Photocatalytic hydrogen production from aqueous methanol solution with CuO/Al2O3/TiO2 nanocomposite

The photocatalytic hydrogen production from aqueous methanol solution was investigated with ZnO/TiO₂, SnO/TiO₂, CuO/TiO₂, Al₂O₃/TiO₂ and CuO/Al₂O₃/TiO₂ nanocomposites. A mechanical mixing method, followed by the solid-state reaction at elevated temperature, was used for the preparation of nanocomposite photocatalyst. Among these nanocomposite photocatalysts, the maximal photocatalytic hydrogen production was observed with CuO/Al₂O₃/TiO₂ nanocomposites. A variety of components of CuO/Al₂O₃/TiO₂ photocatalysts were tested for the enhancement of H₂ formation. The optimal component was 0.2 wt% CuO/0.3 wt% Al₂O₃/TiO₂. The activity exhibited approximately tenfold enhancement at the optimum loading, compared with that with pure P-25 TiO₂. Nano-sized TiO₂ photocatalytic hydrogen technology has great potential for low-cost, environmentally friendly solar-hydrogen production to support the future hydrogen economy.     

Influence of the method of synthesis on hydrogen adsorption properties of mesoporous binary B2O3/Al2O3 gel systems

Three series of binary oxide systems B₂O₃/Al₂O₃ were prepared and the effect of alumina on dispersion of boron (B₂O₃) component was investigated. The aim of the study was to achieve a maximum dispersion of B₂O₃ in the Al₂O₃ a gel matrix that would lead to increased sorption capacity on boron oxide. Many attempts were made to establish the preparation conditions that would lead to a maximum dispersion of B₂O₃ in the Al₂O₃ gel matrix needed to increase the hydrogen sorption capacity on boron oxide. The systems were characterized by X-ray diffraction, SEM, TEM and low temperature nitrogen adsorption. Hydrogen adsorption was tested in the volumetric system.Results of the study showed that the amount of hydrogen adsorbed on B₂O₃ depended not only on the surface area of the system but also on the separation of B₂O₃ domains in Al₂O₃ gel network. Irrespective of the method of synthesis of the binary oxide system, the dispersion of B₂O₃ phase reflected in the amount of hydrogen adsorbed was the highest for the systems of the lowest B/Al molar ratios studied, i.e. for B/Al = 0.25.     

Reforming of bioethanol over Ni/Al2O3 and Ni/CeZrO2/Al2O3 catalysts in supercritical water for hydrogen production

Bioethanol was reformed in supercritical water (SCW) at 500 °C and 25 MPa on Ni/Al₂O₃ and Ni/CeZrO₂/Al₂O₃ catalysts to produce high-pressure hydrogen. The results were compared with non-catalytic reactions. Under supercritical water and in a non-catalytic environment, ethanol was reformed to H₂, CO₂ and CH₄ with small amounts of CO and C2 gas and liquid products. The presence of either Ni/Al₂O₃ or Ni/CeZrO₂/Al₂O₃ promoted reactions of ethanol reforming, dehydrogenation and decomposition. Acetaldehyde produced from the decomposition of ethanol was completely decomposed into CH₄ and CO, which underwent a further water-gas shift reaction in SCW. This led to great increases in ethanol conversion and H₂ yield on the catalysts of more than 3-4 times than that of the non-catalytic condition. For the catalytic operation, adding small amounts of oxygen at oxygen to ethanol molar ratio of 0.06 into the feed improved ethanol conversion, at the expense of some H₂ oxidized to water, resulting in a slightly lower H₂ yield. The ceria-zirconia promoted catalyst was more active than the unpromoted catalyst. On the promoted catalyst, complete ethanol conversion was achieved and no coke formation was found. The ceria-zirconia promoter has important roles in improving the decomposition of acetaldehyde, the enhancement of the water-gas shift as well as the methanation reactions to give an extremely low CO yield and a tremendously high H₂/CO ratio. The SCW environment for ethanol reforming caused the transformation of gamma-alumina towards the corundum phase of the alumina support in the Ni/Al₂O₃ catalyst, but this transformation was slowed down by the presence of the ceria-zirconia promoter.     

Oxidative steam reforming of methanol over CuO/ZnO/CeO2/ZrO2/Al2O3 catalysts

The composition (CuO/ZnO/Al₂O₃ = 30/60/10) of a commercial catalyst G66B was used as a reference for designing CuO/ZnO/CeO₂/ZrO₂/Al₂O₃ catalysts for the oxidative (or combined) steam reforming of methanol (OSRM). The effects of Al₂O₃, CeO₂ and ZrO₂ on the OSRM reaction were clearly identified. CeO₂, ZrO₂ and Al₂O₃ all promoted the dispersions of CuO and ZnO in CuO/ZnO/CeO₂/ZrO₂/Al₂O₃ catalysts. Aluminum oxide lowered the reducibility of the catalyst, and weakened the OSRM reaction. Cerium oxide increased the reducibility of the catalyst, but weakened the reaction. Zirconium oxide improved the reducibility of the catalyst, and promoted the reaction. A lower CuO/ZnO ratio of the catalyst was associated with greater promotion of ZrO₂. The critical CuO/ZnO ratio for the promotion of ZrO₂ was approximately 0.75–0.8. Introducing of ZrO₂ into CuO/ZnO/Al₂O₃ also improved the stability of the catalyst. Although Al₂O₃ inhibited the OSRM reaction, a certain amount of it was required to ensure the stability and the mechanical strength of the catalysts.     

Effects of modifying Ni/Al2O3 catalyst with cobalt on the reforming of CH4 with CO2 and cracking of CH4 reactions

Alumina supported nickel (Ni/Al₂O₃), nickel–cobalt (Ni–Co/Al₂O₃) and cobalt (Co/Al₂O₃) catalysts containing 15% metal were synthesized, characterized and tested for the reforming of CH₄ with CO₂ and CH₄ cracking reactions. In the Ni–Co/Al₂O₃ catalysts Ni–Co alloys were detected and the surface metal sites decreased with decrease in Ni:Co ratio. Turnover frequencies of CH₄ were determined for both reactions. The initial turnover frequencies of reforming (TOF_DRM) for Ni–Co/Al₂O₃ were greater than that for Ni/Al₂O₃, which suggested a higher activity of alloy sites. The initial turnover frequencies for cracking (TOF_CRK) did not follow this trend. The highest average TOF_DRM, H₂:CO ratio and TOF_CRK were observed for a catalyst containing a Ni:Co ratio of 3:1. This catalyst also had the maximum carbon deposited during reforming and produced the maximum reactive carbon during cracking. It appeared that carbon was an intermediate product of reforming and the best catalyst was able to most effectively crack CH₄ and oxidize carbon to CO by CO₂.     

Al2O3-coated nanoporous TiO2 electrode for solid-state dye-sensitized solar cell

This paper reports the preparation of a core-shell nanoporous electrode consisting of an inner TiO₂ porous matrix and a thin overlayer of Al₂O₃, and its application for solid-state dye-sensitized solar cell using p-CuI as hole conductor. Al₂O₃ overlayer was coated onto TiO₂ porous film by the surface sol–gel process. The role of Al₂O₃ layer thickness on the cell performance was investigated. The solar cells fabricated from Al₂O₃-coated electrodes showed superior performance to the bare TiO₂ electrode. Under illumination of AM 1.5 simulated sunlight (89 mW/cm²), a ca. 0.19 nm Al₂O₃ overlayer increased the photo-to-electric conversion efficiency from 1.94% to 2.59%.     

Evaluation of Ni/Y2O3/Al2O3 catalysts for hydrogen production by autothermal reforming of methane

Ni/xY₂O₃–Al₂O₃ (x = 5, 10, 15, 20 wt%) catalysts were prepared by sequential impregnation synthesis. The catalytic performance for the autothermal reforming of methane was evaluated and compared with Ni/γ-Al₂O₃ catalyst. The physicochemical properties of catalysts were characterized by X-ray diffraction (XRD), Transmission electron microscope (TEM), X-Ray Photoelectron Spectrometer (XPS), Thermo Gravimetric Analyzer (TGA) and H₂-temperature programmed reduction techniques (TPR). The decrease of nickel particle size and the change of reducibility were found with Y modification. The CH₄ conversion increased with elevating levels of Y₂O₃ from 5% to 10%, then decreased with Y content from 10% to 20%. Ni/xY₂O₃–Al₂O₃ catalysts maintained high activity after 24 h on stream, while Ni/Al₂O₃ had a significant deactivation. The characterization of spent catalysts indicated that the addition of Y retarded Ni sintering and decreased the amount of coke.     

Catalytic effect of Gd2O3 and Nd2O3 on hydrogen desorption behavior of NaAlH4

This study investigated the effect of Nd₂O₃ and Gd₂O₃ as catalyst on hydrogen desorption behavior of NaAlH₄. Pressure-content-temperature (PCT) equipment measurement proved that both two oxides enhanced the dehydrogenation kinetics distinctly and increasing Nd₂O₃ and Gd₂O₃ from 0.5 mol% to 5 mol% caused a similar effect trend that the dehydrogenation amount and average dehydrogenation rate increased firstly and then decreased under the same conditions. 1 mol% Gd₂O₃–NaAlH₄ presented the largest hydrogen desorption amount of 5.94 wt% while 1 mol% Nd₂O₃–NaAlH₄ exerted the fastest dehydrogenation rate. Scanning Electron microscopy (SEM) analysis revealed that Gd₂O₃–NaAlH₄ samples displayed uniform surface morphology that was bulky, uneven and flocculent. The difference of Nd₂O₃–NaAlH₄ was that with the increasing of Nd₂O₃ content, the particles turned more and more big. Compared to dehydrogenation behavior, this phenomenon demonstrated that small particles structure were beneficial to hydrogen desorption. Besides, the further study found that different catalysts and addition amounts had different effects on the microstructure of NaAlH_4.     

A study on the stability of a NiO–CaO/Al2O3 complex catalyst by La2O3 modification for hydrogen production

This paper details the study of La₂O₃ modifications and their effect on the stability of a NiO–CaO/Al₂O₃ sorption complex catalyst used in the ReSER (reactive sorption enhanced reforming) process of hydrogen production. The La₂O₃-modified NiO–CaO/Al₂O₃ sorption complex catalyst was prepared by isometric impregnation. The microstructure, morphology and reducibility of the La₂O₃-modified sorption complex catalyst were characterized by means of BET, TEM, XRD and TPR. The stability of the catalyst used in the ReSER process was evaluated on a laboratory-scale fixed-bed reactor. Our results showed that modifying the sorption complex catalyst with La₂O₃ improved its stability up to 30 cycles of the ReSER process for hydrogen production, while only seven cycles were obtained without La₂O₃ modification. We showed that the source of the stability improvement that the La₂O₃ in the catalyst not only functioned to restrain the decrease of the support surface area and reduce the sintering of nano-CaCO₃, which could limit the decay of the sorption capacity and stability of the catalyst, but also increased the interaction between nickel oxide and the support, which improved the stability of the catalyst by increasing the dispersion of nickel grains and inhibited the growth of nickel grain size.     

Promotion of CO2 methanation activity and CH4 selectivity at low temperatures over Ru/CeO2/Al2O3 catalysts

The effect of CeO₂ loading amount of Ru/CeO₂/Al₂O₃ on CO₂ methanation activity and CH₄ selectivity was studied. The CO₂ reaction rate was increased by adding CeO₂ to Ru/Al₂O₃, and the order of CO₂ reaction rate at 250 °C is Ru/30%CeO₂/Al₂O₃ > Ru/60%CeO₂/Al₂O₃ > Ru/CeO₂ > Ru/Al₂O₃. With a decrease in CeO₂ loading of Ru/CeO₂/Al₂O₃ from 98% to 30%, partial reduction of CeO₂ surface was promoted and the specific surface area was enlarged. Furthermore, it was observed using FTIR technique that intermediates of CO₂ methanation, such as formate and carbonate species, reacted with H₂ faster over Ru/30%CeO₂/Al₂O₃ and Ru/CeO₂ than over Ru/Al₂O₃. These could result in the high CO₂ reaction rate over CeO₂-containing catalysts. As for the selectivity to CH₄, Ru/30%CeO₂/Al₂O₃ exhibited high CH₄ selectivity compared with Ru/CeO₂, due to prompt CO conversion into CH₄ over Ru/30%CeO₂/Al₂O₃.     

Influence of metal oxide on LiBH4/2LiNH2/MgH2 system for hydrogen storage properties

In this study, various nanoscale metal oxide catalysts, such as CeO₂, TiO₂, Fe₂O₃, Co₃O₄, and SiO₂, were added to the LiBH₄/2LiNH₂/MgH₂ system by using high-energy ball milling. Temperature programmed desorption and MS results showed that the Li–Mg–B–N–H/oxide mixtures were able to dehydrogenate at much lower temperatures. The order of the catalytic effect of the studied oxides was Fe₂O₃ > Co₃O₄ > CeO₂ > TiO₂ > SiO₂. The onset dehydrogenation temperature was below 70 °C for the samples doped with Fe₂O₃ and Co₃O₄ with 10 wt.%. More than 5.4 wt.% hydrogen was released at 140 °C. X-ray diffraction indicated that the addition of metal oxides inhibited the formation of Mg(NH₂)₂ during ball milling processes. It is thought that the changing of the ball milling products results from the interaction of oxide ions in metal oxide catalysts with hydrogen atoms in MgH₂. The catalytic effect depends on the activation capability of oxygen species in metal oxides on hydrogen atoms in hydrides.     

Slow interfacial charge recombination in solid-state dye-sensitized solar cell using Al2O3-coated nanoporous TiO2 films

Al₂O₃-coated TiO₂ porous films were used to fabricate solid-state dye-sensitized solar cells using CuI as hole conductor. Investigation with transient photovoltage measurements showed that the Al₂O₃ interlayer slowed down the interfacial recombination of electrons in TiO₂ with holes in CuI by forming a potential barrier at the TiO₂/CuI interface. As a consequence, the cell made from Al₂O₃-coated TiO₂ film showed superior cell performance than the cell made from TiO₂ film only, especially under relative high intensity of simulated sunlight.     

Non-thermal plasma assisted synthesis and physicochemical characterizations of Co and Cu doped Ni/Al2O3 nanocatalysts used for dry reforming of methane

Ni/Al₂O₃ nanocatalysts doped with Co and Cu were prepared by co-impregnation and modified by non-thermal plasma. The nanocatalysts were characterized by XRD, FESEM, TEM, EDX dot-mapping, BET, FTIR, TGA-DTG, and XPS analysis. According to XRD and XPS results, good interaction between active phase and support can be observed in both Ni–Co/Al₂O₃ and Ni–Cu/Al₂O₃ nanocatalysts. A uniform morphology, high surface area, and well dispersed particles of active sites in Ni–Co/Al₂O₃ nanocatalyst were observed that shows the effect of cobalt in controlling Ni ensemble size. In contrast Ni–Cu/Al₂O₃ nanocatalyst had no homogenous dispersion of active phase due to sintering of copper particles. The activity measurements illustrated better Ni–Co/Al₂O₃ nanocatalyst activity in comparison to Ni/Al₂O₃ and Ni–Cu/Al₂O₃ in terms of CH₄ and CO₂ conversion. H₂ and CO yield were higher for Ni–Co/Al₂O₃ and higher H₂/Co ratio was obtained as well. Whereas Ni/Al₂O₃ and Ni–Co/Al₂O₃ did not experience deactivation, Ni–Cu/Al₂O₃ suffered from activity loss by ca. 22% and 16% for CH₄ and CO₂ conversion, respectively. Sintering most likely happened in Ni–Cu/Al₂O₃ nanocatalyst due to high temperature of calcination while cobalt by controlling the size of Ni particles, alternated the size of active sites to a size range in which carbon formation was suppressed. Ni/Al ratio from XPS analysis which signifies Ni dispersion on alumina support was 5.15, 9.16, and 6.35 for Ni/Al₂O₃, Ni–Co/Al₂O₃, and Ni–Cu/Al₂O₃ nanocatalysts respectively. The highest ratio of Ni/Al was for Ni–Co/Al₂O₃ nanocatalyst that shows the best coverage of support by Ni active phase in this nanocatalyst.     

Selective CO oxidation on Cu promoted Pt/Al2O3 and Pt/Nb2O5 catalysts

Pt–Cu catalysts supported on Al₂O₃ and Nb₂O₅ were studied for use in selective CO oxidation. The addition of copper enhanced the activity and selectivity of Pt–Cu/Nb₂O₅ at lower temperatures when compared to Pt/Nb₂O₅. On the other hand, copper addition was not beneficial in the case of Al₂O₃ supported catalysts.     

Electrochemical and thermal characterization of AlF3-coated Li[Ni0.8Co0.15Al0.05]O2 cathode in lithium-ion cells

Li[Ni_0.8Co_0.15Al_0.05]O₂ particles are modified with AlF₃ as a new coating material. Even though the initial discharge capacity of the coated Li[Ni_0.8Co_0.15Al_0.05]O₂ is almost the same as that of the pristine material, the capacity retention and the thermal stability, in a highly oxidized state are both significantly improved. This effect is attributed to the thin AlF₃ coating layer protecting the oxidized cathode particles from attack by hydrogen fluoride in the electrolyte.     

Synthesis and dehydrogenation of LiCa(NH2)3(BH3)2

We report the synthesis of a new hydrogen storage material with a composition of LiCa(NH₂)₃(BH₃)₂. The theoretical hydrogen capacity of LiCa(NH₂)₃(BH₃)₂ is 9.85 wt.%. It can be prepared by ball milling the mixture of calcium amidoborane (Ca(NH₂BH₃)₂) and lithium amide (LiNH₂) in a molar ratio of 1:1. The experimental results show that this material starts to release hydrogen at a temperature as low as ca. 50 °C, which is ca. 70 °C lower than that of pure Ca(NH₂BH₃)₂ possibly resulting from the active interaction of NH₂⁻ in LiNH₂ with BH₃ in Ca(NH₂BH₃)₂. ca. 4.1 equiv. or 6.8 wt.% hydrogen can be released at 300 °C. The dehydrogenation is a mildly exothermic process forming stable nitride products.     

Studies on dehydrogenation characteristic of Mg(NH2)2/LiH mixture admixed with vanadium and vanadium based catalysts (V,V2O5 and VCl3)

In the present study, we have investigated the effect of vanadium and its compounds (V, V₂O₅ and VCl₃) on desorption characteristics of 1:2 magnesium amide (Mg(NH₂)₂) and lithium hydride (LiH) mixture. The hydrogen storage characteristics of 1:2 Mg(NH₂)₂/LiH mixture gets enhanced with admixing of V, V₂O₅ and VCl₃ separately. The VCl₃ has been found to be the most effective followed by V and V₂O₅. The activation energy for dehydrogenation process of 1:2 Mg(NH₂)₂/LiH mixture with and without catalyst has been evaluated using a method suggested by Ozawa et al. [25]. Based on the experimental results, schematic reaction scheme for decomposition of Mg(NH₂)₂ in the presence of VCl₃ has also been proposed.     

Destabilization effects of Mg(AlH4)2 on MgH2: Improved desorption performances and its reaction mechanism

Both kinetics and thermodynamics properties of MgH₂ are significantly improved by the addition of Mg(AlH₄)₂. The as-prepared MgH₂–Mg(AlH₄)₂ composite displays superior hydrogen desorption performances, which starts to desorb hydrogen at 90 °C, and a total amount of 7.76 wt% hydrogen is released during its decomposition. The enthalpy of MgH₂-relevant desorption is 32.3 kJ mol⁻¹ H₂ in the MgH₂–Mg(AlH₄)₂ composite, obviously decreased than that of pure MgH₂. The dehydriding mechanism of MgH₂–Mg(AlH₄)₂ composite is systematically investigated by using x-ray diffraction and differential scanning calorimetry. Firstly, Mg(AlH₄)₂ decomposes and produces active Al^∗. Subsequently, the in-situ formed Al^∗ reacts with MgH₂ and forms Mg–Al alloys. For its reversibility, the products are fully re-hydrogenated into MgH₂ and Al^∗, under 3 MPa H₂ pressure at 300 °C for 5 h.     

Stabilized zirconia-based sensor utilizing SnO2-based sensing electrode with an integrated Cr2O3 catalyst layer for sensitive and selective detection of hydrogen

A highly selective hydrogen (H₂) sensor has been successfully developed by using an yttria-stabilized zirconia (YSZ)-based mixed-potential-type sensor utilizing SnO₂ (+30 wt.% YSZ) sensing electrode (SE) with an intermediate Al₂O₃ barrier layer which was coated with a catalyst layer of Cr₂O₃. The sensor utilizing SnO₂ (+30 wt.% YSZ)-SE was found to be capable of detecting H₂ and propene (C₃H₆) sensitively at 550 °C. In order to enhance the selectivity towards H₂, a selective C₃H₆ oxidation catalyst was employed to minimize unwanted responses caused by interfering gases. Among the examined metal oxides, Cr₂O₃ facilitated the selective oxidation of C₃H₆. However, the addition or lamination of Cr₂O₃ to SnO₂ (+30 wt.% YSZ)-SE was found to diminish the sensing responses to all examined gases. Therefore, an intermediate layer of Al₂O₃ was sandwiched between the SE layer and the catalyst layer to prevent the penetration of Cr₂O₃ particles into the SE layer. The sensor using SnO₂ (+30 wt.% YSZ)-SE coated with a catalyst layer of Cr₂O₃ as well as an intermediate layer of Al₂O₃ exhibited a sensitive response toward H₂, with only minor responses toward other examined gases at 550 °C under humid conditions (21 vol.% O₂ and 1.35 vol.% H₂O in N₂ balance). A linear relationship was observed between sensitivity and H₂ concentration in the range of 20–800 ppm on a logarithmic scale. The results of sensing performance evaluation and polarization curve measurements indicate that the sensing mechanism is based on the mixed-potential model.     

Hydrogen permeation on Al2O3-based nickel/cobalt composite membranes

Al₂O₃ was synthesized using the sol-gel process with aluminum isopropoxide as the precursor and primary distilled water as the solvent. Nickel and cobalt metal powders were used to increase the strength of the membranes. The Al₂O₃-based membranes were prepared using HPS following a mechanical alloying process. The phase transformation, thermal evolution, surface and cross-section morphology of Al₂O₃ and Al₂O₃-based membranes were characterized by XRD, TG-DTA and FE-SEM. The hydrogen permeation of Al₂O₃-based membranes was examined at 300–473 K under increasing pressure. Hydrogen permeation flux through an Al₂O₃-20wt%Co membrane was obtained to 2.36 mol m⁻² s⁻¹. Reaction enthalpy was calculated to 4.5 kJ/mol using a Van’t Hoff’s plot.