which is much lower than a unary component of NaAlH₄ and Ca(BH₄)₂. The de/rehydrogenation kinetics of the composite system had improve at a higher temperature. From the Kissinger plot, the apparent activation energies for the decomposition of CaAlH₅ and NaBH₄ in the composite system were reduced to 142.9 and 146.5 kJ/mol, respectively. It is believed that the formation of AlCa, AlB and CaB alloys during the dehydrogenation process is responsible for the distinct reduction in the onset desorption temperature and kinetics enhancement of the 2NaAlH₄ + Ca(BH₄)₂ composite system.     

A numerical study on the effects of H2 addition in non-premixed turbulent combustion of C3H8–H2–N2 mixture using a steady flamelet approach

This study has been implemented in two sections. At first, the turbulent jet flame of DLR-B is simulated by combining the k–ε turbulence model and a steady flamelet approach. The DLR-B flame under consideration has been experimentally investigated by Meier et al. who obtained velocity and scalar statistics. The fuel jet composition is 33.2% H₂, 22.1% CH₄ and 44.7% N₂ by volume. The jet exit velocity is 63.2 m/s resulting in a Reynolds number of 22,800. Our focus in the first part is to validate the developed numerical code. Comparison with experiments showed good agreement for temperature and species distribution. At the second part, we exchanged methane with propane in the fuel composition whilst maintaining all other operating conditions unchanged. We investigated the effect of hydrogen concentration on C₃H₈–H₂–N₂ mixtures so that propane mole fraction extent is fixed. The hydrogen volume concentration rose from 33.2% up to 73.2%. The achieved consequences revealed that hydrogen addition produces elongated flame with increased levels of radiative heat flux and CO pollutant emission. The latter behavior might be due to quenching of CO oxidation process in the light of excessive cold air downstream of reaction zone.     

H2 and CH4 oxidation on Gd0.2Ce0.8O1.9 infiltrated SrMoO3–yttria-stabilized zirconia anode for solid oxide fuel cells

Strontium molybdate (SrMoO₃) as an electronic conductor was incorporated with yttria-stabilized zirconia (YSZ) to form an anode scaffold for solid oxide fuel cells. Gd_0.2Ce_0.8O_1.9 (GDC) nanoparticles were introduced by wet impregnation to complete the Ni-free GDC infiltrated SrMoO₃–YSZ anode fabrication. The effects of SrMoO₃ on the electrode conductivity and GDC infiltration on the catalytic activity were examined. A pronounced performance improvement was observed both on wet H₂ and CH₄ oxidation for the 56 wt.% GDC infiltrated SrMoO₃–YSZ. In particular, the polarization resistance decreased from 8 Ω cm² to 0.5 Ω cm² under wet H₂ (3% H₂O) at 800 °C with the introduction of GDC. Under wet CH₄ at 900 °C, a maximum power density of 160 mW cm⁻² was obtained and no carbon deposition was observed on the anode. It was found that the addition of H₂O in the anode caused an increase of electrode ohmic resistance and a decrease of open circuit voltage. Redox cycling stability was investigated and only a slight drop in cell performance was observed after 5 cycles. These results suggest that GDC infiltrated SrMoO₃–YSZ is a promising anode material for solid oxide fuel cells.