Mechanical properties and creep resistance in polystyrene/polyethylene blends

Recycled plastics, predominantly high‐density polyethylene (PE), are being processed in the shape of dimension lumber and marketed as “plastic lumber.” One drawback to these products is their low creep resistance or high creep speed. The objective of this study was to examine the feasibility of reducing the creep speed of PE‐based products by blending the PE with a lower‐creep plastic, in this case polystyrene (PS). Various blends of PE and PS were prepared in either a laboratory extruder or a bowl mixer and then compression‐molded. The mechanical properties, creep behavior, morphology, and thermal properties of extruded and compression‐molded samples were determined. The modulus of elasticity of the extruded blends could be estimated by a weighted average of PS and PE, even in the absence of a compatibilizer. Processing strongly affected the morphology and mechanical properties of the blends. For 50% PS : 50% PE blends, the stress–strain curves of the extruded samples showed PE‐like behavior, whereas those from compression‐molded samples were brittle, PS‐like curves. Flexural strength was 50% higher in the extruded samples than in those from compression molding. The creep experiments were performed in three‐point bending. Creep speed was lower in 50% PS : 50% PE and 75% PS : 25% PE blends than in pure PS. Creep speed of 75% PS : 25% PE was lowest of all the extruded blends. PE formed the continuous phase even when the PS content was as high as 50 wt %. For a 75% PS : 25% PE blend, cocontinuous phases were observed in the machine direction. A ribbonlike PS‐dispersed phase was observed in the 25% PS : 75% PE and 50% PS : 50% PE samples. Blending low‐creep‐speed PS with high‐creep‐speed PE appeared to successfully improve the performance of the final composite. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1100–1108, 2000     

Characteristics of paper mill sludge‐wood fiber‐high‐density polyethylene composites

Paper mill sludge (PMS) is a waste material from pulping. In this article it was used to replace part of a wood fiber (WF) filler to reinforce high‐density polyethylene (HDPE). The properties of the PMS/WF/HDPE composites were investigated. When half of WF was replaced with PMS, the bending strength and modulus of WF/HDPE composites decreased by 16.08% and 29.91%, respectively, but their impact strength increased by 11.31%. Dynamic mechanical analysis demonstrated that with PMS addition, the storage modulus decreased and the loss tangent increased. Although the flexural properties of the PMS/WF/HDPE composites decreased compared to WF/HDPE composite, they still had satisfactorily high strengths. The 30:30:36 PMS/WF/HDPE composite presented bending and impact strengths of 61.00 MPa and 12.11 kJ m⁻², respectively. The 50:20:26 PMS/WF/HDPE composite presented bending and impact strengths of 55.02 MPa and 10.37 kJ m⁻², respectively. Rheological test proved that substituting part of WF with PMS would not affectmanufacture processing. This study indicated that paper mill sludge could be used in wood plastic composites, which would reduce pollution from paper manufacturing. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Effects of fiber size on short‐term creep behavior of wood fiber/HDPE composites

When natural fiber‐thermoplastic composites are used in long‐term loading applications, investigating creep behavior is essential. The creep behavior of high‐density polyethylene (HDPE)‐based composites reinforced with four sizes of wood fibers (WFs) (120–80, 80–40, 40–20, and 20–10 mesh) was investigated. The instantaneous deformation and creep strain of all WF/HDPE composites increased at a fixed loading level when the temperature was increased incrementally from 25 to 85°C. At a constant loading level, composites containing the larger‐sized WFs had better creep resistance than those containing smaller‐sized fibers at all measured temperatures. The creep properties of composites with smaller‐sized WFs were more temperature‐dependent than those with larger‐sized WFs. Two creep models (Burger's model and Findley's power law model) were used to fit the measured creep data. A time–temperature superposition principle calculation was attempted for long‐term creep prediction. The Findley model fitted the composite creep curves better than the four‐element Burger's model. From the predicted creep response of the WF/HDPE composites, two groups of small fibers (120–80 and 80–40 mesh) had the lowest creep resistance over long periods of time at the reference temperature of 25°C. The largest WFs (10–20 mesh) provided the best composite creep resistance. POLYM. ENG. SCI., 55:693–700, 2015. © 2014 Society of Plastics Engineers     

Surface chemistry and mechanical property changes of wood‐flour/high‐density‐polyethylene composites after accelerated weathering

Although wood–plastic composites have become more accepted and used in recent years and are promoted as low‐maintenance, high‐durability building products, they do experience a color change and a loss in mechanical properties with accelerated weathering. In this study, we attempted to characterize the modulus‐of‐elasticity (MOE) loss of photostabilized high‐density polyethylene (HDPE) and composites of wood flour and high‐density polyethylene (WF/HDPE) with accelerated weathering. We then examined how weathering changed the surface chemistry of the composites and looked at whether or not the surface changes were related to the MOE loss. By examining surface chemistry changes, we hoped to begin to understand what caused the weathering changes. The materials were left unstabilized or were stabilized with either an ultraviolet absorber or pigment. After 1000 and 2000 h of accelerated weathering, the samples were tested for MOE loss. Fourier transform infrared (FTIR) spectroscopy was employed to monitor carbonyl and vinyl group formation at the surface. Changes in the HDPE crystallinity were also determined with FTIR techniques. It was determined that structural changes in the samples (carbonyl group formation, terminal vinyl group formation, and crystallinity changes) could not be reliably used to predict changes in MOE with a simple linear relationship. This indicated that the effects of crosslinking, chain scission, and crystallinity changes due to ultraviolet exposure and interfacial degradation due to moisture exposure were interrelated factors for the weathering of HDPE and WF/HDPE composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2263–2273, 2004     

Preparation and characterization of wood‐(nylon 12) composites

The melting temperature of nylon 12 is lower than the degradation temperature of wood, which makes the preparation of wood‐(nylon 12) composites through a regular compounding/compression molding process possible. Results indicated that wood‐(nylon 12) composites had higher modulus of rupture, higher modulus of elasticity, and higher tensile strength than nylon 12, wood‐polypropylene (PP) composites, and wood‐high density polyethylene (HDPE) composites, respectively. Wood‐(nylon 12) composites also had higher thermal stability than wood‐PP composites and wood‐HDPE composites. Acting as a nucleating agent, wood increased the crystallization temperature and the degree of crystallinity of nylon 12 in wood‐(nylon 12) composites. The superior mechanical properties of wood‐(nylon 12) composites were ascribed to the good interfacial adhesion between wood and nylon 12 and the increased transcrystallinity of nylon 12 by wood. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:270–276, 2007     

High‐density polyethylene reinforced with submicron titania particles

Submicron titania particles were prepared by means of two different synthetic procedures in order to obtain different particle size (diameter ranging from 20 to 350 nm), shapes, and morphologies (amorphous or crystalline). Titania particles were surface modified with octadecylsilane in order to improve their compatibility with respect to polymeric matrices. High‐density polyethylene (HDPE)–titania composites were prepared by melt blending by using an internal mixer. The obtained composites were mechanically characterized in quasi static and creep tensile conditions. The presence of submicron titania particles (1 %vol) led to a significant increase of elastic modulus (20–25%) with respect to the unreinforced HDPE together with a slight increase of yield stress and a decrease of ultimate elongation. An interesting reduction for both elastic and viscoelastic creep compliance components was also evidenced. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

High‐density polyethylene/cycloolefin copolymer blends. Part 1: Phase structure,dynamic mechanical,tensile, and impact properties

High‐density polyethylene (HDPE) was blended with “reinforcing” cycloolefin copolymer (COC) in order to produce polyolefin materials with increased stiffness, yield and tensile strength. Experimental data on tensile modulus E_b, creep modulus E_bcr, storage modulus E_b′, loss modulus E_b″, yield strength S_yb, and tensile strength S_ub of blends are in plausible accord with their simultaneous prediction based on a predictive format that operates with a two‐parameter equivalent box model and the data on the phase continuity of components obtained from modified equations of the percolation theory. Dependencies of these mechanical properties on blend composition indicate the critical volume fraction v_2cr = 0.16 of COC. Interfacial adhesion in the HDPE/COC blends is strong enough to transmit acting stress up to the break point. Strain at break, tensile energy to break and tensile impact strength show conspicuous drops in the interval 15–25% of COC in the blends, during which COC starts to form a co‐continuous brittle component. Further growth of COC fraction accounts for reduction of blend ultimate properties to values typical of brittle polymers. However, tensile impact strength shows a local maximum at HDPE/COC = 25/75, which probably corresponds to COC toughened with HDPE particles. POLYM. ENG. SCI. 45:817–826, 2005. © 2005 Society of Plastics Engineers     

Resistance of paper mill sludge/wood fiber/high‐density polyethylene composites to water immersion and thermotreatment

The disposal of paper mill sludge (PMS) is a difficult environmental problem. Thus, PMS has been used as a substitute for wood fiber (WF) to reinforce high‐density polyethylene (HDPE). In this study, we compared PMS–WF–HDPE composites with composites without PMS after water immersion and thermal treatment. Water immersion and thermal treatment were conducted at 25 and 70°C, respectively. The results show that the composites with PMS absorbed less water but lost more of their original flexural properties after immersion; thereby, their strength was compromised. These reduced mechanical properties could be partially restored after redrying. After the thermotreatment, the composites with added PMS lost their weight and flexural properties, whereas the composites without PMS gained flexural strength. The results show that the thermotreatment improved the impact strength of the composites when no more than one‐third of WF was replaced with PMS. Fourier transform infrared spectroscopy and energy‐dispersive X‐ray energy‐dispersive spectroscopy showed that the wood index of the PMS composite decreased more than the index of the non‐PMS composite, whereas the carbonyl index increased more. However, the PMS composite showed a lower increase in the total oxygen/carbon weight ratio. This study suggested that limited amounts of WF could be substituted with PMS to reinforce HDPE. However, WF–PMS–HDPE composites should not be used in hot, humid environments for long periods. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41655.     

Comparative mechanical,fire‐retarding,and morphological properties of high‐density polyethylene/(wood flour) composites with different flame retardants

Aluminum hydroxide, magnesium hydroxide, and 1,2‐bis(pentabromophenyl) ethane were incorporated into high‐density polyethylene (HDPE) and wood flour composites, and their mechanical properties, morphology, and fire‐retardancy performance were characterized. The addition of flame retardants slightly reduced the modulus of elasticity and modulus of rupture of composites. Morphology characterization showed reduced interfacial adhesion among wood flour, HDPE, and flame retardants in the composites compared with control composites (HDPE and wood flour composites without the addition of flame retardants). The flame retardancy of composites was improved with the addition of the flame retardants, magnesium hydroxide and 1,2‐bis(pentabromophenyl) ethane, especially 1,2‐bis(pentabromophenyl) ethane, with a significant decrease in the heat release rate and total heat release. Char residue composition and morphology, analyzed by attenuated total reflectance, Fourier‐transform infrared spectroscopy, and scanning electron microscopy, showed that the char layer was formed on the composite surface with the addition of flame retardants, which promoted the fire performance of composites. The composites with 10 wt% 1,2‐bis(pentabromophenyl) ethane had good fire performance with a continuous and compact char layer on the composite surface. J. VINYL ADDIT. TECHNOL., 24:3–12, 2018. © 2015 Society of Plastics Engineers     

Wood‐thermoplastic composites from wood flour and high‐density polyethylene

High‐density polyethylene/wood flour (HDPE/WF) composites were prepared by a twin‐screw extruder. The effects of WF, silane coupling agents, polymer compatibilizers, and their content on the comprehensive properties of the WF/HDPE composites have been studied in detail, including the mechanical, thermal, and rheological properties and microstructure. The results showed that both silane coupling agents and polymer compatibilizers could improve the interfacial adhesion between WF and HDPE, and further improve the properties of WF/HDPE composites, especially with AX8900 as a compatibilizer giving higher impact strength, and with HDPE‐g‐MAH as a compatibilizer giving the best tensile and flexural properties. The resultant composite has higher strength (tensile strength = 51.03 MPa) and better heat deflection temperature (63.1°C). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of wood fibers on the rheological properties of i‐PP/wood fiber composites

The effects of wood fibers on the melt rheological behavior of isotactic poly(propylene) (i‐PP)/wood fiber (WF) composites have been studied at WF concentrations of 0–32.2 vol % at 493 K. Shear stress–shear rate variations obeyed a power law equation, and the composites exhibited shear thinning, which increased with filler content. At a low shear rate, the apparent melt viscosity increased, while melt elasticity, after an initial decrease, also increased with WF concentration. At a higher shear rate, after an initial decrease, the melt viscosity showed an increase, as did melt elasticity, with increase in filler content. A titanate coupling agent, LICA 38, used to modify the wood fiber surface, modified these rheological parameters by functioning as a plasticizer/lubricant. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 644–650, 2004     

Time–temperature superposition principle applied to a kenaf‐fiber/high‐density polyethylene composite

The time–temperature superposition principle was applied to the viscoelastic properties of a kenaf‐fiber/high‐density polyethylene (HDPE) composite, and its validity was tested. With a composite of 50% kenaf fibers, 48% HDPE, and 2% compatibilizer, frequency scans from a dynamic mechanical analyzer were performed in the range of 0.1–10 Hz at five different temperatures. Twelve‐minute creep tests were also performed at the same temperatures. Creep data were modeled with a simple two‐parameter power‐law model. Frequency isotherms were shifted horizontally and vertically along the frequency axis, and master curves were constructed. The resulting master curves were compared with an extrapolated creep model and a 24‐h creep test. The results indicated that the composite material was thermorheologically complex, and a single horizontal shift was not adequate to predict the long‐term performance of the material. This information will be useful for the eventual development of an engineering methodology for creep necessary for the design of structural building products from these composites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1995–2004, 2005     

Structure and properties of phase‐change materials based on high‐density polyethylene,hard Fischer–Tropsch paraffin wax,and wood flour

Phase‐change materials based on high‐density polyethylene (HDPE), a hard Fischer–Tropsch paraffin wax (H1 wax), and alkali‐treated wood flour (WF) were investigated. The blends and composites were prepared by melt‐mixing. They were characterized in terms of their morphology as well as thermal, mechanical, thermomechanical, and water absorption properties. Although the scanning electron microscopy micrographs showed some evidence of intimate contact between WF and the HDPE matrix, there were poor filler dispersion and interfacial adhesion. The percentage miscibility of H1 wax in HDPE seems to have decreased with increasing wax content in the blends. A fairly strong affinity between the WF and H1 wax was noticed. There was plasticization of the HDPE matrix by the wax as well as inhomogeneity and uneven wax dispersion within the polymer matrix. The presence of H1 wax and WF influenced the crystallization behavior of the HDPE matrix. The incorporation of wax reduced the thermal stability of the blends and composites, but stabilized the WF. The H1 wax and WF differently influenced the viscoelastic properties of the HDPE matrix. In contrast to the blends where the tensile properties improved in the presence of wax, the composites showed poorer properties. An increase in wax content resulted in a decrease in water uptake by the composites. POLYM. COMPOS., © 2011 Society of Plastics Engineers.     

Structure and properties of phase change materials based on HDPE,soft Fischer‐Tropsch paraffin wax,and wood flour

Phase‐change materials based on high density polyethylene (HDPE), soft Fischer‐Tropsch paraffin wax (M3), and alkali‐treated wood flour (WF) were investigated. The blend and composite samples were prepared by melt mixing using a Brabender Plastograph, followed by melt pressing. They were characterized in terms of their morphology, as well as thermal, mechanical, thermo‐mechanical, and water absorption properties. Although SEM micrographs showed some evidence of intimate contact between the WF particles and the HDPE matrix as a result of alkali treatment, poor filler dispersion, and interfacial adhesion were also observed. Partial immiscibility of the HDPE and the M3 wax was noticed, with the WF particles covered by wax. There was plasticization of the HDPE matrix by the wax, as well as partial cocrystallization, inhomogeneity and uneven wax dispersion in the polymer matrix. The HDPE/WF/M3 wax composites were more homogeneous than the blends. The presence of wax reduced the thermal stability of the blends and composites. Both the presence of M3 wax and WF influenced the viscoelastic behavior of HDPE. The HDPE/M3 wax blends showed an increase in the interfacial amorphous content as the wax content increases, which resulted in the appearance of a β‐relaxation peak. The presence of M3 wax in HDPE reduced the mechanical properties of the blends. For the composites these properties varied with WF content. An increase in wax content resulted to a decrease in water uptake by the composites, probably because the wax covered the WF particles and penetrated the pores in these particles. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Wood‐fiber/high‐density‐polyethylene composites: Compounding process

The compounding process directly influenced the compounding quality of wood–polymer blends and finally affected the interfacial bonding strength and flexural modulus of the resultant composites. With 50 wt % wood fiber, the optimum compounding parameters for the wood‐fiber/high‐density‐polyethylene blends at 60 rpm were a temperature of 180°C and a mixing time of 10 min for the one‐step process with a rotor mixer. The optimum compounding conditions at 90 rpm were a temperature of 165°C and a mixing time of 10 min. Therefore, a short compounding time, appropriate mixing temperatures, and a moderate rotation speed improved the compounding quality of the modified blends and the dynamic mechanical properties of the resultant composites. The melt torque and blend temperature followed a polynomial relationship with the loading ratio of the wood fiber. The highest melt torque and blend temperature were obtained with 50% wood fiber. The coupling treatment was effective for improving the compatibility and adhesion at the interface. The two‐step process was better than the one‐step process because the coupling agents were more evenly distributed at the interface with the two‐step process. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2570–2578, 2004     

Effect of processing method on surface and weathering characteristics of wood–flour/HDPE composites

Wood–plastic lumber is promoted as a low‐maintenance high‐durability product. When exposed to accelerated weathering, however, wood–plastic composites may experience a color change and/or loss in mechanical properties. Different methods of manufacturing wood–plastic composites lead to different surface characteristics, which can influence weathering. In this study, 50% wood–flour‐filled high‐density polyethylene (HDPE) composite samples were injection molded, extruded, or extruded and then planed, to remove the manufacturing surface characteristics. Fourier transform infrared spectroscopy was used to chemically show the difference in surface components. The samples were weathered in a xenon‐arc weathering apparatus for 1000, 2000, and 3000 h and analyzed for color fade and loss of flexural modulus of elasticity and strength. Final color (lightness) after weathering was not dependent on the manufacturing method. However, the manufacturing method was related to mechanical property loss caused by weathering. Composites with more wood component at the surface (i.e., planed samples) experienced a larger percentage of total loss in flexural modulus of elasticity and strength after weathering. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1021–1030, 2004     

Investigation into the morphology and mechanical properties of melt‐drawn filaments from uncompatibilized blends of polystyrene and high‐density polyethylene

Uncompatibilized immiscible blends of polystyrene (PS) and high‐density polyethylene (HDPE) were melt‐processed in a single‐screw extruder fitted with a fine screen mesh and capillary die and were further drawn into filaments to produce near‐nanoscale immiscible domains. The resultant morphologies and mechanical properties were studied for these structures in which load transfer is achieved solely by mechanical linkages between blend domains. The morphology of the blends revealed co‐continuity approximately in the range of 45–47 volume percent PS. The development of a three‐dimensional co‐continuous network in 45 vol% PS, as revealed by morphology observations, was also related to a decrease in extruder output rate in this region, an indicator of the melt interaction of the two phases as co‐continuity is achieved. Image analysis revealed submicron fibrillar structures near the phase inversion composition where domain sizes ranged from 6–220 nm with an average domain size of 90 nm. Tensile modulus increased with increasing PS content (E = 2.7 GPa at 47% PS) over the entire blend range with values greater than the rule of mixtures up to 50% PS. Strain to failure did not seem to be influenced by co‐continuous morphologies and the fine dispersion of PS domains appears to constrain the fundamentally high strain of HDPE. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1616–1625, 2007     

Deformation and fracture of Mg(OH)2‐filled polyolefin composites under tensile stress

The tensile behavior of high‐density polyethylene (HDPE), polypropylene (PP), and linear low‐density polyethylene composites containing a titanate coupling agent and silicone‐oil‐treated magnesium hydroxide [Mg(OH)₂] was studied. The increase in the extent of the ultimate elongation of the composites was affected by the yield stress and the strain‐hardening tendency of the polymer matrix in the composites. Ethylene–propylene–diene rubber and octane–ethylene copolymer were introduced to adjust the yield stress of PP and HDPE. Although the ultimate elongation of PP/elastomer and HDPE/elastomer blends was higher than that of virgin PP or HDPE, the ultimate elongation of the filled composites dropped at a high content of Mg(OH)₂. Scanning electron microscopy showed that the difference in the uniformity of the interface exfoliation decreased with the yield stress of the matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3248–3255, 2003     

Effects of filler–filler and polymer–filler interactions on rheological and mechanical properties of HDPE–wood composites

High‐density polyethylene (HDPE)–wood composite samples were prepared using a twin‐screw extruder. Improved filler–filler interaction was achieved by increasing the wood content, whereas improved polymer–filler interaction was obtained by adding the compatibilizer and increasing the melt index of HDPE, respectively. Then, effects of filler–filler and polymer–filler interactions on dynamic rheological and mechanical properties of the composites were investigated. The results demonstrated that enhanced filler–filler interaction induced the agglomeration of wood particles, which increased the storage modulus and complex viscosity of composites and decreased their tensile strength, elongation at break, and notched impact strength because of the stress concentration. Stronger polymer–filler interaction resulted in higher storage modulus and complex viscosity and increased the tensile and impact strengths due to good stress transfer. The main reasons for the results were analyzed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Evaluation of dynamic elastic properties of wood‐filled polypropylene composites

Dynamic modulus of elasticity (MoE) and shear modulus of wood‐filled polypropylene composite at various filler contents ranging from 10% to 50% was determined from the vibration frequencies of disc‐shaped specimens. Wood filler was used in both fiber form (pulp) and powder form (wood flour). A novel compatibilizer, m‐isopropenyl‐α,α‐dimethylbenzyl‐isocyanate(m‐TMI) grafted polypropylene with isocyanate functional group was used to prepare the composites. A linear increase in dynamic MoE, shear modulus, and density of the composite was observed with the increasing filler content. Between the two fillers, wood fiber filled composites exhibited slightly better properties. At 50% filler loading, dynamic MoE of the wood fiber filled composite was 97% higher than that of unfilled polypropylene. Halpin‐Tsai model equation was used to describe the changes in the composite modulus with the increasing filler content. The continuous improvement in elastic properties of the composites with the increasing wood filler is attributed to the effective reinforcement of low‐modulus polypropylene matrix with the high‐modulus wood filler. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1706–1711, 2006