改进型格尼襟翼对垂直轴风力机气动性能的影响

直线翼垂直轴风力机气动效率普遍较低,为此提出一种具有内侧、外侧、双侧格尼襟翼和凹槽格尼襟翼的翼型叶片以提升其气动性能。通过数值模拟研究6种新型叶片对垂直轴风力机风能利用率、力矩系数、流场结构和叶片切向力等气动性能的影响。结果表明：6种格尼襟翼叶片均可在一定尖速比（TSR）范围内提高风能利用率,外侧凹槽格尼襟翼最大风能利用率可提高17.92％;外侧格尼襟翼与双侧凹槽格尼襟翼相比原始叶片可有效降低风力机载荷波动并提高平均力矩系数;双侧dimple-GF可改善动态失速特性,明显抑制旋涡发展;单叶片切向力在上游区明显增大,有效提高了风力机气动性能。     

垂直轴风力机两种翼型气动性能比较研究

叶片是风力机最重要的组成部分,在不同的风能资源情况下,翼型的选择对垂直轴风力机气动特性有着重要的影响。文章分别以NACA0018翼型(对称翼型)和NACA4418翼型(非对称翼型)建立3叶片H型垂直轴风力机二维仿真模型。应用数值模拟的研究方法,从功率系数、单个叶片切向力系数等方面比较两种风力机模型在不同叶尖速比下的气动特性,并采用风洞实验数据验证了流场计算的准确性。CFD计算结果表明:在低叶尖速比下,NACA4418翼型风力机气动特性优于NACA0018翼型风力机,适用于低风速区域;在高叶尖速比下,NACA0018翼型风力机气动特性较好,适用于高风速地区。而且在高叶尖速比时,NACA0018翼型在上风区时,切向力系数平均值要高于NACA4418翼型,在下风区时,NACA418翼型切向力系数平均值高。该研究可为小型垂直轴风力机翼型的选择提供参考。     

基于复合形法的垂直轴风力机翼型优化设计

针对低速航空翼型不完全适合垂直轴风力机的问题,采用复合形法对小型垂直轴风力机常用的NACA0015翼型进行了优化设计。在复合形法优化设计过程中,选取翼型的弯度和厚度作为设计变量,以翼型最大切向力系数Ctmax和失速攻角αs的加权和作为目标函数。将XFOIL程序与Viterna-Corrignan失速后模型相结合,计算出优化前后翼型气动性能参数。结果表明,与NACAOO15翼型相比,新翼型的气动性能有了较大提高,最大升力系数增大了33.5%,失速攻角提高了3°,最大切向力系数增大了43.5%。     

新型变桨立轴风力机涡效应分析

该文旨在通过变桨来改善升力型立轴风力机叶片气动特性,提高风力机最大运行效率。针对设计尖速比下风能利用系数较低的问题,提出减小叶片小攻角范围,增大叶片大攻角工作范围,以重点改善叶片低性能区域的气动特性为出发点,提高风能利用系数新变桨思路。以采用NACA0012翼型、2 m高和2 m旋转直径的两叶片H型风力机为研究对象,从涡理论来分析和比较在最佳尖速比为5的条件下,附着涡、尾随涡、脱体涡和桨距角对攻角、切向力和功率输出的影响规律。研究结果表明:变桨后,叶片的攻角、切向力和输出功率在原最大值两侧均有明显提高,拓宽了叶片高性能的工作区域;涡系中脱体涡对叶片气动特性影响最大,其中在上盘面影响较小,在下盘面影响较大;变桨前后涡系对上盘面的差异较小,对下盘面的影响差异较明显;变桨后,下盘面的叶片的涡尾迹弯曲程度在加大。     

叶片最大厚度前部修型的垂直轴风力机气动性能

风力机叶片是使风能转化为机械能的原动机构,是风力机的重要部件,风力机风能利用系数的高低主要取决于其叶片的气动外形。保持直叶片垂直轴风力机使用的NACA0022翼型的对称性不变,改变其叶片最大厚度前部的形状,以期得到高风能利用系数的垂直轴风力机翼型。利用Fluent软件,采用k-ωSST湍流模型和SIMPLE算法,运用滑移网格技术,对由不同叶片构成的风力机进行数值计算。计算结果表明,当叶片最大厚度前部是长短轴比为3∶2的椭圆形状时,风力机的风能利用系数更高,而且处于高风能利用系数的尖速比范围更宽;在尖速比为1.72时,风能利用系数最高,为24.8%,此时的风能利用系数较基本翼型提高了28%。叶片修型提高风力机性能的物理机制是最大厚度点前移后的叶片在大攻角下的扰流流动分离强度减弱了。     

分流导叶垂直轴风力机气动性能研究

为提高垂直轴风力机气动性能,提出一种随相位角变化而改变相对夹角的分流导叶结构。以NACA0021为基础翼型,采用计算流体力学方法对分流导叶作用下垂直轴风力机风能利用系数、单叶片瞬时转矩、压力系数及速度场进行数值分析。结果表明：静态和动态分流导叶均可提高垂直轴风力机气动性能,且动态分流导叶提升效果更为显著;相较于静态分流导叶,动态分流导叶垂直轴风力机在尖速比为2.33时风能利用系数最高可提升23%,在尖速比为2.03时静态分流导叶垂直轴风力机较原始垂直轴风力机风能利用系数提高37%;分流导叶也可使最佳尖速比前移,稳定叶片转矩波动,提升垂直轴风力机的运行稳定性。     

垂直轴风力机改进翼型气动及功率特性研究

为提高垂直轴风力机的风能利用率,基于CFD数值模拟技术,分析了常用典型垂直轴风力机翼型的气动及功率特性,并以NACA0012翼型为基础对其进行改进。对比改进前后翼型表明,增大翼型厚度可降低升阻比,增大翼型弯度可增强其失速特性;厚尾缘翼型、升阻互补型翼型可分别降低翼型失速性能、增加启动力矩,其中厚尾缘翼型的H型垂直轴风力机的功率系数较大,可提高风能利用率,为翼型优化设计提供了新思路。     

兆瓦级H型垂直轴风力发电机气动设计方案的数值模拟研究

为解决兆瓦级H型垂直轴风力发电机气动设计过程中实验和数值模拟方面耗费巨大的问题,基于升力线模拟方法完成了兆瓦级H型垂直轴风力发电机的气动设计,并利用该方法研究不同垂直轴风力机翼型设计方案对整机气动性能的影响,研究结果表明:基元翼型选用NACA0015和NACA0018对称翼型能够获得更高的风能利用率;整机叶片造型方案中,前掠翼型性能优于直叶片,前掠翼型方案的最大风能利用率随掠角增大而小幅上升,完整旋转周期内的风能利用率则随掠角增加先增大后减小,且在掠角3°时可取到整体最大风能利用率;后掠翼型性能差于直叶片,风能利用系数随掠角增大而减小;前掠与后掠组合翼型方案性能稍好于直叶片,但不如前掠叶片;不同方案之间存在性能差异的原因可能在于不同翼型的叶片分离涡在竖直方向上的旋涡脱落顺序方面存在差异,其中上部较早脱落的前掠方案有助于风能利用系数提升,下部较早脱落的后掠方案则会对风能利用系数产生负面影响。     

不同小翼对H型垂直轴风力机叶片压力分布的影响

以翼型为NACA0012的单叶片H型垂直轴风力机为研究对象,采用数值模拟的研究方法,分析叶片两端未安装小翼和安装3种不同叶尖小翼对H型垂直轴风力机叶片表面压力分布和叶尖涡的影响。结果表明:安装小翼均可提高H型垂直轴风力机的最大转矩系数,其中安装Winglet可提高H型垂直轴风力机起动力矩;增加叶尖小翼均对消除叶尖涡有利;H型垂直轴风力机叶片两端安装Winglet小翼较其他两种小翼效果好。     

高效低载的三维风力机叶片外形优化设计方法

常规风力机叶片的优化设计都是从二维翼型开始的,且翼型总是以升阻比最大为优化目标。然而,二维翼型的升阻比最大和三维叶片的高风能利用率与低气动载荷有本质的不同,采用以往的叶片优化方法常常会在提高风能利用率的同时,使叶片所受的气动载荷也提高。针对这一问题,提出基于多岛遗传算法和动量叶素理论,在给定风况条件下,以加权风能利用率最高与气动载荷最小为目标函数,以叶片各个截面的翼型型线及扭角作为设计变量,对三维叶片开展多目标优化方法设计研究。并对某实际NREL Phase VI叶片进行优化设计,结果表明：在给定风况下相比原叶片,优化叶片在风能利用率提升了3.06%的基础上,叶根弯矩降低了11.68%。在变转速与变风况下,优化叶片的气动效率整体提升,叶根弯矩明显降低。     

Ash-forming elements in four Scandinavian wood species. Part 1: Summer harvest

Woody biomass in Finland and Sweden comprises mainly four wood species: spruce, pine, birch and aspen. To study the ash, which may cause problems for the combustion device, one tree of each species were cut down and prepared for comparisons with fuel samples. Well-defined samples of wood, bark and foliage were analyzed on 11 ash-forming elements: Si, Al, Fe, Ca, Mg, Mn, Na, K, P, S and Cl. The ash content in the wood tissues (0.2–0.7%) was low compared to the ash content in the bark tissues (1.9–6.4%) and the foliage (2.4–7.7%). The woods’ content of ash-forming elements was consequently low; the highest contents were of Ca (410–1340 ppm) and K (200–1310), followed by Mg (70–290), Mn (15–240) and P (0–350). Present in the wood was also Si (50–190), S (50–200) and Cl (30–110). The bark tissues showed much higher element contents; Ca (4800–19,100 ppm) and K (1600–6400) were the dominating elements, followed by Mg (210–2400), P (210–1200), Mn (110–1100) and S (310–750), but the Cl contents (40–330) were only moderately higher in the bark than in the wood. The young foliage (shoots and deciduous leaves) had the highest K (7100–25,000 ppm), P (1600–5300) and S (1100–2600) contents of all tissues, while the shoots of spruce had the highest Cl contents (820–1360) and its needles the highest Si content (5000–11,300). This paper presented a new approach in fuel characterization: the method excludes the presence of impurities, and focus on different categories of plant tissues. This made it possible to discuss the contents of ash element in a wide spectrum of fuel-types, which are of large importance for the energy production in Finland and Sweden.     

NEXT GENERATION ENGINEERED MATERIALS FOR ULTRA SUPERCRITICAL STEAM TURBINES

正1 ABSTRACT To reduce the effect of global warming on our climate,the levels of CO2emissions should be reduced.One way to do this is to increase the efficiency of electricity production from fossil fuels.This will in turn reduce the amount of CO2emissions for a given power output.Using US practice for efficiency calculations,then a move from a typical US plant running at 37%efficiency to a 760℃/38.5 MPa(1 400/5 580 psi)plant running at 48%efficiency would reduce CO2emissions by 170kg/MW.hr or 25%.     

Aerodynamic performance effects of leading-edge geometry in gas-turbine blades

The purpose of this paper is to illustrate the advantages of the direct surface-curvature distribution blade-design method, originally proposed by Korakianitis, for the leading-edge design of turbine blades, and by extension for other types of airfoil shapes. The leading edge shape is critical in the blade design process, and it is quite difficult to completely control with inverse, semi-inverse or other direct-design methods. The blade-design method is briefly reviewed, and then the effort is concentrated on smoothly blending the leading edge shape (circle or ellipse, etc.) with the main part of the blade surface, in a manner that avoids leading-edge flow-disturbance and flow-separation regions. Specifically in the leading edge region we return to the second-order (parabolic) construction line coupled with a revised smoothing equation between the leading-edge shape and the main part of the blade. The Hodson–Dominy blade has been used as an example to show the ability of this blade-design method to remove leading-edge separation bubbles in gas turbine blades and other airfoil shapes that have very sharp changes in curvature near the leading edge. An additional gas turbine blade example has been used to illustrate the ability of this method to design leading edge shapes that avoid leading-edge separation bubbles at off-design conditions. This gas turbine blade example has inlet flow angle 0°, outlet flow angle −64.3°, and tangential lift coefficient 1.045, in a region of parameters where the leading edge shape is critical for the overall blade performance. Computed results at incidences of −10°,   −5°,   +5°,   +10° are used to illustrate the complete removal of leading edge flow-disturbance regions, thus minimizing the possibility of leading-edge separation bubbles, while concurrently minimizing the stagnation pressure drop from inlet to outlet. These results using two difficult example cases of leading edge geometries illustrate the superiority and utility of this blade-design method when compared with other direct or inverse blade-design methods.     

Hydrogen production by steam-gasification of carbonaceous materials using concentrated solar energy – V. Reactor modeling,optimization, and scale-up

A chemical reactor for the steam-gasification of carbonaceous particles (e.g. coal, coke) is considered for using concentrated solar radiation as the energy source of high-temperature process heat. A two-phase reactor model that couples radiative, convective, and conductive heat transfer to the chemical kinetics is applied to optimize the reactor geometrical configuration and operational parameters (feedstock's initial particle size, feeding rates, and solar power input) for maximum reaction extent and solar-to-chemical energy conversion efficiency of a 5 kW prototype reactor and its scale-up to 300 kW. For the 300 kW reactor, complete reaction extent is predicted for an initial feedstock particle size up to 35 μm at residence times of less than 10 s and peak temperatures of 1818 K, yielding high-quality syngas with a calorific content that has been solar-upgraded by 19% over that of the petcoke gasified.     

Contents in Volume 23,2014

<正>~~     

汽轮机数字电液调节系统挂闸异常的技术完善

分析了200MW汽轮机数字电液调节系统在运行中存在的挂闸异常问题,采取了相应的技术处理措施,且运行实践效果良好。     

新型高压共轨ECU升压模块的数字化开发与优化

为了提高喷油器电磁阀的响应速率,提出了一种基于CPLD(复杂可编程逻辑器件)应用于高压共轨ECU的数字升压模块。鉴于该升压电路结构参数多,其升压电压的恢复响应要求高等特征,基于Pspice建立了升压电路的仿真模型,研究了不同电路参数下升压模块的输出特性,全面优化了该升压模块的性能。结果显示,该升压模块的最大转换效率可以达90%以上。在柴油发动机上对ECU的试验表明,升压电压最大波动不超过10%,其恢复时间仅为1.3ms,功率管最大温升仅为41℃,满足整机运行范围内ECU的需求。     

Trace metal chemistry and silicification of microorganisms in geothermal sinter, Taupo Volcanic Zone, New Zealand

As part of a pilot study investigating the role of microorganisms in the immobilisation of As, Sb, B, Tl and Hg, the inorganic geochemistry of seven different active sinter deposits and their contact fluids were characterised. A comprehensive series of sequential extractions for a suite of trace elements was carried out on siliceous sinter and a mixed silica-carbonate sinter. The extractions showed whether metals were loosely exchangeable or bound to carbonate, oxide, organic or crystalline fractions. Hyperthermophilic microbial communities associated with sinters deposited from high temperature (92–94°C) fluids at a variety of geothermal sources were investigated using SEM. The rapidity and style of silicification of the hyperthermophiles can be correlated with the dissolved silica content of the fluid. Although high concentrations of Hg and Tl were found associated with the organic fraction of the sinters, there was no evidence to suggest that any of the heavy metals were associated preferentially with the hyperthermophiles at the high temperature (92–94°C) ends of the terrestrial thermal spring ecosystems studied.     

Assessment methods of material ageing using Sdobyrev''s creep rupture model

The physical aspects of the activation energy, in higher and high temperatures, of the metal creep process were examined. The research results of creep-rupture in a uniaxial stress state and the criterion of creep-rupture in biaxial stress states, at two temperatures, are then presented. For these studies creep-rupture, taking case iron as an example the energy and pseudoenergy activation was determined. For complex stress states the criterion of creep-rupture was taken to be Sdobyrev's, i.e. σ_red = σ₁ β + (1 − β)σ_i, where: σ₁-maximal principal stress, σ_i-stress intensity, β-material constant (at variable temperature β = β(T)). The methods of assessment of the material ageing grade are given in percentages of ageing of new material in the following mechanical properties: 1) creep strength in uniaxial stress state, 2) activation energy in uniaxial stress state, 3) criterion creep strength in complex stress states, 4) activation pseudoenergy in complex stress states. The methods 1) and 3) are the relatively simplest because they result from experimental investigations only at nominal temperature of the structure work, however, for methods 2) and 4) it is necessary to perform the experimental investigations at least at two temperatures.     

Production of hydrogen from sewage biosolids in a continuously fed bioreactor: Effect of hydraulic retention time and sparging

Hydrogen was produced from primary sewage biosolids via mesophilic anaerobic fermentation in a continuously fed bioreactor. Prior to fermentation the sewage biosolids were heated to 70 °C for 1 h to inactivate methanogens and during fermentation a cellulose degrading enzyme was added to improve substrate availability. Hydraulic retention times (HRT) of 18, 24, 36 and 48 h were evaluated for the duration of hydrogen production. Without sparging a hydraulic retention time of 24 h resulted in the longest period of hydrogen production (3 days), during which a hydrogen yield of 21.9 L H₂ kg⁻¹ VS added to the bioreactor was achieved. Methods of preventing the decline of hydrogen production during continuous fermentation were evaluated. Of the techniques evaluated using nitrogen gas to sparge the bioreactor contents proved to be more effective than flushing just the headspace of the bioreactor. Sparging at 0.06 L L min⁻¹ successfully prevented a decline in hydrogen production and resulted in a yield of 27.0  L H₂ kg⁻¹ VS added, over a period of greater than 12 days or 12 HRT. The use of sparging also delayed the build up of acetic acid in the bioreactor, suggesting that it serves to inhibit homoacetogenesis and thus maintain hydrogen production.