Single‐point determination of intrinsic viscosity of wholly aromatic thermotropic copolyesters in 1,1,1,3,3,3‐hexafluoro‐2‐propanol

A series of wholly aromatic thermotropic copolyesters based on 4‐hydroxybenzoic acid, hydroquinone, and 2,6‐naphthalene dicarboxylic acid were synthesized by direct melt polymerization with or without different added transesterification catalysts. Nine procedures for calculation of the intrinsic viscosities from a single viscosity measurement for polymer solutions, including a proposed one, were applied for the thermotropic copolyesters in 1,1,1,3,3,3‐hexafluoro‐2‐propanol at 30°C. Various forms of the Huggins and Kraemer equations, singly or combined, yielded intrinsic viscosities that were in good agreement with extrapolated values obtained in the usual manner from multipoint viscosity measurements over a wide range of concentrations. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3396–3401, 2001     

Synthesis and melt spinning of fully aromatic thermotropic liquid crystalline copolyesters containing m‐hydroxybenzoic acid units

Fibers of fully aromatic thermotropic copolyesters based on p‐acetoxybenzoic acid (p‐ABA), hydroquinone diacetate (HQDA), terephthalic acid (TPA), and m‐acetoxybenzoic acid (m‐ABA) were prepared by a high‐temperature melt‐spinning technique. Two types of the copolyesters were prepared by a high‐temperature melt polycondensation reaction using 33 mol % of kink (m‐ABA) and 67 mol % linear monomer units (p‐ABA, TPA, HQDA), and characterized by differential scanning calorimetry (DSC), polarized optical microscopy, wide‐angle X‐ray diffraction (WAXD), and intrinsic viscosity measurements. The mechanical properties and the morphology of the fibers were also determined by tensile tester, WAXD, and scanning electron microscopy (SEM). The copolyesters exhibited phase‐separated nematic liquid crystalline morphology within a broad temperature range in an isotropic matrix. DSC analysis of the copolyesters revealed broad endotherms associated with the nematic phases. The melting and spinning temperatures were in a processable region. Fibers exhibit well‐developed fibrillar structure parallel to the fiber axis. The highly oriented morphology of the fibrils is slightly dependent on the type of the linear monomer. The strength and modulus values determined for the fibers that contain equal molar composition of the linear p‐ABA, HQDA/TPA units are comparable to other reported rigid systems containing fully aromatic species. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2580–2587, 2002     

Poly(ethylene terephthalate) copolymers that contain 5‐tert‐butylisophthalic acid and 1‐3/1‐4‐cyclohexanedimethanol: Synthesis,characterization, and properties

The effects of incorporating 5‐tert‐butylisophthalic acid (^tBI) and 1‐3/1‐4 cyclohexanedimethanol (CHDM) in the polymer chain of poly(ethylene terephthalate) (PET) on the crystallization behavior and thermal, optical and tensile properties of this polyester (PETGB) were evaluated. These random copolyesters that contained between 0 and 20 mol % of CHDM and between 0 and 10 mol % of ^tBI units were prepared by esterification followed by melt copolycondensation. The compositions and molecular weights of the copolyesters were determined by ¹H‐NMR spectroscopy and viscometry, respectively. The composition of the polyester was consistent with the composition of the feed. The intrinsic viscosities of the copolymers ranged between 0.62 and 0.74 dL/g. The thermal behaviors were investigated over the entire range of copolymer compositions, using DSC under the heating and cooling rate of 20°C/min and TGA. The copolyesters with ^tBI and CHDM of < 20 mol % were crystallizable, whereas the copolyesters with ^tBI and CHDM of ≥ 20 mol % were amorphous. They appeared to be stable up to 395°C. The optical transmissions of the amorphous polyesters were more than 88% in the visible region. The mechanical behavior was investigated by performing a tensile test. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 279–285, 2007     

Nonisothermal crystallization behavior of biodegradable poly(butylene terephthalate‐co‐butylene adipate‐co‐ethylene terephthalate‐co‐ethylene adipate) copolyester

A series of biodegradable aliphatic‐aromatic copolyester, poly(butylene terephthalate‐co‐butylene adipate‐co‐ethylene terephthalate‐co‐ethylene adipate) (PBATE), were synthesized from terephthalic acid (PTA), adipic acid (AA), 1,4‐butanediol (BG) and ethylene glycol (EG) by direct esterification and polycondensation. The nonisothermal crystallization behavior of PBATE copolyesters was studied by the means of differential scanning calorimeter, and the nonisothermal crystallization kinetics were analyzed via the Avrami equation modified by Jeziorny, Ozawa analysis and Z.S. Mo method, respectively. The results show that the crystallization peak temperature of PBATE copolyesters shifted to lower temperature at higher cooling rate. The modified Avrami equation could describe the primary stage of nonisothermal crystallization of PBATE copolyesters. The value of the crystallization half‐time (t_1/2) and the crystallization parameter (Z_c) indicates that the crystallization rate of PBATE copolyesters with more PTA content was higher than that with less PTA at a given cooling rate. Ozawa analysis was not suitable to study the nonisothermal crystallization process of PBATE copolyesters, but Z.S. Mo method was successful in treatingthis process. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Synthesis and characterization of polyesters based on 1,1,1‐[bis(4‐hydroxyphenyl)‐4′‐pentadecylphenyl]ethane

Aromatic polyesters are of considerable interest because of their excellent mechanical properties, chemical resistance and thermal stability. However, most aromatic polyesters are difficult to process due to their high glass transition temperatures coupled with their insolubility in common organic solvents. The present article describes a series of organosoluble polyesters and copolyesters based on 1,1,1‐[bis(4‐hydroxyphenyl)‐4′‐pentadecylphenyl]ethane. A series of new aromatic polyesters containing pendant pentadecyl chains was synthesized by interfacial polycondensation of 1,1,1‐[bis(4‐hydroxyphenyl)‐4′‐pentadecylphenyl]ethane with terephthalic acid chloride (TPC), isophthalic acid chloride (IPC) and a mixture of TPC and IPC. A series of copolyesters was synthesized from 4,4′‐isopropylidenediphenol with TPC by incorporating 1,1,1‐[bis(4‐hydroxyphenyl)‐4′‐pentadecylphenyl]ethane as a comonomer. Inherent viscosities of the polyesters and copolyesters were in the range 0.72–1.65 dL g^?1 and number‐average molecular weights were in the range 18 170–87 220. The polyesters and copolyesters containing pendant pentadecyl chains dissolved readily in organic solvents such as chloroform, dichloromethane, pyridine and m‐cresol and could be cast into transparent, flexible and apparently tough films. Wide‐angle X‐ray diffraction data revealed the amorphous nature of the polyesters and copolyesters. The formation of loosely developed layered structure was observed due to the packing of pendant pentadecyl chains. The temperature at 10% weight loss, determined using thermogravimetric analysis in nitrogen atmosphere, of the polyesters and copolyesters containing pendant pentadecyl chains was in the range 400–460 °C. The polyesters and copolyesters exhibited glass transition temperatures in the range 63–82 °C and 177–183 °C, respectively. Copyright © 2010 Society of Chemical Industry     

Intermolecular interactions between bovine serum albumin and certain water‐soluble polymers at various temperatures

Viscometric behaviors of dextran (Dx), poly(N‐vinyl‐2‐pyrrolidone) (PVP), and poly(ethylene oxide) (PEO) with bovine serum albumin (BSA) in aqueous solutions have been studied at 25, 30, and 35°C. The reduced viscosity and intrinsic viscosity have been experimentally measured for the polymer/water and polymer/BSA/water systems by classical Huggins equation. Measurements of reduced viscosities of the Dx, PVP, and PEO in water have been calculated and all intrinsic viscosities of PEO([η]_PEO) are larger than that of Dx([η]_Dx), and PVP([η]_PVP) in aqueous solutions, at all temperatures. The intrinsic viscosities of PVP, PEO, and Dx were found to be dependent on the concentration of BSA. The presence of BSA (0.05, 0.10, and 0.30 wt %) led to a decrease in the intrinsic viscosities of polymers, at 25, 30, and 35°C. The concentration difference of BSA (Δ[BSA]) is most effective in decreasing the intrinsic viscosities of Dx at 25°C and PEO at 30 and 35°C. In other words, Δ[η] (%) order followed as Dx > PEO > PVP at 25°C and PEO > Dx > PVP at 30 and 35°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1554–1560, 2006     

Synthesis and characterization of poly(L‐lactic acid)‐b‐poly(ethylene terephthalate‐co‐sebacate)‐b‐poly(L‐lactic acid) copolyesters

Random copolyester namely, poly(ethylene terephthalate‐co‐sebacate) (PETS), with relatively lower molecular weight was first synthesized, and then it was used as a macromonomer to initiate ring‐opening polymerization of l ‐lactide. ¹H NMR quantified composition and structure of triblock copolyesters [poly(l ‐lactic acid)‐b‐poly(ethylene terephthalate‐co‐sebacate)‐b‐poly(l ‐lactic acid)] (PLLA‐PETS‐PLLA). Molecular weights of copolyesters were also estimated from NMR spectra, and confirmed by GPC. Copolyesters exhibited different solubilities according to the actual content of PLLA units in the main chain. Copolymerization effected melting behaviors significantly because of the incorporation of PETS and PLLA blocks. Crystalline morphology showed a special pattern for specimen with certain composition. It was obvious that copolyesters with more content of aromatic units of PET exhibited increased values in both of stress and modulus in tensile test. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and comparative physicochemical investigation of partly aromatic cardo copolyesters

Copolyesters were synthesized through the condensation of 0.0025 mol of 1,1′‐bis(3‐methyl‐4‐hydroxyphenyl)cyclohexane, 0.0025 mol of ethylene glycol/propylene glycol/1,4‐butanediol/1,6‐hexane diol, and 0.005 mol of terephthaloyl chloride with water/chloroform (4:1 v/v) as an interphase, 0.0125 mol of sodium hydroxide as an acid acceptor, and 50 mg of cetyl trimethyl ammonium bromide as an emulsifier. The reaction time and temperature were 2 h and 0°C, respectively. The yields of the copolyesters were 81–96%. The structures of the copolyesters were supported by Fourier transform infrared and ¹H‐NMR spectral data and were characterized with the solution viscosity and density by a floatation method (1.1011–1.2697 g/cm³). Both the intrinsic viscosity and density of the copolyesters decreased with the nature and alkyl chain length of the diol. The copolyesters possessed fairly good hydrolytic stability against water and 10% solutions of acids, alkalis, and salts at room temperature. The copolyesters possessed moderate‐to‐good tensile strength (11–37.5 MPa), good‐to‐excellent electric strength (19–45.6 kV/mm), excellent volume resistivity (3.8 × 10¹⁵ to 2.56 × 10¹⁷ Ω cm), and high glass‐transition temperatures (148–195°C) and were thermally stable up to about 408–427°C in a nitrogen atmosphere; they followed single‐step degradation kinetics involving 38–58% weight losses and 34–59% residues. The copolyesters followed 2.6–2.9‐order degradation kinetics. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and properties of copolyesters of p,p′‐bibenzoic acid,dimer acid,and alkylene glycol

Copolyesters of p,p′‐bibenzoic acid, dimer acid, and an alkylene glycol are prepared by melt polycondensation of of dimethyl p,p′‐bibenzoate, dimer acid, and an alkylene glycol. The copolyesters are characterized by the inherent viscosity, FTIR, proton NMR, DSC, polarized microscopy, and X‐ray diffraction. The polymer composition and sequence distribution of the copolyesters can be seen from the NMR spectra. The copolyesters exhibit a degree of randomness of about 1, indicating that they are random copolymers. The glass‐transition temperature (T_g) and the melting point (T_m) of the copolyesters are found from the DSC heating curves. When the content of the flexible dimer acid unit increases, the T_g of the copolyesters decreases significantly. The copolymerization effect decreases the crystallinity and the T_m of the copolyesters. It can be seen from the DSC, polarized microscopy, and X‐ray diffraction data that some copolyesters derived from 1,6‐hexanediol and 1,5‐pentanediol exhibit a monotropic smectic phase. As the molar content of the dimer acid unit increases, the isotropic–mectic transition temperature and the smectic order decreases significantly. The liquid crystallinity is completely destroyed at certain molar contents of the dimer acid unit. The smectic order of the copolyesters derived from 1,6‐hexanediol is significantly higher than that of the copolyesters derived from 1,5‐pentanediol, and it is described as an odd–even effect. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 750–758, 2003     

Fatty acid‐based comonomers as styrene replacements in soybean and castor oil‐based thermosetting polymers

In this study, a fatty acid‐based comonomer is employed as a styrene replacement for the production of triglyceride‐based thermosetting resins. Styrene is a hazardous pollutant and a volatile organic compound. Given their low volatility, fatty acid monomers, such as methacrylated lauric acid (MLA), are attractive alternatives in reducing or eliminating styrene usage. Different triglyceride‐derived cross‐linkers resins were produced for this purpose: acrylated epoxidized soybean oil (AESO), maleinated AESO (MAESO), maleinated soybean oil monoglyceride (SOMG/MA) and maleinated castor oil monoglyceride (COMG/MA). The mechanical properties of the bio‐based polymers and the viscosities of bio‐based resins were analyzed. The viscosities of the resins using MLA were higher than that of resins with styrene. Decreasing the content of MLA increased the glass transition temperature (T_g). In fact, the T_g of bio‐based resin/MLA polymers were on the order of 60°C, which was significantly lower than the bio‐based resin/styrene polymers. Ternary blends of SOMG/MA and COMG/MA with MLA and styrene improved the mechanical properties and reduced the resin viscosity to acceptable values. Lastly, butyrated kraft lignin was incorporated into the bio‐based resins, ultimately leading to improved mechanical properties of this thermoset but with unacceptable increases in viscosity. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Biodegradable polymers based on renewable resources. III. copolyesters composed of 1,4:3,6‐dianhydro‐D‐glucitol, 1,1‐bis(5‐carboxy‐2‐furyl)ethane and aliphatic dicarboxylic acid units

Various copolyesters were synthesized by bulk polycondensation of the respective combinations of 1,4;3,6‐dianhydro‐D ‐glucitol (1) as the diol component and 1,1‐bis[5‐(methoxycarbonyl)‐2‐furyl]ethane (3b) and seven dimethyl dialkanoates with methylene chain lengths of 4, 5, 6, 7, 8, 10, and 12 (4a–4g) as the dicarboxylic acid components. Most of the copolyesters were amorphous, while a copolyester composed of 1, 3b, and dodecanedioic acid (4g) (3b:4g = 25:75) units as well as homopolyesters derived from 1 and azelaic acid (4d), sebacic acid (4e), and dodecandioic acid (4g), respectively, were partially crystalline. All these homo‐ and copolyesters were soluble in chloroform, dichloromethane, pyridine, trifluoroacetic acid, and m‐cresol. The number‐average molecular weights of these polyesters were estimated to be in the range of 10,000–20,000 by SEC using chloroform as an eluent and standard polystyrene as a reference. The biodegradability of these copolyesters was assessed by enzymatic degradation using four different enzymes in a phosphate buffer solution at 37°C and by soil burial degradation tests in composted soil at 27°C. In general, biodegradability of the copolyesters decreased with increase in the difuran dicarboxylate 3b content. Copolyesters containing sebasic acid 4e units showed higher biodegradability. Soil burial degradation in the soil that was treated with antibiotics, together with electron microscopic observation, indicated that actinomycetes are mainly responsible for the degradation of the copolyesters containing 3b units in the present soil burial test. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3342–3350, 1999     

Dilute solution viscosity properties of high molar mass poly(acrylonitrile‐co‐itaconic acid)

The intrinsic viscosities [η] and viscosity constants of high molar mass poly(acrylonitrile‐co‐itaconic acid) copolymer in DMF were obtained by the methods of Huggin, Fuoss, Martin and Schulz‐Blaschke. The values of [η] by averaging procedures suggested by Sakai were close to those from Huggins method. There was an abnormal positive deviation from the rectilinearity of the reduced viscosity (η_red) versus concentration (c) plot in all the cases in the dilute regime, which was attributed to the polyelectrolytic effect. This was further confirmed by the analysis by Fuoss method. The deviation from the Huggins dependence is discussed for a good solvent (DMF) alone and in the presence of a non‐solvent, methanol. The deviation cross‐over points c′ and c″ changed with molecular weight, and the concentration range greater than c″ and less than c* was taken for a more reliable determination of intrinsic viscosity. The non‐solvent played a key role in determining the polymer–polymer interactions. The Huggins coefficient increased and the cross‐over points c′ and c″ shifted to higher concentration regime as the mixed solvent became poorer. The inter‐ and intra‐polymer interactions increased in the presence of methanol. In poor solvent, the enhanced intramolecular interactions caused the polymer to shrink in size, causing a reduction in [η] and hydrodynamic volume. Copyright © 2003 Society of Chemical Industry     

Copolyesters of hydroxyphenylalkanoic acids: synthesis and thermal properties of poly{(4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]} and poly{(3‐bromo‐4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]}

Copolyesters of 8‐(3‐hydroxyphenyl)octanoic acid (HPOA), a monomer with kink and flexible segment derived from cardanol, and 4‐hydroxybenzoic acid (HBA) or its brominated derivative, 3‐bromo‐4‐hydroxybenzoic acid (BrHBA), were synthesized by acidolysis melt polycondensation of the in situ generated acetoxyderivative in the presence of magnesium acetate as catalyst by a one‐pot method and characterized. The formation of the copolyester was confirmed by elemental analysis, FTIR and ¹H NMR spectroscopy. These polymers were highly insoluble in most solvents except highly polar solvents, such as trifluoroacetic acid. The inherent viscosities of the soluble polymers were in the range of 0.8–1.1 dlg^?1. The thermal and phase behaviour of the copolyesters were studied by DSC and polarized light microscopy. Poly{(4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]} with 50 mole% of HPOA showed a birefringent melt with opalescence and a worm‐like texture of a nematic phase. The effect of bromine substitution in the analogue poly{(3‐bromo‐4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]} was evident when it showed a lower transition with minimum 45% Br‐HBA at 225 °C showing enhanced melt processability. These copolymers, with hydrolytically degradable aliphatic carbonyl group and better crystallinity compared to poly(hydroxyalkanoate)s, are interesting in possible biomedical applications. © 2002 Society of Chemical Industry     

pH‐responsive polyzwitterions: A comparative study of acrylamide‐based polyampholyte terpolymers and polybetaine copolymers

A comparative study of pH‐responsive polyzwitterions (PZs) with polyampholyte or polybetaine architectures was conducted with well‐defined model polymer systems. Low‐charge‐density PZs, including ampholytic terpolymers composed of acrylamide (AM), sodium 3‐acrylamido‐3‐methylbutanoate, and (3‐acrylamidopropyl)trimethylammonium chloride and carboxybetaine copolymers composed of AM and 3‐(3‐acrylamidopropyldimethylammonio)propionate, were prepared via free‐radical polymerization in 0.5M NaCl to yield ter‐ and copolymers with random termonomer and comonomer distributions. Sodium formate was used as a chain‐transfer agent during the polymerizations to eliminate the effects of the monomer feed composition on the degree of polymerization (DP) and to suppress gel effects and broadening of the molecular weight distributions. The polymer compositions were determined via ¹³C‐NMR spectroscopy, and the residual counterion content was determined via elemental analysis for Na⁺ and Cl^?. The molecular weights (MWs) and polydispersity indices (PDIs) were determined via size exclusion chromatography/multi‐angle laser light scattering (SEC–MALLS); the polymer MWs ranged from 1.4 to 1.5 × 10⁶ g/mol, corresponding to DPs of 1.6–1.9 × 10⁴ repeat units, with all the polymers exhibiting PDIs less than or equal to 2.1. The intrinsic viscosities determined from SEC–MALLS data and the Flory–Fox relationship agreed with the intrinsic viscosities determined via low‐shear dilute‐solution viscometry. Data from the SEC–MALLS analysis were used to analyze the radius of gyration/molecular weight (R_g–M) relationships and the Mark–Houwink–Sakurada intrinsic viscosity/molecular weight ([η]–M) relationships for the PZs. The R_g–M and [η]–M relationships and viscometric data revealed that under size exclusion chromatography conditions, the poly[acrylamide‐co‐3‐(3‐acrylamidopropyldimethylammonio)propionate] betaine copolymers had more open, random‐coil conformations and greater polymer–solvent interactions than the ampholytic poly[acrylamide‐co‐sodium 3‐acrylamido‐3‐methylbutanoate‐co‐(3‐acrylamidopropyl)trimethylammonium chloride] terpolymers. The pH‐ and salt‐responsive dilute‐solution viscosity behavior of the PZs was examined to assess the effects of the polymer structure and composition on the solution properties. The polyampholyte terpolymers had greater solution viscosities and more pronounced stimuli‐responsiveness than the polybetaine copolymers because of their stronger intramolecular interactions and increased chain stiffness. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 24–39, 2004     

Synthesis and characterization of novel heat resistance poly(amide‐imide)s from N,N′‐[2,5‐bis(4‐aminobenzylidene) cyclopentanone] bistrimellitimide acid and various aromatic diamines

A new‐type of dicarboxylic acid was synthesized from the reaction of 2,5‐bis(4‐aminobenzylidene)cyclopentanone with trimellitic anhydride in a solution of glacial acetic acid/pyridine (Py) at refluxing temperature. Six novel heat resistance poly(amide‐imide)s (PAIs) with good inherent viscosities were synthesized, from the direct polycondensation reaction of N,N′‐[2,5‐bis(4‐aminobenzylidene)cyclopentanone]bistrimellitimide acid with several aromatic diamines, by two different methods such as direct polycondensation in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP)/triphenyl phosphite (TPP)/calcium chloride (CaCl₂)/pyridine (Py) and direct polycondensation in a p‐toluene sulfonyl chloride (tosyl chloride, TsCl)/pyridine (Py)/N,N‐dimethylformamide (DMF) system. All of the above polymers were fully characterized by ¹H NMR, FTIR, elemental analysis, inherent viscosity, solubility tests, UV‐vis spectroscopy, differential scanning calorimeter (DSC), thermogravimetric analysis (TGA), and derivative of thermaogravimetric (DTG). The resulted poly(amide‐imide)s (PAIs) have showed admirable good inherent viscosities, thermal stability, and solubility. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effective biosynthesis of poly(3‐hydoxy‐ butyrate‐co‐4‐hydroxybutyrate) with high 4‐hydroxybutyrate fractions by Wautersia eutropha in the presence of α‐amino acids

BACKGROUND: Biopolymers produced by microbes are in demand as their biodegradable and biocompatible properties make them suitable for disposable products and for potential use as biomaterials for medical applications. The effective microbial production of copolyesters of 3‐hydroxybutyrate (3HB) and 4‐hydroxybutyrate(4HB) with high molar fractions of 4HB unit by a wild‐type Wautersia eutropha H16 was investigated in culture media containing 4‐hydroxybutyric acid (4HBA) and different carbon substrates in the presence of various α‐amino acids. RESULTS: The addition of carbon sources such as glucose, fructose and acetic acid to the culture medium containing 4HBA in the presence of α‐amino acids resulted in the production of random poly(3HB‐co‐4HB) with compositions of up to 77 mol% 4HB unit, but the yields of copolyesters with 60–77 mol% 4HB units were less than 15 wt% of dried cell weights. In contrast, when carbon sources such as propionic acid and butyric acid were used as the co‐substrates of 4HBA in the presence of α‐amino acids, poly(3HB‐co‐4HB) copolyesters with compositions of 72–86 mol% 4HB were produced at maximally 47.2 wt% of dried cell weight (11.3 g L^?1) and the molar conversion yield of 4HBA to 4HB fraction in copolyesters was as high as 31.4 mol%. Further, poly(3HB‐co‐4HB) copolyesters with compositions of 93–96 mol% 4HB were isolated at up to 35.2 wt% of dried cell weights by fractionation of the above copolymers with chloroform/n‐hexane. CONCLUSION: The productivity of copolyesters with over 80 mol% 4HB fractions was as high as 0.146 g L^?1 h^?1 (3.51 g L^?1 for 24 h) by flask batch cultivation. Copyright © 2007 Society of Chemical Industry     

Fast crystallization of liquid crystalline copolyesters based on poly(ethylene terephthalate)

Crystallization of a series of liquid crystalline copolyesters prepared from p‐hydroxybenzoic acid (HBA), hydroquinone (HQ), terephthalic acid (TA), and poly(ethylene terephthalate) (PET) was investigated by using differential scanning calorimetry (DSC). It was found that these copolyesters are more crystalline than copolyesters prepared from PET and HBA. Insertion of HQ–TA disrupts longer rigid‐rod sequences formed by HBA and thus enhances molecular motion and increases the crystallization rate. The effects of additives on the crystallization of the copolyesters were also studied. Sodium benzoate (SB) and sodium acetate (SA) increase the crystallization rate of the copolyesters at low temperature, but not at high temperature. It is most likely that liquid crystalline copolyesters do not need nucleating agents, and small aggregates of local‐oriented rodlike segments in nematic phase could act as primary nuclei. Chain scission of the copolyesters caused by the reaction with the nucleating agents was proved by the determination of intrinsic viscosity and by the IR spectra. Diphenylketone (DPK) was shown to effectively promote molecular motion of chains, leading to an increase in the crystallization rate at low temperature, but it decreased the crystallization rate at high temperature. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 497–503, 2001     

Synthesis and characterization of poly(ethylene‐co‐trimethylene terephthalate)s

Taking advantage of a melt polycondensation process, a series of copolyesters composed of pure terephthalate acid (PTA), ethylene glycol (EG), and 1,3‐propanediol (1,3‐PDO) were synthesized. The component, molecular weight, molecular weight distribution, and thermal properties of the copolymers were characterized. The results show that the contents of trimethylene terephthalate (TT) units in the resulting copolyesters are higher than PDO compositions in original diol. Oligomer content in the copolyesters varies with the compositions and attains a minimum value when the TT ingredient is 49.52 mol %. The glass transition temperature (T_g) of the copolyesters varies from 78.5°C for PET (polyethylene terephthalate) to 43.5°C for PTT (polytrimethylene terephthalate) and decreases monotonically with the components. The copolyesters are amorphous copolymers when TT content is in the range of 32.4–40.8 mol %, as calculated from the melting enthalpy (ΔH_m) measured via differential scanning calorimetry. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1511–1521 2006     

Rheological and thermal properties of blends of modified poly(ethylene terephthalate) with p‐acetoxybenzoic acid and poly(butylene terephthalate)

Blending of thermotropic liquid crystalline polyesters (LCPs) with conventional polymers could result in materials that can be used as an alternative for short fiber‐reinforced thermoplastic composites, because of their low melt viscosity as well as their inherent high stiffness and strength, high use temperature, and excellent chemical resistance and low coefficient of expansion. In most of the blends was used LCP of 40 mol % of poly(ethylene terephthalate) (PET) and 60 mol % of p‐acetoxybenzoic acid (PABA). In this work, blends of several copolyesters having various PABA compositions from 10 to 70 mol % and poly(butylene terephthalate) (PBT) were prepared and their rheological and thermal properties were investigated. For convenience, the copolyesters were designated as PETA‐x, where x is the mol % of PABA. It was found that PET‐60 and PET‐70 copolyesters decreased the melt viscosity of PBT in the blends and those PBT/PETA‐60 and PBT/PETA‐70 blends showed different melt viscosity behaviors with the change in shear rate, while blends of PBT and PET‐x having less than 50 mol % of PABA exhibited totally different rheological behaviors. The blends of PBT with PETA‐50, PETA‐60, and PETA‐70 showed the morphology of multiple layers of fibers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1797–1806, 1999     

Thermal and morphological properties of thermotropic liquid‐crystalline copolyesters containing poly(ethylene terephthalate), 4‐hydroxyphenylacetic acid and main‐chain rigid aromatic units

Thermotropic liquid‐crystalline polymers (TLCPs) have aroused considerable interest due to their attractive properties as high‐performance materials. Significant research attention has been devoted to investigating the relationship among monomer structures, syntheses and end‐use properties of TLCPs. The study reported here concerns the preparation, characterization and melt spinning of novel copolyesters containing two different flexible units together with two different aromatic units in the polymer chains. A range of copolyesters based on p‐hydroxybenzoic acid (p‐HBA), m‐hydroxybenzoic acid, p‐hydroxyphenylacetic acid and poly(ethylene terephthalate) were synthesized. The liquid crystallinity, thermal properties and degrees of crystallinity of these copolyesters were investigated using hot‐stage polarized light microscopy, differential scanning calorimetry, thermogravimetry and wide‐angle X‐ray diffraction. Copolyester fibres were characterized using scanning electron microscopy. The copolyesters were melt‐processable, thermally stable and could be processed above their melting temperatures without degradation. The degree of crystal structure was found to depend upon the content of p‐HBA. The fibres prepared showed that polymer chains had a well‐developed fibrillar structure. Novel TLCPs containing flexible units in the main chain were synthesized and characterized. Copolyesters containing p‐HBA units ranging from 55 to 70 mol% exhibited phase‐separated liquid‐crystalline morphology, appropriate melting temperatures and high thermal stability for melt processing. Copyright © 2010 Society of Chemical Industry