Reduction of Local Scour in the Vicinity of Bridge Pier Groups Using Collars and Riprap

The present study examines the use of independent and continuous pier collars in combination with riprap for reducing local scour around bridge pier groups. The efficiency of collars was studied through experiments. The data from the experiments were compared with data from earlier studies on single piers with collars and bridge pier groups without collars. The data showed that in the case of two piers in line, combination of continuous collars and riprap results in the most significant scour reduction of about 50 and 60% for the front and rear piers, respectively. In other cases for two piers in line, independent collars showed better efficiency than a continuous collar around both piers. It was also shown that efficiency of collars is more on a rectangular pier aligned with the flow than two piers in line. Experiments however, indicated that collars are not so effective in reduction of scouring around two transverse piers.     

Effects of Inclination of Bridge Piers on Scouring Depth

For a safe design of a bridge pier footing, it is important to estimate the maximum depth of scour as accurately as possible. The aim of this experimental study is to investigate the effects of inclination of bridge piers on local scour depths around bridge piers. Single circular piers inclined toward the downstream direction were founded in a uniform bed material. Near threshold conditions were employed. The results of this study indicate that the local scour depth decreases as the inclination of the pier increases.     

Bridge Pier Scour in Clay-Sand Mixed Sediments at Near-Threshold Velocity for Sand

Local scour at circular bridge piers embedded in a clay-sand-mixed bed was investigated in laboratory flume experiments. The effects of clay content, water content, and sand size on maximum equilibrium scour depth, equilibrium scour hole geometry, scouring process, and time variation of scour were studied at velocities close to the threshold velocities for the sand in the clay-sand mixture. It was observed that clay content and water content were the key parameters that effect the scouring process, scour hole geometry, and maximum equilibrium scour depth. The bridge pier scouring process in clay-sand mixtures involved different dominating modes for removal of sediment from scour hole: chunks-of-aggregates, aggregate-by-aggregate, and particle-by-particle. Regression-based equations for estimation of nondimensional maximum scour depth and scour hole diameter for piers embedded in clay-sand mixtures having clay content of <40% and water content of <40% were proposed as functions of pier Froude number, clay content, water content, and bed shear strength.     

Application of Riprap and Collar to Prevent Scouring around Rectangular Bridge Piers

Various methods to control scour around bridge piers have been proposed, including application of riprap and installing a collar around piers. In the present study application of riprap alone and a combination of riprap and collar were examined experimentally for scour control around rectangular bridge piers. Piers aligned with the flow and skewed at 5, 10, and 20° to the flow were tested. Piers with three different aspect ratios equal to 1:3, 1:5, and 1:7 were used in this study. A collar three times wider than the piers’ width was installed around the piers at the streambed level. All experiments were conducted at the threshold of motion of the bed material. The size and extent of stable riprap stones for prevention of scouring around the piers was found by experiment with and without the collar. A method previously given for calculating stable riprap size around circular piers is extended for rectangular piers with different aspect ratios and skew angles with and without collar protection. The extent of stable riprap layer in all tests is also presented.     

Experimental Investigation of Clear-Water Local Scour of Compound Piers

Local scour around complex piers under steady clear-water condition was studied experimentally for a variety of configuration, including different sizes and shapes of complex piers. A total of 70 experiments were carried out. Three sets of experiments were performed over the entire range of possible pile cap elevations for complex piers with different geometrical characteristics. The collected data are used to quantify the pile cap elevations that maximize or minimize the local scour depth. Some of the available methodologies to estimate the maximum local scour depth around such complex piers are evaluated. The predictions of the scour depths improved by using the revised methods of Hydraulic Engineering Circular Number 18 and Coleman.     

Design Method of Time-Dependent Local Scour at Circular Bridge Pier

A reliable prediction of local scour depth related to hydrological characteristics such as peak discharge, and time corresponding to the equilibrium scour depth is essential for the efficient design of bridge pier foundation. In this paper, a design method to predict the local scour depth with time is proposed. An experimental program was carried out using a cylindrical pier placed in uniform beds under clear-water flows. The pier scour depth was calculated on the basis of a sediment transport equation. Equilibrium local scour depth is reached when the bed-shear stress tends to critical bed-shear stress in the scour hole. Hence, changes to bed-shear stress at the circular bridge pier should be incorporated in the sediment transport theory. The proposed method follows experimental data of various sources.     

Flume Tests for Scour in Clay at Circular Piers

Local scour at circular piers founded on clay was studied experimentally in the laboratory to compare the depth of scour in sand and in clay and to investigate the effects of the Reynolds number, Froude number, and approach flow depth on scour depth. The depths of scour in front, at the side, and in the back of the piers were measured as a function of time under steady, gradually varied flow conditions. The measured scour-depth-versus-time curves were fitted with a hyperbola to estimate the equilibrium scour depths. The extrapolated equilibrium scour depths were compared with values predicted by the Federal Highway Administration equation. The results showed that although the rates of scour were much slower in clay than in sand, equilibrium scour in clay was about the same as in sand. It was found that the shape of the scour hole correlates with the pier Reynolds number. At low Reynolds numbers, the depth of scour was about the same all around the piers. At higher Reynolds numbers, the scour holes developed mainly behind the piers with much less scour in front of the piers. It was also found that the extrapolated equilibrium scour depth correlates well with the pier Reynolds number and that the Froude number and relative water depth did not have a significant effect on the scour depth for these experimental conditions.     

Control of Scour at Bridge Piers by a Downstream Bed Sill

Results are presented from laboratory experiments to investigate the effectiveness of bed sills as countermeasures against local scouring at a smooth circular bridge pier, for flow conditions near the threshold of uniform sediment motion. The bed sill was located downstream of the pier, and its effectiveness with the distance between pier and sill was evaluated. The dependence of the scour depth on different dimensionless groups was defined. The results showed that a bed sill placed at a short distance downstream of the pier reduces the scour depth, area, and volume. In particular, the smaller the distance between the two structures, the larger the effectiveness of the countermeasure. The bed sill seems to take effect some time after the beginning of the test, as the scour hole downstream of the bridge pier develops sufficiently and interacts with the countermeasure.     

Clearwater Local Scour at Complex Piers

A new methodology to predict local scour depth at a complex pier is presented herein that combines existing expressions for scouring respectively at uniform piers, caisson-founded piers, pile groups with debris rafts, and pile groups alone. The method recognises the relative scouring potentials of the components of complex piers and the transition of scouring processes occurring for varying pile-cap elevation. The validity of the method is confirmed herein using the present and also historical measurements of local scour at complex piers. The proposed methodology has the advantages of being conceptually consistent with observed scour behaviours, relatively simple to apply, applicable to wide ranges of flow and sediment conditions (through incorporation into a more general analysis framework), and applicable over the entire range of possible pile-cap elevations. For design purposes, the present method highlights respective pile-cap elevations that maximize (i.e., to be avoided over the pier life) and minimize local scour at complex piers. The present method reinforces that where the pile-cap elevation relative to the bed can vary with time at a bridge site, potential local-scour depths need to be assessed over the range of possible pile-cap elevations for the pier.     

Maximum Local Scour Depth at Bridge Piers under Unsteady Flow

The temporal effect of hydrograph on local scour depth is investigated under clear-water scour condition. By analyzing the characteristics of scour-depth evolutions at bridge piers for different rising hydrographs, a relation for estimating the maximum scour depth in uniform sediment is proposed. In the relation, the flow unsteadiness effect is taken into account by an unsteady flow parameter combining the peak-flow intensity and time-to-peak factors. For nonuniform sediment with d84 employed as the effective sediment size, this relation can yield reasonably good results of the maximum scour depth under rising hydrograph.     

Riprap Protection at Bridge Piers

Although riprap is the most commonly employed countermeasure against scouring around bridge piers, few studies exist of riprap performance under live-bed conditions. In this study, failure mechanisms, stability, and placement level effects for riprap at bridge piers are considered experimentally. Under clear-water conditions, riprap is subject to shear, winnowing, and edge failure. Under live-bed conditions, a fourth failure mechanism, destabilization by bed-form progression, becomes important. Destabilization by bed-form progression is dependent on the destabilizing influence of bed-form troughs as they pass the pier. Experiments were used to assess the ability of riprap stones to protect bridge piers under a wide range of flow conditions. The effects of placing the riprap layer at depth within the sediment bed, rather than level with the bed surface, were investigated also. The study showed that, as the flow velocity increases, the ability of riprap stones to protect a pier decreases asymptotically until the scour depth in the riprap layer reaches that of an equivalent unprotected pier. In addition, it was found that the deeper the placement level the less exposed the riprap was to destabilizing bed forms and the better the protection against local scour. Lowering the placement level also meant that the riprap performed better than for surface-placed layers as the flow velocity increased. The mode of riprap failure is also changed as the placement level below the bed surface is lowered. A pier riprap size-prediction equation is proposed, including a parameter to account for placement level.     

Clear-Water Scour at Piers in Sand Beds with an Armor Layer of Gravels

Clear-water scour at circular and square piers, embedded in a sand bed overlain by a thin armor layer of gravels, was experimentally studied. Depending on the pier width, flow depth, armor gravel, and bed-sand sizes, three cases of scour holes at piers in armored beds were recognized. A comparison of the experimental data shows that the scour depth at a pier with an armor layer under limiting stability of the surface particles is greater than that without an armor layer for the same bed sediments, if the secondary armoring formed within the scour hole is scattered. The equations of maximum equilibrium scour depths at piers in armored beds for these cases are proposed. On the other hand, the scour depth with an armor layer is less than that without an armor layer for the same bed sediments, when the scour hole is shielded by the compact secondary armor layer.     

Enhancing Utility of Submerged Vanes with Collar

Submerged vanes are submerged foils of low height and larger length, constructed in a river at an angle of attack α to the flow to modify the near-bed flow pattern and redistribute flow and sediment transport within the channel cross section. At a Froude number (F) of 0.13, the local scour development around the submerged vane without a collar was not enough to dislodge the vane whereas at F = 0.25, there was a significant local scour hole around the vane and the vane was dislodged. With the introduction of a collar at the leading edge of a submerged vane, the scour depth at the leading edge of the vane was reduced to zero. A collar of circular shape was found more suitable for a rectangular vane. Recommendations for sizing collars at two values of F are given. The optimal α for a rectangular vane with a collar was found close to 40°. The study clearly indicates the advantages of using collars in case of submerged vanes and provides insight into selection of appropriate collar shapes.     

Estimating Equilibrium Scour Depth at Cylindrical Piers in Experimental Studies

Using data from six very long experiments on local scour at single cylindrical piers, some of the existing equilibrium criteria found in the literature are assessed. It is found that common criteria, which consider scour depth increments in 24?h or the observation of horizontal plateaux in records of scour depth time evolution, can incur important errors on the equilibrium scour depth. Using some of the expressions for time evolution found in the literature to fit the experimental data and infer equilibrium scour depth through extrapolation to infinite time, it is found that the equilibrium scour depth cannot be specified, in general, for experiments shorter than one to two weeks.     

Field Measurements and Simulation of Bridge Scour Depth Variations during Floods

An understanding of bridge scour mechanisms during floods in a fluvial river is very important for cost-effective bridge foundation design. Reliable bridge scour data for flood events are limited. In this study, field experiments were performed at the Si-Lo Bridge in the lower Cho-Shui River, the longest river in Taiwan, to collect scour-depth data using a sliding magnetic collar, a steel rod, and a numbered-brick column. By separating each scour component, a methodology for simulating the temporal variations of the total scour depth under unsteady flow conditions is proposed. The proposed total-scour model integrates three scour components, namely general scour, contraction scour, and local scour. The collected field data, comprising both general scour and total scour depths, are used to validate the applicability of the proposed model. Based on the peak flow discharges during floods, a comparison of the local scour depths calculated using several commonly used equilibrium local scour formulas indicates that most equations may overestimate the local scour depth.     

Wire Gabion for Protecting Bridge Piers

As a new alternative countermeasure to riprap for scour protection around bridge piers, wire gabions were investigated experimentally for failure mechanisms, effects of significant parameters on failure and its sizing in a clear-water condition. The dominating failure mechanism was found to be a shear failure. Based on the experimental data, the controlling factors for the stability of wire gabions as a scour countermeasure at the pier are flow depth relative to pier diameter, length to thickness ratio, coverage, alignment and placement depth of wire gabions. An equation for sizing of a wire gabion is proposed in terms of Froude number and factors reflecting both the effect and limit of significant parameters. Comparison of the equation with those of ripraps shows that smaller wire gabions than ripraps provide an equivalent protection implying cost effective and improved stability.     

Influence of Wood Debris Accumulation on Bridge Pier Scour

This note deals with the influence of debris accumulation on scour around bridge piers. Clear-water experiments in different hydraulic conditions have been carried out with three wood debris shapes: rectangular, triangular, and cylindrical. A wide range of debris thickness and width were studied in order to determine their influence on the maximum scour hole depth temporal evolution. The ratio of the pier diameter to the channel width was varied between 0.05 and 0.12 with total bridge contractions up to 20%. A proposed relation presents a simple design procedure to predict the increase in scour depth, which mainly depends on the flow contraction due to the debris accumulation.     

Genetic Programming to Predict Bridge Pier Scour

Bridge-pier scour is a significant problem for the safety of bridges. Extensive laboratory and field studies have been conducted examining the effect of relevant variables. This note presents an alternative to the conventional regression-based equations (HEC-18 and regression equation developed by the writers), in the form of artificial neural networks (ANNs) and genetic programming (GP). There had been 398 data sets of field measurements that were collected from published literature and were used to train the network or evolve the program. The developed network and evolved programs were validated by using the observations that were not involved in the training. The performance of GP was found more effective when compared to regression equations and ANNs in predicting the scour depth at bridge piers.     

Local Scour and Riprap Stability at Bridge Piers in a Degrading Channel

The experimental study examines local scouring and riprap stability at bridge piers in rivers subject to bed degradation. The data show that the equilibrium bed profile associated with that with or without a pier is essentially the same, except for the obvious section around the pier. Total scour depth is shown to be the sum of bed degradation and pier scour depth. The latter can be computed from the time-average live-bed scour depth associated with the undisturbed velocity ratio before bed degradation. The experimental data also show that pier-scour depth is invariant with time, for t ≥ 24?h. In a degrading channel, riprap around a pier will eventually develop into a stable mound when the bed shear stresses reduce with bed degradation. An auxiliary test shows that the mound is very vulnerable to another designed flood flow accompanied by large dunes. This type of riprap instability may be called bed-degradation induced failure.     

New Experimental Method to Find Equilibrium Scour at Bridge Piers

A new methodology for the experimental analysis of the equilibrium scour depth at bridge piers is introduced and validated for clear-water conditions. The proposed experimental methodology determines the flow conditions for a given equilibrium scour instead of determining the equilibrium scour for given flow conditions, which is the usual practice. The basic hypothesis is that the shape of the scour hole is essentially related to the scour depth and sediment properties, but not to flow conditions. This hypothesis is checked experimentally. The proposed methodology may drastically reduce the time period required for experiments (from weeks to hours), and avoids the uncertainties due to the equilibrium scour being usually achieved asymptotically. Some preliminary results of the equilibrium scour obtained with the proposed methodology are compared to the expressions given in the literature, showing fair agreement.