Biotransformation of Carbon Tetrachloride and Anaerobic Granulation in a Upflow Anaerobic Sludge Blanket Reactor

Carbon tetrachloride (CT) in a synthetic wastewater was effectively degraded in a 2?l upflow anaerobic sludge blanket reactor during the granulation process by increasing the chemical oxygen demand (COD) and CT loadings. The effect of operational parameters such as influent CT concentrations, COD, CT loading, food to mass (F/M) ratio, and specific methanogenic activity (SMA) were also detected during granulation. Over 97% of CT was removed at 37°C, at a COD loading rate of 10?g/L?day. Chemical oxygen demand and CT removal efficiencies of 92 and 88% were achieved when the reactor was operating at CT and COD loading rates of 17.5?mg/L?day and 12.5?g/L?day, respectively. This corresponds to an hydraulic retention time of 0.28?day and an F/M ratio of 0.57?g?COD/g?volatile?suspended?solids?(VSS)?day. In 4?weeks, the seed sludge developed the CT degrading capability that was not very sensitive to shocks. The granular sludge cultivated had a maximum diameter of 2.5?mm and SMA of 1.64?g?COD/g?VSS?day. Glucose biodegradation by CT acclimated anaerobic granules was expressed with competitive inhibition. However the competitive inhibition was not significant since the competitive inhibition coefficient (Ki) was as high as 18.72?mg/L. Kinetic coefficients of k (maximum specific substrate utilization rate), Ks (half velocity coefficient), Y (growth yield coefficient), and b (decay coefficient) were determined as 0.6/day, 1.1?mg/L, 0.23?g?VSS/g glucose-COD, and 0.01/day, respectively, based on growth substrate glucose–COD during CT biotransformation. The CT was treated via biodegradation and this contributed to 89% of the total removal. The removal contributions from biomass adsorption, abiotic transformation, and volatilization were negligible. Adsorption and volatilization accounted for only 0.8 and 0.5% of the total removal, respectively.     

Combined System for Biological Removal of Nitrogen and Carbon from a Fish Cannery Wastewater

A combined system composed of three sequentially arranged reactors, anaerobic-anoxic-aerobic reactors, was used to treat the wastewater generated in the tuna cookers of a fish canning factory. These wastewaters are characterized by high chemical oxygen demand (COD) and nitrogen concentrations. The anaerobic process was performed in an upflow anaerobic sludge blanket reactor operated in two steps. During Step I different influent COD concentrations were applied and organic loading rates (OLRs) up to 4 g COD/(L?d) were achieved. During Step II hydraulic retention time (HRT) was varied from 0.5 to 0.8 days while COD concentration in the influent was constant at 6 g COD/L. The OLRs treated were up to 15 g COD/(L?d). When HRTs longer than 0.8 days were used, COD removal percentages of 60% were obtained and these values decreased to 40% for a HRT of 0.5 days. The denitrification process carried out in an upflow anoxic filter was clearly influenced by the amount of carbon source supplied. When available carbon was present, the necessary COD/N ratio for complete denitrification was around 4 and denitrification percentages of 80% were obtained. The nitrification process was successful and was almost unaffected by the presence of organic carbon (0.2–0.8 g TOC/L), with ammonia removal percentages of 100%. Three recycling ratios (R/F) between the denitrification and nitrification reactors were applied at 1, 2, and 2.5. The overall balance of the combined system indicated that COD and N removal percentages of 90% and up to 60%, respectively, were achieved when the R/F ratio was between 2 and 2.5.     

High-Rate Biodegradation of Phenol by Aerobically Grown Microbial Granules

This study demonstrates that aerobic granules can be developed to achieve high phenol loading rates in a sequencing batch reactor. The reactor was started at a loading rate of 1.5 kg?phenol?m?3?d?1 with phenol-enriched activated sludge as inoculum. Granules first appeared on Day 9 after startup and quickly grew to become the dominant biomass in the reactor. The phenol loading was then adjusted stepwise to a final value of 2.5 kg?phenol?m?3?d?1. At this high loading, phenol was completely degraded and high biomass concentration was maintained in the reactor. The biomass continued to possess a good settling ability, with a sludge volume index of 60.5 mL?g?SS?1 (SS stands for suspended solids). Granules remained stable, without significant deterioration in granule structure and physiology, even at the maximum phenol loading rate tested. The applied selection pressure enabled the micro-organisms to aggregate into granules, and the compact structure of the aerobic granules served both to retain biomass and protect the microbial cells against the phenol toxicity. High specific phenol degradation rates exceeding 1 g?phenol?g?VSS?1?d?1 (VSS stands for volatile suspended solids) were sustained up to phenol concentrations of 500 mg?l?1, and significant rates continued to be achieved up to a phenol concentration of 1,900 mg?L?1. The phenol-degrading aerobic granules can be exploited to design compact high-rate aerobic granulation systems for the treatment of industrial wastewaters containing high concentrations of phenol and other inhibitory chemicals.     

Enhancement of Denitrification in Upflow Sludge Bed Reactors with Sludge Wasting

From the performance data of the upflow sludge bed (USB) reactors (with sufficient carbon), the rate-limiting step in denitrification is nitrate reduction. Biological denitrification in the USB reactors (superficial velocity=0.5, 1.0, 2.0, and 4.0 m/h) can be greatly enhanced with sludge wasting from the bioreactor [i.e., maintain granular sludge retention time (GSRT) at 20 days], including high volumetric loading rates of up to 6.61 g NO3?–N/L day, high specific denitrification rates [arithmetic mean=0.31–0.42 g NO3?–N/g volatile suspended solids (VSS) day], high denitrification efficiencies (97.6–97.8%), and relatively low washout rates of biomass granules (arithmetic mean ω?=0.13–0.31 g VSS/L day). The biomass concentration, average granule size (dp), and microbial density of the USB reactors with sludge wasting were greater than those of the USB reactors without sludge wasting (i.e., the former grew more compact granules than the latter). From the granulation experiment, the granule size distribution and dp of the broken-up granules in the sludge-bed zone can restore to those of the original granules in one GSRT, implying that spontaneous flocculation of extra-cellular polymer of denitrifying-bacteria cells occurred in the USB reactor, which may also be accelerated by a rigorous backing-mixing effect of continuous production of biogas. Accordingly, the USB reactor with sludge wasting can be regarded as a promising alternative to treat high-strength nitrate wastewater.     

Formation of Aerobic Granules with Domestic Sewage

The use of aerobic granules in wastewater treatment can reduce the land area that is needed for the treatment of sewage. Until now granulation has been mainly studied using artificial wastewater. Studying the possibility of forming aerobic granules on domestic sewage in a sequencing batch reactor was a logical step in the scaling-up process and development of this technology. Therefore, aerobic granulation was studied using presettled sewage as influent. After 20?days of operation at high chemical oxygen demand (COD) loading heterogeneous aerobic granular structures were observed, with a sludge volume index after 10?min settling of 38?mL?g?1 and an average diameter of 1.1?mm. Applying a high COD load was found to be a critical factor for the formation of aerobic granules on this type of influent. Therefore short cycle times and concentrated wastewater are preferred to form granules in a sequencing batch reactor when low strength wastewater is used. The nutrient removal was not optimized in this study.     

Anaerobic Degradability: Effect of Particulate COD

Batch bioassay tests were conducted to evaluate the effect of particulate chemical oxygen demand (COD) (CODP) on anaerobic digestion of wastewater at different ratio of food to microorganism (F/M). Synthetically prepared soluble and complex wastewaters were used. Experiments were conducted in seven sets of serum bottles maintained at F/M ranging from 0.18 to 2.0. Each set contained six bottles having a total COD (CODT) of 500 mg and CODP from 0 to 100%. Methane generation conforms to the first order rate kinetics. At all F/M, k?(day?1) decreased linearly with increase in fraction of CODP?(CODPF = CODP/CODT). Biomethane potential (BMP), and substrate and sludge activities also exhibited declining trend with increasing CODPF. The optimum value of F/M ranged from 0.57 to 0.68. The two variables, CODPF and F/M, were compounded to yield the ratio of CODP to microorganisms [M, measured as volatile suspended solids (VSS)]. On increasing the CODP/VSS from 0 to 0.9, the rate constant for methane generation is reduced by 81%. BMP30, percent sludge activity, and substrate utilization rate are lowered by 52–55%. These correlations could serve as useful guidelines to quantitatively assess the impact of particulate COD on biodegradability parameters.     

Enhanced Biological Phosphorus Removal Performance and Microbial Population Changes at High Organic Loading Rates

A laboratory-scale sequencing batch reactor was operated and the dynamics of Rhodocyclus-related phosphorus-accumulating organisms (PAOs) population was monitored. After the system reached a steady state and showed a stable enhanced biological phosphorus removal status, the organic loading rate was increased from 160 to 1,020?g?COD?m?3?cycle?1 in five steps. When the P storage capacity reached maximum at 330?g?COD?m?3?cycle?1, the system lost the stability and the effluent phosphorus concentration fluctuated. As the organic loading rate increased from 160 to 1,020?g?COD?m?3?cycle?1, the PAO population decreased from 83.8±4.9 to 32.2±16.2% and internal polyphosphate content decreased from 0.20 to 0.03?mg?P?mg?VSS?1. Phosphate-accumulating metabolism was weakened as the organic loading rate increased and PAO population decreased concomitantly, whereas glycogen-accumulating metabolism increased at high organic loading rates as supported by the increased intracellular glycogen content and production of a higher fraction of intracellular poly-β-hydroxyl valerate.     

Comparative Study between a Hybrid System and a Biofilm System for the Treatment of Ammonia and Organic Matter in Wastewaters

The efficiency of two similar gas-lift bioreactors, a biofilm reactor and a hybrid circulating floating bed reactor (CFBR), were studied and compared. In the biofilm CFBR the biomass grew preferably adhered on a plastic granular support, whereas in the hybrid CFBR both suspended biomass and biofilms were allowed to grow in the reactor. COD/NH4+ ratio (COD=chemical oxygen demand) was manipulated between 0.0 and 8.0?g/g, maintaining the ammonia influent concentration around 50?mg N–NH4+/L, the ammonia loading rate at 0.9?kg N–NH4+/m3?day and the hydraulic retention time at 1.36?h. At low COD/NH4+ ratio (0 and 0.5?g/g) both systems behaved similarly, achieving ammonia removal percentages higher than 95%. In the biofilm CFBR a reduction of the nitrification percentage from 95 to 20% was observed when a COD/N–NH4+ ratio up to 8?g/g was applied in the influent. However, at the same operational conditions, the nitrification process in the hybrid CFBR was slightly affected. In the hybrid-CFBR reactor heterotrophs growing in suspension consumed the COD source faster than those growing in biofilms as was monitored. The growth of heterotrophic microorganism in suspension had a beneficial effect for the nitrifying population growing in the biofilm of the hybrid CFBR. Nitrifying activity of the biofilm was not limited by the presence of heterotrophs consuming dissolved oxygen, displacing the nitrifying bacteria or creating mass transfer resistance as was observed in the biofilm CFBR.     

Methanogenic Characteristics of Formate-Utilizing Sludge

The formate-utilizing sludge was first enriched in a chemostat reactor for over 90 days; at steady state, the sludge yield averaged 0.066 mg volatile suspended solids (VSS)∕mg chemical oxygen demand (COD). The methanogenic characteristics of this sludge were then investigated in three series of batch experiments at 37°C using formate, acetate, and H2∕CO2, individually, as substrates. At pH 6.4–8.0, the formate-degrading rate averaged 0.76 mg∕mg VSS∕h (6.35 mg COD∕mg VSS∕d). At pH 3.0, the sludge completely lost its bioactivity, and required a lengthy recovery period to regain a fraction of its bioactivity after the pH was adjusted to pH 7.1. The sludge was also able to utilize H2∕CO2 as substrate at an average rate of 0.0167 mg H2∕mg VSS∕h (3.21 mg COD∕mg VSS∕d). At pH ≤ 8.0, the sludge degraded acetate at a very low rate of 3.0 μg∕mg VSS∕h (0.077 mg COD∕mg VSS∕d). The sludge exhibited a slight homoacetogenic activity at pH > 8.0 using formate as substrate; the homoacetogenic reaction using H2∕CO2 as substrate was thermodynamically infeasible, according to chemical free energy analysis.     

Effect of Increasing Nitrobenzene Loading Rates on the Performance of AMBR and Sequential AMBR/CSTR Reactor System

A laboratory scale sequential anaerobic migrating blanket reactor (AMBR)/aerobic completely stirred tank reactor (CSTR) system was operated to investigate the effect of increasing nitrobenzene (NB) concentrations on the performance of AMBR/CSTR reactor system. The reactor system was operated at increasing NB loading rates from 1.93?to?38.54?g?NB?m?3?day?1 and at a constant hydraulic retention time of 10.38?days. In this study, chemical oxygen demand (COD) and NB removal efficiencies, variations of bicarbonate alkalinity (Bic.Alk.), total volatile fatty acid (TVFA), and total methane gases were monitored. COD removal efficiencies were 93–94% until a NB loading rate of 5.78?g?m?3?day?1 in the AMBR reactor. For maximum COD removal, the optimum NB loading rate and NB concentration were found to be 5.78?g?m?3?day?1 and 60?mg?L?1, respectively. COD removal efficiencies decreased from 94 to 87% and to 85% at NB loading rates of 1.93–28.90 and 38.54?g?m?3?day?1, respectively. COD was mainly removed in the first compartment. NB removal efficiencies also were approximately 100% at all NB loading rates in the effluent of the AMBR reactor. The maximum total gas and methane gas productions were found to be 2.8?L?day?1 and 1.3?mL?day?1, respectively, at a NB loading rate of 5.78?g?m?3?day?1. The TVFA concentration in the effluent of AMBR was low (17?mg?L?1) at a NB loading rate as high as 38.54?g?m?3?day?1. Overall COD removal efficiencies were found to be 99 and 96% at NB loading rates of 1.93 and 38.54?g?m?3?day?1, respectively, in a sequential AMBR/CSTR reactor system. In this study, NB was reduced to aniline under anaerobic conditions. Aniline removal efficiencies were 100% until a NB loading rate of 17.34?g?m?3?day?1 in aerobic CSTR reactor while aniline removal efficiency decreased to 90% at a NB loading rate of 38.54?g?m?3?day?1 in an aerobic reactor. In the aerobic step, aniline was mineralized to catechol. The contribution of aerobic step is not only the degradation of aniline, it may also increase the COD removals from 85 to 99% at a NB loading rate as high as 38.54?g?m?3?day?1.     

Effect of Organic Loading Rate on Aerobic Granulation. II: Characteristics of Aerobic Granules

Four sequential aerobic sludge blanket reactors, Reactors R1, R2, R3, and R4, were operated at organic loading rates (OLRs) of 1, 2, 4, and 8?kg chemical oxygen demand (COD)/m3?day, respectively. Aerobic granules were not detected at the low OLRs in R1 and R2. Aerobic granules first appeared on Day 14 in Reactor R3, operating at a moderate OLR of 4?kg COD/m3?day. Aerobic granules were initially observed on Day 18 in R4, operating at the highest OLR tested of 8?kg COD/m3?day. These granules were unstable and disintegrated within 2 weeks after their first appearance. Under the OLR of 4?kg COD/m3?day, the process of aerobic granulation could be clearly divided into three phases of acclimation, multiplication, and maturation, with specific granular growth rates (ν?) of 0.1081, ?0.0064, and ?0.0008?day?1, respectively. The values of ν? became smaller with time, and indicated that the aerobic granules had stabilized. Compared to the looser and more amorphous flocs, the compact granules in Reactor R3 possessed a higher specific gravity of 1.064, a higher strength with an integrated coefficient of 99.5%, a higher cell surface hydrophobicity of 75%, and a higher ratio of polysaccharides (PS) to proteins (PN) at 5.0?mg PS per mg PN.     

Acidification of Lactose in Wastewater

Acidification of lactose in wastewater was conducted in four series of experiments in an upflow reactor to investigate individual effects of hydraulic retention time (HRT) (2–24 h), lactose concentration in wastewater (2–30 g COD∕L), pH (4.0–6.5), and temperature (20°–60°C). Optimum acidification was found at pH 5.5 and 55°C. Acidification increased with HRT, but with the decrease of lactose concentration in wastewater. Degradation of lactose followed the Michaelis-Menten model with a maximum specific degradation rate of 4.39 g∕g VSS?day and a half-rate concentration of 1.97 g∕L. Production of volatile fatty acids, in general, favored lower lactose concentrations and higher pH, but was not sensitive to HRT and temperature. Distribution of individual volatile fatty acids∕alcohols was dependent on lactose concentration, pH, and temperature, but less sensitive to HRT. Under most conditions acetate, propionate, and ethanol were the predominant products. Biogas produced under all test conditions was composed of mostly hydrogen and carbon dioxide, but no detectable methane. Sludge yield was estimated as 0.230 ± 0.021 g VSS∕g COD.     

Aerobic Methane Oxidation Coupled to Denitrification: Kinetics and Effect of Oxygen Supply

Aerobic methane oxidation coupled to denitrification (AME-D) is a process in which aerobic methanotrophs oxidize methane and release organic compounds that are used by coexisting denitrifiers as electron donors for denitrification. This process is potentially promising for denitrification of wastewater or landfill leachate poor in organic carbon using methane produced onsite as external electron donor. We studied the kinetics of an aerobic methane-oxidizing denitrifying culture and investigated the effect of dissolved oxygen (DO) concentration and air supply rate on AME-D using a batch reactor and a semicontinuous reactor setup. At methane concentrations of 18–33% in air and air flow rates of 15–35?mL?air?L?1?liquid?min?1, the DO concentration was less than 0.01?mg?L?1 and the nitrate removal reached a maximum value of 56.7?mg?NO3–N?g?1?VSS?d?1 with 79% being attributed to denitrification. When the air supply rate was increased to 70?mL?air?L?1?liquid?min?1 resulting in a drop in methane content to 10%, the DO concentration in the bioreactor rose to about 0.8–1.0?mg?L?1 and the total nitrate removal dropped to about 10?mg?NO3–N?g?1?VSS?d?1 with none of it being attributed to denitrification.     

Biodegradation of Phenol with Wastewater as a Cosubstrate in Upflow Anaerobic Sludge Blanket

Anaerobic degradation of phenol mixed with a readily degradable synthetic wastewater (DSWW) as a cosubstrate was studied in a 12?L upflow anaerobic sludge blanket reactor at 30±2°C over a period of 632?days. DSWW was prepared by diluting sugar cane based molasses. The biomass was acclimatized to high phenol concentration by gradually decreasing the DSWW chemical oxygen demand (COD) of 4,000?mg/L. Feed made up of phenol COD and DSWW COD in the ratio of 7:3 (phenol concentration = 1,176?mg/L) was successfully treated at a hydraulic retention time (HRT) of 12?h and organic loading rate (OLR) of 8?g?COD/L?day. Phenol removal ranged from 99.9 to 84% at phenol COD varying from 10 to 70% in the feed. During the entire operation, COD removal varied from about 74 to 91.3%. The influent COD was distributed into CH4–COD ( ～ 72%), effluent COD ( ～ 17%), and sludge and unaccounted COD ( ～ 11%). The process failure occurred at 4:1 phenol COD: DSWW COD. Specific methanogenic activity of granular sludge exhibited uniform activity up to phenol COD of 70%. The performance of the reactor could not be maintained beyond 70% phenol COD even by reducing the sludge loading rate, increasing HRT, or decreasing OLR.     

Sludge Production and Settleability in Biofilm-Activated Sludge Process

The sludge production and settleability have been estimated experimentally in a completely mixed biofilm-activated sludge reactor (hybrid reactor). A steady-state hybrid reactor was run at different stages of suspended biomass concentration (X) under constant values of influent substrate concentration (So) and hydraulic retention time (HRT). The values of X were gradually decreased in these stages until the system completely washed out of the suspended biomass and converted to pure biofilm reactor. As a result, the role of biofilm in the treatment gradually increased with an increase in the effluent substrate concentration (S). The experiment was supported by a mathematical expression for describing the sludge yield in the system under the previous conditions. The experimental and theoretical studies in the present work reveal that there is a critical phase of the hybrid system at which the system produces a high rate of excess sludge. That critical phase is found at a specific ratio between the suspended and the attached growth. Avoiding that critical phase enables the sludge production in the hybrid reactor to be reduced and optimized. Further, the minimum sludge production was found when the biofilm is theoretically inactive for chemical oxygen demand (COD) removal (S相似文献   

UASB Treatment of Tapioca Starch Wastewater

Feasibility of the upflow anaerobic sludge blanket (UASB) process was investigated for the treatment of tapioca starch industry wastewater. After removal of suspended solids by simple gravity settling, starch wastewater was used as a feed. Start-up of a 21.5-L reactor with diluted feed of approximately 3,000 mg∕L chemical oxygen demand (COD) was accomplished in about 6 weeks using seed sludge from an anaerobic pond treating tapioca starch wastewater. By the end of the start-up period, gas productivity of 4–5 m3/m3r?day was obtained. Undiluted supernatant wastewater with a COD concentration of 12,000–24,000 mg∕L was fed during steady-state reactor operation at an organic loading rate of 10–16 kg COD/m3r?day. The upflow velocity was maintained at 0.5 m∕h with a recirculation ratio of 4:1. COD conversion efficiencies >95% and gas productivity of 5–8 m3/m3r?day were obtained. These results indicated that removal of starch solids from wastewater by simple gravity settling was sufficient to obtain satisfactory performance of the UASB process.     

Combined Removal of Carbon and Nitrogen in an Integrated UASB-Jet Loop Reactor Bioreactor System

An innovative anaerobic–aerobic integrated bioreactor system consisting of an upflow anaerobic sludge blanket (UASB) and a jet loop reactor was developed to investigate the feasibility of combined removal of carbon and nitrogen for a low-strength wastewater at different hydraulic retention times (HRTs) and recycle ratios. Total chemical oxygen demand (COD) removal of the integrated system increased from 87 to 92%, at a combined system HRT of 44?h, when the recycle ratio was increased from 100 to 400%, respectively. Denitrification efficiency of the integrated system increased from 49 to 86%, at all HRTs, when the recycle ratio was increased from 100 to 400%. The integrated system, on average, achieved more than 78% of total nitrogen at all HRTs. Nitrogen content of the biogas produced from the UASB reactor increased with increase in recycle ratios while the methane content exhibited a reverse trend, irrespective of the HRTs. Sludge volume index of the UASB reactor increased from 15?to?42?mL/g total suspended solids at the end of the study. Specific methanogenic activity of the granular sludge decreased from 1.3 to 0.8 g CH4–COD/g volatile suspended solids per day at the end of the study. Nitrogen and COD mass balance of the integrated system indicated that a substantial amount of influent nitrogen and COD was lost in the effluent as dissolved form.     

Experimental Validation of the Static Granular Bed Reactor for Industrial Waste Anaerobic Treatment

The static granular bed reactor (SGBR) is a unique high-rate anaerobic reactor designed to operate in a simple downflow manner, offering high chemical oxygen demand (COD) removal efficiencies (greater than 90%) resulting from high biomass retention in the system. A study was performed to evaluate the SGBR versus a control system, the upflow anaerobic sludge blanket (UASB) reactor, and to evaluate performance idiosyncrasies of the SGBR and the control. The two reactors were operated at three different hydraulic retention times (HRTs): 8, 16, and 24 h. The reactors treated synthetic wastewater, intended to simulate food industry waste, composed of sucrose and nonfat dry milk. Overall, COD removal was higher for the SGBR than for the UASB reactor. In particular, at a HRT of 8 h, the SGBR achieved a COD removal of 90.7% and the UASB reactor reduced the COD concentration by 77.5%. The UASB reactor’s specific COD loading factor proved rate limiting with values ranging from 0.19 to 0.94?gCOD/(gVS?d) versus 0.11 to 0.34?gCOD/(gVS?d) for the SGBR. A tracer study idealized hydraulics within the two systems, and the results showed minimal dead volume and 4–6% short circuiting for both reactors.     

Operational Optimization and Mass Balances in a Two-Stage MBR Treating High Strength Pet Food Wastewater

A two-stage membrane bioreactor (MBR) system was evaluated for the treatment of high strength pet food wastewater characterized by oil and grease, chemical oxygen demand (COD), biochemical oxygen demand (BOD)5, total suspended solids (TSS), total Kjeldahl nitrogen (TKN), NH4–N, and TP concentrations of 2,800, 25,000, 10,000, 4,500, 1,650, 1,300, and 370?mg/L, respectively, to meet stringent surface discharge criteria of BOD5, TSS, and NH4–N of <10?mg/L, and TP of <1?mg/L. Pretreatment of the dissolved air flotation effluent with FeCl3 at a dose of 3.5?g/L, corresponding to a Fe:P molar ratio of 1.3:1 affected TP, TSS, volatile suspended solids (VSS), COD, BOD5, and TKN reductions of 88, 72, 75, 11, 11, 36, and 17%, respectively. The two-stage MBR operating at a total hydraulic retention time of 5.3?days comprising 2.5?days in the first stage and 2.8?days in the second stage, and solids retention time of 25?days in the first stage consistently met the criteria despite wide variations in influent characteristics. Very high COD and BOD5 removal efficiencies of 97.2 and 99.8% were observed in the first stage, with an observed yield of 0.14?gVSS/gCOD. A modular approach for the quantification of simultaneous nitrification denitrification (SND) in the first-stage MBR was developed and verified experimentally. The model indicated that on average, 21% of the influent nitrogen was removed by SND and predicted nitrogen loss with an accuracy of 72%. Complete nitrification of the residual organic nitrogen and ammonia was achieved in the second-stage MBR.     

Treatment of Landfill Leachate by a Combined Anaerobic Fluidized Bed and Zeolite Column System

The use of a combined anaerobic fluidized bed and zeolite fixed bed system in sanitary landfill leachate treatment was investigated. Anaerobic treatability studies were successfully performed in the anaerobic fluidized bed reactor. The chemical oxygen demand (COD) removal was attained up to 90% with increasing organic loading rates as high as 18?g?COD/L?day after 80?days of operation. Good biogas production yield (Ygas) of 0.53?L biogas per gram removed COD with methane (CH4) content of 75% was obtained. The attached biomass concentration increased along the column height from bottom to top, and its mean value was found 6,065?mg/L after 100?days of operation. The anaerobically treated landfill leachate was further treated by a zeolite fixed bed reactor. While excellent ammonia removal (>90%) was obtained with the untreated zeolite, the regenerated zeolites showed higher performance. Consequently, this combined anaerobic and adsorption system is an effective tool to remove high COD and high ammonia in landfill leachate.