Catalytic CO2 reforming of CH4 over MgAl2O4 supported Ni-Co catalysts for the syngas production

Ni, Co and Ni–Co bimetallic catalysts of different ratios were synthesized by the Incipient Wetness Impregnation Method (IWI) over Magnesium Aluminate support, keeping the total metal loading 15 wt.%, characterized and tested for the reforming of methane with carbon dioxide at 873 K and 1 atm pressure. Magnesium Aluminate supported catalysts were also compared with Al₂O₃ supported Ni catalysts with similar metal loading. The results obtained revealed that MgAl₂O₄ exhibited excellent thermal stability as compared to Al₂O₃ as support at higher temperatures. Ni–Co catalyst, with an explicit Ni:Co (3:1) ratio for the 75Ni25Co/MgAl₂O₄ provided the highest CH₄ conversion and was about 1.82 times that of the 100Ni/MgAl₂O₄; CO₂ conversion also followed similar trends. Co-existence of Ni and Co with synergic effect in an explicit Ni:Co (3:1) ratio reduced the reduction temperature and increased the amount of metal in 75Ni25Co/MgAl₂O₄. CH₄ and CO₂ conversions, TOF_DRM, H₂: CO ratios and catalyst deactivations were related to the concentrations of the Ni–Co and particularly an explicit ratio of 3:1 for the Ni:Co in 75Ni25Co/MgAl₂O₄ catalyst provided the best initial & final conversions, TOF_DRM and H₂:CO ratio. Detail carbon analysis suggested that the type of coke deposited on 75Ni25Co/MgAl₂O₄ after the DRM reaction is of the same nature and are originating from the CH₄ cracking reaction and are of reactive type.     

Highly stable and active Ni-mesoporous alumina catalysts for dry reforming of methane

Nanostructured Ni-incorporated mesoporous alumina (MAl) materials with different Ni loading (7, 10 and 15 wt %) were prepared by a template assisted hydrothermal synthesis method and tested as catalysts for CO₂ reforming of methane under different conditions (nickel loading, gas hourly space velocity (GHSV), reaction temperature and time-on-stream (TOS)). The most active catalyst tested (Ni(10 wt%)-MAl) showed a very high stability over 200 h compared to a Ni(10 wt%)/γ-Al₂O₃ prepared using a co-precipitation method which had a significant loss in activity after only ∼4 h of testing. The high stability of the Ni-MAl materials prepared by the template assisted method was due to the Ni nanoparticles in these catalysts being highly stable towards migration/sintering under the reaction conditions used (800 °C, 52,000 mL h⁻¹ g⁻¹). The low susceptibility of the Ni nanoparticles in these catalysts to migration/sintering was most likely due to a strong Ni-support interaction and/or active metal particles being confined to the mesoporous channels of the support. The Ni-MAl catalysts also had significantly lower amounts of carbon deposited compared to the catalyst prepared using the co-precipitation method.     

Low-temperature partial oxidation of methane over Pd–Ni bimetallic catalysts supported on CeO2

Monometallic Pd and Ni and bimetallic Pd–Ni catalysts supported on CeO₂ are prepared via mechanochemical and conventional incipient wetness impregnation methods and tested for the production of syngas by the partial oxidation of methane. Compared with monometallic Ni/CeO₂ and Pd/CeO₂, bimetallic Pd–Ni/CeO₂ catalysts show considerable higher methane conversion and syngas yield. Additionally, the bimetallic catalysts prepared by ball milling produce syngas at lower temperature. Different preparation parameters, such as metal loading, Pd/Ni ratio, milling energy, milling time and order of incorporation of the metals are examined. The best performance is obtained with a bimetallic catalyst prepared at 50 Hz for 20 min with only 0.12 wt% Pd and 1.38 wt% Ni. Stability tests demonstrate superior stability for bimetallic Pd–Ni/CeO₂ catalysts prepared by a mechanochemical approach. From the characterization results, this is explained in terms of an impressive dispersion of metal species with a strong interaction with the surface of CeO₂.     

Rh promoted and ZrO2/Al2O3 supported Ni/Co based catalysts: High activity for CO2 reforming,steam–CO2 reforming and oxy–CO2 reforming of CH4

Ni (2.5 wt%) and Co (2.5 wt%) supported over ZrO₂/Al₂O₃ were prepared by following a hydrolytic co-precipitation method. The synthesized catalysts were further promoted by Rh incorporation (0.01–1.00 wt%) and tested for their catalytic performance for dry CO₂ reforming, combined steam–CO₂ reforming and oxy–CO₂ reforming of methane for production of syngas. The catalysts were characterized by using N₂ physical adsorption, XRD, H₂–TPR, SEM, CO₂–TPD, NH₃–TPD, TEM and TGA. The results revealed that ZrO₂ phase was in crystalline form in the catalysts along with amorphous Al oxides. Ni and Co were confirmed to be in their respective spinel phases that were reducible to metallic form at 800 °C under H₂. Ni and Co were well dispersed with their nano-crystalline nature. The catalyst with 0.2% loading of Rh showed superior performance in the studied reactions for reforming of methane. This catalyst also showed good coke resistance ability for dry CO₂ reforming reaction with 3.8 wt% of carbon formation during the reaction as compared to 11.6 wt% carbon formation over the catalyst without Rh. The catalyst performance was stable throughout the reaction time for CH₄ conversions, irrespective of carbon formation with slight decline (～1%) in CO₂ conversion. For dry CO₂ reforming reaction, this catalyst showed good conversion for both CH₄ and CO₂ (67.6% and 71.8% respectively) with a H₂/CO ratio of 0.84, while for the Oxy-CO₂ reforming reaction, the activity was superior with CH₄ and CO₂ conversions (73.7% and 83.8% respectively) and H₂/CO ratio of 1.05.     

Biogas reforming over La-promoted Ni/SBA-16 catalyst for syngas production: Catalytic structure and process activity investigation

Biogas, a mixture of CO₂/CH₄, is reasonable for conversion to syngas (H₂/CO) by dry methane reforming (DMR) reaction. The modification of Ni/SBA-16 with a lanthanum promoter using the co-impregnation technique is investigated in this study. The temperature of reaction (600–750 °C), La loading (3.85–11.56 wt%), and Ni loading (10–30 wt%) are the parameters that are varied for maximizing reaction conversions. The synthesized catalysts and SBA-16 supporting material were characterized by several methods before and after reaction. According to the analysis, the existence of La₂O₃ particles on the catalyst's surface has decreased the particle sizes, as well as enhanced their dispersion. Therefore, the maximum CH₄ conversion of 94.21%, CO₂ conversion of 90.12%, H₂ yield of 90.53%, and H₂/CO molar ratio of 2.03 are achieved using 20Ni-5.78La/SBA16 at 700 °C. Besides, this catalyst showed lower deposited coke and higher stability compared with other synthesized catalysts.     

Enhanced coke suppression by using phosphate-zirconia supported nickel catalysts under dry methane reforming conditions

Ni based phosphate zirconium catalysts were prepared by impregnation technique and used under CH₄ dry reforming conditions. Catalysts (x%Ni/8%PO₄–Zr, where x = 5, 10, 15 or 20) were characterized by nitrogen physical adsorption-desorption, X-ray diffraction, temperature programmed reduction, CO₂ and NH₃ temperature programmed desorption, thermal gravimetric analysis and transmission electron microscopy (TEM-EDAX). Catalysts displayed a typical mesoporous structure and different reducibility grade as a function of Ni loading, diagnostic of a different extent of metal-support interaction. Activity and stability strongly depend upon Ni loading while the best performance was observed for catalyst characterized by a Ni loading of 10 wt%. The CO₂-TPD profiles of spent catalysts indicated that such catalyst had more tendency to gasify coke formed over the catalyst surface. TGA analysis of used catalysts quantitatively showed that catalysts at higher Ni loading deactivated as result of huge graphitic carbon formation on catalyst surface. On the contrary, system 10%Ni8%PO₄/ZrO₂ turns out to be an excellent candidate to conduct the methane reforming reaction with CO₂ without coke formation at high CH₄ and CO₂ conversions. Phosphate play a fundamental role in promoting Ni–ZrO₂ interaction which reflects in the stabilization of catalytic system against metal sintering and coke formation.     

Biogas reforming over bimetallic PdNi catalysts supported on phosphorus-modified alumina

A series of bimetallic PdNi catalysts supported on alumina modified with different amounts of phosphorus (0.5-5 wt%) were prepared. The effect of phosphorus content on the structure, surface properties and catalytic behavior of supported PdNi catalysts in biogas reforming was studied. The physicochemical properties of the samples were characterized by using different techniques: N₂ adsorption-desorption isotherms, X-ray diffraction (XRD), UV-vis diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS), temperature-programmed reduction (TPR), temperature-programmed desorption of ammonia (TPD), thermogravimetric and differential thermal analysis (TG/DTA) and scanning transmission electron microscopy (STEM). The catalytic properties of the catalysts were evaluated in the reaction of reforming of methane with CO₂. It was shown that increasing the P content (≥1 wt%) leads to agglomeration of the metal Ni particles, as well as to increase of the total acidity of the catalysts. Within bimetallic system, the PdNi catalyst with 0.5 wt% phosphorus showed the best performance and stability caused by the presence of highly dispersed nickel particles on the catalyst surface due to the strong interaction between supported species and alumina.     

Metal foam-supported Pd–Rh catalyst for steam methane reforming and its application to SOFC fuel processing

Pd–Rh/metal foam catalyst was studied for steam methane reforming and application to SOFC fuel processing. Performance of 0.068 wt% Pd–Rh/metal foam catalyst was compared with 13 wt% Ni/Al₂O₃ and 8 wt% Ru/Al₂O₃ catalysts in a tubular reactor. At 1023 K with GHSV 2000 h⁻¹ and S/C ratio 2.5, CH₄ conversion and H₂ yield were 96.7% and 3.16 mol per mole of CH₄ input for Pd–Rh/metal foam, better than the alumina-supported catalysts. In 200 h stability test, Pd–Rh/metal foam catalyst exhibited steady activity. Pd–Rh/metal foam catalyst performed efficiently in a heat exchanger platform reactor to be used as prototype SOFC fuel processor: at 983 K with GHSV 1200 h⁻¹ and S/C ratio 2.5, CH₄ conversion was nearly the same as that in the tubular reactor, except for more H₂ and CO₂ yields. Used Pd–Rh/metal foam catalyst was characterized by SEM, TEM, BET and CO chemisorption measurements, which provided evidence for thermal stability of the catalyst.     

Metal precursor impregnation sequence effect on the structure and performance of NiCo/MgO catalyst

The influence of metal precursor impregnation sequence has been analyzed in terms of catalytic activity and stability of NiCo/MgO catalysts for coke oven gas reforming of carbon dioxide. It is found that the metal precursor impregnation sequence overwhelmingly affected the interaction among Ni, Co and MgO and resulted in different CO₂ sorption capacity. Compared to the catalysts prepared by first Ni precursor impregnation (Co/Ni/MgO) or by simultaneous Ni and Co precursor impregnation (NiCo/MgO), the catalysts prepared by first Co precursor impregnation (Ni/Co/MgO) obtained a stronger interaction among Ni, Co and MgO, leading to strong CO₂ adsorption, smaller Ni particle size (9.6 nm), higher metal dispersion (10.6%), lower carbon deposition (1.5 wt%) and finally resulted in a superior catalytic activity and stability for coke oven gas reforming of carbon dioxide (CH₄ and CO₂ conversion were 55 ± 1% and 80 ± 2%, respectively). We also proposed a model for the effect of metal precursor impregnation sequence on the particle distribution of Ni and Co in NiCo/MgO catalyst.     

Modification of silica supported nickel catalysts with lanthanum for stability improvement in methane reforming with CO2

Dry reforming of methane (DRM) with excessive methane composition at CH₄/CO₂ = 1.2:1 was studied over lanthanum modified silica supported nickel catalysts (Ni-xLa-SiO₂, x: 1, 2, 4, and 6% in the target weight percent of La). The catalysts were prepared by ammonia evaporation method. Nickel phyllosilicate and La₂O₃ were the main phases in calcined catalysts. The modification of La enhanced the formation of 1:1 and Tran-2:1 nickel-phyllosilicate. There existed an optimum content of La loading at 1.50 wt% in Ni–2La–SiO₂ which resulted in its highest reduction degree (95.3%). The catalysts with appropriate amounts of La exhibited higher amount of CO₂ adsorption and created more medium and strong base centers. The sufficient number of exposed metallic nickel sites to catalyze the reforming reaction, as well as enough medium and strong basic sites in Ni–La–SiO₂ interface to accomplish the carbon removal were two important factors to attenuate catalyst deactivation. The catalyst stability evaluated at 750 °C for 10 h followed the order: Ni–2La–SiO₂ > Ni–4La–SiO₂ > Ni–1La–SiO₂ ≈ Ni–6La–SiO₂ > Ni–SiO₂. Ni–2La–SiO₂ catalyst possessed the lowest deactivation behavior, whose CH₄ conversion dropped from 60.2 to 55.9% after 30 h operation at 750 °C, indicating its high resistance against carbon deposition and sintering.     

Effect of metal additives on the catalytic performance of Ni/Al2O3 catalyst in thermocatalytic decomposition of methane

Thermocatalytic decomposition of methane is proposed to be an economical and green method to produce CO_x-free hydrogen and carbon nanomaterial. In present work, 60 wt% Ni/Al₂O₃ catalysts with different additives (Cu, Mn, Pd, Co, Zn, Fe, Mg) were prepared by co-impregnation method to investigate promotional effects of these metal additives on the activity and stability of 60 wt% Ni/Al₂O₃ and find out a really effective promoter for decomposition of methane. The catalyst was characterized by N₂ adsorption/desorption, X-ray diffraction, scanning electron microscopy, inductively coupled plasma optical emission spectrometer and hydrogen temperature programmed reduction. While metal additives (5 wt%) were added into 60 wt% Ni/Al₂O₃, the activity stability of 60 wt% Ni/Al₂O₃ was improved and the CH₄ conversion of 60 wt% Ni/Al₂O₃ was also improved except Zn addition. Mn addition was found to improve the catalytic activity of 60 wt% Ni/Al₂O₃ significantly and the CH₄ conversion of 5 wt% Mn-60 wt% Ni/Al₂O₃ was ∼80%. Cu addition was found to remarkably improve the catalytic stability of 60 wt% Ni/Al₂O₃ and the CH₄ conversion of 5 wt% Cu-60 wt% Ni/Al₂O₃ decreased from 61% to 45% after 250 min of reaction time. Carbon nanomaterials formed in the thermocatalytic decomposition process were characterized by X-ray diffraction, scanning electron microscopy, thermal gravimetric analyzer and Raman spectroscopy. Carbon deposits consist of amorphous carbon and carbon nanofibers.     

Low-temperature catalytic conversion of greenhouse gases (CO2 and CH4) to syngas over ceria-magnesia mixed oxide supported nickel catalysts

Running dry reforming of methane (DRM) reaction at low-temperature is highly regarded to increase thermal efficiency. However, the process requires a robust catalyst that has a strong ability to activate both CH₄ and CO₂ as well as strong resistance against deactivation at the reaction conditions. Thus, this paper examines the prospect of DRM reaction at low temperature (400–600 °C) over CeO₂–MgO supported Nickel (Ni/CeO₂–MgO) catalysts. The catalysts were synthesized and characterized by XRD, N₂ adsorption/desorption, FE-SEM, H₂-TPR, and TPD-CO₂ methods. The results revealed that Ni/CeO₂–MgO catalysts possess suitable BET specific surface, pore volume, reducibility and basic sites, typical of heterogeneous catalysts required for DRM reaction. Remarkably, the activity of the catalysts at lower temperature reaction indicates the workability of the catalysts to activate both CH₄ and CO₂ at 400 °C. Increasing Ni loading and reaction temperature has gradually increased CH₄ conversion. 20 wt% Ni/CeO₂–MgO catalyst, CH₄ conversion reached 17% at 400 °C while at 900 °C it was 97.6% with considerable stability during the time on stream. Whereas, CO₂ conversions were 18.4% and 98.9% at 400 °C and 900 °C, respectively. Additionally, a higher CO₂ conversion was obtained over the catalysts with 15 wt% Ni content when the temperature was higher than 600 °C. This is because of the balance between a high number of Ni active sites and high basicity. The characterization of the used catalyst by TGA, FE-SEM and Raman Spectroscopy confirmed the presence of amorphous carbon at lower temperature reaction and carbon nanotubes at higher temperature.     

Effect of Ce on 5 wt% Ni/ZSM-5 catalysts in the CO2 reforming of CH4 reaction

The aim of this study is to investigate the promotional effect of Ce on Ni/ZSM-5 catalysts in the CO₂ reforming of CH₄ reaction. The evaluation of the catalytic performances of the composite catalysts was conducted in a fixed-bed reactor at atmospheric pressure. The influencing factors, including temperature, Ni and Ce loadings, molar feed ratio of CO₂/CH₄, and time-on-stream (TOS), were investigated. The characteristics of the catalysts were checked with Brunauer-Emmett-Teller (BET) analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM). The reduction and the basic properties of the composite catalysts were elucidated by temperature-programmed reduction by H₂ (H₂-TPR) and temperature-programmed desorption of CO₂ (CO₂-TPD), respectively. The reactivity of deposited carbon was studied by sequential temperature-programmed surface reaction of CH₄ (CH₄-TPSR) and temperature-programmed oxidation using CO₂ and O₂ (CO₂-TPO and O₂-TPO). Results indicate that higher CH₄ conversion, H₂ selectivity, and desired H₂/CO ratio for 5 wt% Ni & 5 wt% Ce/ZSM-5 could be achieved with CO₂/CH₄ feed ratio close to unity over the temperature range of 500–900 °C. Moreover, the addition of Ce could not only promote CH₄ decomposition for H₂ production but also the gasification of deposited carbon with CO₂. The dispersion of Ni particles could be improved with Ce presence as well. A partial reduction of CeO₂ to CeAlO₃ was observed from XPS spectra over 5 wt% Ni & 5 wt% Ce/ZSM-5 after H₂ reduction and 24 h CO₂–CH₄ reforming reaction. Benefiting from the introduction of 5 wt% Ce, the calculated apparent activation energies of CH₄ and CO₂ over the temperature range of 700–900 °C could be reduced by 30% and 40%, respectively.     

Light olefins synthesis from CO2 hydrogenation over mixed Fe–Co–K supported on micro-mesoporous carbon catalysts

Recycling CO₂ into light olefins is a promising approach to reduce CO₂ emissions. To promote this technology, an efficient catalyst with high activity and selectivity towards light olefins is imperative. In this work, a series of Fe–Co–K supported on micro-mesoporous carbon (MMC) and microporous carbon (MC) with different metal loading contents (20–80 wt%) were prepared for CO₂ hydrogenation to light olefins. Impregnating mixed metal oxides on both MMC and MC reduced particle sizes and enhanced their dispersion and reducibility, yielding a higher CO₂ conversion compared to the unsupported Fe–Co–K catalyst. The metal oxides were highly dispersed inside the micropores of MC support, achieving the highest CO₂ conversion. However, the high dispersion of metal oxides inside micropores led to the formation of isolated particles with a low interfacial contact with each other, resulting in a low light olefins selectivity. The MMC support provided a lower degree of metal dispersion, creating more interfacial contact area, promoting the selectivity towards olefins. Overall, the 60 wt% Fe–Co–K supported on MMC catalyst exhibited the highest light olefins yield of 10.8% at 400 °C and 20 bar and excellent stability.     

Synthesis gas production in the combined CO2 reforming with partial oxidation of methane over Ce-promoted Ni/SiO2 catalysts

A series of nickel-based catalyst supported on silica (Ni/SiO₂) with different loading of Ce/Ni (molar ratio ranging from 0.17 to 0.84) were prepared using conventional co-impregnation method and were applied to synthesis gas production in the combination of CO₂ reforming with partial oxidation of methane. Among the cerium-containing catalysts, the cerium-rich ones exhibited the higher activity and stability than the cerium-low ones. The temperature-programmed reduction (TPR) and UV–vis diffuse reflectance spectroscopy (UV–vis DRS) analysis revealed that the addition of CeO₂ reduced the chemical interaction between Ni and support, resulting in an increase in reducibility and dispersion of Ni. Over NiCe-x/SiO₂ (x = 0.17, 0.50, 0.67, 0.84) catalysts, the reduction peak in TPR profiles shifted to the higher temperature with increasing Ce/Ni molar ratio, which was attributed to the smaller metallic nickel size of the reduced catalysts. The transmission electron microscopy (TEM) and X-ray diffraction (XRD) for the post-reaction catalysts confirmed that the promoter retained the metallic nickel species and prevented the metal particle growth at high reaction temperature. The NiCe-0.84/SiO₂ catalyst with small Ni particle size exhibited the stable activity with the constant H₂/CO molar ratio of 1.2 during 6-h reaction in the combination of CO₂ reforming with partial oxidation of methane at 850 °C and atmospheric pressure.     

Alumina-supported cobalt catalysts in the hydrogenation of CO2 at atmospheric pressure

20 wt.% cobalt catalysts supported on pure and 5 wt.% silica-containing alumina have been prepared and characterized by X-Ray Diffraction, IR and DR-UV-vis-NIR spectroscopies and Field-Emission Scanning Electron Microscopy (FE-SEM). The presence of a cobalt-containing surface spinel phase Co_3-xAl_xO₄ and, for the silica-containing sample, of a segregated Co₃O₄ phase is evident. These catalysts have been tested in CO₂ hydrogenation at atmospheric pressure in steady state conditions in the temperature range 523–773 K. Both catalysts are active in CO₂ hydrogenation to methane (methanation) and to CO (reverse Water Gas Shift, rWGS). CO₂ hydrogenation activity is higher on freshly pre-reduced silica-free Co/Al₂O₃, while selectivity to methane is slightly higher on the silica-containing sample. Spent catalysts contain clustered or amorphous cobalt metal centers as active sites for methanation. The silica-containing catalyst shows slow deactivation in CO₂ hydrogenation upon 13 h experiments, with quite stable or even slightly increasing rWGS activity and decreasing CH₄ selectivity. This confirms previous data suggesting that, over cobalt catalysts, sites for methanation are metal centers prone to deactivation by carbon deposition. However, in contrast with what happens with unsupported and silica-supported cobalt catalysts, where deactivation is very fast, over these alumina-based catalysts carbon deposition and deactivation occur much more slowly. Sites for rWGS are unreduced cobalt centers which do not undergo such a deactivation phenomenon.     

Y2O3-promoted NiO/SBA-15 catalysts highly active for CO2/CH4 reforming

A series of Y₂O₃-promoted NiO/SBA-15 (9 wt% Ni) catalysts (Ni:Y weight ratio = 9:0, 3:1, 3:2, 1:1) were prepared using a sol–gel method. The fresh as well as the catalysts used in CO₂ reforming of methane were characterized using N₂-physisorption, XRD, FT-IR, XPS, UV, HRTEM, H₂-TPR, O₂-TPD and TG techniques. The results indicate that upon Y₂O₃ promotion, the Ni nanoparticles are highly dispersed on the mesoporous walls of SBA-15 via strong interaction between metal ions and the HO–Si-groups of SBA-15. The catalytic performance of the catalysts were evaluated at 700 °C during CH₄/CO₂ reforming at a gas hourly space velocity of 24 L g_cat⁻¹ h⁻¹(at 25 ^°C and 1 atm) and CH₄/CO₂molar ratio of 1. The presence of Y₂O₃ in NiO/SBA-15 results in enhancement of initial catalytic activity. It was observed that the 9 wt% Y–NiO/SBA-15 catalyst performs the best, exhibiting excellent catalytic activity, superior stability and low carbon deposition in a time on stream of 50 h.     

Catalytic CO2 reforming of CH4 over Cr-promoted Ni/char for H2 production

The objective of the study is to investigate the catalytic performance of Cr-promoted Ni/char in CO₂ reforming of CH₄ at 850 °C. The char obtained from the pyrolysis of a long-flame coal at 1000 °C was used as the support. The catalysts were prepared by incipient wetness impregnation methods with different metal precursor doping sequence. The characterization of the composite catalysts was evaluated by XRD, XPS, SEM-EDS, TEM, H₂-TPR, CO₂-TPD, CH₄-TPSR, and CO₂-TPO. The results indicate that the catalyst prepared by co-impregnation of Ni and Cr possess higher activity than those by sequential impregnation. The optimal loading of Cr on 5 wt% Ni/char is 7.8 wt‰. Moreover, the molar feed ratio of CH₄/CO₂ has a considerable effect on both the stability and the activity of Cr–Ni/char. The main effect of Cr is the great enhance of the adsorption to CO₂. It is interesting that the conversions of CH₄ and CO₂ over Cr-promoted Ni/char and Ni/char decrease initially, following by a steady rise as the reaction proceeds with time-on-stream (TOS). In addition, cyclic tests were conducted and no distinct deterioration in the catalytic performance of the catalysts was observed. On the basis of the obtained results, nickel carbide was speculated to be the active species which was formed during the CO₂ reforming of CH₄ reaction.     

Combined catalytic partial oxidation and CO2 reforming of methane over ZrO2-modified Ni/SiO2 catalysts using fluidized-bed reactor

Nickel on zirconium-modified silica was prepared and tested as a catalyst for reforming methane with CO₂ and O₂ in a fluidized-bed reactor. A conversion of CH₄ near thermodynamic equilibrium and low H₂/CO ratio (1<H₂/CO<2) were obtained without catalyst deactivation during 10 h, in a most energy efficient and safe manner. A weight loading of 5 wt% zirconium was found to be the optimum. The catalysts were characterized using X-ray diffraction (XRD), H₂-temperature reaction (H₂-TPR), CO₂-temperature desorption (CO₂-TPD) and transmission election microscope (TEM) techniques. Ni sintering was a major reason for the deactivation of pure Ni/SiO₂ catalysts, while Ni dispersed highly on a zirconium-promoted Ni/SiO₂ catalyst. The different kinds of surface Ni species formed on ZrO₂-promoted catalysts might be responsible for its high activity and good resistance to Ni sintering.     

Effect of ionic liquid in Ni/ZrO2 catalysts applied to syngas production by methane tri-reforming

This study investigates the influence of ionic liquid in morphology, acid-base properties, metal dispersion and performance of 5%Ni/ZrO₂ catalysts in the methane tri-reforming reaction. Zirconia was prepared by precipitation and the catalysts by wet impregnation. The ionic liquid modified the acid and basic character of the catalysts and positively influenced the methane tri-reforming reaction efficiency. The reaction was evaluated with synthetic biogas and with stoichiometric feed molar ratio (CH₄: CO₂: H₂O: O₂ = 1:0.5:0.5:0.1 and CH₄: CO₂: H₂O: O₂ = 1:0.33:0.33:0.16). The Ni/ZrO₂ prepared with ionic liquid exhibits promising catalytic activity and stability in methane tri-reforming at 800 °C in 4 h run, without coke formation. An increase in the reaction temperature results in an increase of hydrogen yield and the methane conversion, reaching ∼85% at 850 °C. The presented results demonstrate that the tri-reforming reaction could be used for production of syngas with H₂/CO ratio appropriate for methanol synthesis.