Binding of metal cations to chemically modified wool and antimicrobial properties of the wool–metal complexes

Wool was modified by treatment with tannic acid (TA) or by acylation with ethylenediaminetetraacetic (EDTA) dianhydride. Kinetics of modification with TA and acylation with EDTA–dianhydride was investigated as a function of the reaction time. Wool displayed a higher breaking load and lower elongation at break as the degree of acylation increased. The absorption of metal cations (Ag⁺, Cu²⁺) by untreated and chemically modified wool was studied as a function of the kind of modifying agent, weight gain, and pH of the metal solution. Absorption of Ag⁺ and Cu²⁺ at alkaline pH increased with increasing weight gain of both TA and EDTA–dianhydride. The absorption of metal cations by untreated and TA‐treated wool below pH 7 was negligible. Acylation with EDTA–dianhydride enabled wool to absorb and bind significant amounts of metal cations at acidic and neutral pHs. The wool–Ag complexes exhibited low levels of metal desorption at acidic pH, irrespective of chemical modification. Higher levels of metal desorption were shown by wool–Cu and wool–EDTA–Cu complexes. Wool–Ag complexes exhibited prominent antimicrobial activity against Cornebacterium and E. coli. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3513–3519, 2001     

Preparation of metal‐containing protein fibers and their antimicrobial properties

Bombyx mori silk, Antheraea pernyi silk, and wool fibers were chemically modified by treatment with tannic acid (TA) or by acylation with ethylenediaminetetraacetic (EDTA) dianhydride. Kinetics of TA loading or acylation with EDTA‐dianhydride varied from fiber to fiber. B. mori silk and wool displayed the highest weight gains with TA and EDTA‐dianhydride, respectively. The uptake of different metal ions (Ag⁺, Cu²⁺, Co²⁺) by protein fibers, either untreated or chemically modified, was studied as a function of weight gain and pH of the aqueous metal solution. Below pH 7, absorption of metal ions by untreated and TA‐treated fibers was negligible. Acylation with EDTA‐dianhydride enabled protein fibers to absorb and bind significant amounts of metal ions in the acidic and neutral pH range. The levels of metal desorption at acidic pH depended on the fiber‐metal combination. Untreated protein fibers usually displayed the lowest stability of the metal complex. Metal complexes with protein fibers exhibited prominent antimicrobial activity against the plant pathogen Cornebacterium. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 638–644, 2003     

Degree of crosslinking and physical properties of dimethyloldihydroxyethyleneurea/acrylic acid crosslinked cotton fabrics after treatment with various metallic salts

Three metallic salts were used to posttreat dimethyloldihydroxyethyleneurea (DMDHEU)/acrylic acid (AA) crosslinked cotton fabrics, and the results showed that at a given value of the tensile strength retention (TSR), the dry crease recovery angle (DCRA) and wet crease recovery angle (WCRA) of the crosslinked and posttreated fabrics were higher than those of the DMDHEU–AA‐treated fabrics, and those of the crosslinked and posttreated fabrics were in the order of Ag⁺ > Cu⁺² > Al⁺³. The DCRA and TSR values for the crosslinked and posttreated fabrics were higher than those for the DMDHEU–AA‐crosslinked fabrics, and those for the crosslinked and posttreated fabrics were in the order of Ag⁺ > Cu⁺² > Al⁺³; however, WCRA values for the crosslinked and posttreated fabrics were lower than those for the DMDHEU–AA‐crosslinked fabrics, and those for the crosslinked and posttreated fabrics were ranked as Ag⁺ > Cu⁺² > Al⁺³ at a given number of crosslinks per anhydroglucose unit. IR spectra clearly revealed the different interactions and bonding states between the hydroxyl group of the cellulose and the various metallic ions and the strength of the interaction. All crosslinked and posttreated fabric samples showed good odor absorption and antibacterial and washing‐fastness properties. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 584–594, 2005     

Chemical modification of tussah silk with acid anhydrides

Tussah silk fibroin was chemically modified by acylation with aliphatic, aromatic, and hydrophobic acid anhydrides. The tussah silk fibers were pretreated by immersing them in a lithium thiocyanate (LiSCN) solution and then acylated in dimethylformamide (DMF) at elevated temperatures. Using this method, acylated tussah silk fibers with weight gains of 8–22% could be obtained. The pretreatment with LiSCN was necessary to promote the acylation. Without it, the reaction did not proceed. The optimum temperature and reaction time of the pretreatment was 55°C and 60 min, respectively. When examining the physical properties and the thermal behavior of both pretreated and acylated tussah silk, it was found that the mechanical properties and the position of the major DSC endothermic peak remained unchanged, regardless of pretreatment and acylation. The moisture regain of the pretreated tussah silk increased slightly while the moisture regain of the acylated silk decreased linearly with increasing weight gain. The chemical modification allows for a wide control of the tussah silk fiber's properties, making it possible to use tussah silk for the development and production of novel textile and biomaterials. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 382–391, 2000     

Synthesis and characterization of new optically active polymers carrying calix[4]arene and amino acid units in the main chain and their binding properties towards toxic heavy metals

BACKGROUND: A series of novel optically active polymers containing upper rim calix[4]arene was prepared from the polycondensation reaction of calix diamine derivative 2 with two optically active diacid chlorides. RESULTS: The optically active compounds were prepared from the reaction of a pyromellitic dianhydride with two chiral amino acids. The optically active polymers were obtained in a yield of 80–86% and had an inherent viscosity of 0.20–0.26 dL g^?1. The polymers were characterized using Fourier transform infrared and ¹H NMR spectroscopy and elemental analysis. Studies of the complexation of the polymers towards some alkali metal and toxic transition metal cations were performed using solid–liquid sorption procedures and comparisons made with the starting monomer. CONCLUSION: It is evident from the complexation studies that the polymers investigated are good polymeric ionophores for alkali metal cations like Na⁺ and K⁺, for Ag⁺ and for toxic heavy metal cations such as Cu²⁺, Co²⁺, Cd²⁺ and Hg²⁺. These polymers are good candidates for use in chiral stationary phases for separation of enantiomers in ionic media, as well for removing metal ions. Copyright © 2009 Society of Chemical Industry     

Physicochemical investigation of radiation‐grafted poly(acrylic acid)‐graft‐poly(tetrafluoroethylene–ethylene) copolymer membranes and their use in metal recovery from aqueous solution

ET‐g‐PAAc membranes were obtained by radiation grafting of acrylic acid onto poly(tetrafluoroethylene–ethylene) copolymer films using a mutual technique. The ion selectivity of the grafted membranes was determined toward K⁺, Ag⁺, Hg²⁺, Co²⁺, and Cu²⁺ in a mixed aqueous solution. The ion‐exchange capacity of the grafted membranes was measured by back titration and atomic absorption spectroscopy. The Hg²⁺ ion content of the membrane was more than that of either the K⁺ or Ag⁺ ions. The presence of metal ions in the membranes was studied by infrared and energy‐dispersive spectroscopy measurements. Scanning electron microscopy of the grafted and metal‐treated grafted membranes showed modification of the morphology of the surface due to the adsorption of K⁺ and Ag⁺ ions. No change was observed for the surface of the membrane that was treated with Hg²⁺ ions. The thermal stability of different membranes was improved more with Ag⁺ and Hg²⁺ ions than with K⁺ ions. It was found that the modified grafted membranes possessed good hydrophilicity, which may make them promising candidates for practical applications, such as for cation‐exchange membranes in the recovery of metals from an aqueous solution. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2692–2698, 2002     

Chemical modification of silk with itaconic anhydride

Bombyx mori silk fibers were chemically modified by acylation with itaconic anhydride. The reactivity of the modifying agent toward silk fibroin was investigated on the basis of the amino acid analysis. We examined the physical properties, the structural characteristics, and the thermal behavior of modified silk fibers as a function of the weight gain. Silk fibers with a weight gain of 9%, corresponding to an acyl content of 68.9 mol/10⁵g, were obtained at the optimum reaction conditions for silk acylation (75°C for 3 h). The amount of basic amino acid residues (Lys, His, and Arg) decreased linearly as the weight gain increased. The alkali solubility increased proportionally with the weight gain, probably due to the dissolution of the modifying agent reacted with silk fibroin, and not to the degradation of the fibers induced by the chemical modification. The birefringence value, related to the molecular orientation, slightly decreased when the weight gain increased. The isotropic refractive index, associated with the crystallinity, increased when the weight gain ranged from about 5 to 7% and then remained unchanged. The moisture regain did not change regardless of the chemical modification, and the crease recovery behavior of modified silk fabrics did not show significant improvement. The thermal behavior of silk fibers was affected by the modification with itaconic anhydride. The decomposition temperature shifted up to 322°C, 10°C higher than the control silk fibers, suggesting a higher thermal stability induced by chemical modification.     

Isomerization-induced introduction of metal cations into polyoxomolybdate-surfactant hybrid crystals

Monovalent metal cations (Ag⁺, K⁺, and Cs⁺) were successfully introduced into inorganic-organic hybrid crystals composed from β-type octamolybdate (β-Mo₈) and hexadecylpyridinium (C₁₆py). The introduction of metal cations was induced by the molecular isomerization from α-Mo₈ to β-Mo₈ anion. All hybrid crystals consisted of alternate stacking of β-Mo₈ inorganic and C₁₆py organic layers. In the inorganic layers, the metal cations and β-Mo₈ anions were connected to form one- or two-dimensional arrangement, which depended on the ionic radius of metal cations.     

Modification of poly acrylic acid using calix[4]arene derivative for the adsorption of toxic heavy metals

Poly acrylic acid (PAA) was grafted with p‐t‐butyl calix[4]arene diamine (distal cone) (2) to adsorb toxic heavy metal and alkali metal cations. The grafting method includes the amidation reaction of PAA with calixarene diamine derivative 2 which was carried out in N,N‐dimethylformamide (DMF) and N–methyl‐2‐pyrrolidone (NMP) as solvents. The modified PAAs (PAA‐C1 and PAA‐C2) were characterized by FTIR, ¹H‐NMR, thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC). PAA‐C1 and PAA‐C2 were used to evaluate the sorption properties of some toxic heavy metal cations (Co²⁺, Cu²⁺, Cd²⁺, Hg²⁺), alkali metal cations (Na⁺, K⁺, Cs⁺), and Ag⁺. Results showed that the modified PAAs were good sorbents for heavy metal and alkali metal cations. The main goal of this project is to design hydrophobically modified PAA that is suitable for ion selective membranes and chemical sensor devices for adsorption of toxic heavy metals. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Removal of Cs1+, Sr2+ and Co2+ from aqueous solutions by adsorption on natural clinoptilolite

The adsorption properties of local clinoptilolite (Serbia) towards Cs⁺, Co²⁺, and Sr²⁺ were investigated by batch equilibration technique. The influence of equilibration time, initial metal cation concentration, solution pH and presence of EDTA on these properties was studied and discussed. Kinetic data were found to be well fitted with pseudo-second order kinetic model. Cs⁺ is preferably adsorbed by the natural clinoptilolite, followed by Sr²⁺ and Co²⁺. The Langmuir adsorption isotherm was used to determine the adsorption capacities from both single and mixed metal solutions. At pH range of 3–12 the adsorption of Cs⁺ remains almost constant, while at low pH (2–3) the adsorption is lesser. At initial pH range of 2–10 adsorption of Sr²⁺ remains approximately stable, whereas at initial pH > 10 adsorption increases significantly. The adsorption of Co²⁺ is low at low pH but increased remarkably with increasing pH and precipitated at pH > 8. Cs⁺ adsorption on the clinoptilolite was not affected by the presence of EDTA, while the presence of EDTA hinders the adsorption of Co²⁺ and Sr²⁺ on clinoptilolite.     

Synthesis of ion‐imprinting chitosan/PVA crosslinked membrane for selective removal of Ag(I)

A novel ion‐imprinted membranes were synthesized for selective removal and preconentration for Ag(I) ions from aqueous solutions. The membranes were obtained via crosslinking of chitosan (CS), PVA, and blend chitosan/PVA using glutaraldehyde (GA) as crosslinker. The FTIR spectra were used to confirm the membrane formation. Comparing with the nonimprinted membranes, Ag(I)‐imprinted CS and CS/PVA has higher removal capacity and selectivity for Ag⁺ ions. An enhancement in the Ag⁺ removal capacity by ～ 20% (from 77.8 to 94.4 mg g^–1) and ～ 50% (from 83.9 to 125 mg g^–1) was found in the Ag(I)‐imprinted CS and Ag(I)‐imprinted CS/PVA membranes, respectively, when compared with the nonimprinted membranes. Removal equilibra was achieved in about 40 min for the non‐ and ion‐imprinted CS/PVA. The pH and temperature significantly affected the removal capacity of ion‐imprinted membrane. The relative selectivity coefficient values of Ag⁺/Cu²⁺ and Ag⁺/Ni²⁺ are 9 and 10.7 for ion‐imprinted CS membrane and 11.1 and 15 for ion‐imprinted CS/PVA membrane when compared with nonimprinted membranes. The imprinted membranes can be easily regenerated by 0.01M EDTA and therefore can be reused at least five times with only 15% loss of removal capacity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of Receiving Phase Anion on Macrocycle-Mediated Cation Transport Rates and Selectivities in Water—Toluene—Water Emulsion Membranes

Abstract

Relative transport rates of metal nitrates (Na⁺, K⁺, Rb⁺, Cs⁺, Ag⁺, T1⁺, Mg²⁺, Ca²⁺, Sr²⁺, Ba²⁺, Zn²⁺, and Pb²⁺) were measured alone and in combination with either Pb²⁺, Ag⁺, or T1⁺ in a water-toluene-water emulsion membrane system. The toluene phase contained the surfactant Span 80 and the crown ether dicyclohexano-18-crown-6 (DC18C6). The aqueous receiving phase contained the lithium salt of one of the following anions: pyrophosphate, thiosulfate, hydroxide, chloride, formate, nitrate. In the case of the metal combinations, chloride and formate ions were not studied. Unless significant complexation occurred both between the transported cation and the anion in the receiving phase and between the cation and DC18C6 in the membrane phase, there was little or no transport of the cation from the source phase to the receiving phase. Selective removal of Pb²⁺ and of Ag⁺ from binary mixtures of these cations with each of the cations listed was demonstrated using the emulsion membrane.     

An investigation into transition metal ion binding properties of silk fibers and particles using radioisotopes

Silk is a structural protein fiber that is stable over a wide pH range making it attractive for use in medical and environmental applications. Variation in amino acid composition has the potential for selective binding for ions under varying conditions. Here we report on the metal ion separation potential of Mulberry and Eri silk fibers and powders over a range of pH. Highly sensitive radiotracer probes, ⁶⁴Cu²⁺, ¹⁰⁹Cd²⁺, and ⁵⁷Co²⁺ were used to study the absorption of their respective stable metal ions Cu²⁺, Cd²⁺, and Co²⁺ into and from the silk sorbents. The total amount of each metal ion absorbed and time taken to reach equilibrium occurred in the following order: Cu²⁺ > Cd²⁺ > Co²⁺. In all cases the silk powders absorbed metal ions faster than their respective silk fibers. Intensive degumming of the fibers and powders significantly reduced the time to absorb respective metal ions and the time to reach equilibrium was reduced from hours to 5–15 min at pH 8. Once bound, 45–100% of the metal ions were released from the sorbents after exposure to pH 3 buffer for 30 min. The transition metal ion loading capacity for the silk sorbents was considerably higher than that found for commercial ion exchange resins (AG MP‐50 and AG 50W‐X2) under similar conditions. Interestingly, total Cu²⁺ bound was found to be higher than theoretically predicted values based on known specific Cu²⁺ binding sites (AHGGYSGY), suggesting that additional (new) sites for transition metal ion binding sites are present in silk fibers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Silver deposition from its nitrate solutions by hydrogenated palladium

The currentless deposition of Ag⁺ cations from silver nitrate solutions has been found on the surface of hydrogenated Pd (Pd?H). This process has been shown to proceed via a chemico-catalytic mechanism. It has been demonstrated that the major fraction of silver deposited onto the Pd-H system from the nitrate solutions in the first 0.5–1 h of holding in the solution. A minimal size of silver crystallites (26–40 nm) was found when deposited from the diluted nitrate solutions that contain 0.32–2.5 g/L of Ag. The study has revealed that the currentless Ag deposition on the Pd–H surface is accompanied by the formation of the colloid phase of Ag crystallites. It has been established that the Pd–H system could purify solutions of Ag⁺ when the amount of hydrogen in Pd exceeded the amount of Ag⁺ in the solution.     

Acylated Anthocyanins from Red Cabbage and Purple Sweet Potato Can Bind Metal Ions and Produce Stable Blue Colors

Red cabbage (RC) and purple sweet potato (PSP) are naturally rich in acylated cyanidin glycosides that can bind metal ions and develop intramolecular π-stacking interactions between the cyanidin chromophore and the phenolic acyl residues. In this work, a large set of RC and PSP anthocyanins was investigated for its coloring properties in the presence of iron and aluminum ions. Although relatively modest, the structural differences between RC and PSP anthocyanins, i.e., the acylation site at the external glucose of the sophorosyl moiety (C2-OH for RC vs. C6-OH for PSP) and the presence of coordinating acyl groups (caffeoyl) in PSP anthocyanins only, made a large difference in the color expressed by their metal complexes. For instance, the Al³⁺-induced bathochromic shifts for RC anthocyanins reached ca. 50 nm at pH 6 and pH 7, vs. at best ca. 20 nm for PSP anthocyanins. With Fe²⁺ (quickly oxidized to Fe³⁺ in the complexes), the bathochromic shifts for RC anthocyanins were higher, i.e., up to ca. 90 nm at pH 7 and 110 nm at pH 5.7. A kinetic analysis at different metal/ligand molar ratios combined with an investigation by high-resolution mass spectrometry suggested the formation of metal–anthocyanin complexes of 1:1, 1:2, and 1:3 stoichiometries. Contrary to predictions based on steric hindrance, acylation by noncoordinating acyl residues favored metal binding and resulted in complexes having much higher molar absorption coefficients. Moreover, the competition between metal binding and water addition to the free ligands (leading to colorless forms) was less severe, although very dependent on the acylation site(s). Overall, anthocyanins from purple sweet potato, and even more from red cabbage, have a strong potential for development as food colorants expressing red to blue hues depending on pH and metal ion.     

Preparation of water‐repellent silks by a reaction with octadecenylsuccinic anhydride

Silk fibers and membranes were acylated with octadecenylsuccinic anhydride (ODSA) at 75°C for different times. Swelling [N,N‐dimethylformamide (DMF) and dimethyl sulfoxide (DMSO)] and nonswelling (xylene) solvent media were used for the reaction. Silk membranes that reacted in DMF or DMSO displayed faster reaction kinetics and attained higher weight‐gain values than fibers. The effect of the solvent on the reaction yield was in the following order: DMSO > DMF ? xylene. The Fourier transform infrared spectra of acylated silk samples showed the characteristic absorption bands of the anhydride at 2990, 2852, 1780–1700, and 1170 cm^?1. The intensity of the latter band, which increased linearly with the weight gain, was used as a marker for evaluating the reaction kinetics of the samples acylated in the nonswelling medium. The moisture regain and water retention of silk fibers acylated with ODSA decreased significantly, regardless of the solvent system used. Accordingly, the water repellency increased. Acylation induced an increase in the thermal stability of the silk fibers and membranes. Fine particles adhering to the surfaces of the silk fibers acylated in xylene were detected by scanning electron microscopy. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 324–332, 2003     

Poly(2‐acrylamido glycolic acid‐co‐2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid): Synthesis,characterization, and retention properties for environmentally impacting metal ions

Poly(2‐acrylamido glycolic acid‐co‐2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid) [P(AGA‐co‐APSA)] was synthesized by radical polymerization in an aqueous solution. The water‐soluble polymer, containing secondary amide, hydroxyl, carboxylic, and sulfonic acid groups, was investigated, in view of their metal‐ion‐binding properties, as a polychelatogen with the liquid‐phase polymer‐based retention technique under different experimental conditions. The investigated metal ions were Ag⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Pb²⁺, and Cr³⁺, and these were studied at pHs 3, 5, and 7. P(AGA‐co‐APSA) showed efficient retention of all metal ions at the pHs studied, with a minimum of 60% for Co(II) at pH 3 and a maximum close to 100% at pH 7 for all metal ions. The maximum retention capacity (n metal ion/n polymer) ranged from 0.22 for Cd²⁺ to 0.34 for Ag⁺. The antibacterial activity of Ag⁺, Cu²⁺, Zn²⁺, and Cd²⁺ polymer–metal complexes was studied, and P(AGA‐co‐APSA)–Cd²⁺ presented selective antibacterial activity for Staphylococcus aureus with a minimum inhibitory concentration of 2 μg/mL. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Chromatographic Separations of Metal Ions on Zirconium Tungstoarsenate Impregnated Ion-Exchange Papers

Abstract

A new heteropolyacid salt ion-exchanger, zirconium tungstoarsenate, has been used for preparing impregnated ion-exchange papers. Twenty-nine metal ions have been chromatographed and R_F values determined in seven different mixed solvent systems containing 1-propanol and HNO³ or HCl. On the basis of the difference in selectivities for different metal ions on impregnated papers, a large number of binary and ternary separations has been obtained. Some of the important separations achieved are Ag⁺–Tl⁺, Ag⁺–Pt(IV), Zn²⁺–Hg²⁺, Sb³⁺–Bi³⁺, Zn²⁺–UO₂ ²⁺, Fe²⁺–Fe³⁺, Sb³⁺–Bi³⁺–Hg²⁺, Ag⁺–Ba²⁺–UO₂ ²⁺, and Ag⁺–Zn²⁺–Cu²⁺–Sn²⁺. The results are compared with those obtained on plain papers.     

Electrocatalytic activities of gold-5-amino-2-mercaptobenzimidazole-M self-assembled monolayer complexes (M: Ag, Cu) for hydroquinone oxidation investigated by CV and EIS

Electrocatalytic activity of a new catalyst toward the oxidation reaction of hydroquinone as a model compound is described. The catalyst was formed by immobilizing metal cations on the topside of a gold-5-amino-2-mercaptobenzimidazole, self-assembled monolayer (Au-5A2MBI-Mⁿ⁺ SAM, Mⁿ⁺: Cu²⁺, Ag⁺) electrode. Preparation steps and the electrocatalytic activity of the catalyst were studied by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The EIS data were approximated by appropriate electronic equivalent circuit models from which kinetic parameters, such as charge transfer resistance, double layer capacitance, and apparent rate constant (k_app), were estimated. Excellent activity was observed for Au-5A2MBI-Ag⁺ SAM with the following order: Au-5A2MBI-Ag⁺ > Au-5A2MBI-Cu²⁺ > Au-5A2MBI, after testing many modified electrodes. The increased activity originates from a modification of the Au-5A2MBI structure by mediating the effect of Ag⁺. This behavior was understood from significant increases in the k_app without significant changes in the double layer capacitance.     

Removal of Ni(II) and Zn(II) from an aqueous solutionby reverse osmosis

The removal of Ni⁺² and Zn⁺² from an aqueous solution by reverse osmosis (RO) at different pH, conductivity and EDTA concentrations was investigated. In addition, the removal in the pretreatment units (PU) with filtration (F) and granular activated carbon (GAC) at the same conditions was also determined. It was observed that Zn⁺² rejections did not change much with pH, usually less than 0.88 mg/l, and Ni⁺² rejection was below the detection limits of AAS in the range of pH 4-8. While Ni⁺² and Zn⁺² were removed 23-25% and 25-45%, respectively, by PU, the rejection of Ni⁺² and Zn⁺² was, respectively, determined to be higher than 99.2% and 98.8% by PU+RO at experiments related to the determination of the effect of initial metal concentration on rejection. It was found that the influent conductivity affected metal rejection at an unimportant level, but the increase of conductivity affected the effluent conductivity. The addition of EDTA into the aqueous solution increased Ni⁺² and Zn⁺² rejection from 99.3% to 99.7% and from 98.9% to 99.6% at an EDTA concentration of 240 ppm, respectively.