Continuous ultrasonic devulcanization of unfilled butyl rubber

The devulcanization of resin‐cured unfilled butyl rubber with a grooved‐barrel ultrasonic reactor under various processing conditions was carried out. The experiments indicated that, because of the lower unsaturation and good thermal stability of butyl rubber, its devulcanization could be successfully accomplished only under severe ultrasonic‐treatment conditions. Gel permeation chromatography measurements were carried out for the virgin gum and sol part of devulcanized samples to study the changes in the rubber network during the devulcanization process. The obtained data showed a significant molecular weight reduction and a broadening of the molecular weight distribution upon devulcanization, which indicated that the devulcanization and degradation of butyl rubber occurred simultaneously. The rheological properties showed that devulcanized butyl rubber was more elastic than the virgin gum. The vulcanizates of the devulcanized butyl rubber showed mechanical properties comparable to those of the virgin vulcanizate. The thermal behaviors of the virgin and devulcanized butyl rubber were different and were correlated to the double‐bond content. The structural characteristics of the devulcanized butyl rubber were simulated with the Dobson–Gordon theory of rubber network statistics. A fairly good agreement between the experimental data and theoretical prediction was achieved. The simulation of devulcanized butyl rubber indicated that the rate of crosslink rupture was much higher than that of the main chain. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1316–1325, 2004     

Continuous ultrasonic devulcanization of unfilled NR vulcanizates

Sulfur-cured unfilled natural rubber (NR) is successfully devulcanized in a continuous extrusion process under the application of high-power ultrasonic energy. The die characteristics and ultrasonic power consumption are measured. A unique correlation is found between the crosslink density and gel fraction of the devulcanized NR. This correlation is independent of the processing parameters, such as barrel temperature, die gap, flow rate, and amplitude of ultrasound. However, these parameters do influence the degree of devulcanization. In most cases, the degree of devulcanization is found to pass through a maximum at an intermediate level of ultrasonic energy. It is hypothesized that simultaneous breakup and reformation of crosslinks occur during the devulcanization of NR, with the relative contribution of each being determined by the process parameters. The cure curves and mechanical properties of the revulcanized NR are studied. The mechanical properties are found to depend on the revulcanization recipe. On optimizing it, tensile strength as high as 14.2 MPa is achieved, which is about 70% of that of the virgin NR vulcanizate. Ultimate elongation as high as 670% is obtained, which is the same as that of the virgin NR vulcanizate. Such stress–strain behavior is an indication that the devulcanized NR maintains the strain-induced crystallization characteristics inherent to the virgin NR vulcanizates. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2007–2019, 1998     

Mechanochemical preparation of devulcanized ground fluoroelastomers for the enhancement of the thermal stability of nitrile–butadiene rubber vulcanizates

Mechanochemically devulcanized ground fluoroelastomer (FKM) was used as a low‐cost functional additive for the enhancement of the thermal stability of nitrile–butadiene rubber (NBR) vulcanizates. Without the use of any chemicals, the stress‐induced mechanochemical devulcanization of ground FKM was achieved through solid‐state mechanochemical milling at ambient temperature. The sol fraction of the ground FKM was increased from its original 1.4 to 19.8% after milling; this confirmed the realization of the mechanochemical devulcanization of FKM. Moreover, the oxygen‐containing polar groups on the surface of the mechanochemically milled FKM benefitted its interfacial adhesion with the polar NBR matrix. The curing characteristics and mechanical properties of the devulcanized, FKM‐filled NBR vulcanizates were investigated and compared with those of the untreated FKM‐filled NBR vulcanizates. The results show that the mechanical properties of the devulcanized FKM‐filled NBR vulcanizates were much better than those of the untreated FKM‐filled NBR vulcanizates. The presence of the reclaimed FKM significantly increased the onset degradation temperature of the NBR vulcanizates as a result of the improved polymer–filler interaction, uniform dispersion, and high thermal stability of the reclaimed FKM. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Continuous ultrasonic devulcanization of unfilled butadiene rubber

The devulcanization of sulfur‐cured unfilled butadiene rubber (BR) with a grooved‐barrel ultrasonic reactor under various processing conditions was carried out. The experiments indicated that BR had a narrow devulcanization window. Outside this window, significant degradation or no devulcanization occurred. Gel permeation chromatography (GPC) measurements were carried out with the sol part of virgin and devulcanized samples to study the breakdown of the polymeric chains. The GPC data showed a significant molecular weight reduction and a broadening of the molecular weight distribution upon devulcanization, indicating that the devulcanization and degradation of BR occurred simultaneously. The rheological properties showed that devulcanized BR was more elastic than the virgin gum. The vulcanizates of the blends of virgin and devulcanized BR showed a considerable enhancement of the mechanical properties. The thermal behaviors of the virgin and devulcanized BR were found to be different. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1166–1174, 2004     

Thiosalicylic acid as a devulcanizing agent for mechano-chemical devulcanization

A mechano-chemical devulcanization process for vulcanized natural rubber (NV) was investigated. Thiosalicylic acid was used as a test devulcanizing agent in comparison to diphenyl disulfide as the reference. The optimum condition for devulcanization of NR vulcanizates (NVs) was found to be grinding of the NV and subsequent mixing with a selected devulcanizing agent at 140°C for 30 min. The degree of devulcanization was indicated by using sol-gel fractions of the devulcanized rubber (DVR). Revulcanized rubber was made by using virgin natural rubber (NR) containing DVR at different ratios. The tensile strength of the DVR/NV composite, after revulcanization, decreased by 5–10%, while the elongation at brake was improved by 5–10% at a DVR content of 5–15%. Devulcanization of industrial truck tires, as a typical sample of industrial products, was also demonstrated for the practical application of this technique.     

The role of devulcanizing agent for mechanochemical devulcanization of styrene butadiene rubber vulcanizate

More or less universally, bis(3‐triethoxysilyl propyl) tetrasulfide (TESPT) has been used as a coupling agent during dispersion of silica filler in a virgin nonpolar rubber compound. It is for the first time that TESPT has been used as a devulcanizing agent and as‐grown devulcanized rubber facilitates the silica dispersion in nonpolar rubber compound without any coupling agent. Dual functionalities of TESPT have been modeled and validated in this work. Various factors like the role of sol‐gel content, inherent viscosity of sol rubber, crosslink density, and degree of devulcanization were investigated as a function of devulcanization time and amount of TESPT to optimize devulcanization time and TESPT amount. To study the silica reinforcement, revulcanization of devulcanized SBR was carried out with silica filler and the curing characteristics of the material were evaluated. From the mechanical properties and thermogravimetry analysis the optimum time for devulcanization is determined. Further, scanning electron microscopy (SEM) studies were undertaken to check the coherency and homogeneity of the material. POLYM. ENG. SCI., 58:74–85, 2018. © 2017 Society of Plastics Engineers     

Recycling of roofing membrane rubber by ultrasonic devulcanization

The recycling of vulcanizates based on EPDM roofing membrane rubber using a new ultrasonic devulcanization reactor with a grooved barrel was carried out. This reactor provided continuous devulcanization at an output as high as 2.52 g/s. Die pressure and ultrasonic power consumption were measured as a function of processing conditions. The mechanical properties of virgin vulcanized and revulcanized roofing membranes were measured. Tensile strength of the revulcanized rubber was found to be similar to that of the virgin vulcanizate. Gel fraction, crosslink density, and dynamic properties of the virgin vulcanizate, the ultrasonically devulcanized rubber, and the revulcanized rubber were determined. Also, dynamic properties and the cure behavior of the virgin compound and of the devulcanized roofing membrane were investigated. All these properties were found to be dependent on processing conditions during devulcanization. The thermal stability of the virgin compound, virgin vulcanizate, and devulcanized and revulcanized rubbers were studied by means of TGA. It was found that the thermal stability of all the vulcanizates in air and nitrogen environments remained practically intact, while that of devulcanized rubber in air environment was a function of processing conditions.     

Properties of natural rubber vulcanizates containing mechanochemically devulcanized ground tire rubber

The devulcanization of ground tire rubber (GTR) was carried out with a self-designed pan-mill type mechanochemical reactor. Gel fraction and crosslink density measurements confirmed the occurrence of stress induced mechanochemical devulcanization of GTR. The partially devulcanized GTR (dGTR) was blended with virgin natural rubber (NR) at different ratios. The curing characteristics and mechanical properties of these composites were investigated and compared with those composites of raw ground tire rubber (rGTR) and NR. The results showed that the tensile properties of the dGTR/NR vulcanizates were much better than those of the rGTR/NR vulcanizates, which are comparable to or even better than the virgin vulcanizate, indicating the significant benefit of mechanochemical devulcanization. At the GTR content of 10%, the tensile strength of the dGTR/NR blends increased to 23.2 MPa from 13.7 MPa of the rGTR/NR blends, enhanced by 69% through partial devulcanization of GTR, and the elongation at break increased by 47%.     

Continuous ultrasonic devulcanization of NR/SBR blends

The ultrasonic devulcanization of sulfur‐cured natural rubber (NR)/styrene–butadiene rubber (SBR) blends was studied with the goal of understanding the devulcanization of rubber vulcanizates in which two networks of different natures were present. Also, similarities and differences in the devulcanization behaviors of NR, SBR, and their blends were found. During the devulcanization of cured NR/SBR blends, we observed that, as for NR, the ultrasonic power consumption for 75/25 and 50/50 (w/w) NR/SBR blends passed through a maximum at 7.5 μm. For SBR and 25/75 (w/w) NR/SBR blends, the power consumption increased with increasing ultrasonic amplitude. The higher power consumption led to a higher degree of devulcanization. The crosslink densities of the devulcanized 25/75, 50/50, and 75/25 (w/w) NR/SBR blends were lower than those of the devulcanized NR and SBR, possibly because of the reduced degree of unsaturation. The tensile properties of the revulcanized blends were lower than those of the virgin vulcanized blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 160–168, 2002     

Devulcanization of Natural Rubber Vulcanizates by Mechanochemical Process

Using a suitable disulfide-based devulcanizing agent, which cleaved the sulfur cross-links in vulcanized rubber at high temperature, devulcanization of gum natural rubber was carried out. High sulfur and medium sulfur, as well as low sulfur–containing rubber vulcanizates were used to study the cleavage of sulfidic bonds. The cure characteristics and mechanical properties of vulcanized natural rubber and revulcanized natural rubber were studied. Thermal properties of the rubber were analyzed by thermogravimetric analysis (TGA), which indicates that the onset degradation temperature further increased on revulcanization with higher amount of disulfide. The properties of the revulcanized natural rubber increased with increasing disulfide concentration, also the mechanical properties of the devulcanized natural rubber were increased by decreasing the sulfur content in the original rubber vulcanizate. From the rheometric study increases in optimum cure time were observed when ground rubber vulcanizates were treated with higher amounts of disulfide. The scanning electronic microscopy (SEM) study suggested the change in failure mechanism as influenced by the type of cross-linking present and the devulcanizing agent used. From infrared (IR) spectroscopy it was observed that the oxidation of the main polymeric chain did not occur at the time of high temperature milling.     

Improved properties of blends of ultrasonically treated unfilled polyurethane rubber

The aim of this investigation is to improve the properties of the polyurethane rubber that has been devulcanized using the coaxial ultrasonic reactor. After devulcanization of the cured rubber under varying gap sizes and amplitudes, blends of the devulcanized and virgin rubber at different ratios are prepared. Rheological and mechanical properties, hardness as well as gel fraction and crosslink density of the vulcanized blends have been investigated. Results show that compared to the vulcanizates of the devulcanized samples, the vulcanizates of the blends show a remarkable improvement in properties, which are sometimes comparable to or even better than the virgin vulcanizate. Blends have also prepared using different proportions of ground samples and virgin rubber, and a comparison of properties between these blends and the blends of the devulcanized rubber has been carried out. The results show that compared to the ground samples, the blends of the devulcanized samples are easier to mix and exhibit enhanced and more uniform properties. Polym. Eng. Sci. 44:794–804, 2004. © 2004 Society of Plastics Engineers.     

Devulcanization of waste tires using a twin‐screw extruder: The effects of processing conditions

During recent decades, for both economic and environmental reasons, recycling of waste tires that are based on SBR/NR has been widely considered. In this study the devulcanization process of the tread section of waste tires was carried out by using a twin‐screw extruder. The effects of barrel temperature and screw speed were investigated. Percent of devulcanization, sol fraction, and curing behavior of devulcanized samples were studied. After the addition of curing agents into the devulcanizates, the general behavior of the rheometry test for rubber compounds was observed. Percent of devulcanization and sol fraction depended on the screw speed and barrel temperature, respectively. The devulcanized samples were formulated with virgin rubber (15/85 wt% ratio) and re‐cured successfully. Tensile strength, elongation at break, compression set, hardness, and resilience were evaluated. It was found that the mechanical properties of the compound containing devulcanizates were slightly inferior to those of the virgin compound. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

Friction and wear behavior of styrene butadiene rubber‐based composites reinforced with microwave‐devulcanized ground tire rubber

In this work, the tribological properties of a new material obtained by revulcanization with styrene butadiene rubber (SBR) and devulcanized ground tire rubber (GTR) were investigated. GTR was devulcanized using the microwave method at a constant power while varying the microwave exposure time. Devulcanized rubber (DV‐R) and untreated GTR were revulcanized by mixing with SBR at different rates (10, 30, 50 phr). To determine friction and wear characteristics of the samples, pin (ball) on disc and abrasion tests were conducted. Scanning electron microscopy (SEM) was employed to observe the worn surfaces of the composites to correlate the experimental test results to the wear mechanisms. All of these tests and experiments were performed on original vulcanized rubber samples for comparison. The composites exhibited different friction and wear behavior due to morphology, dispersion behavior and devulcanization functionalization of ground tire rubber. In general, DV‐R/SBR composites exhibited improvement in both mechanical and tribological properties. However, the enhanced compatibility of DV‐R resulting from the specific chemical coupling of DV‐R with SBR was crucial for the mechanical, friction and wear properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42419.     

Synergistic effect of carbon black and carbon–silica dual phase filler in natural rubber matrix

In this article, the synergistic effects of carbon black (CB) and modified carbon–silica dual phase filler (MCSDPF) on the properties of natural rubber (NR) were investigated. MCSDPF was prepared by modifying carbon–silica dual phase filler (CSDPF) with bis(3‐triethoxysilylpropyl)tetrasulphane (Si‐69). Fourier transform infrared spectroscopy and thermogravimetric analyzer analyses revealed that Si‐69 was successfully grafted to CSDPF. NR‐based compounds containing various combinations of MCSDPF and CB were prepared through a mechanical mixing. Investigations of mechanical properties, ageing resistance, abrasion resistance, dynamic mechanical properties, and morphology of tear fractured surface of MCSDPF/CB/NR vulcanizates were conducted. Our study shows that adding MCSDPF led to significant improvement in the tear resistance, fatigue life, and elongation at break of MCSDPF/CB/NR vulcanizates. Optimum stoichiometric combination of MCSDPF and CB inside the NR matrix was derived (ratio of MCSDPF and CB in wt% = 15/50), which showed synergistic effects of MCSDPF upon CB that was ultimately reflected in their tensile strength, wet skid resistance, and rolling resistance. POLYM. COMPOS., 35:1466–1472, 2014. © 2013 Society of Plastics Engineers     

Fly‐ash particles and precipitated silica as fillers in rubbers. II. Effects of silica content and Si69‐treatment in natural rubber/styrene–butadiene rubber vulcanizates

This article explored the possibility of using silica from fly‐ash particles as reinforcement in natural rubber/styrene–butadiene rubber (NR/SBR) vulcanizates. For a given silica content, the NR : SBR blend ratio of 1 : 1 (or 50 : 50 phr) exhibited the optimum mechanical properties for fly‐ash filled NR/SBR blend system. When using untreated silica from fly‐ash, the cure time and mechanical properties of the NR/SBR vulcanizates decreased with increasing silica content. The improvement of the mechanical properties was achieved by addition of Si69, the recommended dosage being 2.0 wt % of silica content. The optimum tensile strength of the silica filled NR/SBR vulcanizates was peaked at 10–20 phr silica contents. Most mechanical properties increased with thermal ageing. The addition of silica from fly‐ash in the NR/SBR vulcanizates was found to improve the elastic behavior, including compression set and resilience, as compared with that of commercial precipitated silica. Taking mechanical properties into account, the recommended dosage for the silica (FASi) content was 20 phr. For more effective reinforcement, the silica from fly‐ash particles had to be chemically treated with 2.0 wt % Si69. It was convincing that silica from fly‐ash particles could be used to replace commercial silica as reinforcement in NR/SBR vulcanizates for cost‐saving and environment benefits. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

炭黑在天然橡胶/溶聚丁苯橡胶硫化胶中的分散及其对性能的影响

考察了溶聚丁苯橡胶(SSBR)用量、炭黑的种类及用量对天然橡胶(NR)/SSBR硫化胶动态力学性能和力学性能的影响.结果表明,炭黑与SSBR的结合作用比与NR弱;随SSBR用量的增加,炭黑在NR/SSBR共混硫化胶中的分散性提高,Payne效应减弱,频率敏感性增强;随SSBR用量的增加,NR/SSBR共混硫化胶的拉伸强度和撕裂强度减小,扯断伸长率变化不大;而定伸应力则呈先减小后增大的趋势;随不同种类的炭黑在NR/SSBR硫化胶中分散性的提高,定伸应力呈上升趋势,损耗因子和压缩生热呈减小趋势.     

Comparative analysis of ultrasonically devulcanized unfilled SBR,NR, and EPDM rubbers

The comparative study of the continuous ultrasonic devulcanization of various unfilled rubbers [natural rubber, styrene–butadiene rubber (SBR), ethylene–propylene–diene rubber (EPDM)] is carried out by means of a ultrasonic reactor. The power consumption, gel fraction, crosslink density, cure behavior, and physical properties of devulcanized rubbers were measured. The glass transition temperatures of virgin, vulcanized, and devulcanized rubbers were determined in order to characterize the difference in the mobility of rubber molecules for each rubber before and after devulcanization. Thermogravimetric analysis was also used to determine thermal stability of the various rubbers. A unique correlation between gel fraction and crosslink density indicated significant differences in the efficiency of devulcanization of various rubbers. Under certain devulcanization conditions, the mechanical properties of revulcanized SBR and EPDM rubbers were found to improve compared to those of the original rubbers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 434–441, 2003     

Norbornylized soybean oil as a sustainable new plasticizer for rubbers with hybrid fillers

Carbon black (CB) and precipitated silica are two major reinforcing fillers in rubbers. CB/silica hybrid filler is also widely used in rubbers to provide balanced properties. CB/silica‐hybrid‐filler‐filled styrene‐butadiene rubber (SBR) containing naphthenic oil (NO), soybean oil (SO) and norbornylized SO (NSO) was investigated. The swelling and curing behavior and rheological, mechanical, thermal, aging and dynamic properties were studied and compared with earlier reported data on CB‐ or silica‐filled SBR. NSO provides better scorch safety and faster cure than SO. Compared with NO, the addition of SO and NSO enhances the thermal stability and aging resistance of SBR vulcanizates. SBR/NSO vulcanizates with hybrid filler exhibit a higher tensile and tear strength than SBR/NO and SBR/SO vulcanizates. A synergistic effect in the abrasion resistance of vulcanizates containing the hybrid filler is observed. An increase of sulfur content in the hybrid‐filler‐filled SBR/NSO vulcanizates provides further improvement in abrasion resistance, wet traction and rolling resistance. © 2017 Society of Chemical Industry     

Fly ash particles and precipitated silica as fillers in rubbers. I. Untreated fillers in natural rubber and styrene–butadiene rubber compounds

In this study, we investigated the effects of untreated precipitated silica (PSi) and fly ash silica (FASi) as fillers on the properties of natural rubber (NR) and styrene–butadiene rubber (SBR) compounds. The cure characteristics and the final properties of the NR and SBR compounds were considered separately and comparatively with regard to the effect of the loading of the fillers, which ranged from 0 to 80 phr. In the NR system, the cure time and minimum and maximum torques of the NR compounds progressively increased at PSi loadings of 30–75 phr. A relatively low cure time and low viscosity of the NR compounds were achieved throughout the FASi loadings used. The vulcanizate properties of the FASi‐filled vulcanizates appeared to be very similar to those of the PSi‐filled vulcanizates at silica contents of 0–30 phr. Above these concentrations, the properties of the PSi‐filled vulcanizates improved, whereas those of the FASi‐filled compounds remained the same. In the SBR system, the changing trends of all of the properties of the filled SBR vulcanizates were very similar to those of the filled NR vulcanizates, except for the tensile and tear strengths. For a given rubber matrix and silica content, the discrepancies in the results between PSi and FASi were associated with filler–filler interactions, filler particle size, and the amount of nonrubber in the vulcanizates. With the effect of the FASi particles on the mechanical properties of the NR and SBR vulcanizates considered, we recommend fly ash particles as a filler in NR at silica concentrations of 0–30 phr but not in SBR systems, except when improvement in the tensile and tear properties is required. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2119–2130, 2004     

Continuous devulcanization of waste tires by using a Co‐rotating twin screw extruder: Effects of screw configuration,temperature profile,and devulcanization agent concentration

Recently, for reasons both economical and environmental, recycling of waste tires based on (styrene butadiene rubber)/(natural rubber) (SBR/NR) has been widely considered. Response surface methodology (RSM) has been used to predict SBR/NR devulcanization behavior in a co‐rotating twin screw extruder. In this study, variable parameters were barrel temperature, screw configuration, and content of devulcanization agent. A Box‐Behnken design for the three variables, at three levels, was chosen. The sol fraction of devulcanized rubber, Δtorque (difference between maximum and minimum curing torque), and mechanical properties of revulcanizate samples were considered as the responses. The results indicated that an increase of devulcanization agent content at a certain temperature caused the sol fraction to increase. Samples including a higher sol fraction showed a lower cross‐link density. Sol fraction for high shear rate screw configuration was lower than that for other screw configurations. Tensile strength of revulcanized rubber showed a decrease with a rise of devulcanization temperature. Moreover, a relationship connecting the residence time in the extruder with stagger angle and length of different kneading blocks were obtained. J. VINYL ADDIT. TECHNOL., 19:65–72, 2013. © 2013 Society of Plastics Engineers