Compositional and structural identification of natural gas hydrates collected at site 1249 on ocean drilling program leg 204

In contrast to the structural studies of laboratory-grown gas hydrate, this study has been performed on naturally grown clathrate hydrates from the sea floor. The PXRD pattern of natural gas hydrate shows that the sample had a structure I hydrate. The¹³C NMR spectrum was obtained for the natural gas hydrate sample in order to identify the cage occupancy of guest molecules and determine the hydration number. The NMR spectrum reveal that the natural gas hydrates used in this study contain only methane with no noticeable amount of other hydrocarbons. The existence of two peaks at different chemical shifts indicates that methane molecules are encapsulated in both large and small cages. In addition, Raman spectroscopic analysis is also carried out to identify natural hydrates and compared with the NMR results. Investigating the composition and structure of natural gas hydrates is essential for applying natural gas hydrates as a novel energy source.     

On the Quantification of Lignin Hydroxyl Groups With 31P and 13C NMR Spectroscopy

Factors affecting the accuracy of the analysis of lignin hydroxyl and carboxyl groups with ³¹P NMR have been further elucidated. Two modifications of ³¹P NMR analysis of lignin, namely the protocols using 1,3,2-dioxaphospholane (PR-I) and 2-chloro-4,4,5,5-tetramethyl-1,3,2-dioxaphospholane (PR-II) as phosphorylation reagents with different internal standards, were studied. The previous ³¹P NMR standard protocol with PR-II underestimated OH groups by about 30%, whereas the ³¹P NMR standard protocol with PR-I tended to produce overestimated data. It has been shown that cholesterol is not an appropriate internal standard, resulting in underestimated values for OH groups due to incomplete baseline resolution. The best internal standard has been found to be endo-N-hydroxy-5-norbornene-2,3-dicarboximide. Strong care should be taken related to the stability of the internal standards to avoid inflated results due to IS degradation. Under modified optimized conditions, both methods show a good correlation with the ¹³C NMR protocol in the quantification of hydroxyl groups as average, with the variability between the methods in the range of 5–15%. However, the ³¹P NMR protocols report COOH content that is twice as low as that of ¹³C NMR data. Finally, the best approach for the use of the ³¹P and ¹³C NMR methods in lignin analysis is discussed.     

Semiquantitative analysis of thiophenic compounds in light cycle oil (LCO) using C NMR spectroscopy

S-methyltetrafluoroborate salts of the thiophenic compounds (CH₃-S⁺:BF₄⁻) present in LCO petroleum fractions were obtained and analyzed by ¹H and ¹³C NMR spectroscopy. The methylation of the samples was carried out using 99.5% ¹³C enriched methyl iodine, to improve the sensitivity of the technique. The amount of the methylated derivatives was determined by the internal standard method; using dioxane as a reference, 37 sulphur compounds were detected. Among them, benzo[b]thiophene, dibenzo[b,d]thiophene, and several isomers of methyl, dimethyl and trimethyl[b]benzothiophenes were the most abundant. With this research, it was demonstrated that NMR spectroscopy can be used to analyze thiophenic compounds from petroleum medium fractions.     

Strain-induced crystallization of natural rubber as studied by high-resolution solid-state C NMR spectroscopy

A series of high-resolution solid-state ¹³C NMR experiments were performed on both unstretched and in situ stretched natural rubber samples. From the ¹³C CP/MAS spectra, it was found that natural rubber does form small crystals at room temperature though the degree of crystallinity is very small. Furthermore, from the ¹³C DD/MAS spectra, the crystalline signals were found to increase with the increase of draw ratio. ¹³C spin-lattice relaxation time (T₁) and ¹H spin-spin relaxation time (T₂) of in situ stretched natural rubber were measured for the first time, which provided further evidences for the conclusion that there exist crystals in both stretched and unstretched natural rubber samples. Quantitative ¹³C NMR measurements indicated that strain-induced crystallization occurs when the draw ratio reaches about 2.0 and the maximum crystallinity of our natural rubber samples can be as high as 19.3% upon stretching.     

13C NMR spectroscopic characterization of trimethylol propane ester lubricants

The ability to identify the different acyl groups present in lubricants composed of mixed acid esters of trimethylol propane by¹³C nuclear magnetic resonance spectroscopy is demonstrated. The technique discriminates between esters with acyl groups containing between 5 and 10 carbon atoms and can be used similarly to identify acyl groups in pentaerythritol or neopentyl glycol ester lubricants.     

Fully quantitative carbon-13 NMR characterization of resol phenol-formaldehyde prepolymer resins

Different resol phenol-formaldehyde prepolymer resins have been synthesized with different Formaldehyde/Phenol (F/P) ratios or different catalysts and characterized by ¹³C NMR spectroscopy in solution. A fast quantitative measuring protocol is proposed based on the use of chromium(III)acetylacetonate as a relaxation agent. APT (attached proton test) and DEPT (distortionless enhancement by polarisation transfer) spectra were acquired to enable proper resonance assignments, especially in the regions with severe signal overlap. Equations are presented in which the methylene bridges (MB), the methylol groups (MG) and the dimethylene ether bridges (DMEB) of resol resins are quantitatively taken into account. Important structural factors determined quantitatively for resol prepolymer resins are the F/P ratio after reaction, the degree of polymerization (n), the number average molecular weight (M_n) and the content of free ortho and para positions.     

Sequence analysis of poly(ethylene/1,4-cyclohexanedimethylene terephthalate) copolymer using H and C NMR

The triad-level sequence analysis of poly(ethylene/1,4-cyclohexanedimethylene terephthalate) copolymer was reported in a solvent system of o-chlorophenol/deuterated chloroform mixture (50/50 v/v) at 80 °C using 600 MHz ¹H NMR. The well-resolved alcoholic CH₂ proton peak of the glycol units was observed, which made the detailed sequence analysis possible. The peaks of the cis- and trans-forms of the 1,4-cyclohexanedimethylene glycol units were split into the triad sequence in the chain and could be assigned by a comparison of the spectra with those of homopolymers and by an additional two-dimensional heteronuclear multiple bond correlation observation. The triad sequence distributions centered on 1,4-cyclohexanedimethylene glycol units were determined, which was independent of the cis- and trans-forms of the units and controlled according to Bernoullian statistics.     

Effects of Solvation and Ionization on 13C NMR Spectra of Lignin Model Compounds,Spruce Milled Wood Lignin and Kraft Lignin

The effects of alkali and polar aprotic solvent on the aromatic carbons signals in ¹³C NMR (Carbon-13 nuclear magnetic resonance) spectra of lignin model compounds and spruce milled wood lignin (MWL) were studied. It was found that in 1 M aqueous NaOH signal shifts of C-1 and C-4 carbon atoms in the aromatic ring were the most noticeable in lignin models with free phenolic hydroxyl groups, which are ionized under the conditions. A similar effect in the spectra of the studied model compounds was observed in 0.5 M aqueous NaOD-deuterated dimethyl sulfoxide (DMSO) mixture (DMSO: water ratio 3:7 v/v). The model data help explaining changes in the ¹³C NMR spectra of MWL and lignin in situ dissolved in spruce kraft black liquor caused by ionization. In the ¹³C NMR spectra of spruce black liquor the signals of phenolic and non-phenolic lignin units are clearly separated and do not overlap with the signals of the carbon atoms of carbohydrates and other aliphatic products of wood degradation. The data obtained are useful in understanding the important role of solvation and ionization processes leading to lignin solubilization.     

n-Butane conversion on sulfated zirconia: in situ 13C MAS NMR monitoring of the kinetics of the 13C-label scrambling and isomerization

The kinetics of the conversion of ¹³C-labeled n-butane adsorbed on sulfated zirconia (SZ) were monitored by in situ ¹³C MAS NMR spectroscopy. Rate constants of n- to isobutane isomerization and of the ¹³C-isotope scrambling from the primary to the secondary carbon atoms in n-butane were determined. The monomolecular scrambling of the ¹³C-label in adsorbed n-butane has an activation energy of 17 ± 3 kcal mol^–1 and occurs faster than the bimolecular process of n-butane isomerization which has an activation energy of 15.1 ± 0.2 kcal mol^–1. The transfer of the selective ¹³C-label from the primary to the secondary carbon atom in the adsorbed n-butane seems to consist of two reaction steps: (i) a hydride abstraction by SZ leading to the formation of sec-butyl cations and (ii) a label scrambling in the sec-butyl cations. This two-step process with the formation of sec-butyl cations as intermediate increases the apparent activation energy for the ¹³C-label scrambling, which is almost twice as large compared with the activation energy for carbon scrambling of sec-butyl cations in a superacidic solution.     

THE STRENGTH OF MUTAGENICITY, 13C NMR CHEMICAL SHIFTS,AND ELECTRONIC STATES OF NITROBENZANTHRONES

Mutagenic activities of nitrated benzanthrones (NBAs) vary largely with the position and the number of the nitro group. To investigate the structure-activity correlations for NBAs, we have performed nuclear magnetic resonance (NMR) measurements and molecular orbital calculations for the three nitrobenzanthrones, 2-NBA, 3-NBA, 11-NBA; the three dinitrobenzanthrones, 1,9-DNBA, 3,11-DNBA, 3,9-DNBA; and the trinitrobenzanthrone, 3,9,11-TNBA. It was confirmed that the ¹³ C chemical shifts (δ) of the ortho carbon atoms with respect to the nitro group of the compounds tend to be more upfield with decreasing mutagenic activities. The molecular orbital calculations revealed that the LUMO energies of the compounds decrease with mutagenic activities, and that the HOMO and LUMO densities tend to decrease and increase, respectively, with decreasing mutagenic activities. These results indicate that reduction is very important in the metabolism of nitrobenzanthrones.     

Determination of petroselinic acid inUmbelliflorae seed oils by combined GC and13C NMR spectroscopy analysis

Synthetic triolein and tripetroselinin mixtures were examined by¹³C NMR spectroscopy, showing marked chemical shift differences of the olefinic carbon atoms. Peak height ratios were compared to weight values for quantitative determination of oleic and petroselinic acids in seed oils, since these two fatty acids are quantitated together by GC analysis. Values observed for NMR peak height ratios were fairly close and agreed well with weight ratios. From overall compositions of eleic and petroselinic acids obtained by GC and relative compositions given by¹³C NMR, petroselinic acid has been determined in tenUmbelliflorae seed oils.     

13C NMR spectra of TAG: An easy way to distinguish milks from different animal species

In order to differentiate milks from different species, we carried out a comparative analysis of TAG from cow, buffalo, goat, and sheep milk fat based on ¹³C NMR experiments. NMR spectroscopy, although less sensitive than other techniques, does not require an extensive chemical manipulation of samples and can easily highlight the differences in the content of short-chain acyl groups in the four milk species. The resonances were assigned and quantified, and by using only three NMR parameters in data clustering with fuzzy logic analysis, we were able to distinguish goats' milk from sheep's milk, and both of these milks from cows' and buffaloes' milks. This appears to be an important result, considering the ease and rapidity with which milk identification can be obtained. From ¹³C NMR spectra of TAG, the positional distribution of FA chains on the glycerol backbone can also be easily evaluated. In particular, analysis of the positional distribution of monounsaturated FA revealed that it may be species-specific, and we are currently analyzing larger data sets in order to evaluate the use of this parameter as a suitable approach to address the issue of milk authenticity.     

Surface complexes in zeolite-catalysed acylation reactions detected by13C MAS NMR spectroscopy

The state of the acylating agent acetyl chloride, adsorbed on a series of proton and metal ion exchanged zeolites X, Y (faujasite) and ZSM-5, was investigated by¹³C MAS NMR spectroscopy. The observed carbonyl signals were assigned to two species: chemisorbed acetyl chloride bound to lattice oxygen (signals near 182 ppm), and acetyl chloride complexed with counter cations in the lattice (signals near 172 ppm). In a few cases signals were observed which have been assigned to free acylium cation stabilized on the surface of the solid (signal 160–165 ppm). Experiments in which toluene was adsorbed on to ZnY pretreated with acetyl chloride showed the participation of various adsorbed species in the acylation reaction of toluene.     

Solid-State 13C CP/MAS NMR for Alkyl-O-Aryl Bond Determination in Lignin Preparations

Several lignin preparations (Freudenberg lignin, Björkman lignin, and Pepper lignin), technical lignins (soda, soda-AQ, Kraft, Kraft-AQ, and hydrolysis), dimeric lignin model compounds, and different polysaccharides (galactoglucomannan, arabinogalactan, xylan, and arabinan) were analyzed by means of solid-state ¹³C CP/MAS NMR. Signals assignment in solid-state NMR lignin spectra was performed on the basis of the conducted studies and earlier published data. It was established that there exists strong linear correlation (r = 0.985) between Alkyl-O-Aryl inter-unit bond content in lignin and integral signals intensity in NMR spectra in the range of chemical shifts of 96–68 ppm. The integral signals intensity was measured in correlation with the reference integral signals in the range of chemical shifts of 162–102 ppm, typical for aromatic carbon atoms. To eliminate the effect, caused by carbohydrates contained in lignin, the correction factor of 0.67% of the area of integration per 1% of carbohydrates was determined. It was shown that the solid-state ¹³C CP/MAS NMR method allowed to determine Alkyl-O-Aryl bond content in both soluble and insoluble lignin preparations, and also to determine methoxyl groups content in soluble preparations.     

In-situ13C magic-angle-spinning NMR measurements of the conversion of ethene to aliphatic hydrocarbons over structurally different zeolites

Solid-state¹³C NMR analysis of the oligomerisation of ethene over H-ZSM-5, H-Y and H-mordenite, indicates that the degree of branching of the final products increases with increasing pore dimensions of the zeolite. In order to monitor the formation of intermediate reaction products, we investigated the oligomerisation of ethene in zeolite H-ZSM-5 at lower temperature. Ethene sorbed in ZSM-5 is stable below 0 °C, but at higher temperatures it is oligomerised to higher, branched reaction products. The use of sealed capsules enabled us to identify several (apparently highly reactive) higher olefins as intermediates. Although the observation of intermediate olefinic oligomers is in line with the classical reaction mechanism of acid-catalysed oligomerisation via carbenium ions, no such charged species could be detected. Alkoxide species, on the other hand, were observed, and these may very well be involved in the reactions.     

Characterization of one-step,chromate-free,primer systems using liquid-state Si and C NMR

Coatings derived from organofunctional silanes have been investigated as possible replacements for the chromate-based systems used in the aerospace industry. In this study, organofunctional silanes [bis-(triethoxysilylpropyl)ethane and bis(triethoxysilylpropyl) tetrasulfide] were reacted with commercially available acrylate (ECO-CRYL™ 9790) and epoxy (EPI-REZ™ WD-510) resins, resulting in a one-step, low-VOC, chromate-free primer. Liquid-state ²⁹Si and ¹³C NMR were used to determine structural characteristics of various optimized formulations.     

Analysis of sequence distribution in methyl methacrylate-methyl acrylate copolymers by C NMR spectroscopy

Methyl methacrylate (MMA)-methyl acrylate (MA) copolymers, prepared in bulk at 50 °C using AIBN as initiator, were characterized by 150 MHz ¹³C NMR spectroscopy, including use of the Distortionless Enhancement by Polarization Transfer (DEPT) experiment to obtain methylene and methine carbon resonances as subspectra. Dyad, triad, tetrad and partial pentad distributions were measured from the α-methyl, methine and methylene carbon resonances. These were in good agreement with distributions calculated for the copolymers based on monomer feed compositions, conversions and reactivity ratios of 2.60 and 0.27 for methyl methacrylate and methyl acrylate, respectively.     

A 13C and 15N Solid State NMR Study of the Reactions of Acetone Oxime Adsorbed on FeZSM-5

The reactions of acetone oxime, a proposed reaction intermediate for the SCR (Selective Catalytic Reduction) of NO with propane on FeZSM-5, have been studied with ¹³C and ¹⁵N solid state MAS NMR (magic angle spinning nuclear magnetic resonance). FeZSM-5 with three different loading levels was prepared by the sublimation method. The thermal reactions of acetone [2-¹³C] oxime adsorbed on FeZSM-5 samples with different iron loadings were monitored by ¹³C MAS NMR by heating to the desired temperature and then cooling to room temperature for data acquisition. For the sample with the lowest iron loading (Fe/Al = 0.11), acetic acid and N-methyl-2-propanamine were formed by the decomposition of acetone oxime. For the samples with the higher iron loadings (Fe/Al = 0.69 and 0.91), acetone, N,N-methyl-2,2-propanediamine, and N-methyl-2-propanimine were formed by the decomposition of acetone oxime. ¹⁵N MAS NMR was used to investigate reactions of ¹⁵NO and acetone oxime on the FeZSM-5 samples. The formation of gas phase N₂ and N₂O was observed.     

Use of 13C nuclear magnetic resonance distortionless enhancement by polarization transfer pulse sequence and multivariate analysis to discriminate olive oil cultivars

Distortionless enhancement by polarization transfer (DEPT) pulse sequence was used to set up a quantitative high-resolution ¹³C nuclear magnetic resonance (NMR) method to discriminate olive oils by cultivars and geographical origin. DEPT pulse sequence enhances the intensity of NMR signals from nuclei of low magnetogyric ratio. The nuclear spin polarization is transferred from spins with large Boltzmann population differences (usually protons) to nuclear species characterized by low Boltzmann factors, e.g., ¹³C. The signal enhancement of ¹³C spectra ensures the accuracy of resonance integration, which is a major task when the resonance intensities of different spectra must be compared. The resonances of triglyceride acyl chains C _n:0, C_18:1, C_18:2, and C_18:3, were also assigned. Multivariate analysis was carried out on the 35 carbon signals obtained. By using variable reduction techniques, coupled with standard statistical methods—partial least squares and principal components analysis—it was largely possible to separate the samples according to their variety and region of origin. With one problem variety removed, 100% prediction of the three remaining varieties was achieved. Similarly, by using the three regions with greatest representation in the data, all but one of a test set of 34 samples were correctly predicted. Thus, the composition of olive oils from different cultivars and of different geographical origin were compared and successfully studied by multivariate analysis. These considerations in conjunction with the structural elucidations of triglyceride molecules demonstrated that ¹³C NMR is among the most powerful techniques yet described for analysis of olive oils.     

C NMR study on structure, composition and curing behavior of phenol-urea-formaldehyde resole resins

Phenol-urea-formaldehyde (PUF) resole resins were synthesized and analyzed by both liquid and solid-state ¹³C nuclear magnetic resonance (NMR) spectroscopy. The liquid ¹³C NMR analysis indicated that the co-condensation reactions between the phenolic ring and the urea unit occurred during the synthesis of the resins. The addition of the urea component effectively reduced the free formaldehyde content in the resin systems. Methylene ether bridges in the resins were found to be mainly associated with the urea units. pH had significant influences on the structure and composition of the resins. Solid-state ¹³C NMR measurements of the cured resins suggested that the pH probably affected the curing mechanism. A longer time and a higher temperature can generally accelerate the curing process and increase the rigidity of the cured network.