The effects of acrylate monomers and polystyrene addition on the morphology of DOP‐plasticized styrene–acrylate polymer particles prepared by SPG emulsification and suspension polymerization

Fairly uniform copolymer particles of methyl acrylate (MA), butyl acrylate (BA), or butyl methacrylate (BMA) were synthesized via Shirasu porous glass (SPG) membrane and followed by suspension polymerization. After a single‐step SPG emulsification, the emulsion composed mainly of the monomers. Hydrophobic additives of dioctyl phthalate (DOP), polystyrene molecules, and an oil‐soluble initiator, suspended in an aqueous phase containing poly(vinyl alcohol) (PVA) stabilizer and sodium nitrite inhibitor (NaNO₂), were subsequently subjected to suspension polymerization. Two‐phase copolymers with a soft phase and a hard phase were obtained. The composite particles of poly(St‐co‐MA)/PSt were prepared by varying the St/PSt ratios or the DOP amount. The addition of PSt induced a high viscosity at the dispersion phase. The molecular weight slightly increased with increasing St/PSt concentration. The multiple‐phase separation of the St‐rich phase and PMA domains, observed by transmission electron microscopy, was caused by composition drift because the MA reactivity ratio is greater than that of St. The addition of DOP revealed the greater compatibility between the hard‐St and soft‐MA moieties than that without DOP. The phase morphologies of poly(St‐co‐MA), poly(St‐co‐BMA), and their composites with PSt were revealed under the influence of DOP. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1195–1206, 2006     

Synthesis of 100 μm uniform porous spheres by SPG emulsification with subsequent swelling of the droplets

100 μm porous p(styrene-co-divinylbenzene) (PS-DVB) microspheres were synthesized by employing a particular membrane emulsification technique, and subsequent swelling of the seed droplets. DVB dissolving a water-insoluble substance, hexadecane (HD), and an initiator was permeated through a SPG (Shirasu porous glass) membrane, and the uniform (seed) droplets were released to a stabilizer solution acting as the continuous phase. The average droplet size was around 30 μm, and this emulsion was mixed with a secondary emulsion of much smaller size consisting of more hydrophilic components, a mixture of styrene, middle chain alcohol (C6 to C8), dichlorobenzene, and isoamyl acetate, which promotes the degradative diffusion process of the components. After all the droplets in the secondary emulsion virtually disappeared, the seed droplets were swollen to a maximum 110 μm. Polymerization was carried out at 348 K under a nitrogen atmosphere. Uniform porous spheres of 100 μm with the coefficient of variation less than 10% were obtained. Specific surface area was 350 m²/g. Careful controlling of the specific gravity of swollen droplets and the choice of solvents balancing between the good solvency for the polymer and polarity (solubility in water) proved vital in order that the polymerization may proceed without an extensive phase separation in the early stage, which eventually induces breakup of the droplets. The three component system, isoamyl acetate-hexanol-o-dichlorobenzene, provided an adequate cosolvent for these purposes. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 931–942, 1997     

Study of the preparation and mechanism of formation of hollow monodisperse polystyrene microspheres by SPG (Shirasu Porous Glass) emulsification technique

In a previous study, it was found that monodisperse polystyrene (PSt) hollow particles can be prepared under special conditions by combining a Shirasu Porous Glass (SPG) emulsification technique and subsequent suspension polymerization process. That is, a mixture of styrene (St), N,N‐dimethylamino ethyl methacrylate (DMAEMA), hexadecane (HD), and initiator N, N′‐azobis(2,4‐dimethylvaleronitrile) (ADVN) was used as the dispersed phase in an aqueous phase containing poly(vinyl pyrrolidone) (PVP), sodium lauryl sulfate (SLS), and water‐soluble inhibitor. The dispersed phase was created by pushing the oil phase through the uniform pores of an SPG membrane into the continuous phase to form uniform droplets. Then, the droplets were polymerized at 70°C. It has been puzzling that hollow microspheres were obtained only when sodium nitrite (NaNO₂) was used as a water‐soluble inhibitor, while one‐hole particles were formed when hydroquinone (HQ) or diaminophenylene (DAP) was used. In this study, the mechanism of formation of the hollow microspheres was verified by measuring the variation of diameter, molecular weight distribution, and monomer conversion, and by observing morphological changes during the polymerization, as well as by changing the type and amount of hydrophilic monomer, and initiator. It was found that the diameter of the oil droplets decreased, and a large amount of secondary new particles formed immediately after polymerization started in the case of NaNO₂. However, there was no such apparent behavior to be observed when HQ or DAP was used. It was determined that the hollow particles formed due to the rapid phase separation between PSt and HD, and as a consequence, a large amount of monomer diffused into the aqueous phase to form the secondary particles. Rapid phase separation confined the HD inside the droplets, a nonequilibrium morphology. On the other hand, one‐hole particles, representing an equilibrium morphology, formed when the phase separation occurred slowly because a lot of monomer existed inside of the droplets to allow mobility of the PSt. The addition of DMAEMA allowed the hollow particles to be formed more easily by decreasing the interfacial tension between the copolymer and aqueous phase. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1530–1543, 2002     

Mechanism of suspension polymerization of uniform monomer droplets prepared by glass membrane (Shirasu Porous Glass) emulsification technique

The mechanism of the unique suspension polymerization of uniform monomer droplets, without coalescence and breakup during the polymerization, was investigated using styrene (S) as a monomer mixed with water‐insoluble hexadecane (HD). The glass membrane (Shirasu Porous Glass, SPG) emulsification technique was employed for the preparation of uniform droplets. Depending on the pore sizes of the SPG membranes (1.0, 1.4, and 2.9 μm), polymer particles of an average diameter ranging from 5.6 to 20.9 μm were obtained with the coefficient of variation (CV) being close to 10%. The role of HD was to prevent the degradation of the droplets by the molecular diffusion process. Sodium nitrite was added in the aqueous phase to kill the radicals desorbed from the droplets (polymer particles), thereby suppressing the secondary nucleation of smaller particles. Each droplet behaved as an isolated locus of polymerization. With the presence of HD, the initial polymerization rate was proportional to 0.24th power of the benzoil peroxide (BPO) concentration. This peculiar behavior as compared with the ordinary suspension polymerization was explained by introducing the assumption that each droplet was composed of isolated compartments (cells) in which active polymeric radicals were dissolved in an S‐rich phase and surrounded by a rather incompatible S/HD (continuous) phase. The average number of radicals in the droplet increased initially due to the separate existence of polymeric radicals in compartments. As the polymerization progressed, the HD‐rich phase gradually separated, eventually forming macrodomains, which were visible by an optical microscope. The phase separation allowed polystyrene chains to dissolve in a more favorable S phase, and the homogeneous bulk polymerization kinetics took over, resulting in a gradual decrease of the average number of radicals in the droplet until the increase of viscosity induced the gel effect. When no HD was present in the droplets, the polymerization proceeded in accordance with the bulk mechanism except for the initial retardation by the entry of inhibiting radicals generated from sodium nitrite in the aqueous phase. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1025–1043, 2000     

Synthesis and property behavior of dioctyl phthalate plasticized styrene–acrylate particles by Shirasu porous glass emulsification and subsequent suspension copolymerization

Two‐phase model styrene–acrylate copolymers were synthesized with a soft phase consisting of methyl acrylate, butyl acrylate, and butyl methacrylate. Besides the styrenic copolymers, copolymers containing a hard phase of methyl methacylate and methyl acrylate were also synthesized. Comonomer droplets with a narrow size distribution and fair uniformity were prepared using an SPG (Shirasu porous glass) membrane having pore size of 0.90 μm. After the single‐step SPG emulsion, the emulsion droplets were composed mainly of monomers, hydrophobic additives, and an oil‐soluble initiator, suspended in the aqueous phase containing a stabilizer and inhibitor. These were then transferred to a reactor, and subsequent suspension polymerization was carried out. Uniform copolymer particles with a mean diameter ranging from 3 to 7 μm, depending on the recipe, with a narrow particle size distribution and a coefficient of variation of about 10% were achieved. Based on the glass‐transition temperatures, as measured by differential scanning calorimetry, the resulting copolymer particles containing a soft phase of acrylate were better compatibilized with a hard phase of methyl methacrylate than with styrene with dioctyl phthalate (DOP) addition. Glass‐transition temperatures of poly(MMA‐co‐MA) particles were strongly affected by the composition drift in the copolymer caused by their substantial difference in reactivity ratios. Incorporation of DOP in the copolymer particles does not significantly affect the glass‐transition temperature of MMA‐ or MA‐containing copolymer particles, but it does affect the St‐containing copolymer and particle morphology of the copolymers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3037–3050, 2003     

Preparation of polyurethaneurea (PUU) uniform spheres by SPG membrane emulsification technique

Uniform polyurethaneurea (PUU) spheres were prepared from 20–40 wt % urethane prepolymer (UP) solution of xylene. Uniform droplets were formed with the Shirasu porous glass (SPG) membranes of 1.42, 5.25, and 9.5 μm pore size, dispersed in an aqueous phase with dissolved stabilizers, and allowed to stand for the chain extension at the room temperature with diamines that were added after the emulsification. The reaction progressed rapidly by an addition of ethyl acetate to the aqueous phase, promoting the diffusion of diamines into the droplets. The reaction of —NCO groups with water did not hamper the emulsification process, which normally occurred in 1 to 2 h, yielding stable droplets with the coefficient of variation around 10%. No instability or coagulation occurred, while standing for the chain extension, and solid, spherical PUU particles of 5–20 μm were obtained after removal of the solvent. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2237–2245, 2000     

Application of porous microspheres prepared by SPG (Shirasu porous glass) emulsification as immobilizing carriers of glucoamylase (GluA)

Fairly uniform spheres of crosslinked polystyrene (PS) and polymethyl methacrylate (PMMA), prepared by a particular emulsification process using SPG (Shirasu Porous Glass) membranes and subsequent suspension polymerization, were applied for immobilizing carriers of Glucoamylase (GluA). A mixture of monomers, solvents, and oil-soluble initiator was allowed to permeate through the micropores of SPG, suspended in an aqueous solution of poly(vinyl alcohol), and polymerized while retaining the narrow size distribution during polymerization. A small amount of acrylic acid or glycidyl methacrylate (GMA) was incorporated for the immobilization of GluA via covalent bonding. Although GluA has been regarded as being difficult to retain its activity after the immobilization process, a porous structure of the carriers definitely favored the immobilization, and a maximum 55% relative activity (RA) was obtained by the physical adsorption to PMMA spheres. The reaction of epoxide in GMA with 6-aminocaproic acid provided a spacer arm for the carboxyl group. An improvement of activity was expected by the incorporation of the spacer arms; however, barely noticeable activity was observed for PMMA carriers either by the physical adsorption or by the covalent bonding. A slight improvement was observed for PS carriers with spacers compared to the carriers without them. The diffusion process of oligosaccharides in the porous carriers seemed to retard the rate of hydrolysis in the case of largest carriers, 60 μm PS-DVB-AA spheres. The activity of immobilized GluA was retained during a long storage period of more than 150 days, some of them even increasing gradually, while the activity of native GluA dropped to zero after 100 days. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 2655–2664, 1997     

Synthesis of greater than 10‐μm‐sized,monodispersed polymer particles by one‐step seeded polymerization for highly monomer‐swollen polymer particles prepared utilizing the dynamic swelling method

The thermodynamic simulation under the kinetic control state indicates that 1.77‐µm‐sized monodispersed polystyrene (PS) particles can absorb 500 times the amount of the styrene monomer with keeping the monodispersity by the “dynamic swelling method” (DSM) which the authors proposed in 1991. Actually, about 14.1‐µm‐sized monodispersed styrene‐swollen PS particles in which PS seed particles absorbed 500 times the amount of styrene monomer were successfully prepared utilizing DSM. By one‐step seeded polymerization for the dispersion of the swollen particles at 30°C for 48 h with the 2,2′‐azobis(4‐methoxy‐2,4‐dimethyl valeronitrile) initiator, 13.1‐µm‐sized monodispersed PS particles were produced. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 278–285, 1999     

Adsorption of bovine serum albumin to a polymer brush prepared by atom-transfer radical polymerization in a porous inorganic membrane

Protein adsorption was performed by a polymer brush prepared by atom-transfer radical polymerization (ATRP) to a porous inorganic membrane. The porous inorganic membrane, Shirasu Porous Glass made from silica, was modified with a halogen-containing compound to bind the active species for the polymerization. Glycidyl methacrylate was polymerized from the halogen compound by ATRP for a prescribed time, and subsequently chemically modified. The progression of the chemical modification allowed the membrane to lower the phosphate-buffer flux of the porous membrane due to the attachment of the polymer brush. Bovine serum albumin (BSA), as a model protein, was adsorbed at 12 mg per gram of the membrane in permeating BSA solution through the polymer-brush-attached porous membrane.     

Study on preparation of monodispersed poly(styrene‐co‐N‐dimethylaminoethyl methacrylate) composite microspheres by SPG (Shirasu Porous Glass) emulsification technique

Monodispersed poly(styrene‐co‐N‐dimethylaminoethyl methacrylate) [P(St‐DMAEMA)] composite microspheres were prepared by employing a Shirasu Porous Glass (SPG) emulsification technique. A mixture of monomer, hexadecane (HD), and initiator N,N′‐azobis(2,4‐dimethylvaleronitrile) (ADVN) was used as a dispersed phase and an aqueous phase containing stabilizer [poly(vinyl pyrrolidone) (PVP) or poly(vinyl alcohol) (PVA)], sodium lauryl sulfate (SLS), and water‐soluble inhibitor [hydroquinone (HQ), diaminophenylene (DAP), or sodium nitrite (NaNO₂)], was used as a continuous phase. The dispersed phase was permeated through the uniform pores of SPG membrane into the continuous phase by a gas pressure to form the uniform droplets. Then, the droplets were polymerized at 70°C. The effects of inhibitor, stabilizer, ADVN, and DMAEMA on the secondary nucleation, DMAEMA fraction in the polymer, conversion, and morphologies of the particles were investigated. It was found that the secondary nucleation was prevented effectively in the presence of HQ or DAP when PVP was used as the stabilizer. The secondary particle was observed when ADVN amount was raised to 0.3 g (/18 g monomer); however, no secondary nucleation occurred even by increasing DMAEMA fraction to 10 wt %. This result implied that the diffusion of ADVN into the aqueous phase was a main factor responsible to the secondary nucleation more than that of DMAEMA. The hollow particles were obtained when NaNO₂ was used, while one‐hole particles formed in the other cases. By adding crosslinking agent, the hole disappeared and the monomer conversion was improved. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2408–2424, 2001     

Preparation of polystyrene/poly(methyl methacrylate) core‐shell composite particles by suspension‐emulsion combined polymerization

Suspension‐emulsion combined polymerization process, in which methyl methacrylate (MMA) emulsion polymerization constituents (EPC) were drop wise added to styrene (St) suspension polymerization system, was applied to prepare polystyrene/poly(methyl methacrylate) (PS/PMMA) composite particles. The influences of the feeding condition and the composition of EPC on the particle feature of the resulting composite polymer particles were investigated. It was found that PS/PMMA core‐shell composite particles with a narrow particle size distribution and a great size would be formed when the EPC was added at the viscous energy dominated particle formation stage of St suspension polymerization with a suitable feeding rate, whereas St‐MMA copolymer particles or PS/PMMA composite particles with imperfect core‐shell structure would be formed when the EPC was added at the earlier or later stage of St suspension polymerization, respectively. It was also showed that the EPC composition affected the composite particles formation process. The individual latex particles would exist in the final product when the concentrations of MMA monomer, sodium dodecyl sulfate emulsifier, and potassium persulfate initiator were great in the EPC. Considering the feature of St suspension polymerization and the morphology of PS/PMMA composite particles, the formation mechanism of PS/PMMA particles with core‐shell structure was proposed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

2‐Hydroxypropylmethacrylate based mono‐ and bifunctional gel beads prepared by suspension polymerization

Spherical and swellable gel beads in the size range 35–200 µm were prepared by suspension polymerization of 2‐hydroxypropylmethacrylate (HPMA). In the proposed method, a mixture of cyclohexanol and octanol was used as a diluent phase dispersed in an aqueous medium including poly(vinyl pyrrolidone) (PVP) as the stabilizer. The polymerization was initiated within the organic phase including the monomer and the crosslinker (ethylene glycol dimethacrylate) by an oil soluble initiator benzoyl peroxide. Spherical and swellable gel beads carrying both hydroxyl and carboxyl functional groups were also prepared by suspension copolymerization of HPMA and a water soluble comonomer (methacrylic acid). For this purpose, the suspension polymerization method proposed for HPMA was modified by using poly(vinyl alcohol) as a stabilizer instead of PVP. The effect of initiator concentration, polymerization temperature, monomer/diluent ratio, crosslinker concentration, stirring rate on yield, average size, size distribution, and carboxyl content of the HPMA based gel beads, were investigated. The swelling characteristics of the gel beads were defined. © 2000 Society of Chemical Industry     

Synthesis and characterization of polyurethaneurea–vinyl polymer (PUU–VP) uniform hybrid microspheres by SPG emulsification technique and subsequent suspension polymerization

Uniform polyurethaneurea–vinyl polymer (PUU–VP) hybrid microspheres of about 20 μm were prepared by a Shirasu porous glass (SPG) membrane emulsification technique and a subsequent radical suspension polymerization process, that is, a mixture of a 40 wt % urethane prepolymer (UP) solution of xylene and a vinyl monomer (VP) containing an initiator was permeated through the uniform pores of the SPG membrane into a continuous phase containing a stabilizer to form uniform droplets. Then, the droplets were allowed to stand for chain extension at room temperature with di‐ or triamines for 2 h in the absence or presence of ethyl acetate (EA), followed by suspension polymerization at 70°C for 24 h. The effect of the type and the amount of the monomer composition, crosslinker, and chain extender on the monomer conversion, particle morphology, and stability of the dispersion was investigated. A strong relationship was found between the compatibility of PUU with VP and the stability of the dispersion. The monomer conversion increased and the stability of the dispersion was improved as the amount of the crosslinker was increased. Solid and spherical PUU–VA hybrid particles with a smooth surface and a higher destructive strength were obtained when a trifunctional crosslinker and a chain extender were used together. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 163–178, 2003     

Morphology and thermodynamic analysis of composite polymer particles prepared by soap‐free emulsion polymerization in the presence of poly(methyl methacrylate) and polystyrene as biseeds

Biseeds emulsion polymerization was investigated with poly(methyl methacrylate) (PMMA) and polystyrene (PSt) as biseeds and styrene (St) as second‐stage monomer, as well as with thermodynamic analysis; namely, the principle of minimum interfacial free‐energy change was utilized to explain the competitiveness of different seeds for second‐stage monomer and the final equilibrium morphology of composite polymer particles. The experimental results indicated the polymeric particles prepared had bimodal size distribution and the PMMA seed particles showed a higher chance of obtaining St than that of the PSt seed particles, which was in agreement with the computational outcome by the principle of minimum interfacial free‐energy change. Owing to the kinetic factors, the equilibrium morphology could not be reached in the experiments. However, the results demonstrated that double or multiple seeds emulsion polymerization could be used as a model experiment to study the morphology of polymer particle and the morphological prediction. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2675–2680, 2004     

原位悬浮聚合PVC/纳米CaCO3的制备及其性能

利用原位悬浮聚合法制备了聚氯乙烯(PVC)／纳米CaCO3复合树脂,并对其性能进行了研究。结果表明。与PVC相比,PVC／纳米CaCO3复合树脂的热稳定性、增塑剂吸收量及表观密度等有所提高;冲击强度Eh4．9kJ／m^2增加到13．0kJ／m^2：拉伸强度由58．2MPa增加到59．5MPa;断裂伸长率由57．8％增加到75．6％,达到了增韧增强的效果。     

耐盐性高吸水树脂的反相悬浮制备过程及其结构表征

采用反相悬浮法合成耐盐性高吸水丙烯酸盐共聚物P(KAA-AM-NAM),研究了分散剂种类和用量、共聚单体配比等因素对聚合过程及产物吸水性的影响。利用电导、像衬光学显微镜对反相悬浮聚合反应过程进行了研究,用红外和热重分析对树脂的分子结构和热稳定性进行了表征。结果表明:以TX-10磷酸酯为分散剂,TX-10磷酸酯质量分数5.88%,N-羟甲基丙烯酰胺质量分数为3.6%时,反应过程稳定,树脂具有较大吸液率。反相悬浮聚合体系反应过程是由油包水到油水连续相互相贯穿,最后到水凝胶和油相共存的状态。红外光谱显示树脂中存在大量亲水基团,热分析知其热分解温度约420℃,热稳定性良好。     

Preparation and characterization of carbon black‐polystyrene composite particles by high‐speed homogenization assisted suspension polymerization

Composite particles of carbon black‐polystyrene with controllable size were successfully prepared using high‐speed homogenization‐assisted suspension polymerization. The carbon black particles were modified by oleic acid to make it more hydrophobic and more compatible with polymers before the encapsulation process. The effects of homogenization speed, homogenization time, agitation speed, pigment concentration, and stabilizer concentration on the properties of complex spheres were investigated in detail. The results of orthogonal experiments proved that the stabilizer concentration plays the most important role in controlling the size of complex particles. The particles were also characterized by FTIR and SEM. SEM photographs proved that the complex particles had good spherical forms with smooth surfaces. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Morphology and thermal behavior of MCPA6/SAN blends prepared by anionic ring‐opening polymerization of ϵ‐caprolactam

In this article, a series of blends of monomer casting polyamide 6 and styrene‐co‐acrylonitrile (MCPA6/SAN) were prepared by in situ anionic ring‐opening polymerization of ?‐caprolactam. Their morphology and thermal behaviors were investigated by means of scanning electron microscope, differential scanning calorimeter, and wide‐angle X‐ray diffraction (WAXD), respectively. The SAN phase had much finer domain in MCPA6/SAN than that in the PA6/SAN blends prepared by melt blending of PA6 and SAN. All the melting and crystallization parameters of MCPA6/SAN blends decreased gradually with the increase of SAN content, while the melting temperature was almost unchanged. These results were due to the hydrolysis reaction of SAN that occurred during the anionic polymerization of ?‐caprolactam. In addition, WAXD results showed that only α crystal forms existed in the MCPA6/SAN blends. In addition, the mechanical property of MCPA6 was improved obviously by incorporating a certain amount of SAN. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1357–1363, 2006     

Synthesis of 5‐vinyl‐m‐ phenylene‐m′‐phenylene‐32‐ crown‐10 and its radical polymerization behavior

Synthesis of a vinyl monomer, containing a 32‐membered crown ether unit (VCE) as a pendant group, was achieved by using tetra(ethylene glycol) dichloride, resorcinol, and 3,5‐dihydroxyacetophenone as starting materials. The product was identified by means of FTIR and ¹H‐NMR. It was found that this monomer readily polymerizes by the conventional radical initiator 2,2′‐ azobisisobutyronitrile (AIBN) to afford a polymer whose number‐average molecular weight is 36 kg/mol; however, the final conversion of the polymer was < 80%. The results of the copolymerization of VCE with styrene (ST) or acrylonitrile (AN) are also discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2372–2379, 2002     

Molecular selectivity of tyrosine-imprinted polymers prepared by seed swelling and suspension polymerization

Tyrosine-imprinted microspheres have been prepared in an aqueous system by seed swelling and suspension polymerization, using trimethylolpropane trimethacrylate (TRIM), acrylamide (AM) as well as methacrylic acid (MAA), linear polystyrene and toluene as crosslinker, functional monomers, seeds and porogens, respectively. The size distribution proved to be greatly influenced by the ratio of water:TRIM (W/T) and the concentration of dispersant. When W/T was 46:1 (v/v), 4.6% (by mass) of poly(vinyl alcohol) (PVA) was used as dispersant, the molar ratios of tyrosine, MAA, AM and TRIM were 1:8:8:17, the polymer beads had the better size monodispersity, and the average size was 135 µm, while the sizes of the pores on the beads surfaces ranged from 1.25 µm to 9.0 µm. The adsorption behaviour and molecular selectivity of the beads were analysed using liquid chromatography; the results showed that the adsorption behaviour of the beads followed the rule of Langmuir, and the value of saturated absorption was 0.197 mmol g⁻¹. The tyrosine-imprinted polymers exhibited an inherent selectivity for tyrosine; when phenylalanine was used as the competing molecule the separation factor α was up to 1.91. However, the control polymers did not have this special molecule-selection capability, and the relative separation factor β was about 1.82 compared with the imprinted polymers. © 2002 Society of Chemical Industry