Influence of process parameters on the structure formation of man‐made cellulosic fibers from ionic liquid solution

The influence of dry‐jet wet spinning parameters on the production of man‐made cellulosic fibers from 13 wt % cellulose/1,5‐diazabicyclo[4.3.0]non‐5‐ene acetate solutions was investigated. The spinneret nozzle diameter, extrusion velocity, draw ratio, and coagulation bath temperature were the studied parameters. The production of highly oriented fibers was favored by selecting higher extrusion velocity and lower spinneret diameter. A spinneret size of 100 µm and a draw ratio of 6 were sufficient to highly orient the cellulose macromolecules and achieve tenacities above 40 cN/tex (600 MPa). Total orientation assessed via birefringence measurement, tenacity, and Young's modulus values reached a plateau at a draw of 6 and no further development in properties was observed. A temperature of the aqueous coagulation bath of 15 °C slightly promoted greater orientation of the fibers by hampering structural changes of the cellulose macromolecules in the nascent solid fibers. Furthermore, the determination of the elongational viscosity of the liquid thread via the measurement of radial force tensor was tested and showed promising results. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43718.     

新型碳纤维用原丝——高强高模Lyocell纤维纺丝工艺研究

采用天然高相对分子质量纤维素脱脂棉为原料 ,制备了高强高模纤维素纤维 ( L yocell纤维 ) ,并用此作为碳纤维原丝 ,成功制得了强度优于粘胶基碳纤维的 L yocell基碳纤维。考察了高相对分子质量纤维素的溶解特点 ,纺丝工艺对 L yocell纤维聚集态及性能的影响 ,比较了 L yocell纤维和粘胶原丝的表面及截面形态。实验表明 :高相对分子质量纤维素溶解的静溶胀时间和温度对其溶解有明显的影响 ;纺丝过程中 ,大的气隙长度对提高纤维的性能有利 ;随着凝固浴中 N -甲基吗啉 N -氧化物( NMMO )的浓度增加 ,纤维的强度和模量增加 ,当其在凝固浴中的质量分数达到 10 %时 ,强度模量最大 ,浓度继续增加 ,纤维的力学性能开始下降 ;拉伸比增加 ,L yocell纤维的强度模量增加 ,当拉伸比大于 3.0时 ,纤维的性能略有下降     

Preparation and properties of the single‐walled carbon nanotube/cellulose nanocomposites using N‐methylmorpholine‐N‐oxide monohydrate

Single‐walled carbon nanotube (SWNT)/cellulose nanocomposite films were prepared using N‐methylmorpholine‐N‐oxide (NMMO) monohydrate as a dispersing agent for the acid‐treated SWNTs (A‐SWNTs) as well as a cellulose solvent. The A‐SWNTs were dispersed in both NMMO monohydrate and the nanocomposite film (as confirmed by scanning electron microscopy) because of the strong hydrogen bonds of the A‐SWNTs with NMMO and cellulose. The mechanical properties, thermal properties, and electric conductivity of the nanocomposite films were improved by adding a small amount of the A‐SWNTs to the cellulose. For example, by adding 1 wt % of the A‐SWNTs to the cellulose, tensile strain at break point, Young's modulus, and toughness increased ～ 5.4, ～ 2.2, and ～ 6 times, respectively, the degradation temperature increased to 9°C as compared with those of the pure cellulose film, and the electric conductivities at ? (the wt % of A‐SWNTs in the composite) = 1 and 9 were 4.97 × 10^?4 and 3.74 × 10^?2 S/cm, respectively. Thus, the A‐SWNT/cellulose nanocomposites are a promising material and can be used for many applications, such as toughened Lyocell fibers, transparent electrodes, and soforth. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Dry jet‐wet spinning of bagasse/N‐methylmorpholine‐N‐oxide hydrate solution and physical properties of lyocell fibres

Sugarcane bagasse, a cheap cellulosic waste material, was investigated as a raw material for producing lyocell fibers at a reduced cost. In this study, bagasse was dissolved in N‐methylmorpholine‐N‐oxide (NMMO) 0.9 hydrate, and fibers were prepared by the dry jet‐wet spinning method with coagulation in an aqueous NMMO solution. The effects of NMMO in 0 to 50% concentrations on the physical properties of fibers were investigated. The coagulating bath contained water/NMMO (10%) solution produced fiber with the highest drawability and highest physical properties. The cross‐section morphology of these fibers reveals fibrillation due to the high degree of crystallinity and high molecular orientation. In the higher NMMO concentrated baths (30 to 50%), the prepared fibers were hollow inside, which could be useful to make highly absorbent materials. The lyocell fibers prepared from bagasse have a tensile strength of 510 MPa, initial modulus of 30 GPa, and dynamic modulus of approximately 41 GPa. These properties are very comparable with those of commercial lyocell fibers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Rheological aspects of fiber spinning from cellulose solutions in N‐methylmorpholine‐N‐oxide

Based on rheological experiments with a cellulose solution in N‐methylmorpholine‐N‐oxide (NMMO), it was found that the shearing stress generated in the flowing viscoelastic fluid decreases with an l/d ratio in a rheometer capillary. This reduces the elastic response and the outflow of the fluid becomes more uniform. At constant temperature, the elongational viscosity of the solidified stream of the cellulose solution in NMMO is reduced with increase of the deformation rate, which makes it possible to increase the fiber‐formation velocity within the air zone. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1860–1868, 2001     

Methods for reducing the tendency of lyocell fibers to fibrillate

A study has been made of the influence of various process parameters on the fibrillation characteristics of Lyocell fibers, which are spun from a solution of cellulose in N-methylmorpholine-N-oxide (NMMO). The parameters were air gap length, temperature, and humidity; line speed; draw ratio; polymer solution cellulose and water contents; and coagulation bath concentration and temperature. Fibrillation was induced in the fibers by an ultrasonic treatment and compared by defining a fibrillation index from optical micrographs. By selecting combinations of the parameters described above, fibrillation can either be increased or decreased without significantly affecting the tensile properties of the fibers. A method for spinning nonfibrillable filaments on a laboratory scale is presented. © 1996 John Wiley & Sons, Inc.     

Atomic force microscopy of cellulose membranes prepared from the N‐methylmorpholine‐N‐oxide/water solvent system

Cellulose membranes were obtained by solutions of cellulose being cast into a mixture of N‐methylmorpholine‐N‐oxide (NMMO) and water under different processing conditions. Atomic force microscopy (AFM) was used to investigate the surface structures of the membranes. The AFM method provided information on both the size and shape of the pores on the surface, as well as the roughness of the skin, through a computerized analysis of AFM micrographs. The results obtained showed that the surface morphologies were intrinsically associated with the permeation properties. For the cellulose membranes, increasing the NMMO concentration and the temperature of the coagulation bath led to higher fluxes and lower bovine serum albumin rejection. These were always correlated with higher values of the roughness parameters and larger pore sizes of the membrane surfaces. When the cellulose concentration of the casting solution was 11 wt %, the membrane showed a nodular structure with interconnected cavity channels between the agglomerated nodules. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3389–3395, 2002     

纤维素/NMMO溶液及其薄膜的制备与性能研究

以水质量分数为13.3%的N-甲基吗啉-N-氧化物(NMMO)为溶剂溶解棉浆粕,制备质量分数为5%～11%的纤维素/NMMO溶液。将所得溶液制备纤维素薄膜,考察了纤维素/NMMO溶液的稳定性,研究了凝固浴温度和组成对纤维素薄膜的成膜性、断面形态及力学性能的影响。结果表明:纤维素/NMMO溶液随着浓度增大,其粘度先增大后减小,再急剧上升;纤维素/NMMO溶液在玻璃介质中稳定性较好,微量Cu~(2+),Fe~(3+)等杂质存在时,其稳定性显著下降;纤维素薄膜随凝固浴温度升高,其透明性、拉伸强度和断裂伸长率均下降;相对于水,含有乙醇和NMMO的凝固浴能减缓双扩散的速度,使纤维素薄膜的拉伸强度略有提高,断裂伸长率出现不同程度下降。     

Preparation and characterization of dense cellulose film for membrane application

Regenerated cellulose films were prepared with environmentally friendly process by utilized N‐methylmorpholine‐N‐oxide (NMMO)‐Cellulose system. To prepare a dense cellulose film for membrane application, some parameter process which influence porous forming such as cellulose DP, cellulose concentration, addition NMMO in coagulation bath, coagulation bath temperature, and drying condition were investigated. We resumed that the porosity and pore size of cellulose membrane decrease with lower cellulose DP, higher cellulose concentration, addition of NMMO in coagulation bath, applying room temperature in coagulation bath and drying, and applying vacuum on drying process resulted in membranes with porosity in range of 24–41% and pore size 13.4–20.2 nm. The main factor for controlling porosity and pore size of dense cellulose membrane was coagulation process condition especially addition of NMMO into coagulation bath. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Physical agglomeration behavior in preparation of cellulose‐N‐methyl morpholine N‐oxide hydrate solutions by simple mixing

The different melting temperatures of N‐methyl morpholine N‐oxide (NMMO) hydrates in the cellulose–NMMO hydrate solution may be explained by the rather different crystal structures of NMMO hydrates, which are determined by the amount of the hydrates. The preparative process of cellulose–NMMO hydrate solution may result in cellulose structural change from cellulose I to cellulose II, depending on the amount of the hydrate. Mixtures of cellulose and NMMO hydrate in a blender was changed from the granules to slurry with increasing mixing time at 60–70°C, which is below the melting point of the NMMO hydrate. In the case of 15 wt % cellulose–NMMO hydrate granules, which were made by mixing for 20 min, the melting points of various NMMO hydrates were obtained as 77.8°C (n = 0.83), 70.2°C (n = 0.97), and 69.7°C (n = 1.23), respectively, depending on the hydrate number. However, the melting points of cellulose–NMMO hydrate slurry and solution were shifted lower than those of cellulose granules, while the mixing time of slurry and solution are 25 and 35 min, respectively. These melting behaviors indicate instantaneous liquefaction of the NMMO hydrate and the diffusion of the NMMO hydrate into cellulose during mixing in a blender. When cellulose was completely dissolved in NMMO hydrate, the crystal structure of cellulose showed only cellulose II structure. In the cellulose–NMMO products of granules or slurry obtained by high‐speed mixing, which is a new preparation method, they still retained the original cellulose I structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1687–1697, 2004     

High‐strength regenerated cellulose fibers spun from 1‐butyl‐3‐methylimidazolium chloride solutions

High‐performance regenerated cellulose fibers were prepared from cellulose/1‐butyl‐3‐methylimidazolium chloride (BMIMCl) solutions via dry‐jet wet spinning. The spinnability of the solution was initially evaluated using the maximum winding speed of the solution spinning line under various ambient temperatures and relative humidities in the air gap. The subsequent spinning trials were conducted under various air gap conditions in a water coagulation bath. It was found that low temperature and low relative humidity in the air gap were important to obtain fibers with high tensile strength at a high draw ratio. From a 10 wt % cellulose/BMIMCl solution, regenerated fibers with tensile strength up to 886 MPa were prepared below 22 °C and relative humidity of 50%. High strengthening was also strongly linked with the fixation effect on fibers during washing and drying processes. Furthermore, an effective attempt to prepare higher performance fibers was conducted from a higher polymer concentration solution using a high molecular weight dissolving pulp. Eventually, fibers with a tensile strength of ～1 GPa and Young's modulus over 35 GPa were prepared. These tensile properties were ranked at the highest level for regenerated cellulose fibers prepared by an ionic liquid–based process. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45551.     

Modified cellulose fibers prepared by the N‐methylmorpholine‐N‐oxide (NMMO) process

Cellulose fibers with modified properties have been prepared from cellulose solutions in N‐methylmorpholine‐N‐oxide (NMMO). Poly(ethylene oxide) as a hydrophilic modifier and polyethylene as a hydrophobic modifier were added to the spinning solution. Based on microscope examination and measurements of such properties of fibers as porosity, moisture absorption, water retention, and tensile strength, structural changes as well as physical and mechanical properties of the resultant fibers depending on the amount of modifier added to the spinning solution were analyzed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 907–916, 2002     

凝固浴浓度对Lyocell纤维性能及最大纺丝速度的影响

探讨了Lyocell纤维纺丝工艺中凝固浴浓度对最大纺丝速度及纤维相对强度、断裂伸长、初始模量的影响.结果表明:随着凝固浴浓度增大,最大纺丝速度减小;而在凝固浴浓度为10%时,纤维的相对强度和初始模量为最大,延伸度则为最小.     

Blend films of O‐carboxymethyl chitosan and cellulose in N‐methylmorpholine‐N‐oxide monohydrate

To introduce N‐methylmorpholine‐N‐oxide (NMMO) process to prepare antibacterial lyocell fiber, the blend films of O‐carboxymethyl chitosan (O‐CMCS) and cellulose were prepared. O‐CMCS in aqueous suspension with particles having a surface mean diameter of 2.24 μm was blended with cellulose in NMMO hydrate. The blend films with different O‐CMCS content were prepared with the blend solutions. SEM confirmed that O‐CMCS remained within the cellulose film in the particle. The mechanical properties of the blend films show little increased value when O‐CMCS was less 5%; however, it decreased sharply when O‐CMCS was over 8%. Thus, the optimum O‐CMCS content may give a good combination of antibacterial action and mechanical properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4601–4605, 2006     

Hemodialysis membrane prepared from cellulose/N‐methylmorpholine‐N‐oxide solution. I. Effect of membrane preparation conditions on its permeation characteristics

Flat hemodialysis membranes were prepared from cellulose/N‐methylmorpholine‐N‐oxide (NMMO) solutions (dope) with different cellulose concentrations (6–8 wt %) by using a phase‐inversion method. The coagulant used was NMMO aqueous solution, of which the NMMO concentration and its temperature were varied in the range of 0 to 50 wt % and 5 to 60°C, respectively. The effects of these preparation conditions on the permeation characteristics, the ultrafiltration rate (UFR) of pure water, and sieving coefficient (SC) of dextran, were investigated. The decrease in cellulose concentration of the dope and the increases in both temperature and NMMO concentration of the coagulant gave a membrane with high UFR. Concerning the SC, the increase of the cellulose concentration and the decreases in both temperature and NMMO concentration gave a good result. Consequently, the membrane having the preferable UFR and SC as a hemodialysis membrane was obtained when the 8 wt % cellulose dope was coagulated in water at 5°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2302–2307, 2002     

The novel alginate/N‐succinyl‐chitosan antibacterial blend fibers

Alginate/ N‐Succinyl‐chitosan (SCS) blend fibers, prepared by spinning their mixture solution through a viscose‐type spinneret into a coagulating bath containing aqueous CaCl₂, were studied for structure and properties with the aid of infrared spectroscopy (IR) and X‐ray diffraction (XRD). The results indicated a good miscibility between alginate and SCS, because of the strong interaction from the intermolecular hydrogen bonds. The best values of the dry tensile strength and breaking elongation were obtained when SCS content was 30 wt %. The wet tensile strength decreased with the increase of SCS content, and the wet breaking elongation achieved maximum value when the SCS content was 30 wt %. Introduction of SCS in the blend fiber improved water‐retention properties of blend fiber compared to pure alginate fiber. Antibacterial fibers, obtained by treating the fibers with aqueous solution of silver nitrate, exhibited good antibacterial activity to Staphylococcus aureus. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Rheological characterization of cellulose solutions in N‐methyl morpholine N‐oxide monohydrate

Three different modes of rheological properties were measured on 11 and 13 wt % solutions of cellulose in N‐methyl morpholine N‐oxide (NMMO) monohydrate, in which concentration range lyocell fibers of much reduced fibrillation are preferably produced. The dynamic rheological responses revealed that the Cox–Merz rule did not hold for these cellulose solutions. Both cellulose solutions showed a shear thinning behavior over the shear rate measured at 85, 95, 105, and 115°C. However, 13 wt % solution gave rise to yield behavior at 85ºC. The power law index ranged from 0.36 to 0.58. First normal stress difference (N₁) was increased with lowering temperature and with increasing concentration as expected. Plotting N₁ vs shear stress (τ_ω) gave almost a master curve independent of temperature and concentration, whose slope was about 0.93 for both cellulose solutions over the shear rate range observed (τ_ω > 500 Pa). In addition, the cellulose solutions gave high values of recoverable shear strain (S_R), ranging from 60 to 100. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 216–222, 2002     

Hemodialysis membrane prepared from cellulose/N‐methylmorpholine‐N‐oxide solution. II. Comparative studies on the permeation characteristics of membranes prepared from N‐methylmorpholine‐N‐oxide and cuprammonium solutions

Two kinds of regenerated cellulose membranes for hemodialysis were prepared from casting solutions of N‐methylmorpholine‐N‐oxide (NMMO) and cuprammonium (denoted NMMO membranes and cuprammonium membranes, respectively). The concentration of cellulose in the casting solution investigated was 6–8 wt %. The permeation characteristics of both membrane series were compared in terms of the ultrafiltration rate (UFR) of pure water, the sieving coefficient (SC) of dextran, and the solute permeabilities of urea, creatinine, and vitamin B₁₂. The UFR and SC of the NMMO membranes were strongly affected by the cellulose concentration of the casting solution, and NMMO was a preferable solvent for the production of cellulose membranes with high performance; the cuprammonium solution gave low‐performance membranes. The pore structures of both types of membranes were estimated with the Hagen–Poiseuille law. The results showed that the NMMO membranes had larger pore radius and smaller pore numbers than the cuprammonium membranes. The differences in the membrane pore structures led to the differences in the performance between the two membrane series. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 333–339, 2003     

Numerical investigation of spinneret geometric effect on spinning dynamics of dry‐jet wet‐spinning of cellulose/[BMIM]Cl solution

In this study, the effect of spinneret geometry, including the entrance angle α of the entrance channel, the length L_s, and the diameter D₀ of the exit channel, on the spinning dynamics of dry‐jet wet‐spinning of cellulose/1‐butyl‐3‐methylimidazolium chloride ([BMIM]Cl) solution was simulated by using finite element method. Based on the mathematical model of dry‐jet wet‐spinning established in our previous work (Xia et al., Cellulose 2015, 22, 1963) the radial and axial profiles of velocity, pressure, and shear rate in the spinneret and the profiles of diameter, temperature, and tensile stress in the air‐gap region were obtained. From the simulated profiles, the effect of spinneret geometric parameters on the flow behavior and the pressure drop of polymer solution in the spinneret and the die‐swell ratio near the spinneret was discussed. The entrance angle α of the entrance channel mainly influences the flow behavior of polymer solution in the spinneret and the die‐swell effect near the spinneret. As the decrease of the entrance angle α of the entrance channel, the vortices in the spinneret could be removed and the die‐swell ratio decreases. The increase of the length L_s of the exit channel results in the increase of pressure drop in the spinneret and the decrease of the die‐swell ratio. It is also found that the increase of the diameter D₀ of the exit channel reduces the flow velocity of polymer solution and decreases the pressure drop in the spinneret at a constant mass flow rate. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43962.     

Physical properties of lyocell fibers spun from different solution‐dope phases

The hydration number (n) of NMMO hydrates has a significant effect on the rheological properties and phase of the cellulose solutions in the hydrates. The physical properties of the lyocell fibers spun from the cellulose solutions in NMMO hydrates with different values of n were investigated relative to the phase of the solution dope. NMMO hydrate with n = 1.1 could not fully dissolve cellulose, resulting in a heterogeneous solution. NMMO hydrate with n = 0.72 produced a mesophase solution that exhibited a good spinnability. When NMMO hydrates with n = 0.72 and 1.0 were used, the lyocell fiber spun from 15 wt % solution dope gave higher tensile strength than that spun from 12 wt % solution dope. NMMO hydrate with n = 1.0 produced a lyocell fiber whose tensile strength was slightly affected by spin–draw ratio but the tensile strength of the lyocell fiber prepared from NMMO hydrate with n = 0.72 was monotonically increased with increasing spin–draw ratio. Further, the latter gave higher birefringence. The lyocell fiber spun from 15 wt % solution in NMMO hydrate with n = 0.72 produced finely fibrillated structures. When treated with sonic wave the lyocell fiber prepared from 15 wt % cellulose (DP_w 940) solution in NMMO hydrate with n = 0.72 yielded the most serious fibrillation on the fiber surface. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 981–989, 2002