Effect of wall conductances on hydromagnetic flow and heat transfer in a rotating channel

Summary Wall conductance effects on the hydromagnetic flow and heat transfer between two parallel plates in a rotating frame of reference has been studied when the liquid is permeated by a transverse magnetic field. An exact solution of the governing equations has been obtained. It is found that the velocity, current density and the temperature depend only on the sum of the wall conductances ₁ + ₂ = but magnetic field depends on the individual values of ₁ and ₂, where ₁ and ₂ are respectively the wall conductance ratios of the upper and lower walls.

---

Einfluß der Wandleitfähigkeit auf die hydromagnetische Strömung und den Wärmeübergang in einem rotierenden Kanal

Zusammenfassung In der Arbeit wird der Einfluß der Leitfähigkeit der Wände auf die MHD-Strömung sowie auf den Wärmeübergang untersucht für den Fall, daß sich das zähe Medium zwischen zwei rotierenden Platten befindet und ein Magnetfeld parallel zur Rotationsachse angelegt wird. Es wird eine exakte Lösung des Problems gegeben. Es zeigt sich, daß die Geschwindigkeit, die Stromdichte und die Temperatur nur von der Summe der Leitfähigkeiten der Wände + ₂ = abhängen, dagegen hängt die magnetische Feldstärke von den individuellen Werten ₁ und ₂ ab, wobei ₁ und ₂ die Leitfähigkeiten der oberen bzw. unteren Wand bezeichnen.

---

---

With 5 Figures     

Universality and the scaling laws in the superfluid phase transition of3He-4He mixtures

From the second-sound velocityU ₂ near the superfluid transition point, the superfluid densities in³He-⁴He mixtures, _s (X) and _s (), were deduced along the paths of constant³He concentrationX and of constant chemical potential difference of³He and⁴He. The following critical exponents of _s are determined: (a) =XX for _s (X) in the(X, T) plane,(b) X for _s (X) in the(, T) plane, and(c) for _s () in the(, T) plane. It is found that and _X change by about 4–6% relative to with increasing³He concentration up toX=0.4 and by 8–10% up toX=0.53. It seems that, belowX=0.53, universality hold for . Values of have been found to be in good agreement with the critical exponent of _s in pure⁴He under constant pressure. The values of and _X forX0.53 are also found to be consistent with the scaling relations in the (,T) plane of³He-⁴He mixture.Work performed in part while at the Electrotechnical Laboratory.     

Critical Behavior and Scaling of Confined 3He-4He Mixtures

When helium is confined to a uniform small dimension L, its behavior is modified due to the limitation of the growth of the correlation length. This has been explored for planar confinement over a wide range of L. Less is known about confined mixtures, especially in the case of the specific heat. Here two principal effects come into play: the magnitude of the correlation length increases, and the measured heat capacity C_px must be converted to C_p, where = ₃ – ₄ , before finite-size scaling predictions can be verified. The increase in makes a given confinement L look smaller as the concentration x is increased. This, as well as changes of L itself, can be used to test predictions of correlation-length scaling. We report measurements of the specific heat of confined mixtures and compare with the well established scaling for the pure system.     

The critical curve in an antiferromagnetic superconductor with nonmagnetic impurities

The critical curve of a transition of the second kind in an antiferromagnetic superconductor (AFS) with nonmagnetic impurities has been studied. The AFS is described by using the mean-field model given by Nass, Levin, and Grest and assuming a one-dimensional electron band. We find that the points on the critical curve satisfy the thermodynamic stability condition for 0₁/₀5.04 and 0.49H_Q/₀1.64.Here ₁ is the inverse lifetime of a conduction electron for nonmagnetic impurity scattering,H _Q is the antiferromagnetic molecular field, ₀ is the zero-temperature order parameter of a superconductor in the absence ofH _Q and impurities. Further, ₁ and H_Q denote the values of these quantities for points on the critical curve. For ₁/₀>5.04 and H_Q/₀>1.64, the phase transition from the superconducting to the normal state is always of the second kind. Some thermal properties of the system near the critical curve have also been investigated and we find that these depends dramatically on the impurity concentration.     

Rheological properties of aqueous silicon nitride suspensions

The effect of surface modification of Si₃N₄ particle on the colloidal behavior and the rheological properties of aqueous Si₃N₄ suspensions under steady and oscillatory conditions are investigated in detail. Due to the decrease of the oxidizing level, the isoelectric point (IEP) of the modified particle shifts to basic region gently. Attempts have been made to apply rheological models to the suspensions with various solid volume fraction (). For the as-received suspensions, the Sisco model provides the best fit in the range of 0.30 while the Casson model in 0.35 0.45. The shear behavior of modified suspensions fits to Sisco model in the range of 0.40 and Casson model in 0.45 0.54. The rheological behavior of modified suspensions is improved efficiently. The critical strain decreases and the linear viscoelastic regime narrows continuously with increasing solid concentration. For the modified suspensions, the linear viscoelastic regime broadens and the corresponding elastic modulus decreases sharply. With increasing solid concentration, the characteristic frequency shifts toward lower frequencies and the suspension transforms from more viscous to more elastic.     

An extension of the theory of oscillating cup viscometers

The theory of the fluid motion in the interior of an oscillating or rotating cup is reexamined. The quantity of interest in viscometry is the torque exerted by the fluis on the sides and rims of the cup. In this paper expressions for the torque are obtained for geometries for which the cup height approaches a fluid boundary layer thickness. Interest in such geometries is due to viscosity measurements made in mixtures in the critical region where cups of small height are used in order to minimize gravity effects.Nomenclature D() Torque on the cup, Eq. (5) - E() Truncation error term, Eq. (24) - h Internal half-height of a filled cup or the height of the liquid in a partially filled cup - I Moment of inertia of cup and suspension system - I Moment of inertia of fluid inside cup - I _n Modified Bessel function of order n - J _{i, n} Defined in Eq. (13) - R Radius of the cup - S _n Defined in Eq. (7) - S _n Defined in Eq. (10) - x Variable 2 ₀/ - z Variable 2 ₀^1/2 - () Angular displacement of the cup - Boundary layer thickness - Logrithmic decrement - Laplace transform variable - ₀ Dimensionless height h/ - Frequency ratio / ₀ - Kinematic viscosity - ₀ Dimensionless radius R/ - Density of liquid - Dimensionless time ₀ t - Phase angle of oscillation - Angular frequency of oscillation with liquid present in cup - ₀ Angular frequency of oscillation in a vacuum     

An unusual behavior in the melting region of isotactic polypropylene crystals revealed by temperature-modulated DSC

We present a new method to analyze irreversible transformation kinetics of melting in polymer crystals with temperature modulated differential scanning calorimetry (TMDSC). In the melting region of several polymers, the apparent heat capacity obtained with TMDSC can be expressed as C _s + (|F _melt|/)/(1 + i ()), with the true heat capacity,C _s, the endothermic heat flow of melting,F _melt, the angular frequency of temperature modulation, , and the mean time of melting of each crystallite, , depending on the underlying linear heating rate, . In the case of isotactic polypropylene, the frequency dependence cannot be approximated by this formula. The dependence suggests the possibility of the retardation in the melting kinetics to follow temperature modulation.     

Kondo Impurity in a Mesoscopic Ring: Charge Persistent Current

We study the influence of a magnetic impurity or ultrasmallquantum dot on the charge persistent current of a mesoscopicring. The system consists of electrons in a one-dimensionalring threaded by spin-dependent Aharonov–Bohm/Casher fluxes,coupled via an antiferromagnetic exchange interaction to alocalized electron. By passing to a basis of electron stateswith definite parities, the problem is mapped onto a Kondomodel for the even-parity channel plus free electrons in theodd-parity channel. The twisted boundary conditionsrepresenting the fluxes couple states of opposite parityunless the twist angles satisfy =f,where f are integers, with spin index=, . For these special values of, the model is solved exactly by a Bethe ansatz.Special cases are investigated in detail. In particular weshow that the charge stiffness in the case= is insensitive to the presenceof the magnetic impurity/quantum dot.     

Heat transfer of a semitransparent plate under conditions of a regular regime of the second kind

The kinetics of the cooling of a plane semitransparent layer under conditions of a regular regime of the second kind is analyzed.Notation time - T temperature - T_e temperature of the surrounding medium (the ambient temperature) - T° initial temperature of the layer - h_e coefficient of convective heat exchange - x coordinate - coefficient of absorption of the substance - n index of refraction - B(, T) surface density of radiation of a black body - C bulk specific heat - K thermal conductivity - wavelength of the radiation - _t range of wavelengths in which the material is partially transparent - _op range of wavelengths in which the material is opaque - degree of blackness of the surfaces in the range of _op - R() coefficient of reflection from the inner surfaces of the layer - ⁺ intensity of the rays consisting of acute angles with the inner normal to the surface x = 0 - ^– intensity of rays in the opposite direction - q thermal flux - angle measured from the inner normal to the surface x = 0 Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 41, No. 3, pp. 541–546, September, 1981.     

Disappearance of Bose-Glass Behavior in Transport Properties of YBa2Cu3O y Films with Columnar Defects

The glass transitions of the vortex system in Au-ion irradiated YBa₂Cu₃O _y films have been studied by the measurements of transport properties as a function of magnetic field B and angle of B to the direction of columnar defects. At =0°, we find an anomalous upturn behavior of the glass transition line B _g(T) at BB /3, where B is the matching field. In B>B /3, the dependence of glass transition temperature T _g reveals cusplike behavior with a peak at =0°, which is consistent with the Bose glass theory. In B<B /3, on the other hand, T _g is almost independent of , suggesting the system undergoes the vortex glass transition induced by the inherent point-like defects.     

Dielectric properties of chemically treated wood

Dielectric properties along the grain for absolutely dried untreated and seven kinds of chemically treated Sitka spruce (Picea sitchensis Carr.) woods were measured. Cole-Cole's circular arc law was applied to the results of the relaxation due to the motions of methylol groups. The following changes were caused by chemical treatments. In polyethylene glycol (PEG) impregnation, the distribution of relaxation times became very narrow, the generalized relaxation time (_m) was considerably decreased, and the relaxation magnitude (₀ – ) was slightly increased. In acetylation, the distribution of relaxation times became very broad, _m was considerably increased, and (₀ – ) was remarkably decreased. In propylene oxide treatment, the distribution of relaxation times became slightly narrow and _m was decreased. _m was slightly decreased in formalization, phenol-formaldehyde (PF) resin treatment and wood methyl methacrylate (MMA) composite. (₀ – ) was decreased in formalization and PF-resin treatment and was hardly changed in wood-MMA composite and heat treatment. The distribution of relaxation times was almost unchanged in formalization, PF-resin treatment, wood-MMA composite and heat treatment.     

Particle packing and rheological property of highly-concentrated ceramic suspensions: φm determination and viscosity prediction

A model is proposed which is able to predict the maximum particle packing density (_m) over a wide variety of ceramic suspensions with very large difference in particle size/shape, particle surface chemistry, and solvent chemistry. This model provides a simple method to obtain _m directly through the use of a few viscosity-concentration data for a given colloidal suspension, rather than a best-fitting approach. The model is also capable of predicting the viscosity of a variety of ceramic suspensions under different conditions of shear. A comparison with some existing viscosity model is also presented.     

Short-range and long-range forces on a common basis in quantum crystals

A theory is developed which allows the determination of the ground-state energy and the phonons of quantum crystals on an equal footing in the collective picture. The central quantity required to dress the lines of the diagrams of the phonons as well as those of the kinetic and potential energy is the phonon self-energyM(). It is approximated in a systematic way, giving the force constants:M()M. This theory is in contrast to those using theT-matrix theory. We show that use of theT-matrix as an effective interaction in phonon calculations leads to an inconsistency.     

Conformational and electronic band structure analysis of a new type of high performance polybenzothiazole polymers

The energy-band structure and preferred (minimum energy) conformation of the recently synthesized polybenzothiazoles (PBT; AA and AB type), representing a new class of high-performance polymers, were determined by molecular orbital calculations. In the case of the AAPBT chain, the most stable conformation was obtained at ₁ (rotation angle about the bond joining the two bibenzothiazole moieties) = 20° and ₂ (rotation angle about the bond joining the bibenzothiazole group and thep-phenylene group) = 10°. In the case of the ABPBT chain, the corresponding minimum energy rotational angle () was found to be 20°. These conformations agree fairly well with both theoretical and experimental observations. The calculated axial band gaps were 1.94 and 2.08 eV for the AAPBT and ABPBT polymers, respectively, and these values are close to the corresponding value for polyacetylene, considered a prototype electrically-conducting polymer because of its novel electronic properties and manifold applications.     

Rubber toughening of plastics

Creep measurements were made on a series of six ABS blends containing 0 to 20 vol% of 80m glass beads. At small strains, the beads raised the modulus of the ABS. However, debonding of the polymer from the glass resulted in a rapid drop in modulus with increasing strain and bead content, and at strains above 1.0% the order of stiffnesses was reversed. Debonding resulted in an increase in creep rate with, as measured by the time to reach 1% volume strain. Plots of In ^–1 against applied stress were linear, in accordance with the Eyring equation, and provided data for comparing stress concentration factors. The relationship between and fitted approximately to the Ishai Cohen effective area model. It is concluded that debonded glass beads accelerate multiple crazing by increasing average stresses in the ABS matrix, and in that respect resemble rubber particles. However, unlike rubber particles, debonded beads drastically reduce notched Charpy impact strength.     

Computation of particle settling speed and orientation distribution in suspensions of prolate spheroids

A numerical technique for the dynamical simulation of three-dimensional rigid particles in a Newtonian fluid is presented. The key idea is to satisfy the no-slip boundary condition on the particle surface by a localized force-density distribution in an otherwise force-free suspending fluid. The technique is used to model the sedimentation of prolate spheroids of aspect ratio b/a=5 at Reynolds number 03. For a periodic lattice of single spheroids, the ideas of Hasimoto are extended to obtain an estimate for the finite-size correction to the sedimentation velocity. For a system of several spheroids in periodic arrangement, a maximum of the settling speed is found at the effective volume fraction (b/a)²04, where is the solid-volume fraction. The occurence of a maximum of the settling speed is partially explained by the competition of two effects: (i) a change in the orientation distribution of the prolate spheroids whose major axes shift from a mostly horizontal orientation (corresponding to small sedimentation speeds) at small to a more uniform orientation at larger , and (ii) a monotonic decrease of the the settling speed with increasing solid-volume fraction similar to that predicted by the Richardson–Zaki law (1–)⁵⁵ for suspensions of spheres.     

Fourier transform of the Morse-V DD potential

The Fourier transform (k) of the Morse-V _DD potential is derived analytically. An expansion of (k) valid for smallk is given and comments are made about the occurrence of both even and odd powers ofk in the expansion.     

Analysis of the effect of the decomposition of char-forming heat-insulating materials on the free discharge of a gas mixture

The article presents results of a numerical solution of a nonsteady problem on the free discharge of a mixture of gases from a hemispherical volume with allowance for thermal decomposition of heat-insulating materials.Notation V volume - S area - t - P p - T - u v - Q q, dimensional and dimensionless time, pressure, temperature, TIM decomposition rate, and heat flux - adiabatic exponent - R gas constant - density - H specific enthalpy - c specific heat - thermal conductivity - , , _s dimensionless complexes - coefficient expressing the radiative properties of the gas medium and the heat-transfer surface - Stefan-Boltzmann constant Indices 0 initial state and scale factors - s surface - coke - M TIM material - P pyrolysis front - A ablation front - v volatile degradation products - adiabatic conditions - c completion of discharge Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 54, No. 5, pp. 787–793, May, 1988.     

Structure of unidimensional temperature stresses

Using the structural approach, the temperature stresses are examined in a semiinfinite rod, insulated on the lateral faces and rigidly fixed at the end. A comparative analysis is made for three heat-transfer models.Notation k(t) heat flux relaxation function - (t) internal energy relaxation function - T rod temperature - ambient temperature - t time - x coordinate along the rod - _xx(x, t) stress - u(x, t) displacement - (x, t) deformation - c₀=(E/)^1/2 speed of sound in the rod under isothermal conditions - E elasticity modulus - density of the material - _t coefficient of thermal expansion - thermal-conductivity coefficient - a thermal-diffusivity coefficient - b thermal-activity coefficient - c_q=(a/_r)^1/2 velocity of heat propagation - _r heat flux relaxation time - (t) unique Heaviside function Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 33, No. 5, pp. 912–921, November, 1977.     

Interfacial spring model for ultrasonic interactions with imperfect interfaces: Theory of oblique incidence and application to diffusion-bonded butt joints

The quasi-static distributed spring model is used to derive the ultrasonic reflectivity of an imperfectly-bonded interface as a function of frequency and angle of incidence. The results are then incorporated in a model for the corner reflection from a diffusion-bonded joint between two abutting plates, the corner being defined by the bond plane and the common lower surface plane of the plates. An immersion-inspection geometry is assumed, and seven categories of corner reflections are identified and examined in detail. These fall into two classes: those having parallel incident and exiting rays in water (=), and those having nonparallel water rays ( ). The = categories are suitable for single probe (pulse-echo) inspections of the joint. Based on the amplitude of the outgoing corner-reflected signal, two = geometries appear promising. These employ, respectively, a corner reflection involving only longitudinal waves with the interface illuminated at near-grazing incidence (LLL), and a corner reflection involving only transverse waves with the interface illuminated at near 45° incidence (TTT). In addition, two practical geometries are indicated; these both involve mode conversion upon reflection from the interface, with the incident or outgoing longitudinal wave traveling nearly parallel to the interface. Model predictions for LLL and TTT reflections are compared to measurements on diffusion-bonded Inconel specimens, and techniques for applying the model results to more complicated bond geometries are discussed.