Determination of Minimum Spouting Velocities in Conical Spouted Beds

Minimum spouting velocities in conical spouted beds have been obtained from pressure drops versus the superficial gas velocity curves, based on both increasing and decreasing the superficial gas velocity. It has been shown that the minimum spouting velocity from decreasing the superficial gas velocity is lower than from increasing the superficial gas velocity in most cases. This phenomenon is similar to that in conventional spouted beds and different from the early works. The experimental results also showed that there isn't significant difference in the pressure drop and U_ms under identical operating conditions between semi‐circular and circular conical spouted beds, and the same U_ms can be obtained from absolute pressure drops at any position above the gas inlet. The U_ms is found to increase with increasing the cone angle and static bed height, as well as the gas inlet diameter to a less extent.     

Hydrodynamic Characteristics of a Powder‐Particle Spouted Bed with Powder Entrained in Spouting Gas

Spouting of 3.7 mm polyvinyl chloride particles in a cone‐based cylindrical column is subjected to entrainment of FCC powder in the spouting air. It is found that the powder entrainment reduces the minimum spouting velocity, increases the bed pressure drop and reduces the maximum spoutable bed height. At any given bed height and value of U/U_ms, there is a critical value of powder loading ratio above which spouting gives way to slugging.     

Aerodynamics of a novel rotating jet spouted bed

A novel rotating jet spouted bed (RJSB) is developed and tested. It consists of a rotating air distributor with two radially located spouting air nozzles. The effects of bed height, distributor rotational speed, nozzle diameter and particle properties on the flow characteristics were examined. Various flow regimes were mapped as functions of distributor rotational speed and superficial air velocity for different materials and column dimensions. Empirical correlations were developed for the minimum spouting velocity, peak pressure drop and steady spouting pressure drop.     

Minimum spouting velocity of dense particles in shallow spouted beds

Quantitative method is used to experimentally measure the minimum spouting velocity in shallow conical spouted bed. And a new minimum spouting correlation for shallow conical spouted beds is developed. It is based on spherical ZrO₂ particles whose density is as high as 5890 kg/m³ while the other U_ms correlations published so far are mainly based on relatively deep conical beds composed of lower density particles with density around or lower than 3000 kg/m³. The new U_ms correlation can predict U_ms of heavy particles well within the range of the experimental matrix. © 2011 Canadian Society for Chemical Engineering     

加压喷动床中细颗粒喷动特性

在内径分别为 186mm和 80mm的加压喷动床中 ,以空气为喷动介质 ,在 10 1～ 70 0kPa的压力范围内考察了几种不同粒度的细颗粒在加压下的喷动特性 .研究结果表明在不同的Re_t 内压力对最小喷动速度的影响不同 .实验还发现 ,随着压力的升高 ,喷动区直径增大 ,稳定操作区域增大 ,加压可明显改善喷动床的操作稳定性     

Hydrodynamic characteristics of jet-spouted beds

Jet-spouted beds characterised by high velocity gas jets (above 1.7 U_msl), and shallow bed depths H₀ of around 2 D₁ were investigated on laboratory scale beds and industrial scale beds and the results obtained thereof are correlated and presented in this work. Compared with the classical spouted beds, important differences in bed structure, solid movements and basic hydrodynamic characteristics were observed. The minimum spouting velocity, bed voidage and pressure drop during stabilized spouting are described in terms of dimensionless equations. Bed expansion was used as the basis for the classification of different jet-spouting regimes (incoherent spouting, fast spouting, pneumatic conveying) and changes in the slope of the bed expansion curve are correlated with regime changes. This classification could be useful in the optimization of industrial scale jet-spouted beds. A typically applicable regime of fast spouting was identified.     

Spouting behaviors of binary mixtures of cylindroid and spherical particles

Spouting behaviors of cylindroid and spherical particles in a spouted bed are experimentally investigated. The characteristics of flow pattern and pressure drop of the binary mixtures are figured out and three kinds of cylindroid particles with different sizes and shapes are involved in experiments to discuss effects of particle size and shape on the spouting behaviors in beds. The emphasis is laid on the influence of the volume fraction of cylindroid particles, X_c, on the spouting phenomena, including the total pressure drop, the minimum spouting velocity, and fountain height. Results show that, the shapes and sizes of cylindroid particles, mainly including equivolume diameter and aspect ratio, significantly affect the spouting behaviors. There is a maximum volume fraction, X_c,max, for each kind of cylinders to maintain the stable fountain at a certain gas velocity. With the same gas velocity, X_c,max is lower for the cylinders with higher aspect ratio. © 2014 American Institute of Chemical Engineers AIChE J, 61: 58–67, 2015     

Prediction of pressure drop and minimum spouting velocity in draft tube conical spouted beds using genetic programming approach

The smart method of genetic programming (GP) is used to predict the operating pressure drop (ΔP_s) and the minimum spouting velocity u_ms for conical spouted beds (CSBs) equipped with nonporous draft tubes. Accordingly, six dimensionless variables have been taken as model inputs, including crucial parameters associated with the bed and tube geometric and operating conditions. Two general correlations comprising almost all constitutive and operating variables have been derived for the first time by the GP approach. Both ΔP_s and u_ms values predicted by the GP technique are in a fair agreement with the values corresponding to the experiments, with average absolute relative errors (AARE) of 18.9 and 19.9 %, respectively. The results of the proposed correlations show that the GP method is a powerful tool to make reasonable estimates.     

EFFECT OF THE PRESENCE OF PASTE IN A CONICAL SPOUTED BED DRYER WITH CONTINUOUS FEEDING

ABSTRACT

The spouted bed with inert particles has been used as a paste dryer, producing a fine powder. Few authors have studied the behavior of the bed in the presence of paste, which is important for the design of this equipment. In this work the spouting pressure drop, the minimum spouting velocity and the paste residual content in the bed were measured as a function of the feed rate. Experiments were carried out with two Newtonian pastes (egg paste and blood), a pseudoplastic one (xanthan gum suspension) and water, used as a referential material. These three types of paste behaved differently in terms of the variation of the spouting pressure drop and the minimum spouting velocity. The paste residual content in the bed was only measured with the egg paste, and in this case it increased very slightly with the feed rate, until the maximum throughput allowed by the system.     

Spouting of two-dimensional beds with draft plates

Two slotted two-dimensional spouted bed units with flexible bed dimensions were used with draft plates to study spouting pressure drop and minimum spouting superficial velocity. The data were collected while varying slant angle, spout width, separation distance, length of bed, height of bed, and size of bed (geometrical similarity) using shelled corn, soybean, and wheat. The variables which affect the spouting pressure drop and air flow through the beds are discussed. Empirical correlations are developed following the principles of dimensional analysis and similitude. The developed correlations agree closely with the collected data.     

导向管充气喷动床流体力学性能

在内径92mm的有机玻璃床内,对导向管充气喷动床的操作相图、床层压降、最小喷动速度及最大弃气速度进行了研究.实验采用4种颗粒为实验物料并采用空气为 喷动和弃气气体,通过对实验数据的回归得到用于计算或判别导向管弃气喷动床最小喷动速度和最大充气速度的计算式,以便为其设计和操作提供依据.     

Evaluation of flow regimes in a semi‐cylindrical spouted bed through statistical,mutual information,spectral and Hurst's analysis

Hydrodynamic studies were conducted in a semi‐cylindrical spouted bed column of diameter 150 mm, height 1000 mm, conical base included angle of 60° and inlet orifice diameter 25 mm. Pressure transducers at several axial positions were used to obtain pressure fluctuation time series with 1.2 and 2.4 mm glass beads at U/U_ms from 0.3 to 1.6, and static bed depths from 150 to 600 mm. The conditions covered several flow regimes (fixed bed, incipient spouting, stable spouting, pulsating spouting, slugging, bubble spouting and fluidization). Images of the system dynamics were also acquired through the transparent walls with a digital camera. The data were analyzed via statistical, mutual information theory, spectral and Hurst's Rescaled Range methods to assess the potential of these methods to characterize the spouting quality. The results indicate that these methods have potential for monitoring spouted bed operation.     

Investigation of Fluid and Coarse‐Particle Dynamics in a Two‐Dimensional Spouted Bed

The aerodynamics of particles and gas flow in a two‐dimensional spouted bed (2DSB) with draft plates is investigated with the aid of the discrete element method. The geometry of the 2DSB with draft plates is set as close as possible to the experimental apparatus of Kudra [1] and Kalwar [2]. The physical properties of the coarse particles are similar to those of shelled corn. The calculated minimum spouting velocity and pressure drop agree well with the correlations of Kudra [1] and Kalwar [2]. In the spout region, the particle vertical velocities are found to decrease as the height increases. The fluid velocity in the downcomer region decreases as the superficial gas velocity increases. The particle circulation rate increases when the friction coefficient decreases or the separation height increases. At the minimum spouting velocity, the bed height does not affect the particle circulation rate in the 2DSB with draft plates. The draft plates not only reduce the minimum spouting velocity and pressure drop but also increase the maximum spoutable bed height. The effect of taking out the draft plates on the spouting phenomenon is investigated and the effect of putting in a deflector on the possible breakage of the particles is also estimated.     

HYDRODYNAMICS AND STABILITYOF SLOT-RECTANGULAR SPOUTED BEDS. PART I: THIN BED

Spouted beds of rectangular cross-section with gas entry through bottom slots have been proposed as a means of overcoming scale-up difficulties of conventional spouted beds. A study was undertaken of bed hydrodynamics in a thin slot-rectangular column of width 150 mm and slot width 2 to 20 mm for four types of particles. Flow regimes and bed hydrodynamics are qualitatively similar to those in cylindrical spouted beds, but there are significant quantitative differences caused by the different geometry. Slot width exerts a strong influence on such features as flow regimes, maximum spoutable bed height, minimum spouting velocity, pressure drop and fountain height.     

HYDRODYNAMICS AND STABILITYOF SLOT-RECTANGULAR SPOUTED BEDS. PART I: THIN BED

Spouted beds of rectangular cross-section with gas entry through bottom slots have been proposed as a means of overcoming scale-up difficulties of conventional spouted beds. A study was undertaken of bed hydrodynamics in a thin slot-rectangular column of width 150 mm and slot width 2 to 20 mm for four types of particles. Flow regimes and bed hydrodynamics are qualitatively similar to those in cylindrical spouted beds, but there are significant quantitative differences caused by the different geometry. Slot width exerts a strong influence on such features as flow regimes, maximum spoutable bed height, minimum spouting velocity, pressure drop and fountain height.     

双喷嘴矩形喷动床流动性能实验研究

在120 mm×240 mm的双喷嘴矩形不锈钢床内,对新型双喷嘴矩形导流管喷动床的最小喷动速度和喷动高度进行了研究,考察了喷动气速、粒径、静床层高度、导流管直径、导流管安装位置对最小喷动速度和喷动高度的影响。结果表明:最小喷动速度随颗粒直径、导流管直径、导喷距的增大而增大,随静床层高度的增大而减小;喷动高度随喷动气速的增大而增大,随导流管直径的增大而减小,受静床层高度和导喷距的影响不大,并得出了最小喷动速度的关联式。     

Hydrodynamics and interphase heat transfer in a swirled spouted bed

A new modification of a spouting technique, a swirled spouted bed (SSB), is developed and proposed to increase the efficiency of heat treatment of polyfractional and fine particles and to reduce their entrainment. It is shown that under the developed spouting conditions the SSB pressure drop is 20-30% and incipient spouting velocity is 40-50% lower whereas an interphase heat transfer rate is 15-25% higher as compared to a classical spouted bed (CSB). An empirical correlation is proposed to determine the SSB pressure drop under developed conditions.     

HYDRODYNAMICS AND MASS TRANSFER IN A SPOUTED BED DRYER

ABSTRACT

The disposal of sludge generated by water treatment plants poses major financial and environmental problems. Drying of the sludge is an essential pan of any disposal process which may include incinerating, landfilling or upgrading. In the present study, experiments were carried out to investigate the drying of sludge in a spouted bed and to characterize the hydrodynamics and mass transfer mechanisms. The effect of bed moisture content on the minimum spouting velocity (U_ms) was examined for sludge granules. U_ms was found to increase with increasing the moisture content of the sludge particles. The gas phase mass transfer coefficient in the dryer was determined using porous calcined alumina particles and the results were compared with predictions by correlations available in the literature. The existing correlations gave poor predictions for the mass transfer coefficient. A new correlation for the mass transfer coefficient in a spouted bed dryer was developed based on the experimental results.     

A Discussion on Minimum Spout Velocity and Jet Penetration Length

The similarity and difference between the flat‐bottom and cone‐bottom cylindrical spouted beds, conical spouted beds and vertical upward jets in fluidized beds have been analyzed in this paper based on the effects of geometrical parameters on the minimum spouting velocity and operating stabilities of the spouted beds. The effect of angle on minimum spouting velocity was found to be only significant within the range of 30 to 60 degrees cone angles. Minimum spouting velocity in deep cylindrical spouted beds was proportional to the square root of the static bed height, but was proportional to the static bed height in conical spouted beds and large cylindrical spouted beds with small height‐to‐diameter ratio. The relationship between the minimum spouting velocity and the static bed height was consistent with that between jet velocity and the vertical jet penetration length in jetting fluidized beds.     

双喷嘴矩形喷动床中最小喷动速度的实验研究

在双喷嘴矩形喷动床内,以空气为喷动气体,研究了最小喷动速度的变化规律和影响因素。实验表明,双喷嘴矩形喷动床的最小喷动速度与颗粒粒径、床层高度及操作温度有关。并在综合考虑床层高度以及气体和固体颗粒的物性的基础上,得出了双喷嘴矩形喷动床最小喷动时雷诺数的经验关联式。