Highly Efficient Room Temperature Synthesis of Silver‐Doped Zinc Oxide (ZnO:Ag) Nanoparticles: Structural,Optical, and Photocatalytic Properties

Synthesis of silver‐doped zinc oxide (ZnO:Ag) nanoparticles through precipitation method has been reported. The synthesis was conducted at room temperature and no subsequent thermal treatment was applied. ZnO nanoparticles were characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), X‐ray photoelectron spectroscopy (XPS), fourier transmission infrared spectroscopy (FTIR), and ultraviolet‐visible (UV–Vis) spectroscopy. Detailed crystallographic investigation was accomplished through Rietveld refinement. The effect of silver content on structural and optical properties of resultant ZnO nanoparticles has been reported. It was found that silver doping results in positional shifts for the XRD peaks and the absorption band edge of ZnO. These were attributed to the substitutional incorporation of Ag⁺ ions into Zn²⁺ sites within the ZnO crystal. In addition, higher silver incorporation resulted in smaller size for ZnO nanoparticles. The photocatalytic activity of the ZnO:Ag nanoparticles was also determined by methylene orange (MO) degradation studies and compared to that of undoped ZnO. Improved photocatalytic activity was obtained for ZnO:Ag nanoparticles. It has been shown that an optimum amount of silver dopant is required to obtain maximum photocatalytic activity.     

Silver-zinc oxide nanocomposite: From synthesis to antimicrobial and anticancer properties

A green method by Verbascum speciosum was used to synthesize zinc oxide nanoparticles (ZnO NPs). ZnO NPs were coated with silver to synthesize Ag–ZnO nanocomposite (NCs). The physicochemical properties of Ag–ZnO NCs were analyzed by Fourier-transform infrared spectroscopy (FTIR), powder X-ray diffraction (PXRD), field emission scanning electron microscope (FESEM), transmission electron microscopy (TEM), dynamic light scattering (DLS), and zeta potential. The FTIR indicated the peak of Zn–O vibration and some hydroxyl and carboxyl groups. PXRD analyses confirmed the synthesis of ZnO NPs and Ag–ZnO NCs. Due to the size of the crystallite obtained from PXRD, solid-phase sizes (from FESEM and TEM images), and dynamic sizes from DLS, agglomeration was observed. The Ag–ZnO NCs showed a negative charge surface (?49.3 mV). Ag–ZnO NCs had a high antibacterial activity towards two most important infectious bacteria (i.e., Escherichia coli and Staphylococcus aureus) and anticancer activity against human liver-carcinoma cells (HepG2). Later, it depended on time and concentration of Ag–ZnO NCs. The cytotoxicity properties of Ag–ZnO NCs were also studied against NIH-3T3 as a normal cell, where the results verified the lower cell toxicities of nanocomposite than the HepG2.     

Nanoparticles of ZnO and Mg-doped ZnO: Synthesis,characterization and efficient removal of methyl orange (MO) from aqueous solution

Nanoparticles of zinc oxide and of ZnO doped with MgO in different concentrations (1, 2 and 4 mol%) were synthesized in a controlled and reproducible way, using the Pechini polymer precursor method. To determine the physicochemical and structural characteristics of the synthesized nanoparticles, Fourier transform IR (FTIR), X-ray diffraction (XRD), UV–Vis spectroscopy and transmission and scanning electron microscopy (TEM and SEM) were used. Characterization revealed the particles obtained to be nanometric in size (<50 nm) and with a deformed hexagonal morphology. Taking into account the doping percentage, the energy gap value varied between 3.3 eV for pure ZnO and 3.45 eV for ZnO with 4 mol% of Mg, which indicates that the optical properties of these nanoparticles were affected by dopant concentration. The effect of doping with Mg²⁺ on the capacity for removal of pollutant molecules by ZnO, for different working conditions, was evaluated by studying the removal of methyl orange (MO) in aqueous solution. Irradiation of the compounds led to a greater removal of MO from the solution such that all ZnO samples doped with MgO showed higher photoactivity than ZnO. The ZnO nanoparticles doped with 2% Mg were the most efficient in removing MO, achieving a removal percentage of ~73% after 2 h of testing and a totally transparent solution after 3 h of treatment. The kinetics of removal of MO promoted by this sample was best represented by pseudo-first-order kinetics. The results of this work showed that on combining a photosensitive semiconductor, ZnO, with a wide band gap insulator, MgO, Zn–Mg solid solutions are obtained that showed adequate capacity to remove contaminating organic molecules, specifically MO.     

Structural,optical, cytotoxicity,and antimicrobial properties of MgO,ZnO and MgO/ZnO nanocomposite for biomedical applications

In this study, MgO nanoparticles were successfully fabricated and incubated inside ZnO NPs to form MgO/ZnO nanocomposite for biomedical applications. The x-ray diffraction analysis of MgO, ZnO, and MgO/ZnO has shown the single-phase x-ray diffraction patterns through X'pert High score. The crystallite sizes were calculated as 18 nm, 42 nm, and 53 nm, respectively. The average particle size of MgO, ZnO, and MgO/ZnO nanopowders depicted from secondary electron images of field emission electron microscopy were 56 nm, 400 nm, and 450 nm, respectively. The presence of MgO NPs inside ZnO NPs was confirmed by transmission electron microscopy. The elemental dispersive spectroscopy of MgO, given the peaks of oxygen and magnesium, also showed only zinc and oxygen peaks in ZnO, which confirms no other impurities in MgO and ZnO powders. The elemental analysis of MgO/ZnO nanocomposite showed the peaks of Zinc and Oxygen, along with a tiny peak of Mg. The photoluminescence and UV–vis spectroscopy revealed the absorbance fluorescence limit of the nanomaterials. Fourier transform infrared spectroscopy confirmed the several groups present in the nanocomposite. The biocompatibility of MgO, ZnO, and MgO/ZnO was observed with human peripheral blood mononuclear cells. The cytotoxicity studies were also performed against human cancer (liver and breast) cell lines. The MgO, ZnO, and MgO/ZnO exhibited the antimicrobial properties against Escherichia coli and Staphylococcus aureus.     

Acetone sensing and modeling through functionalized Ag-catalysts and CNTs via low cost metal-organic framework-derived ZnO nanostructures

Cost-effective synthesis, portability, quick response and fascinating features of semiconducting metal oxide sensors have drawn much accredited to be utilized in wide variety of potential sensing applications. Herein, flexible acetone sensor was fabricated through spray coating method using different conductive inks of carbon nanotubes (CNTs), zinc oxide (ZnO) and silver (Ag) nanoparticles solutions on cellulose paper. Morphological analysis revealed the fiber like morphology of cellulose over which CNTs, ZnO and Ag nanoparticles are uniformly distributed. The energy dispersive X-ray spectroscopic analysis was performed to observe the elemental composition in the as-prepared samples. The recovery time toward acetone was greater for CNTs/Ag acetone sensor at 95% as compared to CNTs/ZnO/Ag sensor. Additionally, sensing time of the samples towards acetone was measured and the observed response time was greater for CNTs/ZnO/Ag (0.52 s) acetone sensor as compared to CNTs/Ag sensor (0.41 s). Hence, CNTs/ZnO/Ag can be easily employed for sensing applications due to quick response.     

Green synthesis,characterization and antimicrobial activity of carbon quantum dots-decorated ZnO nanoparticles

In this research, ZnO nanoparticles (ZnO NPs) and Carbon Quantum Dots-decorated ZnO nanoparticles (ZnO/CQDs NCs) were prepared via different procedures and precursors. Soya chunk was applied as a source of carbon for the preparation of CQDs. Crystalline structure, purity, size, and morphological properties of products were investigated via X-ray diffraction (XRD) analysis, energy dispersive spectroscopy (EDS), Transmission Electron Microscopy (TEM), FT-IR, and Scanning Electron Microscopy (SEM) respectively. Findings showed that homogeneity, size, and morphological properties of products can be intensively affected via different precursors and procedures. From the homogeneity, size, and morphological point of view, the hydrothermal route, ammonia, 5 h, and 180 °C were the optimum procedure, pH adjuster, temperature, and time respectively. Optimum product was applied for carrying out minimum inhibitory concentration (MIC) and Agar disk-diffusion tests against various microorganisms. Results demonstrated that prepared ZnO NPs have maximum antibacterial activity against Staphylococcus aureus (19.53 μg/ml) and ZnO/CQDs NCs have no inhibitory effect against tested microorganisms. For ZnO NPs, the disk diffusion test proved that the highest growth inhibition zone was related to Staphylococcus aureus (15 mm). The presence of CQDs in ZnO/CQDs NCs reduces the inhibitory effect of ZnO NPs intensively.     

In situ preparation of Au or Ag nanoparticles in the presence of hyperbranched poly(amidoamine)s with hydrophobic end‐groups as nanoreactors and reductants

Hyperbranched poly(amidoamine)s with methyl ester terminals (HPAMAM‐COOCH₃) were used as nanoreactors and reductants to prepare gold or silver nanoparticles (Au NPs or Ag NPs). HPAMAM‐COOCH₃ could bind AuCl₄ ⁻ (or Ag⁺) and then reduce AuCl₄ ⁻ (or Ag⁺) into Au NPs (or Ag NPs) through their internal amines, while the external methyl ester groups prevented the aggregation of polymers. The formation of Au NPs or Ag NPs was verified using transmission electron microscopy (TEM), ultraviolet‐visible spectroscopy (UV‐Vis), X‐Ray powder diffraction (XRD), Fourier‐transform infrared spectroscopy (FT‐IR), and thermogravimetric analysis (TGA), confirming the formation of Au NPs or Ag NPs with small particle size and low size distribution.POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Structural and electrical properties of ZnO:Ag core-shell nanoparticles synthesized by a polymer precursor method

Monodispersed core-shell type ZnO:Ag nanoparticles were synthesized by a polymer precursor method and their structural and electrical properties were reported in detail. The synthesis technique involves a sol-gel type chemical reaction between aqueous solutions of poly-vinyl alcohol (PVA), sucrose and Zn²⁺ salt. The Zn²⁺-PVA-sucrose polymer precursor powders so obtained after the reaction was further explored for the synthesis of ZnO:Ag nanoparticles. The key part of the work lies in the use of polymer coated ZnO nanoparticles as templates to obtain the ZnO core-Ag shell type nanostructures. Structural and spectroscopic analyses of the derived samples were performed with X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The XRD patterns of the ZnO:Ag nanoparticles consist of distinct peaks corresponding to the hexagonal wurtzite type (space group P63mc) crystal structure of ZnO along with the typical peaks of face centered cubic crystal structure of metallic silver. EDS and XPS analyses confirmed the chemical composition and surface structure of the core-shell nanoparticles. Microstructural analysis revealed the monodispersed platelet shaped ZnO nanoparticles with a thin layer of Ag coating on the surface. UV–visible diffuse reflectance studies revealed the effects of Ag coating on the optical properties of the samples. Detail analysis of the dielectric properties of the samples were performed as a function of frequency (1 Hz to 10 MHz) and temperature (300–528 K) to investigate the electrical conduction mechanism in the samples.     

Green synthesis of Ag/ZnO nanohybrid using sodium alginate gelation method

Mesoporous Ag/ZnO nanohybrid material has been successfully synthesized using simple and green route via sodium alginate media. The as-synthetized nanomaterial was structurally characterized using various techniques such as X-ray powder diffraction (XRD), scanning and transmission electron microscopy (SEM and TEM), Fourier transform infrared (FTIR), thermogravimetric analysis (TGA) and N₂ adsorption-desorption measurements (BET). The Ag/ZnO nanoparticles were quasi-spherical, crystalline with a size ranging from 40 to 50 nm. In addition, characterization results confirmed that calcined Ag/ZnO nanomaterial sample was stable and mainly consisting of both hexagonal ZnO and cubic silver nanoparticles.     

Simultaneous coloration and functional finishing of cotton fabric using Ag/ZnO nanocomposite

In this study, colored cotton fabric with special functions, including self‐cleaning, anti‐bacterial, and ultraviolet (UV) blocking were prepared by applying zinc oxide as a photocatalyst and using silver nanoparticles as both a novel class of colorant for coloration and an agent capable of modifying the zinc oxide nanoparticles. The homogenous distribution of Ag/ZnO nanocomposite on the fibre surface was confirmed by field emission scanning electron microscopy (FE‐SEM), Energy‐dispersive X‐ray spectroscopy (EDS) and X‐ray mapping. X‐ray diffraction patterns showed the presence of the nanocomposite on the treated cotton fabric. The results indicated that adding silver nanoparticles to zinc oxide led to better self‐cleaning properties, even the photocatalytic activity of ZnO had no negative effect on fabric colour. Moreover, this process imparted proper anti‐bacterial properties and UV‐blocking activity to cotton fabrics.     

Photocrosslinkable acid urethane dimethacrylates from renewable natural oil and their use in the design of silver/gold polymeric nanocomposites

Castor oil-based acid urethane macromers were prepared and employed for obtaining Ag/Au/polymer nanocomposites. Structure and UV induced photopolymerization of the macromers were investigated by spectral methods. The polymerization rate and the degree of conversion decreased with about 10% in the presence of 2.5 wt.% silver nanoparticles (Ag NPs). For the diacid macromer, the surface plasmon intensity increased with irradiation time (the optical density of the absorption maximum (430 nm) attained 2.3 after 600 s), whereas a diminished efficiency was found for Ag NPs in situ generated. Transmission electron microscopy and X-ray photoelectron spectroscopy confirmed uniform distribution of the spherical nanoparticles (0.6 nm (Ag NPs); 5 nm (Au NPs)) and the appearance of Ag 3d_3/2, Ag 3d_5/2, Au 4f_7/2 and Au 4f_5/2 peaks corresponding to Ag (0) or Au (0). Environmental scanning electron microscope with energy-dispersive X-ray detector, contact angle and mechanical parameters measurements complemented the above observations.     

Preparation and Characterization of Gelatin Nanofibers Containing Silver Nanoparticles

Ag nanoparticles (NPs) were synthesized in formic acid aqueous solutions through chemical reduction. Formic acid was used for a reducing agent of Ag precursor and solvent of gelatin. Silver acetate, silver tetrafluoroborate, silver nitrate, and silver phosphate were used as Ag precursors. Ag⁺ ions were reduced into Ag NPs by formic acid. The formation of Ag NPs was characterized by a UV-Vis spectrophotometer. Ag NPs were quickly generated within a few minutes in silver nitrate (AgNO₃)/formic acid solution. As the water content of formic acid aqueous solution increased, more Ag NPs were generated, at a higher rate and with greater size. When gelatin was added to the AgNO₃/formic acid solution, the Ag NPs were stabilized, resulting in smaller particles. Moreover, gelatin limits further aggregation of Ag NPs, which were effectively dispersed in solution. The amount of Ag NPs formed increased with increasing concentration of AgNO₃ and aging time. Gelatin nanofibers containing Ag NPs were fabricated by electrospinning. The average diameters of gelatin nanofibers were 166.52 ± 32.72 nm, but these decreased with the addition of AgNO₃. The average diameters of the Ag NPs in gelatin nanofibers ranged between 13 and 25 nm, which was confirmed by transmission electron microscopy (TEM).     

Green Synthesis of Zinc Oxide Nanoparticles (ZnO NPs) for Effective Degradation of Dye,Polyethylene and Antibacterial Performance in Waste Water Treatment

At present, there is a vital need for river water purification by developing new approaches to eliminate bacterial biofilms, textile dyes, and Low-Density Polyethylene (LDPE) plastics that pose severe threats to human and environmental health. The current work put forward the construction of an eco-friendly green strategy to synthesize zinc oxide nanoparticles (ZnO NPs) using areca nut (Areca catechu) extract and their application to tackle the challenges in water purification. Prepared biogenic NPs were characterized by X-ray diffraction analysis (XRD), Fourier Transform Infra-Red (FT-IR), Energy Diffraction Spectroscopy (EDS), Scanning Electronic Microscopy (SEM), Transmission Electron Microscopy (TEM) analysis, confirmed the spherical shape in 20 nm and UV–vis spectroscopy. The characteristic absorption band exhibited at 326 nm confirmed the formation of ZnO NPs using UV–vis spectroscopy. Among all the tested bacterial pathogens, the E. coli at 50 µg/mL concentration showed the highest inhibition of biofilm activity, followed by the highest growth curve, cellular leakage, and potassium ion efflux. The ZnO NPs observed with photo-degradation of Rhodamine-B (Rh-B), Methylene Blue (MB), and Nigrosine dyes under sunlight irradiation at different time intervals. Finally, the photocatalytic activity of LDPE-ZnO NPs nanocomposite film showed the highest degradation under solar light irradiation were confirmed through photo-induced weight loss, SEM, FTIR, and MALDI-TOF analysis. This study demonstrates ZnO NPs exhibit efficacy against biofilm formation, degradation of photocatalytic textile dyes, and low-density LDPE film under solar light irradiation, which can be a step forward in water purification.

     

Biosynthesized Ag–ZnO nanohybrids exhibit strong antibacterial activity by inducing oxidative stress

We report facile biosynthesis of Ag–ZnO nanohybrids consisting of Ag nanoparticles decorated ZnO nanobullets prepared by decorating wet chemically synthesized ZnO nanobullets with Ag nanoparticles through bioreduction of Ag ⁺ ions with aqueous extract of Piper nigrum fruits. The prepared nanomaterials were well characterized by FESEM, TEM, HRTEM, EDX, XRD, XPS, PL and UV–vis spectroscopy. FESEM and TEM analyses on the nanohybrids revealed ∼18 nm Ag nanoparticles decorating ZnO nanobullets with average size ∼48 nm. XRD results revealed hexagonal wurtzite ZnO with 22.4 nm crystallite size and FCC Ag with 18.7 nm crystalline size. Ag–ZnO nanohybrids exhibited strong antibacterial action against Escherichia coli, Bacillus oceanisediminis and Pseudomonas entomophila and efficiently inhibited their growth at 100 μg/mL, 50 μg/mL and 125 μg/mL, respectively. The molecular basis of antibacterial action of Ag–ZnO nanohybrids against E. coli was investigated using different biochemical and molecular assays. Addition of antioxidant histidine suppressed the antibacterial action of Ag–ZnO nanohybrids towards E. coli due to its ROS scavenging action. Bradford assay results showed enhanced protein leakage from Ag–ZnO nanohybrids treated E. coli, while TBARS assay results confirmed lipid peroxidation triggered by ROS. SEM on Ag–ZnO nanohybrids treated E. coli confirmed significant damage to the cell wall leading to morphology change. The antibacterial activity of Ag–ZnO nanohybrids against E. coli is mainly due to the ROS-induced oxidative stress, which caused enhanced lipid peroxidation, cell wall damage leading to significant protein leakage and DNA fragmentation.     

Structural,optical, thermoelectrical,and magnetic study of Zn1‐xCoxO (0 ≤ x ≤ 0.10) nanocrystals

In this work, we have prepared Co‐doped ZnO nanocomposites by zinc nitrate and cobalt sulfate as new precursors via the coprecipitation method and the samples were followed to identify the morphological, optical, structural, and magnetic properties. The XRD patterns revealed the crystalline nature of nanoparticles with hexagonal wurtzite structures, which meant that Co impurity did not disturb the structure of pure ZnO and the minimum crystallite size of nanoparticles was calculated to be around 37 nm. The XRD patterns also showed the lattice parameter increase owing to the incorporation of a Co dopant. The TEM results revealed the sphere‐like particles whose size varied between 56 and 88 nm in diameter at a 4% level of impurity. DRS analysis identified that the band gap energy decreased from 3.18 eV for the pure substance to 2.36 eV for the 10% impure substance. VSM analysis exhibited that the saturation magnetization value increased to 8.4 × 10^?3 emu/g for the highest Co content of 10%, which indicated the ferromagnetic behavior of NPs.     

Green Chemical Synthesis of Silver Nanoparticles and its Catalytic Activity

Silver nanoparticles (Ag(0) NPs) were synthesized by the chemical reduction method, in which ceftriaxone (antibiotic) used as reducing (to convert Ag⁺ to Ag(0)) and capping agent. UV–Visible spectroscopy revealed the first indication of formation of Ag(0) NPs. FT-IR spectroscopy showed the interaction of formation of bonding between antibiotic standard and silver. X-ray powder diffraction powder pattern confirmed the crystalline nature of prepared Ag(0) NPs. These Ag(0) NPs were used as catalyst for three organic hazardous chemicals i.e., 4-nitro-1,3-Phenylene diamine, 6-methyl-2-nitroanilline, 4-methyle-2-nitroanilline. The prepared Ag(0) NPs showed good catalytic activity against these compounds.     

The preparation,characterization, and properties of silver nanoparticle reinforced reduced graphene oxide–poly(amidoamine) nanocomposites

A simple approach was employed to synthesize silver nanoparticle (Ag NP) reinforced reduced graphene oxide–poly(amidoamine) (Ag‐r‐RGO–PAMAM) nanocomposites. The structural changes of the nanocomposites with the PAMAM and Ag NPs were confirmed by Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, X‐ray diffraction, Raman spectroscopy, and scanning electron microscopy. In addition, the performance was characterized with thermogravimetric and electrical conductivity instruments. The results indicate that the Ag NPs are well dispersed in fine size on the surface of the RGO–PAMAM composites, which results in an increase of at least 38% in thermostability and a certain enhancement in electrical conductivity. It is worth noting that the electrical conductivity of the nanocomposites was approximately 5.88 S cm^?1, which was higher than that of RGO–PAMAM, and increases with the rising content of silver nanoparticles. Meanwhile, the Ag‐r‐RGO–PAMAM nanocomposites still maintain a favorable dispersion in organic solvents. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45172.     

Optimizing the structural and photocatalytic performance of Ag-decorated ZnO/Zn(OH)2 nanoparticles for RhB degradation

In this study, as-prepared and Ag-decorated ZnO/Zn(OH)₂ composite nanoparticles (NPs) were obtained using the sol–gel technique. First, the effect of aging on the structural, optical, and morphological features was examined. Ag NPs can interact with the electronic structure of ZnO/Zn(OH)₂ NPs, resulting in changes in their energy levels. It was found that the composite NPs obtained after 6 h solution aging increased in full width at half maximum and good crystallinity of the structures from the X-ray diffraction (XRD) measurements. The Raman spectrum supports the experimental data obtained from XRD and Fourier transform infrared, a material containing a mixture of ZnO and Zn(OH)₂. From the morphological study, Ag NPs were successfully decorated on the ZnO/Zn(OH)₂ surface, and composite NPs did not change the morphological appearance of the structure. Second, the photocatalytic performance of the samples was investigated. In the experimental setting, ultra-violet A light was employed as the irradiation source, whereas rhodamine B (RhB) was used as the dyestuff. The photo-degradation of the RhB dyestuff on composite NPs was observed to be 98.5% and 92.5% for 6 and 2 h aged samples, respectively. On Ag NPs, the catalytic performance of the sample was increased up to 95% after 180 min.     

Optical and electrical properties of p-type Ag-doped ZnO nanostructures

Zn_1−xAg_xO nanoparticles (NPs) (x=0, 0.02, 0.04, and 0.06) were synthesized by a sol–gel method. The synthesized undoped ZnO and Zn_1−xAg_xO-NPs were characterized by X-ray diffraction analysis (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and UV–visible spectroscopy. The XRD patterns indicated that undoped and Ag-doped ZnO crystallize in a hexagonal wurtzite structure. The TEM images showed ZnO NPs with nearly spherical shapes, with particle size distributed over the nanometer range. Evidence of dopant incorporation is demonstrated in the XPS measurements of the Ag-doped ZnO NPs. The Raman measurements indicated that the undoped and Ag-doped ZnO-NPs had a high crystalline quality. From the result of UV–vis, the band-gap values of prepared undoped and Ag-doped ZnO were found to decrease with an increase in Ag concentration. The obtained undoped and Ag-doped ZnO nanoparticles were used as a source material to grow undoped and Ag-doped ZnO nanowires on n-type Si substrates, using a thermal evaporation set-up. Two probe method results indicated that the Ag-doped ZnO nanowires exhibit p-type properties.     

Synergistic antimicrobial effects of polyaniline combined with silver nanoparticles

Silver/polyaniline nanocomposites (Ag NPs/PANI) containing PANI nanofiber and Ag nanoparticles were synthesized by one-step approach without using any extra reducing agent or surfactant and applied to new antimicrobial agents. Morphologies and crystallinity of the nanocomposites were characterized with SEM and XRD. The results showed that the average diameter of the PANI nanofibers is around 50–150 nm, and the average particle size of Ag NPs is around 100 nm. The crystallinity of PANI gets better with increasing silver nitride concentration. UV–vis absorption spectroscopy analysis indicated that the Ag NPs have some effect on the microstructure of PANI. The antimicrobial properties of Ag NPs/PANI against Gram-negative Escherichia coli, Gram-positive Staphylococcus aureus and fungous Yeast were evaluated using viable cell counts. The test results demonstrated that Ag NPs/PANI have enhanced antimicrobial efficacy compared to that of pure Ag NPs or pure PANI under the same test condition. The mechanism of the synergistic antimicrobial effect of Ag NPs with PANI was also proposed. In addition, thermal gravity analysis indicated that pure PANI and Ag NPs/PANI exhibit better thermal stability. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012